Danfoss DLE5.7CN Data sheet
Datasheets
DLE5.7CN
Energy-optimized LBP/MBP Compressor
R290, 220-240V 50Hz
General
Code number 102H4653
Approvals EN 60335-2-34 w. Annex AA
Compressors on pallet 100
Application
Application LBP/MBP
Frequency Hz 50 60
Evaporating temperature °C -35 to 7.2 –
Voltage range V 198 to 254 –
Max. condensing temperature continuous (short) °C 55 (65) –
Max. winding temperature continuous (short) °C 125 (135) –
Cooling requirements
Frequency Hz 50 60
Application
32°C F2F2– – – –
38°C F2F2– – – –
43°C F2F2– – – –
Remarks on application:
For evaporation temperatures higher than 0 °C do not run compressor at condensing
temperatures higher 50 °C in steady state operation.
Motor
Motor type CSIR/RSIR/RSCR
LRA (rated after 4 sec. UL984), HST | LST A 8.8 7.4
Cut in Current, HST | LST A 8.8 11.9
Resistance, main | start winding (25°C) Ω 13.5 14.3
LBP MBP HBP LBP MBP HBP
This product is approved for
R290 regarding explosion
safety according to standard
EN 60335-1 and EN 603352-34
S =Staticcoolingnormallysufcient
O = Oil cooling
F1 = Fan cooling 1.5 m/s
(compressor compartment temperature
equal to ambient temperature)
F2 = Fan cooling 3.0 m/s necessary
SG =Suctiongascoolingnormallysufcent
– = not applicable in this area
Design
Displacement cm
Oil quantity (type) cm
Maximum refrigerant charge g 150
Free gas volume in compressor cm
Weight without electrical equipment kg 8.0
Dimensions
Height mm A 175
Suction connector location/I.D. mm | angle C 8.2 | 18°
material | comment Copper | Rubber plug
Process connector location/I.D. mm | angle D 6.2 | 61°
material | comment Copper | Rubber plug
Discharge connector location/I.D. mm | angle E 6.2 | 25°
material | comment Copper | Rubber plug
Oil cooler connector location/I.D. mm | angle F –
material | comment –
Connector tolerance I.D. mm ±0.09
Remarks:
3
3
3
230 (polyolester)
B 169
B1 –
B2 –
5.70
1465
© Danfoss | DCS (CC) | 2017.02
DEHC.ED.100.B9.02 | 1
EN 12900 LBP 220V, 50Hz, CSIR/RSIR, fan cooling F
Danf
already on order pro
All trademarks in this material are property of the respec
2
Evap. temp. in °C -45 -40 -35 -30 -25 -23.3 -20 -15 -10 -6.7 -5 0 5 7.2 10 15 20
Capacity in W 169 215 267 287 328 400 483 547 582 697 832 897
Power cons. in W 145 162 179 184 194 208 222 230 234 245 256 260
Current cons. in A 1.13 1.17 1.21 1.23 1.25 1.30 1.34 1.36 1.38 1.42 1.45 1.47
COP in W/W 1.17 1.33 1.50 1.56 1.69 1.92 2.18 2.38 2.49 2.84 3.25 3.45
EN 12900 MBP 220V, 50Hz, CSIR/RSIR, fan cooling F
2
Evap. temp. in °C -45 -40 -35 -30 -25 -23.3 -20 -15 -10 -6.7 -5 0 5 7.2 10 15 20
Capacity in W 158 203 252 271 309 376 454 513 546 654 780 841
Power cons. in W 148 167 184 190 201 218 233 243 248 262 276 281
Current cons. in A 1.13 1.18 1.23 1.24 1.27 1.32 1.37 1.40 1.42 1.47 1.52 1.54
COP in W/W 1.07 1.22 1.37 1.42 1.54 1.73 1.95 2.11 2.20 2.49 2.83 2.99
ASHRAE LBP 220V, 50Hz, CSIR/RSIR, fan cooling F
2
Evap. temp. in °C -45 -40 -35 -30 -25 -23.3 -20 -15 -10 -6.7 -5 0 5 7.2 10 15 20
Capacity in W 168 220 277 298 341 415 501 566 603 722 862 930
Power cons. in W 149 169 188 195 208 227 245 258 264 282 300 308
Current cons. in A 1.15 1.20 1.26 1.28 1.32 1.38 1.45 1.50 1.52 1.59 1.67 1.70
COP in W/W 1.12 1.30 1.47 1.53 1.64 1.83 2.04 2.20 2.28 2.56 2.87 3.03
ASHRAE MBP/HBP 220V, 50Hz, CSIR/RSIR, fan cooling F
2
Evap. temp. in °C -45 -40 -35 -30 -25 -23.3 -20 -15 -10 -6.7 -5 0 5 7.2 10 15 20
Capacity in W 150 197 247 266 304 370 447 505 537 643 766 827
Power cons. in W 148 167 186 193 205 224 243 255 261 279 296 304
Current cons. in A 1.15 1.20 1.26 1.28 1.32 1.38 1.45 1.50 1.52 1.59 1.67 1.70
COP in W/W 1.02 1.18 1.33 1.38 1.48 1.65 1.84 1.98 2.06 2.31 2.59 2.72
Accessories for DLE5.7CN Figure Code number Test conditions
EN 12900
LBP MBP
PTC starting device 6.3 mm spade connectors
4.8 mm spade connectors – Ambient temperature 32°C 32°C 32.2°C 35°C
a1
– Condensing temperature 40°C 45°C 54.4°C 54.4°C
ePTC starting device 4.8 mm spade connectors 103N0050 Suction gas temperature 20°C 20°C 32.2°C 35°C
Starting relay 6.3 mm spade connectors a2 117U7015 Liquid temperature no subcooling 32.2°C 46.1°C
Start. capacitor 80 µF 6.3 mm spade connectors c 117U5015
Cover b 103N0491 Mounting accessories Code number
Run capacitor 5 µF 6.3 mm spade connectors
(optional) 4.8 mm spade connectors 117-7129 Bolt joint in quantities Ø: 16 mm 118-1918
e
– Bolt joint for one comp. Ø: 16 mm 118-1917
Cord relief d 103N1010 Snap-on in quantities Ø: 16 mm 118-1919
Protection screen for PTC g –
oss can accept no responsibility for possible errors in catalogues, brochures and other printed material. Danfoss reserves the right to alter its products without notice. This also applies to products
vided that such alterations can be made without subsequential changes being necessary eady agreed.
tive companies. Danfoss and the Danfoss logotype are trademarks of Danfoss A/S. All rights reserved.
2 |© Danfoss | DCS (CC) | 2017.02 DEHC.ED.100.B9.02
ASHRAE
LBP MBP
Loading...