INSTRUCTIONS
MCI 15C, MCI 25C
Compressor Soft Starter
Montering - Mounting - Montage mm (inch)
047C0427
Mål - Dimensions - Abmessungen mm (inch)
MCI 15C
DK Hvis enhed er monteret vandret reducer strøm med 50%
UK If unit is mounted horizontally derate current by 50%
D Falls Einheit horizontal montiert wird, reduziert sich der Strom
um 50%.
DK Køleplade skal holdes ren. Luftstrøm må ikke blokeres
UK Keep heat sink clean. Airflow should not be blocked
D Kühlflächen freihalten. Luftstrom muß ungehindert fließen
M
CI 25C
047C0427
Indstilling-Setting-Einstellung-Réglage
DK Soft start parametre ikke justerbar. Start tid maks. 0.6 sek.
UK Soft start parameters not adjustable. Start-up max. 0.6 sec.
Forbindelse - Wiring - Verdrahtung
7
5°C
Kabel/ Wire mm2(AWG) mm2 (AWG)
*
*
*
0.75 - 4 0
(18 - 12) (20 - 16)
2 x 1 2
(2 x 18) (2 x 20 - 18)
0.75 - 6 0
(18 - 10) (20 - 16)
2 x 0.75 - 2.5 2 x 0.5 - 1.5
(
2 x 18 - 14) (2 x 20 - 16)
0.75 - 6 0
(18 - 10) (20 - 16)
2 x 0.75 - 1.5 2 x 0.5 - 1.5
(
2 x 18 - 16) (2 x 20 - 16)
Pozidrive 1
0
.5 Nm max. N.A.
4.4 lb-in max.
4 mm 3
0.5 Nm max. 0.4 Nm max.
4.4 lb-in max. 3.5 lb-in max.
.5 - 1.5
x 0.5 - 0.75
.5 - 1.5
.5 - 1.5
mm
D Softstart Parameter nicht einstellbar. Anlaufzeit max. 0.6 Sek.
F Paramètre non ajustables, temps de démarrage max = 0.6 s
Motor Danfoss
Use UL listed
ma
gnetic circuit
breaker or UL
specified back-up fuse
type K5 or H Class
A
0.63 - 1.00 047B3024
1.00 - 1.63 047B3025
1.6 - 2.5 047B3026
2.5 - 4.0 047B3027
4.0 - 6.3 047B3028
6 - 10 047B3029
10 - 16 047B3030
16 - 20 047B3031
20 - 25 047B3032
*Afhængig af type
Depends
Abhängig vom Typ
Suivant modèles
CTI 25
on the type
L: Use thermal overload protection as required by the National Electric Code
U
UL: When protected by a non-time delay K5 or H Class fuse, rated 266% of motor FLA, this device is rated
for use on a circuit capable of delivering not more than 5,000 rms. symmetrical amperes, 600 V
maximum. Maximum ambient temperature 40°C
© Danfoss | DCS (rja) | 2015-09 IC.PI.C50.P2.51
520B6907