Danfoss Atomizing Water Spray Nozzles Types M Data sheet
Data sheet
√
Atomizing Water Spray Nozzles Types M & MW
Application
Mini nozzle type M features our unique perfect
solution where small size, accurate ow rates,
very ne atomization and low cost are desired.
Mini Wide nozzle type MW designates “wide
angle” and provides a very ne atomization in low
volume ow rates with a wide spray angle and
large coverage area.
Identification The nozzles are marked with the following
information:
MW 5
12345
Hago Mini nozzles are widely used in both
professional and home green houses for plant
and seedling misting, in industry for process
cooling or humidifying and in agriculture for
livestock cooling. In recent years they have been
used in dry climates for home patio cooling.
Application and Features
• Misting, cooling, humidifying
• Spraying light oils
Availability
• M: 80° spray angle at 100psi (~ 7 bar) water
• MW: 160° spray angle at 100psi (~ 7 bar) water
• Spray pattern: Semi solid cone
• Available in a 12 piece box single packed or a
50 piece blister pack.
Technical Data
Stampe d on the flats
MW Spray Angle MW = Mini Wide
5 5 = 5 USgal/h at 100 psi (~ 7 bar)
Batch code for internal use
Material and construction
Brass: Our common grade material of
construction. Acceptable for most water based
applications.
Stainless Steel (Type 416): Shows good resistance
to wear at higher water pressures. It is rust
resistant as well, but not rust proof.
Pressure vs. Flow
For general purposes, changes in flow rate due
to changes in pressure can be estimated as being
approximately equal to the square root of the
pressure ratio.
Therefore: Flow rate at the desired pressure =
Filtration
120 μm stainless steel filter.
Recommended tightening torque
100-150 in-lbs (11-17 Nm).
Maximum tightening torque
150 in-lbs (17 Nm).
© Danfoss | 03/2018 VDDZF222 | 1
Danf
already on order pro
All trademarks in this material are property of the respec
Data sheet Atomizing Water Spray Nozzles Types M & MW
DB
80°
Design
Dimensions
A: Tip
B: Disc
C: Filter
D: Spring
Spray angles
160°
C
A
Dimensions for reference only.
Program
Danfoss
Mini
M1 030L4604 030L4654 030L4606 030L4656 1.00
M2 030L4608 030L4658 030L4609 030L4659 2.00
M3 030 L4610 030L4660 03 0L 4611 030L4661 3.00
M4 030 L4612 030L4662 03 0L4613 030L4663 4.00
M5 030 L4614 030L4664 03 0L4615 030L4665 5.0 0
M7 - - 030 L4619 030L4669 7. 00
M10 03 0L4616 030L4666 - - 10.0 0
M15 0 30L 4617 030L4667 030L4 618 030L4668 15.00
Mini-Wide
MW5 030L4602 030 L4652 030 L4601 030 L4651 5.00
MW 11 - - 030L4 621 030 L4671 11.0 0
MW15 030L4603 030L 4653 - - 15. 00
Brass
12 p iec es
Brass
12 p iec es
Brass
50 pieces
Brass
50 pieces
Steel
12 p iec es
Steel
12 p iec es
Steel
50 pieces
Steel
50 pieces
at 100 psi
at 100 psi
Toronto, ON/Baltimore, MD
Toll Free: 888-DANFOSS (326-3677) Option #3 for Heating
heating.danfoss.us
heating.cs.na@danfoss.com
oss can accept no responsibility for possible errors in catalogues, brochures and other printed material. Danfoss reserves the right to alter its products without notice. This also applies to products
vided that such alterations can be made without subsequential changes being necessary eady agreed.
tive companies. Danfoss and the Danfoss logotype are trademarks of Danfoss A/S. All rights reserved.
Usgal/h
Usgal/h
© Danfoss | DHS-SRMT/SI | 03/20182 | VDDZF222
Loading...