Danfoss DLE7.5CN Data sheet

Datasheets

DLE7.5CN Energy-optimized LBP/MBP Compressor

R290, 220-240V 50Hz

General

Code number						102H4853
Approvals			EN 60335-2-34 w. Annex AA
Compressors on pallet						100
Application
Application						LBP/MBP
Frequency		Hz		50					60
Evaporating temperature		°C	-35 to 7.2						–
Voltage range		V	198 to 254						–
Max. condensing temperature continuous (short)		°C		55 (65)					–
Max. winding temperature continuous (short)		°C	125 (135)						–
Cooling requirements
Frequency		Hz		50					60
Application			LBP		MBP	HBP		LBP	MBP		HBP
32°C			F2		F2	–		–	–		–
38°C			F2		F2	–		–	–		–
43°C			F2		F2	–		–	–		–
Remarks on application:
For evaporation temperatures higher than 0 °C do not run compressor at condensing
temperatures higher 50 °C in steady state operation.
Motor
Motor type					CSIR/RSIR/RSCR
LRA (rated after 4 sec. UL984), HST | LST		A		9.3					9.2
Cut in Current, HST | LST		A		9.3					14.5
Resistance, main | start winding (25°C)		Ω		10.9					8.3
Design
Displacement		cm3				7.48
Oil quantity (type)		cm3			230 (polyolester)
Maximum refrigerant charge		g				150
Free gas volume in compressor		cm3				1465
Weight without electrical equipment		kg				8.0
Dimensions
Height		mm	A			175
			B			169
			B1				–
			B2				–
Suction connector	location/I.D. mm | angle		C			8.2 | 18°
	material | comment				Copper | Rubber plug
Process connector	location/I.D. mm | angle		D			6.2 | 61°
	material | comment				Copper | Rubber plug
Discharge connector	location/I.D. mm | angle		E			6.2 | 25°
	material | comment				Copper | Rubber plug
Oil cooler connector	location/I.D. mm | angle		F				–
	material | comment						–
Connector tolerance	I.D. mm					±0.09
Remarks:

This product is approved for

R290 regarding explosion safety according to standard EN 60335-1 and EN 60335-

2-34

S	= Static cooling normally sufficient
O	= Oil cooling
F1	= Fan cooling 1.5 m/s
	(compressor compartment temperature
	equal to ambient temperature)
F2	= Fan cooling 3.0 m/s necessary
SG	= Suction gas cooling normally sufficent

–= not applicable in this area

© Danfoss | DCS (CC) | 2017.02

DEHC.ED.200.A3.02 | 1

EN 12900 LBP								220V, 50Hz, CSIR/RSIR, fan cooling F2
Evap. temp. in °C				-45	-40	-35		-30		-25		-23.3	-20	-15					-10	-6.7			-5		0		5		7.2	10				15	20
Capacity in W						212		268		336		362	417	512					623	706			752		900		1070		1151
Power cons. in W						187		206		226		233	247	267					288	302			309		331		353		363
Current cons. in A						1.40		1.45		1.50		1.52	1.55	1.62					1.68	1.73			1.76		1.83		1.91		1.95
COP in W/W						1.13		1.30		1.49		1.55	1.69	1.92					2.16	2.34			2.43		2.72		3.03		3.17
EN 12900 MBP								220V, 50Hz, CSIR/RSIR, fan cooling F2
Evap. temp. in °C				-45	-40	-35		-30		-25		-23.3	-20	-15					-10	-6.7			-5		0		5		7.2	10				15	20
Capacity in W						198		251		315		339	390	479					583	660			703		841		1000		1076
Power cons. in W						193		214		236		243	258	280					302	317			325		349		373		383
Current cons. in A						1.41		1.46		1.52		1.54	1.58	1.65					1.73	1.78			1.81		1.89		1.98		2.02
COP in W/W						1.03		1.17		1.33		1.39	1.51	1.71					1.93	2.08			2.16		2.41		2.68		2.81
ASHRAE LBP								220V, 50Hz, CSIR/RSIR, fan cooling F2
Evap. temp. in °C				-45	-40	-35		-30		-25		-23.3	-20	-15					-10	-6.7			-5		0		5		7.2	10				15	20
Capacity in W						209		269		339		366	422	519					633	718			765		918		1094		1179
Power cons. in W						188		214		240		249	266	292					319	336			345		372		399		411
Current cons. in A						1.41		1.48		1.56		1.59	1.65	1.74					1.84	1.91			1.95		2.06		2.18		2.23
COP in W/W						1.11		1.26		1.41		1.47	1.59	1.78					1.99	2.14			2.22		2.47		2.74		2.87
ASHRAE MBP/HBP								220V, 50Hz, CSIR/RSIR, fan cooling F2
Evap. temp. in °C				-45	-40	-35		-30		-25		-23.3	-20	-15					-10	-6.7			-5		0		5		7.2	10				15	20
Capacity in W						187		240		303		327	377	463					564	640			682		817		973		1048
Power cons. in W						186		212		237		246	263	289					315	332			341		368		394		406
Current cons. in A						1.41		1.48		1.56		1.59	1.65	1.74					1.84	1.91			1.95		2.06		2.18		2.23
COP in W/W						1.00		1.14		1.28		1.33	1.43	1.60					1.79	1.93			2.00		2.22		2.47		2.58

	Accessories for	DLE7.5CN	Figure	Code number
	PTC starting device	6.3 mm spade connectors		–
		4.8 mm spade connectors	a1	–
	ePTC starting device	4.8 mm spade connectors		103N0050
	Starting relay	6.3 mm spade connectors	a2	117U7002
	Start. capacitor 80 µF	6.3 mm spade connectors	c	117U5015
	Cover		b	103N0491
	Run capacitor 5 µF	6.3 mm spade connectors	e	–
	(optional)	4.8 mm spade connectors		117-7129
	Cord relief		d	103N1010
	Protection screen for PTC		g	–

Test conditions	EN 12900		ASHRAE
	LBP	MBP	LBP	MBP
Condensing temperature	40°C	45°C	54.4°C	54.4°C
Ambient temperature	32°C	32°C	32.2°C	35°C
Suction gas temperature	20°C	20°C	32.2°C	35°C
Liquid temperature	no subcooling		32.2°C	46.1°C

Mounting accessories			Code number
Bolt joint for one comp.	Ø: 16	mm	118-1917
Bolt joint in quantities	Ø: 16	mm	118-1918
Snap-on in quantities	Ø: 16	mm	118-1919

Danfoss can accept no responsibility for possible errors in catalogues, brochures and other printed material. Danfoss reserves the right to alter its products without notice.This also applies to products already on order provided that such alterations can be made without subsequential changes being necessary eady agreed.

All trademarks in this material are property of the respective companies. Danfoss and the Danfoss logotype are trademarks of Danfoss A/S. All rights reserved.

2 |© Danfoss | DCS (CC) | 2017.02

DEHC.ED.200.A3.02