Daikin FWT02BATNMV1, FWT03BATNMV1, FWT04BATNMV1, FWT05BATNMV1, FWT06BATNMV1 Installation manual

INSTALLATION
MANUAL

Models
FWT02BATNMV1
FWT03BATNMV1
FWT04BATNMV1

Installation manual

Chilled Water Fan Coil Units

English

FWT05BATNMV1
FWT06BATNMV1

IM-WMGW-1205(1)-DAIKIN
PART NO.: R08019029236A

Indoor Unit

OUTLINE AND DIMENSIONS

A

TOP VIEW

C

B

FRONT VIEW SIDE VIEW

English

Original Instruction

I

INSTALLATION PLATE

FDG

H

E

K

L

SEE DETAIL A

I

MJ

WATER OUTLET

WATER INLET

ON

DETAIL A

All dimensions are in mm/(in)

Dimension A B C D E F G H I J K L M N O
FWT02BATNMV1 799 260 198 379 246 185 124 8 56 50 350 379 50 128 132

(31.5) (10.2) (7.8) (15.0) (9.7) (7.3) (4.9) (0.3) (2.2) (2.0) (13.8) (15.0) (2.0) (5.1) (5.2)

FWT03BATNMV1/ 899 260 198 590 246 185 124 8 56 50 435 495 50 128 132
FWT04BATNMV1 (35.4) (10.2) (7.8) (23.2) (9.7) (7.3) (4.9) (0.3) (2.2) (2.0) (17.1) (19.5) (2.0) (5.1) (5.2)

1

Indoor Unit

A

TOP VIEW

B

FRONT VIEW

CENTER LINE

I

J

INSTALLATION PLATE

A

F

H

DG

M

I

C

SIDE VIEW

WATER OUTLET

WATER INLET

ON

E

B

INSTALLATION PLATE

K

L

SEE DETAIL A

All dimensions are in mm/(in)

DETAIL A

Dimension A B C D E F G H I J K L M N O
FWT05BATNMV1/ 1060 310 220 912 294 99 51 8 48 43 369 453 160 138 160

FWT06BATNMV1 (41.7) (12.2) (8.6) (35.9) (11.6) (3.9) (2.0) (0.3) (1.9) (1.7) (14.5) (17.8) (6.3) (5.4) (6.3)

2

INSTALLATION MANUAL

This manual provides the procedures of installation to ensure a safe and good standard of operation for the air
conditioner unit.
Special adjustment may be necessary to suit local requirements.
Before using your air conditioner, please read this instruction manual carefully and keep it for future reference.
This appliance is intended to be used by expert or trained users in shops, in light industry and on farms, or for
commercial use by lay persons.

SAFETY PRECAUTIONS

English

! WARNING

• Installation and maintenance should be performed by
qualified persons who are familiar with local code and
regulation, and experienced with this type of appliance.

• All field wiring must be installed in accordance with
the national wiring regulation.

• Ensure that the rated voltage of the unit corresponds to
that of the name plate before commencing wiring work
according to the wiring diagram.

• The unit must be GROUNDED to prevent possible
hazard due to insulation failure.

• All electrical wiring must not touch the water piping or
any moving parts of the fan motors.

• Confirm that the unit has been switched OFF before
installing or servicing the unit.

• Risk of electric shock, can cause injury or death.
Disconnect all remain electric power supplies before
servicing.

• DO NOT pull out the power cord when the power is
ON. This may cause serious electrical shocks which may
result in the fire hazards.

• Keep the indoor and outdoor units, power cable and
transmission wiring, at least 1m from TVs and radios,
to prevent distorted pictures and static. (Depending on
the type and source of the electrical waves, static may
be heard even when more than 1m away).

! CAUTION

Please take note of the following important points when
installing.

• Ensure that the drainage piping is connected
properly.

If the drainage piping is not connected properly, it
may cause water leakage which will dampen the
furniture.

• Ensure that the unit’s panel is closed after service or
installation.

Unsecured panels will cause the unit to operate
noisily.

• Sharp edges and coil surfaces are potential locations
which may cause injury hazards. Avoid from being
in contact with these places.

• Before turning off the power supply set the remote
controller’s ON/OFF switch to the “OFF” position
to prevent the nuisance tripping of the unit. If this is

not done, the unit’s fans will start turning automatically
when power resumes, posing a hazard to service
personnel or the user.

• Do not operate any heating apparatus too close to
the air conditioner unit. This may cause the plastic

panel to melt or deform as a result of the excessive heat.

• Ensure the color of wires of the outdoor unit and the
terminal markings are same to the indoors
respectively.

• IMPORTANT: DO NOT INSTALL OR USE THE
AIR CONDITIONER UNIT IN A LAUNDRY
ROOM.

• Avoid direct contact of any coil treatment cleaners
on plastic part. This may cause plastic part to deform
as a result of chemical reaction.

NOTICE

Disposal requirements

Your air conditioning product is marked with this symbol. This means that electrical and electronic products
shall not be mixed with unsorted household waste.

Do not try to dismantle the system yourself: the dismantling of the air conditioning system, treatment of the
refrigerant, of oil and of other parts must be done by a qualified installer in accordance with relevant local and
national legislation.

Air conditioners must be treated at a specialized treatment facility for re-use, recycling and recovery. By
ensuring this product is disposed of correctly, you will help to prevent potential negative consequences for the
environment and human health. Please contact the installer or local authority for more information.

Batteries must be removed from the remote controller and disposed of separately in accordance with relevant
local and national legislation.

3