User Manual
Plus+1® Compliant
HMK_Brightness Function Block
www.danfoss.com
User Manual
Plus+1 Compliant® HMK_Brightness Function Block
Revision history Table of revisions
Date Changed Rev
April 2019 First edition 0101
2 | © Danfoss | April 2019 AQ299264497162en-000101
User Manual
Plus+1 Compliant® HMK_Brightness Function Block
Contents
HMK_Brightness
Overview..............................................................................................................................................................................................4
Inputs....................................................................................................................................................................................................5
Parameters..........................................................................................................................................................................................5
Outputs................................................................................................................................................................................................ 5
Diagnostic Signals............................................................................................................................................................................6
Status and Fault Logic.....................................................................................................................................................................6
Status Logic...................................................................................................................................................................................6
Fault Logic..................................................................................................................................................................................... 6
©
Danfoss | April 2019 AQ299264497162en-000101 | 3
User Manual
Plus+1 Compliant® HMK_Brightness Function Block
HMK_Brightness
Overview
This function block configures the function for use with the HMK and is used to send out the Global
Brightness settings of the LEDs.
4 | © Danfoss | April 2019 AQ299264497162en-000101
User Manual
Plus+1 Compliant® HMK_Brightness Function Block
HMK_Brightness
Inputs
Entering the HMK_Brightness function block gives an overview about the block’s signals.
To avoid compiler errors, use only the data types specified in this table.
Function Block Inputs
Input Type Range Unit Description
CAN.Port PORT -- -- Determines which physical CAN port of the hardware to receive data from.
Red U16 0 to 10000 0.01%
Green U16 0 to 10000 0.01%
Blue U16 0 to 10000 0.01%
White U16 0 to 10000 0.01%
Send BOOL T/F --
This variable can be found in the CAN sub-bus if using the Main Template.
Global brightness of RED Color.
0: No Change
1: Min Brightness
… :
10000: Max Brightness
Global brightness of GREEN Color.
0: No Change
1: Min Brightness
… :
10000: Max Brightness
Global brightness of BLUE Color.
0: No Change
1: Min Brightness
… :
10000: Max Brightness
Global brightness of WHITE.
0: No Change
1: Min Brightness
… :
10000: Max Brightness
False to true transition will send the specified command.
T: Positive transition will send the command
F: Do not send command
Parameters
Learn how the function block uses parameters to customize the function.
To avoid compiler errors, use only the data types specified in this table.
Function Block Parameters
Parameter Type Range Unit Description
Src_Addr U8 0 to 253 -- Source Address of the local device.
Dest_Addr U8 0 to 253 -- Destination Address of the HMK.
Outputs
Learn how the outputs of the function block work.
Function Block Outputs
Parameter Type Range Unit Description
OR BOOL T/F -- CAN Tx OverRun Flag.
Pend BOOL T/F -- CAN Tx Pending Flag.
Diag BUS -- -- This bus provides diagnostic values for troubleshooting. In addition, all
©
Danfoss | April 2019 AQ299264497162en-000101 | 5
inputs, parameters, and output signals are contained inside of the bus.
User Manual
Plus+1 Compliant® HMK_Brightness Function Block
HMK_Brightness
Function Block Outputs (continued)
Parameter Type Range Unit Description
Status U16 0, 0x8008 --
Fault U16 0, 0x8002 --
Diagnostic Signals
The diagnostic bus contains signals for input, parameter, output, and internal signals. Only the internal
signals are explained below. Input, parameter, and output signals are described in the above chapters.
Function Block Diagnostic Signals
Name Type Range Unit Description
CAN_ID U32 -- -- The resulting 29-bit J1939 ID.
CAN_Data ARRAY[8
]U8
CAN_Send BOOL T/F --
-- -- Data that is to be sent over CAN.
This signal indicates if a parameter fault is declared. It’s a bitwise code, so
multiple items can be reported at a time. The following status codes are
provided:
0x0000: No fault
0x8008: At least one parameter is out of range
This signal indicates if an input fault is declared. It’s a bitwise code, so
multiple items can be reported at a time. The following fault codes are
provided:
0x0000: No fault
0x8002: An input value is too high
Pulses true when a message is being sent.
T: Pulse triggered
F: Idle
Status and Fault Logic
This topic describes how status and fault logic is indicated for the function block.
Status Logic
The status code indicates whether the parameters used in the function are within their valid range.
Status Logic
Condition Hex
Invalid Setup 0x8008 1000 Dest_Addr > 253, Src_Addr >
*
Bit 16 set to 1 identifies a standard Danfoss status or fault code.
*
Binary Cause Response Correction
253
Fault Logic
The fault code indicates whether the inputs of the function are within their valid range.
Fault Logic
Condition Hex
An input is too
high
*
Bit 16 set to 1 identifies a standard Danfoss status or fault code.
*
Binary Cause Response Correction
0x8002 0010 Red > 10000, Green > 10000, Blue > 10000,
White > 10000
Status Code, Transmission is
disabled
Fault Code, Transmission is
disabled
Correct Dest_Addr or Src_Addr
value.
Correct Red, Green,Blue, or
White value.
6 | © Danfoss | April 2019 AQ299264497162en-000101
User Manual
Plus+1 Compliant® HMK_Brightness Function Block
©
Danfoss | April 2019 AQ299264497162en-000101 | 7
User Manual
Plus+1 Compliant® HMK_Brightness Function Block
8 | © Danfoss | April 2019 AQ299264497162en-000101
User Manual
Plus+1 Compliant® HMK_Brightness Function Block
©
Danfoss | April 2019 AQ299264497162en-000101 | 9
Danfoss
Power Solutions GmbH & Co. OHG
Krokamp 35
D-24539 Neumünster, Germany
Phone: +49 4321 871 0
Danfoss
Power Solutions ApS
Nordborgvej 81
DK-6430 Nordborg, Denmark
Phone: +45 7488 2222
Danfoss
Power Solutions (US) Company
2800 East 13th Street
Ames, IA 50010, USA
Phone: +1 515 239 6000
Danfoss
Power Solutions Trading
(Shanghai) Co., Ltd.
Building #22, No. 1000 Jin Hai Rd
Jin Qiao, Pudong New District
Shanghai, China 201206
Phone: +86 21 3418 5200
Products we offer:
Comatrol
www.comatrol.com
Turolla
www.turollaocg.com
Hydro-Gear
www.hydro-gear.com
Daikin-Sauer-Danfoss
www.daikin-sauer-danfoss.com
DCV directional control
•
valves
Electric converters
•
Electric machines
•
Electric motors
•
Hydrostatic motors
•
Hydrostatic pumps
•
Orbital motors
•
PLUS+1® controllers
•
PLUS+1® displays
•
PLUS+1® joysticks and
•
pedals
PLUS+1® operator
•
interfaces
PLUS+1® sensors
•
PLUS+1® software
•
PLUS+1® software services,
•
support and training
Position controls and
•
sensors
PVG proportional valves
•
Steering components and
•
systems
Telematics
•
Danfoss Power Solutions is a global manufacturer and supplier of high-quality hydraulic and
electric components. We specialize in providing state-of-the-art technology and solutions
that excel in the harsh operating conditions of the mobile off-highway market as well as the
marine sector. Building on our extensive applications expertise, we work closely with you to
ensure exceptional performance for a broad range of applications. We help you and other
customers around the world speed up system development, reduce costs and bring vehicles
and vessels to market faster.
Danfoss Power Solutions – your strongest partner in mobile hydraulics and mobile
electrification.
Go to www.danfoss.com for further product information.
We offer you expert worldwide support for ensuring the best possible solutions for
outstanding performance. And with an extensive network of Global Service Partners, we also
provide you with comprehensive global service for all of our components.
Local address:
Danfoss can accept no responsibility for possible errors in catalogues, brochures and other printed material. Danfoss reserves the right to alter its products without notice. This also applies to products
already on order provided that such alterations can be made without subsequent changes being necessary in specifications already agreed.
All trademarks in this material are property of the respective companies. Danfoss and the Danfoss logotype are trademarks of Danfoss A/S. All rights reserved.
©
Danfoss | April 2019 AQ299264497162en-000101
Loading...