Installation guide
ELIMINATOR® Hermetic receiver filter drier
Type DMC and DCC
<![if ! IE]> <![endif]>023R9534 |
Refrigerants: |
Temperature range: |
Max. working pressure: |
||||||
|
|
||||||||
|
|
R134a, R404A, R407C, R507, R22, R410A. |
|
|
|
|
-40 |
– 70 °C |
PS / MWP = 42 bar / 610 psig |
|
|
|
|
||||||
|
|
For other refrigerants, please |
|
|
|
|
-40 |
– 160 °F |
|
|
|
contact Danfoss representative. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Installation |
Soldering |
|
<![if ! IE]> <![endif]>Danfoss 23Z9037 |
Min.5% Ag
DMC / DCC |
<![if ! IE]> <![endif]>Danfoss 23Z7016.10 |
<![if ! IE]> <![endif]>Danfoss 23Z7016.10 |
|
|
After charging, mark the system with the refrigerant and the oil used.
Mounting
Preferred position |
Wrong position |
Customer best practice will still be needed: |
|
• Use wet wrap when installing. |
|||
|
|
||
|
|
• Braze the joints. |
|
|
|
• Let them cool down. |
|
|
|
• Clean the brazing /welding area after the installa- |
|
|
|
tion (remove remaining flux with a brush). |
|
|
|
• This is an important operation and needs to be |
|
|
|
done with great care to remove all remaining flux. |
|
|
|
• Paint / Anti-corrosive needs to cover all open steel |
|
|
|
parts, areas where the black original paint has been |
|
|
|
burnt due to brazing and at least 3 cm approx of the |
|
|
|
copper. |
|
|
|
• Paint the joints twice. |
<![endif]>023R9534
© Danfoss | Climate Solutions | 2021.09 |
AN142486435087en-000301 | 1 |