Danfoss VLT Midi Drive FC 280 Installation guide

Drive

Description

Part number

VLT® Midi Drive FC 280

Terminals for enclosure sizes K1–K3. Plug item: 1, 2, 3, 4, 5, 6, 7.

132B0420

Terminals for enclosure sizes K4–K5. Plug item: 1, 2, 3, 4.

132B0421

VLT® Midi Drive FC 280 with Ethernet Safety Functions

Accessory bag, plugs K1–K3. Plug item: 1, 4, 5, 6, 7, 10, 11.

132B0798

Accessory bag, plugs K4–K5. Plug item: 1, 4, 10, 11.

132B0799

Description

Ordering number

Terminals for enclosure sizes K1–K5. Plug item: 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11.

132B0350

Installation Guide

Terminal Torque Instructions

VLT® Midi Drive FC 280

1 Installation Instructions

1.1 Description

These instructions give information on the torque values for the terminal blocks used in the VLT® Midi Drive FC 280.

1.2 Part Numbers

Table 1: Accessory Bag Numbers (Cannot be Ordered as Spare Parts)

Table 2: Spare Part Numbers

1.3 Safety Precautions

Only Danfoss qualified personnel is allowed to install this equipment. For important information about safety precautions for installation, refer to the drive's Operating Guide.

1.4 Tools Required

•

SZS 0.6x3.5 mm slot screwdriver.

1.5 Torque Instructions

N O T I C E

DESTRUCTION OF TERMINALS OR LOOSE CABLES

Applying too much torque can destroy the terminal blocks. Applying too low torque can result in loose cables.

Only use a screwdriver as specified in 1.4 Tools Required.

Apply the needed tightening torque as specified in Table 3.

Do not apply more torque than the maximum torque as specified in Table 3.

1 2 3

e30bf224.12

7 8

10 11

Item

Designation

Tightening torque [Nm (in-lb)]

Maximum torque [Nm (in-lb)]

Plug connector, relay 1

0.5 (4.4)

0.6 (5.3)

I/O terminal plug, 10-pole

0.35 (3.1)

0.4 (3.5)

I/O terminal plug, 5-pole

I/O terminal plug, 3-pole

Motor plug, 3-pole 7.62

≤4 mm2/AWG 12: 0.5 (4.4), >4 mm2/AWG 12: 0.7 (6.2)

≤4 mm2/AWG 12: 0.6 (5.3), >4 mm2/AWG 12: 0.8 (7.1)

BR DC plug, 3-pole 7.62

Mains plug, 3-pole 7.62

CANopen plug, 5-pole

0.5 (4.4)

0.6 (5.3)

PROFIBUS plug, 5-pole

IO plug, 5-pole, 5 mm

0.35 (3.1)

0.4 (3.5)

IO plug, 8-pole, 5 mm

Terminal Torque Instructions

Installation Guide

Installation Instructions

Illustration 1: Tightening Torque for Terminals

Table 3: Tightening Torque for Terminals

Danfoss A/S

Ulsnaes 1 DK-6300 Graasten vlt-drives.danfoss.com

Danfoss can accept no responsibility for possible errors in catalogs, brochures, and other printed material. Danfoss reserves the right to alter its products without notice. This also applies to products already on order provided that such alterations can be made without subsequential changes being necessary in specifications already agreed. All trademarks in this material are property of the respective companies. Danfoss and the Danfoss logotype are trademarks of Danfoss A/S. All rights reserved.

*132R0174*

*M0032201*