Danfoss D14E, M19P, R16, R13 Data sheet
Data Sheet
Robust Coils
D14E, M19P, R16, R13
Danfoss robust coils are specifically designed for
harsh operating environments. Compared to standard
coils, they have higher tolerances to temperature
extremes, voltage spikes, and water ingression due to
power spray, or immersion in water, snow or mud.
Typical applications include asphalt machinery,
agricultural equipment with chemical and power
wash exposure, snow plows and salt-spreader
machines, or any application when applying the
valves in a hot engine compartment.
Featuring a very compact design, robust coils are
smaller than several competing manufacturer’s coils,
providing more space for other components on the
application. In addition, the smaller footprint makes it
possible to fit more cartridge valves closer together in
the vehicle HIC (Hydraulic Integrated Circuit).
Features
•
Four frame sizes - R13, R16, M19P &
D14E - providing a Robust Coil option
for over 75% of our Solenoid and
Proportional Cartridge Valves
•
All Robust Coils meet our major OEMS’s
most stringent requirements for offhighway vehicles
•
No O-ring seal is required around coils
•
IP69K Environmental Rating for majority
of connector options
DEUTSCH, Amp SuperSeal, Metri-
‒
Pack 150 Type 2 and Lead Wires
•
PLUS+1® Compliant
All coils are designed for installation
‒
on machines that utilize Danfoss
Power Solutions PLUS+1® hardware,
ensuring they are compliant out of
the box.
R13 and R16
•
Robust option for Danfoss Solenoid
Valves and some Proportional Valves
•
Available for 08, 09 and 10 size solenoid
or proportional valves
•
Available for SVP12, SVP16, and SVP20
solenoid valves
•
4 different DC voltages: 10, 12, 20, 24
VDC (color coded for easy voltage
identification)
•
Directly interchangeable with the
Standard Coils M13 and M16
Can field retrofit from Standard to
‒
Robust (ensure there is enough
spacing between valves)
Change to metal nut and remove O-
‒
rings
•
Available with bi-directional diodes
Protects system's electronics against
‒
voltage spikes from the coil
Non-polarity dependent, simple
‒
installation
•
Compact design
R16: Manifold length reduced by 7
‒
mm (0.28 in) per valve compared to
other manufacturer's coils when
valves are side by side
•
Available on the PSV10-34 proportional
directional valves and PPR09-POD
proportional pressure reducing valve
M19P and D14E
•
Standard Robust Coils for Danfoss
Proportional Valves
•
Proportional Flow Control, Proportional
Pressure Relieving and Proportional
Pressure Reducing Valves
•
IP69K Environmental Rating for
DEUTSCH connector
When the R13 and R16 Robust Coils were
designed and tested, the existing M19P
and D14E coils were also tested and passed
the Robust Coil extreme test requirements.
Comprehensive technical literature is
online at www.danfoss.com
©
Danfoss | September 2020 AI354779886259en-000101 | 1
Data Sheet
Robust Coils D14E, M19P, R16, R13
Technical Overview (R13 and R16 only)
Highlighted features
Number Feature Description
1 Fully encapsulated
windings
2 Bi-directional diodes The bi-directional TVS diode is not
3 Protective metal
casing
The coil is designed with a
protective layer of encapsulated
plastic. A special molding
technique prevents moisture buildup while the plastic is applied.
polarity dependent and therefore
does not require the alignment of
the coil terminals during
installation, which will reduce the
risks in electrical installations.
The metal exterior casing protects
against dramatic temperature
changes and physical damage to
the coil. Robust coils have passed
the drop test, vibration test, and
the mechanical shock test.
Additional features
Feature Description
Water ingression protection Robust coils are designed to be
highly water and chemical
resistant. They have passed
comprehensive tests for salt, fog,
chemical splash and humidity.
Interchangeable with Standard
M13 and M16
No O-rings needed For ease of installation, robust coils
IP69K with integral connectors Robust coils with DEUTSCH, AMP
High input voltage tolerance Robust coils are rated for 75% to
Can field retrofit from standard to
robust, providing there is adequate
space between the valves on the
manifold. Add the metal nut and
remove the O-rings.
do not need coil O-rings.
SuperSeal, Lead Wires and MetriPack 150 Type 2 are
environmentally rated IP69K.
133% of nominal (see graphs
below).
R13 voltage tolerance
R16 voltage tolerance
2 | © Danfoss | September 2020 AI354779886259en-000101
Loading...