Drawings & Flow Charts ................................................................ v
ivTable of Contents
SiBE04-401Introduction
1. Introduction
1.1Safety Cautions
Cautions and
Warnings
Be sure to read the following safety cautions before conducting repair work.
The caution items are classified into “Warning” and “Caution”. The “Warning”
items are especially important since they can lead to death or serious injury if they are not
followed closely. The “Caution” items can also lead to serious accidents under some
conditions if they are not followed. Therefore, be sure to observe all the safety caution items
described below.
About the pictograms
This symbol indicates an item for which caution must be exercised.
The pictogram shows the item to which attention must be paid.
This symbol indicates a prohibited action.
The prohibited item or action is shown inside or near the symbol.
This symbol indicates an action that must be taken, or an instruction.
The instruction is shown inside or near the symbol.
After the repair work is complete, be sure to conduct a test operation to ensure that the
equipment operates normally, and explain the cautions for operating the product to the
customer.
1.1.1Caution in Repair
Be sure to disconnect the power cable plug from the plug socket before
disassembling the equipment for a repair.
Working on the equipment that is connected to a power supply can cause an
electrical shook.
If it is necessary to supply power to the equipment to conduct the repair or
inspecting the circuits, do not touch any electrically charged sections of the
equipment.
If the refrigerant gas discharges during the repair work, do not touch the
discharging refrigerant gas.
The refrigerant gas can cause frostbite.
When disconnecting the suction or discharge pipe of the compressor at the
welded section, release the refrigerant gas completely at a well-ventilated
place first.
If there is a gas remaining inside the compressor, the refrigerant gas or
refrigerating machine oil discharges when the pipe is disconnected, and it can
cause injury.
If the refrigerant gas leaks during the repair work, ventilate the area. The
refrigerant gas can generate toxic gases when it contacts flames.
Warning
The step-up capacitor supplies high-voltage electricity to the electrical
components of the outdoor unit.
Be sure to discharge the capacitor completely before conducting repair work.
A charged capacitor can cause an electrical shock.
Do not start or stop the air conditioner operation by plugging or unplugging the
power cable plug.
Plugging or unplugging the power cable plug to operate the equipment can
cause an electrical shock or fire.
v
IntroductionSiBE04-401
Warning
Do not repair the electrical components with wet hands.
Working on the equipment with wet hands can cause an electrical shock.
Do not clean the air conditioner by splashing water.
Washing the unit with water can cause an electrical shock.
Be sure to provide the grounding when repairing the equipment in a humid or
wet place, to avoid electrical shocks.
Be sure to turn off the power switch and unplug the power cable when cleaning
the equipment.
The internal fan rotates at a high speed, and cause injury.
Do not tilt the unit when removing it.
The water inside the unit can spill and wet the furniture and floor.
Be sure to check that the refrigerating cycle section has cooled down
sufficiently before conducting repair work.
Working on the unit when the refrigerating cycle section is hot can cause burns.
Use the welder in a well-ventilated place.
Using the welder in an enclosed room can cause oxygen deficiency.
1.1.2Cautions Regarding Products after Repair
Warning
Be sure to use parts listed in the service parts list of the applicable model and
appropriate tools to conduct repair work. Never attempt to modify the
equipment.
The use of inappropriate parts or tools can cause an electrical shock,
excessive heat generation or fire.
When relocating the equipment, make sure that the new installation site has
sufficient strength to withstand the weight of the equipment.
If the installation site does not have sufficient strength and if the installation
work is not conducted securely, the equipment can fall and cause injury.
Be sure to install the product correctly by using the provided standard
installation frame.
Incorrect use of the installation frame and improper installation can cause the
equipment to fall, resulting in injury.
Be sure to install the product securely in the installation frame mounted on a
window frame.
If the unit is not securely mounted, it can fall and cause injury.
Be sure to use an exclusive power circuit for the equipment, and follow the
technical standards related to the electrical equipment, the internal wiring
regulations and the instruction manual for installation when conducting
electrical work.
Insufficient power circuit capacity and improper electrical work can cause an
electrical shock or fire.
For integral units
only
For integral units
only
vi
SiBE04-401Introduction
Warning
Be sure to use the specified cable to connect between the indoor and outdoor
units. Make the connections securely and route the cable properly so that there
is no force pulling the cable at the connection terminals.
Improper connections can cause excessive heat generation or fire.
When connecting the cable between the indoor and outdoor units, make sure
that the terminal cover does not lift off or dismount because of the cable.
If the cover is not mounted properly, the terminal connection section can cause
an electrical shock, excessive heat generation or fire.
Do not damage or modify the power cable.
Damaged or modified power cable can cause an electrical shock or fire.
Placing heavy items on the power cable, and heating or pulling the power cable
can damage the cable.
Do not mix air or gas other than the specified refrigerant (R410A / R22) in the
refrigerant system.
If air enters the refrigerating system, an excessively high pressure results,
causing equipment damage and injury.
If the refrigerant gas leaks, be sure to locate the leak and repair it before
charging the refrigerant. After charging refrigerant, make sure that there is no
refrigerant leak.
If the leak cannot be located and the repair work must be stopped, be sure to
perform pump-down and close the service valve, to prevent the refrigerant gas
from leaking into the room. The refrigerant gas itself is harmless, but it can
generate toxic gases when it contacts flames, such as fan and other heaters,
stoves and ranges.
When replacing the coin battery in the remote controller, be sure to disposed
of the old battery to prevent children from swallowing it.
If a child swallows the coin battery, see a doctor immediately.
Installation of a leakage breaker is necessary in some cases depending on the
conditions of the installation site, to prevent electrical shocks.
Do not install the equipment in a place where there is a possibility of
combustible gas leaks.
If a combustible gas leaks and remains around the unit, it can cause a fire.
Be sure to install the packing and seal on the installation frame properly.
If the packing and seal are not installed properly, water can enter the room and
wet the furniture and floor.
1.1.3Inspection after Repair
Check to make sure that the power cable plug is not dirty or loose, then insert
the plug into a power outlet all the way.
If the plug has dust or loose connection, it can cause an electrical shock or fire.
If the power cable and lead wires have scratches or deteriorated, be sure to
replace them.
Damaged cable and wires can cause an electrical shock, excessive heat
generation or fire.
Caution
For integral units
only
Warning
vii
IntroductionSiBE04-401
Warning
Do not use a joined power cable or extension cable, or share the same power
outlet with other electrical appliances, since it can cause an electrical shock,
excessive heat generation or fire.
Caution
Check to see if the parts and wires are mounted and connected properly, and
if the connections at the soldered or crimped terminals are secure.
Improper installation and connections can cause excessive heat generation,
fire or an electrical shock.
If the installation platform or frame has corroded, replace it.
Corroded installation platform or frame can cause the unit to fall, resulting in
injury.
Check the grounding, and repair it if the equipment is not properly grounded.
Improper grounding can cause an electrical shock.
Be sure to measure the insulation resistance after the repair, and make sure
that the resistance is 1 Mohm or higher.
Faulty insulation can cause an electrical shock.
Be sure to check the drainage of the indoor unit after the repair.
Faulty drainage can cause the water to enter the room and wet the furniture
and floor.
1.1.4Using Icons
Icons are used to attract the attention of the reader to specific information. The meaning of each
icon is described in the table below:
1.1.5Using Icons List
IconType of
Note:
Caution
Warning
Information
Description
NoteA “note” provides information that is not indispensable, but may
nevertheless be valuable to the reader, such as tips and tricks.
CautionA “caution” is used when there is danger that the reader, through
incorrect manipulation, may damage equipment, loose data, get
an unexpected result or has to restart (part of) a procedure.
WarningA “warning” is used when there is danger of personal injury.
viii
ReferenceA “reference” guides the reader to other places in this binder or
in this manual, where he/she will find additional information on a
specific topic.
SiBE04-401
Part 1
Part 1
Part 1Part 1
List of Functions
List of Functions
List of FunctionsList of Functions
1. List of Functions......................................................................................2
TypeHermetically Sealed Swing TypeHermetically Sealed Swing TypeHermetically Sealed Swing Type
Model1YC23NXD#A1YC23NXD#A1YC23NXD#A
Motor OutputW600600600
TypeFVC50KFVC50KFVC50K
ChargeL0.3750.3750.375
TypeR410AR410AR410A
Chargekg0.790.791. 01
m³/min
cfm
TypePropellerPropellerPropeller
Motor OutputW252525
H/LdBA46 / —46 / —48 / —
kW2.02.253.15
Btu/h6,8007,65010,750
kcal/h1,7201,9402,710
W6207001,045
φ
6.4
φ
9.5
φ
18.0
H7.7 (272)7.7 (272)7.7 (272)
M5.9 (208)5.9 (208)6.1 (215)
L4.2 (148)4.2 (148)4.4 (155)
SL———
H29 (1,025)29 (1,025)27.5 (972)
L———
φ
φ
φ
6.4
9.5
18.0
φ
6.4
φ
9.5
φ
18.0
Notes:
MAX. interunit piping length: 15m
MAX. interunit height difference: 15m
Amount of additional charge of refrigerant 20g/m for piping length exceeding 10m
The data are based on the conditions shown in the table below.
CoolingPiping Length
Indoor ; 27°CDB/19°CWB
Outdoor ; 35°CDB/24°CWB
7.5m
Conversion Formulae
kcal/h=kW×860
Btu/h=kW×3414
cfm=m³/min×35.3
12Specifications
SiBE04-401Specifications
1.2Heat Pump
1.2.1High Grade Models
230V, 50Hz
Models
Capacity
Rated (Min.~Max.)
Moisture RemovalL/h0.9—1.2—
Running Current (Rated)A2.83.53.94.4
Power Consumption
Rated (Min.~Max.)
Power Factor%79.682.179.393.7
COP (Rated)W/W4.004.003.603.64
Piping
Connections
Heat InsulationBoth Liquid and Gas PipesBoth Liquid and Gas Pipes
Indoor UnitsFTXS20CVMB(9)FTXS25CVMB(9)(8)
Front Panel ColorWhiteWhite
Air Flow Rate
Fan
Air Direction ControlRight, Left, Horizontal and DownwardRight, Left, Horizontal and Downward
Air FilterRemovable / Washable / Mildew ProofRemovable / Washable / Mildew Proof
Running Current (Rated)A0.180.180.180.18
Power Consumption (Rated)W40404040
Power Factor%96.696.696.696.6
Temperature ControlMicrocomputer ControlMicrocomputer Control
Dimensions (H×W×D)mm273×784×195273×784×195
Packaged Dimensions (W×D×H)mm834×325×258834×325×258
Weightkg7.57.5
Gross Weightkg1111
Operation
Sound
Sound Power HdBA56565656
Outdoor UnitsRXS20CVMBRXS25CVMB
Casing ColorIvory WhiteIvory White
Compressor
Refrigerant
Oil
Refrigerant
Air Flow Rate
Fan
Running Current (Rated)A2.623.323.724.22
Power Consumption (Rated)W460635655895
Power Factor%76.383.276.692.2
Starting CurrentA3.54.4
Dimensions (H×W×D)mm550×765×285550×765×285
Packaged Dimensions (W×D×H)mm882×363×589882×363×589
Weightkg3030
Gross Weightkg3535
Operation
Sound
Sound Power HdBA61626162
Drawing No.3D044245B3D044246B
Amount of additional charge of refrigerant 20g/m for piping length exceeding 10m
The data are based on the conditions shown in the table below.
CoolingHeatingPiping Length
Indoor ; 27°CDB/19°CWB
Outdoor ; 35°CDB/24°CWB
Indoor ; 20°CDB
Outdoor ; 7°CDB/6°CWB
7.5m
Conversion Formulae
kcal/h=kW×860
Btu/h=kW×3414
cfm=m³/min×35.3
Specifications13
SpecificationsSiBE04-401
230V, 50Hz
Models
Capacity
Rated (Min.~Max.)
Moisture RemovalL/h1.9—
Running Current (Rated)A4.95.4
Power Consumption
Rated (Min.~Max.)
Power Factor%94.395.4
COP (Rated)W/W3.213.42
Piping
Connections
Heat InsulationBoth Liquid and Gas Pipes
Indoor UnitsFTXS35CVMB(9)(8)
Front Panel ColorWhit e
Air Flow Rate
Fan
Air Direction ControlRight, Left, Horizontal and Downward
Air FilterRemovable / Washable / Mildew Proof
Running Current (Rated)A0.180.18
Power Consumption (Rated)W4040
Power Factor%96.696.6
Temperature ControlMicrocomputer Control
Dimensions (H×W×D)mm273×784×195
Packaged Dimensions (W×D×H)mm834×325×258
Weightkg7.5
Gross Weightkg11
Operation
Sound
Sound Power HdBA5757
Outdoor UnitsRXS35CVMB
Casing ColorIvory White
Compressor
Refrigerant
Oil
Refrigerant
Air Flow Rate
Fan
Running Current (Rated)A4.725.22
Power Consumption (Rated)W1,0201,130
Power Factor%94.094.1
Starting CurrentA5.4
Dimensions (H×W×D)mm550×765×285
Packaged Dimensions (W×D×H)mm882×363×589
Weightkg32
Gross Weightkg38
Operation
Sound
Sound PowerdBA6263
Drawing No.3D044247B
Indoor UnitsFTXS35CVMB(9)(8)
Outdoor Units
kW3.4 (1.4~3.8)4.0 (1.4~5.0)
Btu/h11,600 (4,750~12,950)13,650 (4,750~17,050)
kcal/h2,920 (1,200~3,270)3,440 (1,200~4,300)
W1,060 (300~1,300)1,170 (310~1,590)
Liquidmm
Gasmm
Drainmm
H7.7 (272)8.1 (286)
m³/min
(cfm)
TypeCross Flow Fan
Motor OutputW18
SpeedSteps5 Steps, Silent and Auto
H/M/L/SLdBA39 / 33 / 26 / 2339 / 34 / 29 / 26
TypeHermetically Sealed Swing Type
Model1YC23NXD#A
Motor OutputW600
TypeFVC50K
ChargeL0.375
TypeR410A
Chargekg1.00
m³/min
(cfm)
TypePropeller
Motor OutputW35
H/LdBA47 / 4448 / 45
M6.0 (212)6.7 (237)
L4.4 (155)5.3 (187)
SL3.8 (134)4.6 (162)
H31.3 (1,105)28.1 (992)
L22.4 (791)22.4 (791)
CoolingHeating
RXS35CVMB
φ
6.4
φ
9.5
φ
18.0
Notes:
MAX. interunit piping length: 20m
MAX. interunit height difference: 15m
Amount of additional charge of refrigerant 20g/m for piping length exceeding 10m
The data are based on the conditions shown in the table below.
CoolingHeatingPiping Length
Indoor ; 27°CDB/19°CWB
Outdoor ; 35°CDB/24°CWB
Indoor ; 20°CDB
Outdoor ; 7°CDB/6°CWB
7.5m
Conversion Formulae
kcal/h=kW×860
Btu/h=kW×3414
cfm=m³/min×35.3
14Specifications
SiBE04-401Specifications
230V, 50Hz
Models
Capacity
Rated (Min.~Max.)
Moisture RemovalL/h0.9—1.2—
Running Current (Rated)A2.83.53.94.4
Power Consumption
Rated (Min.~Max.)
Power Factor%79.682.179.393.7
COP (Rated)W/W4.004.003.603.64
Piping
Connections
Heat InsulationBoth Liquid and Gas PipesBoth Liquid and Gas Pipes
Indoor UnitsATXS2 0CVMB(9)ATXS25CVMB(9)
Front Panel ColorWhiteWhite
Air Flow Rate
Fan
Air Direction ControlRight, Left, Horizontal and DownwardRight, Left, Horizontal and Downward
Air FilterRemovable / Washable / Mildew ProofRemovable / Washable / Mildew Proof
Running Current (Rated)A0.180.180.180.18
Power Consumption (Rated)W40404040
Power Factor%96.696.696.696.6
Temperature ControlMicrocomputer ControlMicrocomputer Control
Dimensions (H×W×D)mm273×784×185273×784×185
Packaged Dimensions (W×D×H)mm834×325×258834×325×258
Weightkg7.57.5
Gross Weightkg1111
Operation
Sound
Sound Power HdBA56565656
Outdoor UnitsARXS20CVMBARXS25CVMB
Casing ColorIvory WhiteIvory White
Compressor
Refrigerant
Oil
Refrigerant
Air Flow Rate m³/min (cfm)
Fan
Running Current (Rated)A2.623.323.724.22
Power Consumption (Rated)W460635655895
Power Factor%76.383.276.692.2
Starting CurrentA3.54.4
Dimensions (H×W×D)mm550×765×285550×765×285
Packaged Dimensions (W×D×H)mm882×363×589882×363×589
Weightkg3030
Gross Weightkg3535
Operation
Sound
Sound Power HdBA61626162
Drawing No.3D044251B3D044252B
Amount of additional charge of refrigerant 20g/m for piping length exceeding 10m
The data are based on the conditions shown in the table below.
CoolingHeatingPiping Length
Indoor ; 27°CDB/19°CWB
Outdoor ; 35°CDB/24°CWB
Indoor ; 20°CDB
Outdoor ; 7°CDB/6°CWB
7.5m
Conversion Formulae
kcal/h=kW×860
Btu/h=kW×3414
cfm=m³/min×35.3
Specifications15
SpecificationsSiBE04-401
230V, 50Hz
Models
Capacity
Rated (Min.~Max.)
Moisture RemovalL/h1.9—
Running Current (Rated)A4.95.4
Power Consumption
Rated (Min.~Max.)
Power Factor%94.395.4
COP (Rated)W/W3.213.42
Piping
Connections
Heat InsulationBoth Liquid and Gas Pipes
Indoor UnitsATXS35CVMB(9)
Front Panel ColorWhit e
Air Flow Rate
Fan
Air Direction ControlRight, Left, Horizontal and Downward
Air FilterRemovable / Washable / Mildew Proof
Running Current (Rated)A0.180.18
Power Consumption (Rated)W4040
Power Factor%96.696.6
Temperature ControlMicrocomputer Control
Dimensions (H×W×D)mm273×784×185
Packaged Dimensions (W×D×H)mm834×325×258
Weightkg7.5
Gross Weightkg11
Operation
Sound
Sound Power HdBA5757
Outdoor UnitsARXS35CVMB
Casing ColorIvory White
Compressor
Refrigerant
Oil
Refrigerant
Air Flow Rate m³/min (cfm)
Fan
Running Current (Rated)A4.725.22
Power Consumption (Rated)W1,0201,130
Power Factor%94.094.1
Starting CurrentA5.4
Dimensions (H×W×D)mm550×765×285
Packaged Dimensions (W×D×H)mm882×363×589
Weightkg32
Gross Weightkg38
Operation
Sound
Sound Power HdBA6263
Drawing No.3D044253B
Indoor UnitsATXS35CVMB(9)
Outdoor Units
kW3.4 (1.4~3.8)4.0 (1.4~5.0)
Btu/h11,600 (4,750~12,950)13,650 (4,750~17,050)
kcal/h2,920 (1,200~3,270)3,440 (1,200~4,300)
W1,060 (300~1,300)1,170 (310~1,590)
Liquidmm
Gasmm
Drainmm
H7.7 (272)8.1 (286)
m³/min
(cfm)
TypeCross Flow Fan
Motor OutputW18
SpeedSteps5 Steps, Silent and Auto
H/M/L/SLdBA39 / 33 / 26 / 2339 / 34 / 29 / 26
TypeHermetically Sealed Swing Type
Model1YC23NXD#A
Motor OutputW600
TypeFVC50K
ChargeL0.375
TypeR410A
Chargekg1.00
TypePropeller
Motor OutputW35
H/LdBA47 / 4448 / 45
M6.1 (215)6.7 (237)
L4.4 (155)5.3 (187)
SL3.8 (134)4.6 (162)
H31.3 (1,105)28.1 (992)
L22.4 (791)22.4 (791)
CoolingHeating
ARXS35CVMB
φ
6.4
φ
9.5
φ
18.0
Notes:
MAX. interunit piping length: 20m
MAX. interunit height difference: 15m
Amount of additional charge of refrigerant 20g/m for piping length exceeding 10m
The data are based on the conditions shown in the table below.
CoolingHeatingPiping Length
Indoor ; 27°CDB/19°CWB
Outdoor ; 35°CDB/24°CWB
Indoor ; 20°CDB
Outdoor ; 7°CDB/6°CWB
7.5m
Conversion Formulae
kcal/h=kW×860
Btu/h=kW×3414
cfm=m³/min×35.3
16Specifications
SiBE04-401Specifications
1.2.2Standard Grade Models
230V, 50Hz
Models
Capacity
Rated (Min.~Max.)
Moisture RemovalL/h0.9—1.2—
Running Current (Rated)A3.34.03.74.4
Power Consumption
Rated (Min.~Max.)
Power Factor%81.782.682.382.5
COP (Rated)W/W3.233.423.213.41
Piping
Connections
Heat InsulationBoth Liquid and Gas PipesBoth Liquid and Gas Pipes
Indoor UnitsFTXS20CVMB(9)FTXS25CVMB(9)(8)
Front Panel ColorWhiteWhite
Air Flow Rate
Fan
Air Direction ControlRight, Left, Horizontal and DownwardRight, Left, Horizontal and Downward
Air FilterRemovable / Washable / Mildew ProofRemovable / Washable / Mildew Proof
Running Current (Rated)A0.180.180.180.18
Power Consumption (Rated)W40404040
Power Factor%96.696.696.696.6
Temperature ControlMicrocomputer ControlMicrocomputer Control
Dimensions (H×W×D)mm273×784×195273×784×195
Packaged Dimensions (W×D×H)mm834×325×258834×325×258
Weightkg7.57.5
Gross Weightkg1111
Operation
Sound
Sound Power HdBA56565656
Outdoor UnitsRXH20CVMB9RXH25CVMB9
Casing ColorIvory WhiteIvory White
Compressor
Refrigerant
Oil
Refrigerant
Air Flow Rate
Fan
Running Current (Rated)A3.123.823.524.22
Power Consumption (Rated)W580720660795
Power Factor%80.881.981.581.9
Starting CurrentA4.04.4
Dimensions (H×W×D)mm560×695×265560×695×265
Packaged Dimensions (W×D×H)mm824×337×599824×337×599
Weightkg3131
Gross Weightkg3636
Operation
Sound
Sound Power HdBA61626162
Drawing No.C:3D044446C:3D044447
TypeHermetically Sealed Swing TypeHermetically Sealed Swing Type
Model1YC23NXD#A1YC23NXD#A
Motor OutputW600600
TypeFVC50KFVC50K
ChargeL0.3750.375
TypeR410AR410A
Chargekg0.790.79
m³/min
(cfm)
TypePropellerPropeller
Motor OutputW2525
H/LdBA46 / —47 / —46 / —47 / —
M5.9 (208)6.5 (230)5.9 (208)6.5 (230)
L4.2 (148)5.3 (187)4.2 (148)5.3 (187)
SL3.6 (127)4.6 (162)3.6 (127)4.6 (162)
H
L
CoolingHeatingCoolingHeating
29 (1,025)25.5 (901)29 (1,025)25.5 (901)
RXH20CVMB9RXH25CVMB9
φ
6.4
φ
9.5
φ
18.0
————
φ
φ
φ
6.4
9.5
18.0
Notes:
MAX. interunit piping length: 15m
MAX. interunit height difference: 15m
Amount of additional charge of refrigerant 20g/m for piping length exceeding 10m
The data are based on the conditions shown in the table below.
CoolingHeatingPiping Length
Indoor ; 27°CDB/19°CWB
Outdoor ; 35°CDB/24°CWB
Indoor ; 20°CDB
Outdoor ; 7°CDB/6°CWB
7.5m
Conversion Formulae
kcal/h=kW×860
Btu/h=kW×3414
cfm=m³/min×35.3
Specifications17
SpecificationsSiBE04-401
230V, 50Hz
Models
Capacity
Rated (Min.~Max.)
Moisture RemovalL/h1.7—
Running Current (Rated)A4.94.9
Power Consumption
Rated (Min.~Max.)
Power Factor%92.793.6
COP (Rated)W/W3.013.41
Piping
Connections
Heat InsulationBoth Liquid and Gas Pipes
Indoor UnitsFTXS35CVMB(9)(8)
Front Panel ColorWhite
Air Flow Rate
Fan
Air Direction ControlRight, Left, Horizontal and Downward
Air FilterRemovable / Washable / Mildew Proof
Running Current (Rated)A0.180.18
Power Consumption (Rated)W4040
Power Factor%96.696.6
Temperature ControlMicrocomputer Control
Dimensions (H×W×D)mm273×784×195
Packaged Dimensions (W×D×H)mm834×325×258
Weightkg7.5
Gross Weightkg11
Operation
Sound
Sound Power HdBA5757
Outdoor UnitsRXH35CVMB9
Casing ColorIvory White
Compressor
Refrigerant
Oil
Refrigerant
Air Flow Rate
Fan
Running Current (Rated)A4.724.72
Power Consumption (Rated)W1,0051,015
Power Factor%92.693.5
Starting CurrentA4.9
Dimensions (H×W×D)mm560×695×265
Packaged Dimensions (W×D×H)mm824×337×599
Weightkg33
Gross Weightkg38
Operation
Sound
Sound Power HdBA6363
Drawing No.C:3D044448
Indoor UnitsFTXS35CVMB(9)(8)
Outdoor Units
kW3.15 (1.4~3.8)3.6 (1.4~5.0)
Btu/h10,750 (4,750~12,950)12,300 (4,750~17,050)
kcal/h2,710 (1,200~3,270)3,100 (1,200~4,300)
W1,045 (460~1,425)1,055 (405~1,900)
Liquidmm
Gasmm
Drainmm
H7.7 (272)8.1 (286)
m³/min
(cfm)
TypeCross Flow Fan
Motor OutputW18
SpeedSteps5 Steps, Silent and Auto
H/M/L/SLdBA39 / 33 / 26 / 2339 / 34 / 29 / 26
TypeHermetically Sealed Swing Type
Model1YC23NXD#A
Motor OutputW600
TypeFVC50K
ChargeL0.375
TypeR410A
Chargekg1.01
m³/min
(cfm)
TypePropeller
Motor OutputW25
H/LdBA48 / —48 / —
M6.0 (212)6.7 (237)
L4.4 (155)5.3 (187)
SL3.8 (134)4.6 (162)
H
L
CoolingHeating
27.5 (972)23.5 (830)
——
RXH35CVMB9
φ
6.4
φ
9.5
φ
18.0
Notes:
MAX. interunit piping length: 15m
MAX. interunit height difference: 15m
Amount of additional charge of refrigerant 20g/m for piping length exceeding 10m
The data are based on the conditions shown in the table below.
CoolingHeatingPiping Length
Indoor ; 27°CDB/19°CWB
Outdoor ; 35°CDB/24°CWB
Indoor ; 20°CDB
Outdoor ; 7°CDB/6°CWB
7.5m
Conversion Formulae
kcal/h=kW×860
Btu/h=kW×3414
cfm=m³/min×35.3
18Specifications
SiBE04-401Specifications
230V, 50Hz
Models
Capacity
Rated (Min.~Max.)
Moisture RemovalL/h0.9—1.2—
Running Current (Rated)A3.34.03.74.4
Power Consumption
Rated (Min.~Max.)
Power Factor%81.782.682.382.5
COP (Rated)W/W3.233.423.213.41
Piping
Connections
Heat InsulationBoth Liquid and Gas PipesBoth Liquid and Gas Pipes
Indoor UnitsATXS2 0CVMB(9)ATXS25CVMB(9)
Front Panel ColorWhiteWhite
Air Flow Rate
Fan
Air Direction ControlRight, Left, Horizontal and DownwardRight, Left, Horizontal and Downward
Air FilterRemovable / Washable / Mildew ProofRemovable / Washable / Mildew Proof
Running Current (Rated)A0.180.180.180.18
Power Consumption (Rated)W40404040
Power Factor%96.696.696.696.6
Temperature ControlMicrocomputer ControlMicrocomputer Control
Dimensions (H×W×D)mm273×784×185273×784×185
Packaged Dimensions (W×D×H)mm834×325×258834×325×258
Weightkg7.57.5
Gross Weightkg1111
Operation
Sound
Sound Power HdBA56565656
Outdoor UnitsARXH20CVMB9ARXH25CVMB9
Casing ColorIvory WhiteIvory White
Compressor
Refrigerant
Oil
Refrigerant
Air Flow Rate m³/min (cfm)
Fan
Running Current (Rated)A3.123.823.524.22
Power Consumption (Rated)W580720660795
Power Factor%80.881.981.581.9
Starting CurrentA4.04.4
Dimensions (H×W×D)mm560×695×265560×695×265
Packaged Dimensions (W×D×H)mm824×337×599824×337×599
Weightkg3131
Gross Weightkg3636
Operation
Sound
Sound Power HdBA61626162
Drawing No.C:3D044449C:3D044450
TypeHermetically Sealed Swing TypeHermetically Sealed Swing Type
Model1YC23NXD#A1YC23NXD#A
Motor OutputW600600
TypeFVC50KFVC50K
ChargeL0.3750.375
TypeR410AR410A
Chargekg0.790.79
TypePropellerPropeller
Motor OutputW2525
H/LdBA46 / —47 / —46 / —47 / —
M5.9 (208)6.5 (230)5.9 (208)6.5 (230)
L4.2 (148)5.3 (187)4.2 (148)5.3 (187)
SL3.6 (127)4.6 (162)3.6 (127)4.6 (162)
H29 (1,025)25.5 (901)29 (1,025)25.5 (901)
L————
CoolingHeatingCoolingHeating
ARXH20CVMB9ARXH25CVMB9
φ
φ
φ
6.4
9.5
18.0
φ
φ
φ
6.4
9.5
18.0
Notes:
MAX. interunit piping length: 15m
MAX. interunit height difference: 15m
Amount of additional charge of refrigerant 20g/m for piping length exceeding 10m
The data are based on the conditions shown in the table below.
CoolingHeatingPiping Length
Indoor ; 27°CDB/19°CWB
Outdoor ; 35°CDB/24°CWB
Indoor ; 20°CDB
Outdoor ; 7°CDB/6°CWB
7.5m
Conversion Formulae
kcal/h=kW×860
Btu/h=kW×3414
cfm=m³/min×35.3
Specifications19
SpecificationsSiBE04-401
230V, 50Hz
Models
Capacity
Rated (Min.~Max.)
Moisture RemovalL/h1.7—
Running Current (Rated)A4.94.9
Power Consumption
Rated (Min.~Max.)
Power Factor%92.793.6
COP (Rated)W/W3.013.41
Piping
Connections
Heat InsulationBoth Liquid and Gas Pipes
Indoor UnitsATXS35CVMB(9)
Front Panel ColorWhite
Air Flow Rate
Fan
Air Direction ControlRight, Left, Horizontal and Downward
Air FilterRemovable / Washable / Mildew Proof
Running Current (Rated)A0.180.18
Power Consumption (Rated)W4040
Power Factor%96.696.6
Temperature ControlMicrocomputer Control
Dimensions (H×W×D)mm273×784×185
Packaged Dimensions (W×D×H)mm834×325×258
Weightkg7.5
Gross Weightkg11
Operation
Sound
Sound Power HdBA5757
Outdoor UnitsARXH35CVMB9
Casing ColorIvory White
Compressor
Refrigerant
Oil
Refrigerant
Air Flow Rate m³/min (cfm)
Fan
Running Current (Rated)A4.724.72
Power Consumption (Rated)W1,0051,015
Power Factor%92.693.5
Starting CurrentA4.9
Dimensions (H×W×D)mm560×695×265
Packaged Dimensions (W×D×H)mm824×337×599
Weightkg33
Gross Weightkg38
Operation
Sound
Sound Power HdBA6363
Drawing No.C:3D044451
Indoor UnitsATXS35CVMB(9)
Outdoor Units
kW3.15 (1.4~3.8)3.6 (1.4~5.0)
Btu/h10,750 (4,750~12,950)12,300 (4,750~17,050)
kcal/h2,710 (1,200~3,270)3,100 (1,200~4,300)
W1,045 (460~1,425)1,055 (405~1,900)
Liquidmm
Gasmm
Drainmm
H7.7 (272)8.1 (286)
m³/min
(cfm)
TypeCross Flow Fan
Motor OutputW18
SpeedSteps5 Steps, Silent and Auto
H/M/L/SLdBA39 / 33 / 26 / 2339 / 34 / 29 / 26
TypeHermetically Sealed Swing Type
Model1YC23NXD#A
Motor OutputW600
TypeFVC50K
ChargeL0.375
TypeR410A
Chargekg1.01
TypePropeller
Motor OutputW25
H/LdBA48 / —48 / —
M6.1 (215)6.7 (237)
L4.4 (155)5.3 (187)
SL3.8 (134)4.6 (162)
H27.5 (972)23.5 (830)
L——
CoolingHeating
ARXH35CVMB9
φ
6.4
φ
9.5
φ
18.0
Notes:
MAX. interunit piping length: 15m
MAX. interunit height difference: 15m
Amount of additional charge of refrigerant 20g/m for piping length exceeding 10m
The data are based on the conditions shown in the table below.
CoolingHeatingPiping Length
Indoor ; 27°CDB/19°CWB
Outdoor ; 35°CDB/24°CWB
Indoor ; 20°CDB
Outdoor ; 7°CDB/6°CWB
7.5m
Conversion Formulae
kcal/h=kW×860
Btu/h=kW×3414
cfm=m³/min×35.3
20Specifications
SiBE04-401Specifications
1.2.3Non-lnverter Models
230V, 50Hz
Models
Capacity
Rated (Min.~Max.)
Moisture RemovalL/h0.9—1.2—
Running Current (Rated)A3.34.03.74.4
Power Consumption
Rated (Min.~Max.)
Power Factor%81.782.682.382.5
COP (Rated)W/W3.233.423.213.41
Piping
Connections
Heat InsulationBoth Liquid and Gas PipesBoth Liquid and Gas Pipes
Indoor UnitsFTYN20CVMB9FTYN25CVMB9
Front Panel ColorWhiteWhite
Air Flow Rate
Fan
Air Direction ControlRight, Left, Horizontal and DownwardRight, Left, Horizontal and Downward
Air FilterRemovable / Washable / Mildew ProofRemovable / Washable / Mildew Proof
Running Current (Rated)A0.180.180.180.18
Power Consumption (Rated)W40404040
Power Factor%96.696.696.696.6
Temperature ControlMicrocomputer ControlMicrocomputer Control
Dimensions (H×W×D)mm273×784×185273×784×185
Packaged Dimensions (W×D×H)mm834×325×258834×325×258
Weightkg7.57.5
Gross Weightkg1111
Operation
Sound
Sound Power HdBA56565656
Outdoor UnitsRYN20CVMB9RYN25CVMB9
Casing ColorIvory WhiteIvory White
Compressor
Refrigerant
Oil
Refrigerant
Air Flow Rate m³/min (cfm)
Fan
Running Current (Rated)A3.123.823.524.22
Power Consumption (Rated)W580720660795
Power Factor%80.881.981.581.9
Starting CurrentA4.04.4
Dimensions (H×W×D)mm560×695×265560×695×265
Packaged Dimensions (W×D×H)mm824×337×599824×337×599
Weightkg3131
Gross Weightkg3636
Operation
Sound
Sound Power HdBA61626162
Drawing No.3D0444523D044453
Indoor UnitsFTYN20CVMB9FTYN25CVMB9
Outdoor Units
kW2.02.62.252.85
Btu/h6,8008,8507,6509,700
kcal/h1,7202,2401,9402,450
W620760700835
Liquidmm
Gasmm
Drainmm
H7.7 (272)7.8 (275)7.7 (272)7.8 (275)
m³/min
(cfm)
TypeCross Flow FanCross Flow Fan
Motor OutputW1818
SpeedSteps5 Steps and Auto5 Steps and Auto