How it Works
Danfoss
Loading...
C
Loading...
Loading...
Colibri ETS 50C
Installation Manual
6 pgs1.84 Mb0

Danfoss Colibri ETS 12C, Colibri ETS 24C, Colibri ETS 50C, Colibri ETS 100C, Colibri ETS 25C Installation Manual

...
Download
ENGINEERING
TOMORROW
Installation guide
Colibri® Electric Expansion Valves
Type ETS 12C, ETS 24C, ETS 25C, ETS 50C, ETS 100C Colibri® Electric Regulating Valves
Type KVS 2C, KVS 3C KVS 5C
034R9806
© Danfoss | DCS (sw) | 2018.01
DKRCC.PI.VD1.F6.ML | 1
Danfoss R64-3051.10
Danf
oss
R
64-3051.1
0
Place the valve close to the evaporator.
It is recommended to use Danfoss filter drier before the expansion valve or a strainer for particles of 150 micron or smaller.
Application ETS Colibri®
Flow direction
Allowable ambient temperature:
Min. -40 °C / -40 °F Max. 70 °C / 158 °F
Max. working pressure:
50 bar(g) / 725 psi(g)
Refrigerants : R410A, R404A, R507, R134a, R407A, R407B, R407C, R407F, R32, R290, R1234ze, R1234yf, R449A, R449B, R452A, R1270, R600, R600a, R22, R23, R227, R417A, R444B, R447A, R448A, R454B, R422A, R422D, R427A, R502, R513A, R413A, R438A, R450A, R455B, R454C, R454A, R452B and *L40
*R-number allocation by ASHRAE is pending
Fluid temperature:
Min. -40 °C / -40 °F Max. 70 °C / 158 °F
Total steps:
600 full steps
Phase current:
800 mA peak / 600 mA RMS
Coil resistance:
10 Ω (20 °C / 68 °F)
Stepper motor type:
Bipolar
Do not connect directly to AC/DC power source. Connect valve to appropriate controller/driver only.
ETS / KVS Colibri® valves are delivered in open position, ready for brazing. An AST –g service driver is available for manual operation / service of ETS / KVS Colibri® valves.
English
Bi-flow
Reverse flow
Normal flow (Using sight glass for flash gas detection - ETS 25C to ETS 100C) KVS Colibri® valves have no sight glass integrated
Danfoss 34G231.10
Application KVS Colibri®
ETS Colibri®
KVS Colibri®
NormalReverse
GREEN: DRY
YELLOW: WET
Danfoss
34G136.12
MADE IN DENMARK
ETS XXXC
10 Ω, 800mA peak
N0311A
Colibri® Electric Expansion valve
-40/+70°C / -40/+158°F
PS 50bar / MWP 735psig
034GXXXX
NormalReverse
Danfoss
34G156.12
MADE IN DENMARK
ETS XXXC
10 Ω, 800mA peak
N0311A
Colibri® Electric Expansion valve
-40/+70°C / -40/+158°F
PS 50bar / MWP 735psig
034GXXXX
© Danfoss | DCS (sw) | 2018.01
DKRCC.PI.VD1.F6.ML | 2
Danfoss 34G58.15
2
1
oss
B1
B2
A1
A2
Danfoss
34G152.10
1
2
Danfoss
34G153.11
MADE IN DENMARK
ETS XXXC
10 Ω, 800mA peak
N0311A
Colibri® Electric Expansion valve
-40/+70°C / -40/+158°F
PS 50bar / MWP 735psig
034GXXXX
Danfoss
34G60..16
+90°
-90°
Danfoss
34G59.11
Brazing
Motor coil resistance check.
Coil A = Coil B = 10 Ω (20 °C / 68 °F)
Min. 5 % Ag
Mounting
N2 gas from opposite site of soldering point.
Max. 30 sec.
Max. 15 sec.
M12 Connection
N
2
Max. 150 °C
Installation video
Recommended:
Connector Nozzle size
1
/2 inch 2 mm 1/16 inch
5
/8 inch
7
/8 inch 1 1/8 inch 1 3/8 inch 1 5/8 inch 9 mm 3/8 inch
ENGINEERING
TOMORROW
Installation guide
Colibri® Electric Expansion Valves
Type ETS 12C, ETS 24C, ETS 25C, ETS 50C, ETS 100C Colibri® Electric Regulating Valves
Type KVS 2C, KVS 3C KVS 5C
034R9806
© Danfoss | DCS (sw) | 2018.01
DKRCC.PI.VD1.F6.ML | 3
NormalReverse
GREEN: DRY
YELLOW: WET
Danfoss
34G136.12
MADE IN DENMARK
ETS XXXC
10 Ω, 800mA peak
N0311A
Colibri® Electric Expansion valve
-40/+70°C / -40/+158°F
PS 50bar / MWP 735psig
034GXXXX
NormalReverse
Danfoss
34G156.12
MADE IN DENMARK
ETS XXXC
10 Ω, 800mA peak
N0311A
Colibri® Electric Expansion valve
-40/+70°C / -40/+158°F
PS 50bar / MWP 735psig
034GXXXX
Danfoss R64-3051.10
Danf
oss
R
64-3051.1
0
Es wird empfohlen Filtertrockner von Danfoss vor dem Expansionsventil oder einen Filter für Partikel von 150 µm oder kleiner zu verwenden. Il est recommandé d’utiliser un filtre déshydrateur Danfoss avant la vanne de détente, ou un filtre à particules de 150 microns ou moins.
ETS Colibri®
Ne pas raccorder directement le moteur à une alimentation AC / DC. Raccorder la vanne au régulateur approprié.
Das Ventil direkt am Verdampfer montieren. Placez la vanne près de l’évaporateur.
Bi-flow / Bi-directionnel
Normaler Durchfluss (ETS 25C und ETS 100C mit Schauglas für Flashgas Erkennung) Sens normal (ETS 25C pour ETS 100C - à l’aide du voyant de détection de gaz flash) KVS Colibri® haben kein Schauglass Les détendeurs KVS Colibri® n’ont pas de voyant intégré
Umgekehrt Durchfluss / Direction inverse
Anwendung / Application ETS Colibri®
Durchflussrichtung / Sens d’écoulement
Umgebungstemperatur: Température ambiante:
Min. -40 °C, Max. 70 °C
Max. Betriebsdruck: Pression de service max.:
50 bar(g)
Kältemittel / Fluides: R410A, R404A, R507, R134a, R407A, R407B, R407C, R407F, R32, R290, R1234ze, R1234yf,
R449A, R449B, R452A, R1270, R600, R600a, R22, R23, R227, R417A, R444B, R447A, R448A, R454B, R422A, R422D, R427A, R502, R513A, R413A, R438A, R450A, R455B, R454C, R454A, R452B and *L40
*R-number allocation by ASHRAE is pending.
Kältemitteltemperatur: Température du fluide:
Min. -40 °C, Max. 70 °C
Max. Schritte: Nombre de pas total:
600 full steps
Stromaufnahme: Courant de phase:
800 mA Peak (600 mA RMS)
Widerstand, Spule: Résistance de la bobine:
10 Ω (20 °C)
Schrittmotortyp: Type de moteur pas à pas:
Bipolar
Bitte das ETS / KVS Colibri® nicht direkt mit einer Spannungsquelle verbinden. Schließen Sie das Ventil nur an geeignete Regler/ Steuergeräte an.
Ventile werden in offener Position geliefert, bereit zum Löten. Für den manuellen Betrieb / Wartung von ETS / KVS Colibri® Ventilen, ist ein AST -g-Servicemodul als
Zubehör erhältlich.
Les vannes sont livrées en position ouverte, prêtes pour le brasage. Un pilote d’entretien AST-g est disponible pour
manœuvrer les vannes ETS C / KVS Colibri®.
Deutsch, French
Danfoss 34G231.10
Anwendung / Application KVS Colibri®
KVS Colibri®
© Danfoss | DCS (sw) | 2018.01
DKRCC.PI.VD1.F6.ML | 4
Danfoss 34G58.15
2
1
oss
B1
B2
A1
A2
Danfoss
34G152.10
1
2
Danfoss
34G153.11
MADE IN DENMARK
ETS XXXC
10 Ω, 800mA peak
N0311A
Colibri® Electric Expansion valve
-40/+70°C / -40/+158°F
PS 50bar / MWP 735psig
034GXXXX
Danfoss
34G60..16
+90°
-90°
Danfoss
34G59.11
Löten / Soudure
Wicklungswiderstand prüfen. Vérification de la résistance de la bobine du moteur.
Wicklung A = Wicklung B = 10 Ω (20 °C)
Bobine A = Bobine B = 10 Ω (20 °C)
Min. 5 % Ag
Max. 150 °C
Einbaulage / Montage
Schutzgas gegenüber der Lötstelle einströmen lassen.
Refroidissement gaz ci-contre site de point de soudure.
Max. 30 sec.
Max. 15 sec.
M12 Connection /
M12 Raccordement
N
2
Installation Video
Installation vidéo
Empfehlung /
Recommendation
Anschluss Brennerdüse
Raccord Buse de brasage
1
/2 inch 2 mm 1/16 inch
5
/8 inch
7
/8 inch 1 1/8 inch 1 3/8 inch 1 5/8 inch 9 mm 3/8 inch
ENGINEERING
TOMORROW
Installation guide
Colibri® Electric Expansion Valves
Type ETS 12C, ETS 24C, ETS 25C, ETS 50C, ETS 100C Colibri® Electric Regulating Valves
Type KVS 2C, KVS 3C KVS 5C
034R9806
© Danfoss | DCS (sw) | 2018.01
DKRCC.PI.VD1.F6.ML | 5
Se recomienda utilizar un filtro deshidratador Danfoss antes de la válvula de expansión o un filtro para partículas de 150 micras o menores.
建议在膨胀阀前使用丹佛斯干燥过滤器或使用过滤目 数小于等于150 微 米的过 滤网
ETS Colibri®
请仅将阀门连接于合适的控制器/驱动器，勿直 接与交流或直流电源连接。
Colocar la válvula próxima al evaporador.
阀 关 闭 位 置 ，靠 近 蒸 发 器 侧
Bi-flow
双向流
Flujo normal (ETS 25C a ETS 100C incorpora un visor de líquido para detector flash-gas)
正常流动方向（视液镜，用于闪发气体检测–ETS 25C 和 ETS 100C）
Las válvulas KVS Colibri® no tienen visor integrado KVS Colibri® 电子膨胀阀没有集成观察镜
Flujo reversible
反向流动方向
Aplicación / 应用 ETS Colibri®
Dirección del flujo /
流向
Temperatura ambiente permisible:
允许运行的环境温度:
Min. -40 °C / Max. 70 °C
Presión de trabajo máx.:
最大工作压力:
50 bar(g)
Refrigerantes / 制冷剂适用:R410A, R404A, R507, R134a, R407A, R407B, R407C, R407F, R32, R290, R1234ze,
R1234yf, R449A, R449B, R452A, R1270, R600, R600a, R22, R23, R227, R417A, R444B, R447A, R448A, R454B, R422A, R422D, R427A, R502, R513A, R413A, R438A, R450A, R455B, R454C, R454A, R452B and *L40
*R-number allocation by ASHRAE is pending
Temperatura líquido:
流体 温 度:
Min. -40 °C / Max. 70 °C
Número de pasos total:
总步数:
600 full steps / 600 步
Intensidad:
相电流:
800 mA Pico/peak (600 mA RMS)
Resistencia:
电阻:
10 Ω (20 °C)
Tipo de motor a pasos:
步进电机形式:
Bipolar
双极
No aplicar tensión directamente a la válvula. Conectar la válvula a un controlador/driver adecuado.
Las válvulas se entregan abiertas listas para soldar. Existe un driver de servicio AST-g para la operación manual y servicio de las
válvulas ETS / KVS Colibrí®.
交付 时 阀 门 处 于 全 开状 态 ,再进 行 焊 接 一切就绪，准备铜焊. 提供AST -g手操器用于 ETS/KVS Colibri® 电子膨胀阀的手动操作和维修.
español,
汉语
Danfoss R64-3051.10
Danf
oss
R
64-3051.1
0
Danfoss 34G231.10
KVS Colibri®
Aplicación / 应用 KVS Colibri®
NormalReverse
GREEN: DRY
YELLOW: WET
Danfoss
34G136.12
MADE IN DENMARK
ETS XXXC
10 Ω, 800mA peak
N0311A
Colibri® Electric Expansion valve
-40/+70°C / -40/+158°F
PS 50bar / MWP 735psig
034GXXXX
NormalReverse
Danfoss
34G156.12
MADE IN DENMARK
ETS XXXC
10 Ω, 800mA peak
N0311A
Colibri® Electric Expansion valve
-40/+70°C / -40/+158°F
PS 50bar / MWP 735psig
034GXXXX
© Danfoss | DCS (sw) | 2018.01
DKRCC.PI.VD1.F6.ML | 6
Danfoss 34G58.15
2
1
oss
B1
B2
A1
A2
Danfoss
34G152.10
1
2
Danfoss
34G153.11
MADE IN DENMARK
ETS XXXC
10 Ω, 800mA peak
N0311A
Colibri® Electric Expansion valve
-40/+70°C / -40/+158°F
PS 50bar / MWP 735psig
034GXXXX
Danfoss
34G60..16
+90°
-90°
Danfoss
34G59.11
Soldadura / 焊接
Verificar la resistencia de la bobina del motor.
Bobina A = Bobina B = 10 Ω (20 °C)
电机线圈电阻检查 在20℃时，线圈A=线圈B=10Ω
Min. 5 % Ag
Max. 150 °C
Instalación / 安装
Corriente de N2 desde el lado opuesto a la soldadura.
气体冷 却对面的焊点（氮气保 护）
Max. 30 sec.
Max. 15 sec.
M12 Conexión / M12 链接
N
2
Instalación vídeo
安裝 視頻
Recomendación/
推荐
Conexión Boquilla soplete 连接 钎焊嘴
1
/2 inch 2 mm 1/16 inch
5
/8 inch
7
/8 inch 1 1/8 inch 1 3/8 inch 1 5/8 inch 9 mm 3/8 inch
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use