Datalogic PowerScan BT8300 Family Quick Reference Manual

PowerScan™ BT8300 Family

Industrial Handheld

Bar Code Reader with

Bluetooth® Wireless Technology

Quick Reference Guide

Datalogic Scanning, Inc.

959 Terry Street

Eugene, Oregon 97402

USA

Telephone: [phone]

Fax: [phone]

An Unpublished Work - All rights reserved. No part of the contents of this documentation or the

procedures described therein may be reproduced or transmitted in any form or by any means with-

out prior written permission of Datalogic Scanning, Inc. or its subsidiaries or affiliates ("Datalogic"

or “Datalogic Scanning”). Owners of Datalogic products are hereby granted a non-exclusive, revo-

cable license to reproduce and transmit this documentation for the purchaser's own internal busi-

ness purposes. Purchaser shall not remove or alter any proprietary notices, including copyright

notices, contained in this documentation and shall ensure that all notices appear on any reproduc-

tions of the documentation.

Should future revisions of this manual be published, you can acquire printed versions by contact-

ing your Datalogic representative. Electronic versions may either be downloadable from the Data-

logic website (www.scanning.datalogic.com) or provided on appropriate media. If you visit our

website and would like to make comments or suggestions about this or other Datalogic publica-

tions, please let us know via the "Contact Datalogic" page.

Disclaimer

Datalogic has taken reasonable measures to provide information in this manual that is complete

and accurate, however, Datalogic reserves the right to change any specification at any time with-

out prior notice.

Datalogic and the Datalogic logo are registered trademarks of Datalogic S.p.A. in many countries,

including the U.S.A and the E.U. All other brand and product names referred to herein may be

trademarks of their respective owners.

Patents

This product is covered by one or more of the following patents:

Design Pat. AU 310201; AU 310202; CN 693980; CN735959; HK 0602013.5M001; HK

0602013.5M002; JP 1305693; KR 30-0460940; US D570,843 S; USD588,596 S.

US Pat. 5,992,740; 6,305,606 B1; 6,412,698 B2; 6,517,003; 6,808,114 B1; 6,997,385 B2;
7,387,246 B2; 5,367,151; 5,449,893; 5,545,889; 6,098,877; 6,220,514 B1; 6,412,698 B2;
6,607,132 B1; 6,817,529 B2; 6,834,805 B2.

European Pat. 789,315 B1; 895,175 B1; 1,128,314 B1; 1,128,315 B1; 1,396,811 B1;
1,413,971 B1; 1,816,585 B1; 1,942,442 B1.

Additional patents pending.

Quick Reference Guide 1

Table of Contents

Using the PowerScan™ BT8300....................................................................... 3

Scan Line Position .........................................................................................3

Reading Angle ................................................................................................3

Aiming System ...............................................................................................4

Installing the Battery Pack................................................................................. 5

Charging the Batteries ................................................................................. 7

Setup......................................................................................................................... 8

Restore PowerScan BT 8300 Default ......................................................8

Date and Time Setup ................................................................................... 8

Connecting the PowerScan BT8300.............................................................. 9

Overview ........................................................................................................... 9

PowerScan™ BT8300/BC 8030-BT Configuration ........................9

PowerScan™ BT8300/Bluetooth-Enabled PC Configuration .. 9

Before You Begin .........................................................................................10

Unpairing the Reader .........................................................................10

Linking the PowerScan™ BT8300 to the BC 8030-BT Cradle ........10

Link by Contact .....................................................................................11

Link by Inquiry .......................................................................................12

Link by Label ..........................................................................................12

Linking the PowerScan BT8300 to a Bluetooth-Enabled PC ........13

Linking to a PC in Serial Port Profile (Slave) Mode ...................13

Linking to a PC in Serial Port Profile (Master) Mode ................14

Linking to a PC in HID .........................................................................15

Variable PIN Code ................................................................................15

PowerScan BT8300 HID Configuration ................................................16

HID Country Codes ..............................................................................16

Caps Lock State ............................................................................................19

Caps Lock Auto-Recognition (IBM AT Compatible Only) ..............19

Alt Mode .........................................................................................................19

PowerScan™ BT8300 Default Configuration ........................................... 20

Technical Features............................................................................................ 21

Reading Distance .............................................................................................. 22

Warranty ............................................................................................................... 23

Service and Support ......................................................................................... 23

Compliance ......................................................................................................... 24

FCC Compliance ...........................................................................................24

Radio Compliance .......................................................................................24

2 PowerScan® BT8300

Laser Safety Compliance .......................................................................... 24

LED CLASS ..................................................................................................... 25

IC (Industry Canada) ................................................................................... 25

WEEE Compliance ....................................................................................... 26

Hex/Numeric Table ........................................................................................... 27

Quick Reference Guide 3

PowerScan™ BT8300 Reader

Using the PowerScan™ BT8300

The PowerScan™ BT8300 family of readers can be used with either the
PowerScan BC 8030-BT base station or a Bluetooth-enabled PC to build a
Cordless Reading System for the collection, decoding and transmission of bar
coded data.

PowerScan

™

BT8300 laser readers automatically scan bar codes at a distance.

Simply aim and pull the trigger.

Scan Line Position

Code scanning is performed along the scan line emitted from the reading window.
This line must cross the entire code. The best reading angles are indicated in the
figure below:

Reading Angle

Successful scanning is obtained by tilting the reader with respect to the bar code to
avoid direct reflections that impair the reading performance, see the figure below.

Using the PowerScan™ BT8300

4 PowerScan™ BT8300

Aiming System

PowerScan™ BT8300 provides an aiming system. If enabled, a partial trigger
press produces a red spot, which should be aimed over the code center to get the
best reading performance, see (1) in the figure above. By completely pressing the
trigger the scan line appears to start the code scanning, see (2).

After setting up the reader

, you can enable or disable the aiming system by reading

the codes below:

Disable Aiming System (Default)

Ì$+Bj0$-"Î

Enable Aiming System

Ì$+Bj1$-'Î

Installing the Battery Pack

Quick Reference Guide 5

Installing the Battery Pack

To install, charge and/or do any other action on the battery, follow the
instructions in this manual.

To charge the Battery Pack, See “Charging the Batteries” on
page 7.

Datalogic recommends annual replacement of rechargeable
battery packs to ensure maximum performance.

WARNING

Do not discharge the battery using any device except for the
scanner. When the battery is used in devices other than the
designated product, it may damage the battery or reduce its
life expectancy. If the device causes an abnormal current to
flow, it may cause the battery to become hot, explode or ignite
and cause serious injury.
Lithium-ion battery packs may get hot, explode or ignite and
cause serious injury if exposed to abusive conditions. Be sure to
follow the safety warnings listed below:

• Do not place the battery pack in fire or heat.

• Do not connect the positive terminal and negative terminal of
the battery pack to each other with any metal object (such as
wire).

• Do not carry or store the battery pack together with metal
objects.

• Do not pierce the battery pack with nails, strike it with a ham­mer, step on it or otherwise subject it to strong impacts or
shocks.

• Do not solder directly onto the battery pack.

• Do not expose the battery pack to liquids, or allow the battery
to get wet.

• Do not apply voltages to the battery pack contacts.

In the event the battery pack leaks and the fluid gets into your
eye, do not rub the eye. Rinse well with water and immediately
seek medical care. If left untreated, the battery fluid could
cause damage to the eye.

Installing the Battery Pack

6 PowerScan™ BT8300

As with other types of batteries, Lithium-Ion (LI) batteries will lose capacity over
time. Capacity deterioration is noticeable after one year of service whether the
battery is in use or not. It is difficult to precisely predict the finite life of a LI
battery, but cell manufacturers rate them at 500 charge cycles. In other words, the
batteries should be expected to take 500 full discharge / charge cycles before
needing replacement. This number is higher if partial discharging / recharging is
adhered to rather than full / deep discharging,

The typical manufacturer advertised useful life of LI batteries is one to three years,
depending on usage and number of charges, etc., after which they should be
removed from service, especially in mission critical applications. Do not continue
to use a battery that is showing excessive loss of capacity, it should be properly
recycled / disposed of and replaced. For most applications, batteries should be
replaced after one year of service to maintain customer satisfaction and minimize
safety concerns.

Collect and recycle waste batteries separately from the device in comply with
European Directive 2006/66/EC, 2002/95/EC, 2002/96/EC and subsequent
modifications, US and China regulatory and others laws and regulations about the
environment.

CAUTION

Always charge the battery at 32° – 113°F (0° - 45°C) tempera­ture range.

Use only the authorized power supplies, battery pack, char­gers, and docks supplied by your Datalogic reseller. The use of
any other power supplies can damage the device and void your
warranty.

Do not disassemble or modify the battery. The battery contains
safety and protection devices, which, if damaged, may cause
the battery to generate heat, explode or ignite.

Do not place the battery in or near fire, on stoves or other high
temperature locations.

Do not place the battery in direct sunlight, or use or store the
battery inside cars in hot weather. Doing so may cause the bat­tery to generate heat, explode or ignite. Using the battery in
this manner may also result in a loss of performance and a
shortened life expectancy.

Do not place the battery in microwave ovens, high-pressure
containers or on induction cookware.

Immediately discontinue use of the battery if, while using,
charging or storing the battery, the battery emits an unusual
smell, feels hot, changes color or shape, or appears abnormal
in any other way.

Do not replace the battery pack when the device is turned on.

Do not remove or damage the battery pack’s label.

Do not use the battery pack if it is damaged in any part.

Battery pack usage by children should be supervised.

Installing the Battery Pack

Quick Reference Guide 7

Charging the Batteries

Once the BC 8030-BT/C-8000 is powered, you can charge the reader's batteries.
Place the PowerScan

™

BT8300 into the BC 8030-BT cradle or the C-8000

battery charger. The Reader LED on the cradle/battery charger turns red.

The battery is completely charged when the Reader LED on the cradle/battery
charger turns green.

Figure 1.

Changing the Batteries

Do not incinerate, disassemble, short terminals or expose to high
temperature. Risk of fire, explosion. Use specified charger only.
Risk of explosion if the battery is replaced by an incorrect type.
Dispose of the batteries as required by the relevant laws in force.

WARNING

1

2

Setup

8 PowerScan™ BT8300

Setup

Restore PowerScan BT 8300 Default

Before starting configuration and every time you want to restore factory settings,
read the label below. Please note that the default mode on PowerScan BT8300 is
Handheld - Cradle communication:

Restore PowerScan BT 8300 Default

Date and Time Setup

Scan the following bar codes in sequence to set the date and time for the
PowerScan BT8300.

1.

Enter Configuration

2.

Set Date

3.

+

Six digits for Day, Month and Year (DDMMYY)

4.

Set Time

5.

+

Four digits for Hours and Minutes (HHMM)

6.

Exit and Save Configuration

Connecting the PowerScan BT8300

Quick Reference Guide 9

Connecting the PowerScan BT8300

Overview

PowerScan™ BT8300/BC 8030-BT Configuration

1. Connect a BC 8030-BT cradle to the Host. For installation and connec­tion information see the BC 8030-BT Quick Reference Guide.

2. Charge the PowerScan BT8300 battery using a BC 8030-BT, the
CHR-PM80 or BC-P080 chargers as described in this Quick Reference
Guide. A full charge takes 4 hours if using an external power supply;
while it takes up to 10 hours if supplying power through the USB port.

3. Configure the reader as described in this Quick Reference -

Linking the PowerScan™ BT8300 to the BC 8030-BT Cradle on
page 10.

4. Configure the BC 8030-BT cradle. See BC 8030-BT Configuration in
the BC 8030-BT Quick Reference.

- OR -

PowerScan™ BT8300/Bluetooth-Enabled PC Configuration

1. Install any drivers provided with the Bluetooth adapter.

2. Charge the PowerScan™ BT8300 battery using a BC-8030-BT, the
CHR-PM80 or the MC-P080 chargers as described in this Quick Refer­ence Guide. A full charge takes 4 hours if using an external power supply;
while it takes up to 10 hours if supplying power through the USB port.

3. Configure the reader as described in this Quick Reference -

Linking the PowerScan BT8300 to a Bluetooth-Enabled PC on
page 13.

Connecting the PowerScan BT8300

10 PowerScan™ BT8300

Before You Begin

In order to use the connection procedures below, the handheld and base station
must be in an UNPAIRED state. If the reader is connected to a device, you must
follow the procedure below to UNPAIR the Base Station and the handheld before
attempting to link to a new device. If the handheld is not already connected to
another device, then you can skip this step and go straight to the Linking
instructions that begin on the next page.

Unpairing the Reader

To unpair the PowerScan BT8300 reader from a BC 8030-BT base station, press
and hold the button on the BC 8030-BT (>8 seconds), then read the Unpair bar
code below with each PowerScan BT8300 which you want to unpair from the
cradle.

You can Unpair the PowerScan BT8300 reader from a Bluetooth-Enabled PC to
make it available for pairing with another PC. Read the bar code above to
disconnect the reader from its PC

Please note that in order to connect different scanners to a Base that is already
connected to the maximum four scanners, you must follow the procedure above.

Linking the PowerScan™ BT8300 to the BC 8030-BT Cradle

The PowerScan BT 8300 reader can be connected with the PowerScan BC 8030­BT cradle in either of three ways.

After the BC-8030-BT cradle is powered on and connected to the Host, configure
the Power Scan BT8300 by reading the following bar codes in the given sequence
as described in each section.

Unpair

Remember: The mandatory condition for establishing a new
connection between a BT reader and a BT cradle is that they
share the same security configuration. The connection timeout
is 30 seconds. Four ascending beeps from the reader indicate a
successful link, otherwise there are four descending tones.

Connecting the PowerScan BT8300

Quick Reference Guide 11

Link by Contact

Read the bar codes in sequence as shown in the steps below:

5. Firmly position the reader onto the cradle. The BC 8030-BT cradle will
emit a beep and the yellow LED will blink while the cradle is trying to
establish the connection.

Four ascending beeps will be emitted, signaling that the BC 8030-BT cra­dle has been successfully connected to the PowerScan BT8300, and the
yellow LED on the cradle will stop blinking.

6. To connect another PowerScan PBT8300 to the BC 8030-BT cradle,
repeat the sequence from steps 1 through 5. One Cradle can connect with
a maximum of four readers.

7. Upon completing the connection between the reader and cradle you must
set up the correct interface for your system. Refer to the BC 8030-BT Base
Station Charger QRG for information and programming labels, and scan
the appropriate bar code to select your system’s interface type.

END of procedure. YOUR READER IS NOW READY TO READ CODES.

1.

Enter Configuration

2.

Handheld - Cradle

3.

Link by Contact

4.

Exit and Save Configuration

Connecting the PowerScan BT8300

12 PowerScan™ BT8300

Link by Inquiry

4. To connect another PowerScan PBT8300 to the BC 8030-BT cradle,
repeat in the sequence from steps 1 through 3 before continuing. One Cra­dle can connect with a maximum of four readers.

5. Quickly press the button (<8 seconds and release) on the BC 8030-BT cra­dle. The yellow LED on the cradle will blink and it will search for any
PowerScan BT 8300 readers in radio range. After finishing, the cradle will
emit a beep and begin to link with PowerScan BT8300 readers found.

6. The green LED on each PowerScan BT8300 reader will blink when the
BC 8030-BT cradle tries to link with it. To confirm the connection with
the cradle, press the trigger on the reader within 10 seconds, before the
timeout expires.

7. Four ascending beeps will be emitted, signaling that the BC 8030-BT cra­dle has been successfully connected to the PowerScan BT8300, and the
green LED on the reader will stop blinking.

8. Upon completing the connection between the reader and cradle you must
set up the correct interface for your system. Refer to the BC 8030-BT Base
Station Charger QRG for information and programming labels, and scan
the appropriate bar code to select your system’s interface type.

END of procedure. YOUR READER IS NOW READY TO READ CODES.

Link by Label

You can create a label that includes the appropriate command and the cradle
MAC address. Please refer to the Product Reference Guide (PRG), or contact
Technical Support for more information.

1.

Enter Configuration

2.

Handheld - Cradle

3.

Exit and Save Configuration

Connecting the PowerScan BT8300

Quick Reference Guide 13

Linking the PowerScan BT8300 to a Bluetooth-Enabled PC

The PowerScan BT8300 reader can optionally be linked to a Bluetooth-enabled
host with the serial port profile (SPP) or human interface device (HID) as a virtual
keyboard.

Linking to a PC in Serial Port Profile (Slave) Mode

To link a PowerScan BT8300 reader in Serial Port Profile (Slave) Mode to a
Bluetooth-enabled host, read the following codes in the given sequence.

4. Use the HOST computer's Bluetooth manager to "Add Bluetooth Device
Wizard" and select "PowerScan BT8300." When prompted for a passkey,
enter the default of "1234" or whatever you have already assigned to your
scanner. A window will notify you of Incoming Port and Outcoming Port
when the PowerScan BT8300 is successful added to the PC.

5. Open the Outcoming Port using your application program; for test pur­poses you can verify the communication using the Hyperterminal tool in
Windows.

6. Four ascending beeps will be emitted, signaling that the PowerScan
BT8300 has been successfully connected to the Bluetooth-enabled PC.

END of procedure. YOUR READER IS NOW READY TO READ CODES.

Depending on the driver used by your device, specific actions
may be required the first time a connection is made between the
PowerScan PBT8300 and a generic Bluetooth peripheral. For fur­ther information, download “Initial Bluetooth Connection
Guide,” available on the Datalogic website in the PowerScan BT
section.

1.

Enter Configuration

2.

Serial Port Profile (Slave)

3.

Exit and Save Configuration

Connecting the PowerScan BT8300

14 PowerScan™ BT8300

Linking to a PC in Serial Port Profile (Master) Mode

To link a PowerScan BT8300 reader in Serial Port Profile (Master) Mode to a
Bluetooth-enabled host, follow the instructions below and read the bar codes in
the given sequence.

1. Select the "COM Ports" tab on the Window's Bluetooth Manager and add
the Incoming Port. You will receive a notification that the Incoming Port is
added successfully.

2. Open the Incoming Port using your application program; for test purposes
you can verify the communication using the Hyperterminal tool in Win­dows.

6. When prompted for a passkey, enter the default of "1234" or whatever you
have already assigned to your scanner.

7. Four ascending beeps will be emitted, signaling that the PowerScan
BT8300 has been successfully connected to the Bluetooth-enabled PC and
the Green LED on the reader will stop blinking.

END of procedure. YOUR READER IS NOW READY TO READ CODES.

1.

Enter Configuration

2.

Serial Port Profile (Master)

3.

Host Address

4.

+

12 digits for the Host Bluetooth adapter

5.

Exit and Save Configuration

Connecting the PowerScan BT8300

Quick Reference Guide 15

Linking to a PC in HID

To link a PowerScan BT8300 reader in HID to a Bluetooth-enabled PC, please
read the following bar codes in the given sequence:

4. Use the host computer's Bluetooth Manager to "Add Bluetooth Device
Wizard" and select "PowerScan BT8300." In the next window, enter the
PIN code if you are using Security Mode 2 or Security Mode 3, or choose
"Don't use passkey" if you set Security Mode 1.

5. Four ascending beeps will be emitted, signaling that the PowerScan
BT8300 has been successfully connected to the Bluetooth-enabled PC.

END of procedure. YOUR READER IS NOW READY TO READ CODES.

Variable PIN Code

Some Bluetooth drivers on the Host (such as WIDCOMM and BlueSoleil 8)
require a Variable PIN Code. When attempting connection, the application
presents a window that includes a PIN Code which is to be input using the
PowerScan BT8300. Please read the bar code "Variable PIN Code" and restart the
sequence from step 4 above.

Variable PIN Code

When you hear the beep indicating the reader is waiting for an alphanumeric
entry, enter the variable PIN Code one of two ways:

Keypad (PBT8300 16-key DK only): Type the PIN Code on the scanner

keypad, then tap

Enter ().

Scanning: Read the bar code corresponding with the require PIN Code and

ending with Exit and Save configuration label. Use the labels in the HEX/
NUMERIC KEYPAD section at the back of this manual for alphanumeric entry.

1.

Enter Configuration

2.

HID Profile

3.

Exit and Save Configuration

The default Security Mode in HID mode is Authentication and
Encryption Disable.

Connecting the PowerScan BT8300

16 PowerScan™ BT8300

PowerScan BT8300 HID Configuration

HID Country Codes

*Country Code = U.S

Country Code = Italy

Country Code = France

Country Code = Germany

Country Code = Britain

Country Code = Sweden

Country Code = Spain

*Default value

Connecting the PowerScan BT8300

Quick Reference Guide 17

HID Country Codes (cont.)

Country Code = Belgium

Country Code = Japanese 106-key

Country Code = Poland

Country Code = Hungary

Country Code = Croatia

Country Code = Romania

Country Code = Czech Republic

Country Code = Slovakia

Connecting the PowerScan BT8300

18 PowerScan™ BT8300

HID Country Codes (cont.)

Country Code = Denmark

Country Code = Norway

Country Code = Portugal

Country Code = Switzerland

Connecting the PowerScan BT8300

Quick Reference Guide 19

Caps Lock State

This option specifies the format in which the reader sends character data.

Caps Lock Auto-Recognition (IBM AT Compatible Only)

Alt Mode

*Caps Lock State = Caps Lock OFF

Caps Lock State = Caps Lock ON

*Enable

Disable

*Disable

Enable

*Default value

PowerScan™ BT8300 Default Configuration

20 PowerScan™ BT8300

PowerScan™ BT8300 Default Configuration

DATA FORMAT

Code identifier disabled, Field adjustment disabled, Code length not transmitted,
Character replacement disabled

CODE SELECTION

Enabled Codes

• EAN 8/EAN 13 / UPC A/UPC E without ADD ON
Check digit transmitted, no conversions

• Interleaved 2/5
Check digit control and transmission, variable length code; 4-99 char­acters

•Standard Code 39
No check digit control, variable length code; 1-99 characters

• Code 128
variable length code; 1-99 characters

Disabled Codes

EAN 128, ISBT128, Code 93, Codabar, pharmaceutical codes, MSI, Code 11, Code
16K, Code 49, GS1 DataBar™ (GS1 DataBar includes the following symbologies:
GS1 DataBar Omnidirectional, GS1 DataBar Stacked, GS1 DataBar Expanded and
GS1 DataBar Limited).

RADIO PARAMETERS

Security Mode = 1 (Handheld - Cradle role and HID role) = 2 (Serial Port Profile
Master and Serial Port Profile Slave); Default PIN code = 1234; Default Friendly
Name = POWERSCAN BT8300 + SERIAL_NUMBER; Default power class = 1; Default
role = Reader communicates with Base; Poweroff timeout = 4 hours; Autoconnect
enable, Autoreconnect enable, Batch Mode disable.

OPERATIVE MODE (DK Models only)

Simple Data Input Mode

FUNCTION KEYS DEFAULT (DK Models only)

•F1- backlight (label: “Lgt”)

• F2- insert a dot in the edit field (label: “[ . ]”)

• F3- backspace (label: “

←”)

• F4- clear the display (label: “CLR”)

Technical Features

Quick Reference Guide 21

Technical Features

Electrical Features

Battery Type 2150 Li-Ion battery pack

Time of recharge max. 4 hours with external power supply

max. 10 hours with Host power

Operating autonomy
(continuous reading)

50,000 reads (typical)

Display LCD 4 lines x 16 chars

Programmable LED backlight

Indicators Good Read LED green;

Good Read Spot green; Beeper

Laser Features BT8300 BT8300-AR

Power (max) in mW 0.9 mW 1.3 mW

Light Source VLD in the range between 630~680 nm

Scan Rate 35 ± 5 scans/sec

Reading Field Width

(typical) see reading diagram

Max. Resolution 0.076 mm (3 mils) 0.19 mm (7.5 mils)

PCS minimum
(Datalogic Test Chart)

15% 25%

Scan Angle 42° 13.5°  0.7

Laser Safety Class 2 (EN 60825-1 / CDRH)

Bluetooth Features

Protocol Bluetooth 2.0; Class 1 or Class 2 configurable; SPP

(Serial Port Profile) or HID (Human Interface
Device) profile

Radio Frequency 2.40 to 2.48 GHz

Environmental Features

Working Temperature -20° to +50 C / -4 to +122 °F

Storage Temperature -20° to +70 C / -4 to +158 °F

Humidity 90% non condensing

Drop resistance

(on concrete)

2 m

Protection Class IP64 (with display); IP65 (without display)

Mechanical Features

Weight (with batteries) about 400 g (14.10 oz)

Dimensions 212 x 109 x 71 mm (8.34 x 4.29 x 2.79 in)

Material Polycarbonate molded with rubber

Keyboard BT8300: no keyboard or display

BT8300-D: 3 key keypad and display
BT8300-DK: 16 key keypad and display

Reading Distance

22 PowerScan™ BT8300

Reading Distance

PowerScan™ BT8300

PowerScan™ BT8300 AR

mil Typical reading distance with good quality codes

5 2.1 - 13.3 cm / 0.8 - 5.2 in

7,5 3.5 - 24.2 cm / 1.4 - 9.5 in

10 2.9 - 42.8 cm / 1.1 - 16.8 in

13 2.3 - 55.1 cm / 0.9 - 21.7 in

20 6.3 - 78.5 cm / 2.5 - 30.9 in

40 2.5 - 97.8 cm / 1.0 - 38.5 in

mil Typical reading distance with good quality codes

7,5 18 - 50 cm / 7.0 - 19.7 in

10 18 - 85 cm / 7.0 - 33.5 in

15 15 - 165 cm / 5.9 - 65.0 in

20 12 - 210 cm / 4.7 - 82,7 in

40 18 - 375 cm / 7.0 - 147.6 in

55 25 - 485 cm / 9.8in - 15.9 ft

100
(refl. Paper)

1.5 - 12.5 m / 4.9 - 41.0 ft

Warranty

Quick Reference Guide 23

Warranty

Datalogic warranties this product against defects in workmanship and materials,
for a period of 3 years from the date of shipment, provided that the product is
operated under normal and proper conditions.

Datalogic has the faculty to repair or replace the product; these provisions do not
prolong the original warranty term. The warranty does not apply to any product
that has been subject to misuse, accidental damage, unauthorized repair or
tampering.

Service and Support

Datalogic provides several services as well as technical support through its website.
Log on to www.scanning.datalogic.com and click on the links indicated for
further information including:

•PRODUCTS

Search through the links to arrive at your product page where you can
download specific Manuals and Software & Utilities including:

- Datalogic Aladdin

™

, a multi-platform utility program that allows device
configuration using a PC. It provides RS-232 and USB-COM interface
configuration, as well as configuration bar code printing.

•SERVICE & SUPPORT

- Technical Support - Product documentation and programming guides and
Technical Support Department in the world

- Service Programs - Warranty Extensions and Maintenance Agreements

- Repair Services - Flat Rate Repairs and Return Material Authorization
(RMA) Repairs.

- Downloads – Manuals & Documentation, Data Sheets, Product Cata­logues, etc.

•CONTACT US

Information Request Form and Sales & Service Network

Compliance

24 PowerScan™ BT8300

Compliance

This device must be opened by qualified personnel only.
The batteries must be removed before opening the device.

FCC Compliance

Modifications or changes to this equipment without the expressed written
approval of Datalogic could void the authority to use the equipment.

This device complies with PART 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference which
may cause undesired operation.

FCC ID U4F0015.

Radio Compliance

Contact the competent authority responsible for the management of radio
frequency devices of your country to verify any possible restrictions or licenses
required.

Refer to the web site http://europa.eu.int/comm/enterprise/rtte/spectr.htm for
further information.

Laser Safety Compliance

The laser scanner conforms to the applicable requirements of both CDRH 21
CFR 1040 and EN60825-1 at the date of manufacture.

The laser light is visible to the human eye and is emitted from the output window
(1).

Laser warning and classification label (2).

Compliance

Quick Reference Guide 25

The laser scanner utilizes a low-power laser diode. Although staring directly at the
laser beam momentarily causes no known biological damage, avoid staring at the
beam as one would with any very strong light source, such as the sun. Avoid that
the laser beam hits the eye of an observer, even through reflective surfaces such as
mirrors, etc.

The following information is shown on the laser scanner device class label:

LED CLASS

Class 1 LED product.

This product conforms to EN60825-1:2001.

IC (Industry Canada)

Operation is subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.

La utilización de procedimientos o regulaciones diferentes de
aquellas describidas en la documentación puede causar una
exposición peligrosa a la luz láser visible.

CAUTION

ITALIANO
Classe 2:

LUCE LASER
NON FISSARE IL RAGGIO
APPARECCHIO LASER DI

CLASSE 2

DEUTSCH
Klasse 2:

LASERSTRAHLUNG
NICHT IN DEN STRAHL
PRODUKT DER LASERKLASSE 2

FRANÇAIS
Classe 2:

RAYON LASER
EVITER DE REGARDER LE

RAYON
APPAREIL LASER DE

CLASSE 2

ESPAÑOL
Clase 2:

RAYO LÁSER
NO MIRAR FIJO EL RAYO
APARATO LÁSERDE CLASE 2

Compliance

26 PowerScan™ BT8300

WEEE Compliance

English

For information about the disposal of Waste Electrical and Electronic Equipment
(WEEE), please refer to the website at www.scanning.datalogic.com.

Italian

Per informazioni sullo smaltimento delle apparecchiature elettriche ed
elettroniche consultare il sito Web www.scanning.datalogic.com.

French

Pour toute information relative à l’élimination des déchets électroniques (WEEE),
veuillez consulter le site Internet www.scanning.datalogic.com.

German

Informationen zur Entsorgung von Elektro- und Elektronik- Altgeräten (WEEE)
erhalten Sie auf der Webseite www.scanning.datalogic.com.

Spanish

Si desea información acerca de los procedimientos para el desecho de los residuos
del equipo eléctrico y electrónico (WEEE), visite la página Web
www.scanning.datalogic.com.

Portuguese

Para informações sobre a disposição de Sucatagem de Equipamentos Eléctricos e
Eletrônicos (WEEE - Waste Electrical and Electronic Equipment), consultar o site
web www.scanning.datalogic.com.

Chinese

有关处理废弃电气电子设备 (WEEE) 的信息， 请参考 Datalogic 公司的网站：
http://www.scanning.datalogic.com/。

Japanese

廃電気電子機器 (ＷＥＥＥ) の処理についての関連事項は Datalogic のサイト
www.scanning.datalogic.com, をご参照下さい。

Waste Electrical and Electronic Equipment (WEEE) Statement

Hex/Numeric Table

Quick Reference Guide 27

Hex/Numeric Table

Ì01Î

0

Ì12Î

1

Ì23Î

2

Ì34Î

3

Ì45Î

4

Ì56Î

5

Ì67Î

6

Ì78Î

7

Ì89Î

8

Ì9:Î

9

Hex/Numeric Table

28 PowerScan™ BT8300

Hex/ Numeric Table (continued)

A

B

C

D

E

F

Cancels an incomplete configuration sequence

Exit and Save Configuration

dichiara che
declares that the
déclare que le
bescheinigt, daß das Gerät
declare que el

PowerScan BT83xx; Cordless Bar Code Reader

sono conformi alla Direttiva del Consiglio Europeo sottoelencata:
are in conformity with the requirements of the European Council Directive listed below:
sont conformes aux spécifications de la Directive de l'Union Européenne ci-dessous:
der nachstehenden angeführten Direktive des Europäischen Rats entsprechen:
cumple con los requisitos de la Directiva del Consejo Europeo, según la lista siguiente:

Questa dichiarazione è basata sulla conformità dei prodotti alle norme seguenti:
This declaration is based upon compliance of the products to the following standards:
Cette déclaration repose sur la conformité des produits aux normes suivantes:
Diese Erklärung basiert darauf, daß das Produkt den folgenden Normen entspricht:
Esta declaración se basa en el cumplimiento de los productos con las siguientes normas:

Datalogic Scanning, Inc.

07

959 Terry Street

Eugene, OR 97402

e tutti i suoi modelli
and all its models
et tous ses modèles
und seine Modelle
y todos sus modelos

1999/5/EEC R&TTE

ETSI EN 301 489-3 v1.4.1, August 2002: ElectroMagnetic Compatibility and Radio spectrum

Matters (ERM); ElectroMagnetic Compatibility (EMC)
standard for radio equipment and services; Part 3:
Specific conditions for Short-Range Devices (SRD)
operating on frequencies between 9 kHz and 40 GHz

ETSI EN 300 220-3 v1.1.1, September 2000: Electromagnetic compatibility and Radio spectrum

Matters (ERM); Short Range Devices (SRD); Radio
equipment to be used in the 25 MHz to 1000 MHz
frequency range with power levels ranging up to 500
mW; Part 3: Harmonized EN covering essential
requirements under article 3.2 of the R&TTE Directive

EN 60950-1, December 2001: I

NFORMATION TECHNOLOGY EQUIPMENT – SAFETY –

Part 1: General requirements

December 14th, 2007

©2010-2011 Datalogic Scanning, Inc. 820033914 (Rev B) May-2011

Australia

Datalogic Scanning Pty Ltd
Telephone: [61] (2) 9870 3200
[e-mail]

France and Benelux

Datalogic Scanning SAS
Telephone: [33].01.64.86.71.00
[e-mail]

Germany

Datalogic Scanning GmbH
Telephone: [phone]
[e-mail]

India

Datalogic Scanning India
Telephone: 91- 22 - 64504739
[e-mail]

Italy

Datalogic Scanning SpA
Telephone: [39] (0) 39/62903.1
[e-mail]

Japan

Datalogic Scanning KK
Telephone: [phone]
[e-mail]

Latin America

Datalogic Scanning, Inc
Telephone: [phone]
[e-mail]

Singapore

Datalogic Scanning Singapore PTE LTD
Telephone: [phone]
[e-mail]

Iberia

Datalogic Scanning SAS Sucursal en
España
Telephone: [phone]
[e-mail]

United Kingdom

Datalogic Scanning LTD
Telephone: [phone]
[e-mail]

Datalogic Scanning, Inc.

959 Terry Street
Eugene, OR 97402
USA
Telephone: [phone]
Fax: [phone]

www.scanning.datalogic.com