Danfoss EDA-24, EDA-230 Data sheet

Data Sheet
Dew-Point Alarm Types EDA-24 and EDA-230
Application
EDA Dew-point Alarm
EDA is an electronic dew-point alarm for monitoring chilled panels or chilled beams.
EDA can be used in connection with Danfoss self­actuating climatic regulator FED/FEK.
Via sensor type EDA-S, the electronic dew-point alarm EDA registers whether condensate is appearing on the flow pipe to the chilled panel/ chilled beam.
When condensate is registered on the flow pipe to the chilled panel/chilled beam, the electronic dew-point alarm EDA is activated. In the alarm
mode, the two potential-free relay outputs are activated. The relay outputs can be used to shut off the chilling valve for the chilled panel/chilled beam and to give a signal to a alarm system or BMS system that condensate has generated in this regulation zone. The relay outputs are in the alarm mode in the case of condensate, short­circuited sensor circuit or disconnected sensor circuit.
EDA has a potentiometer for setting the sensitivity of the EDA-S sensor. The EDA-S sensor is placed on the flow pipe for the chilled panel/beam, following which condensate on the EDA-S sensor will trigger an alarm. The sensor is attached by means of plastic strips supplied with the EDA-S sensor.
LED indication:
On the front of the electronic dew-point alarm, EDA, there are two LEDs:
Green LED to show whether a supply
voltage has been connected to the product. Red LED to show whether there is a dew-
point or sensor alarm.
Ordering and Specifications
Danfoss Heating Solutions VD36A302 © Danfoss 02/2011 1
Electronic dew-point alarm
Type Description Code no. EDA-24 Electronic dew-point alarm, 24 V power supply 088H3001 EDA-230 Electronic dew-point alarm, 230 V power supply 088H3002 EDA-S Sensor for electronic dew-point alarm 088H3011
Accessories
Description Code no. Plastic box for EDA, enclosure IP54, dimensions, mm: H = 130, D = 94, W = 94 088H3010
Valve
Type Description Code no. RA-C 15 For chilling and heating circuits 013G3094 RA-C 20 For chilling and heating circuits 013G3096
Thermal actuator
All Danfoss thermal actuators, type TWA, can be used with the EDA dew-point alarm. Further information is available from the TWA data sheets.
Data Sheet Dew-Point Alarm Types EDA-24 and EDA-230
Wiring Diagram
Data
To sensor
Power supply
Type EDA-24 EDA-230 Supply voltage 24 VAC± 10%, 50-60 Hz 230 VAC ± 10%, 50-60 Hz Power consumption 3 VA 3 VA Relay output 1* (7-5 / 7-6) 230 VAC, 10 A, NO/NC 230 VAC, 10 A, NO/NC Relay output 2* (13-14) 24 VAC, 2 A, NC 24 VAC, 2 A, NC Ambient temperature -20 /+50 °C -20 /+50 °C
Dimensions
*Stated with connected supply voltage, but condensate alarm not in alarm mode.
2 VD36A302 © Danfoss 02/2011 Danfoss Heating Solutions
1
2
3
4
5
6
7
4
Data Sheet Dew-Point Alarm Types EDA-24 and EDA-230
Electrical Connection, Self­Actuating Climatic Regulator FED-IF
1. FED-IF
2. TWA-A (NC) *
3. Moisture sensor EDA-S
4. RA-C
5. RA-N
6. Alarm to BMS, if applicable
7. AVDO
Danfoss Heating Solutions VD36A302 © Danfoss 02/2011 3
Data Sheet Dew-Point Alarm Types EDA-24 and EDA-230
Danfoss A/S Heating Solutions Haarupvaenget 11 8600 Silkeborg Denmark Phone:+45 7488 8000 Fax: +45 7488 8100 Email: heating.solutions@danfoss.com www.heating.danfoss.com
Danfoss can accept no responsibility for possible errors in catalogues, brochures and other printed material. Danfoss reserves the right to alter its products without notice. This also applies to products already on order provided that such alterations can be made without subsequential changes being necessary in specifications already agreed. All trademarks in this material are property of the respective companies. Danfoss and the Danfoss logotype are trademarks of Danfoss A/S. All rights reserved.
4 VD36A302 © Danfoss 02/2011 Danfoss Heating Solutions
Loading...