Daikin FWT02AATNMV1, FWT03AATNMV1, FWT04AATNMV1, FWT05AATNMV1, FWT06AATNMV1 Installation manuals

INSTALLATION
MANUAL

Models
FWT02AATNMV1
FWT03AATNMV1
FWT04AATNMV1

Installation manual

Chilled Water Fan Coil Units

English

FWT05AATNMV1
FWT06AATNMV1

Indoor Unit

OUTLINE AND DIMENSIONS

A

TOP VIEW

C

B

FRONT VIEW SIDE VIEW

English

I

INSTALLATION PLATE

FDG

H

E

K

L

SEE DETAIL A

I

MJ

WATER OUTLET

WATER INLET

ON

DETAIL A

Dimension A B C D E F G H I J K L M N O
FWT02AATNMV1 799 260 198 379 246 185 124 8 56 50 350 379 50 128 132

(31,5) (10,2) (7,8) (15,0) (9,7) (7,3) (4,9) (0,3) (2,2) (2,0) (13,8) (15,0) (2,0) (5,1) (5,2)

FWT03AATNMV1 / 899 260 198 590 246 185 124 8 56 50 435 495 50 128 132
FWT04AATNMV1 (35,4) (10,2) (7,8) (23,2) (9,7) (7,3) (4,9) (0,3) (2,2) (2,0) (17,1) (19,5) (2,0) (5,1) (5,2)

1

Indoor Unit

A

TOP VIEW

B

FRONT VIEW

CENTER LINE

I

J

INSTALLATION PLATE

A

F

H

DG

M

I

C

SIDE VIEW

WATER OUTLET

WATER INLET

ON

E

B

INSTALLATION PLATE

K

L

SEE DETAIL A

DETAIL A

Dimension A B C D E F G H I J K L M N O
FWT05AATNMV1 / 1060 310 220 912 294 99 51 8 48 43 369 453 160 138 160

FWT06AATNMV1 (41,7) (12,2) (8,6) (35,9) (11,6) (3,9) (2,0) (0,3) (1,9) (1,7) (14,5) (17,8) (6,3) (5,4) (6,3)

2

SAFETY PRECAUTIONS

! WARNING

• Installation and maintenance should be performed by
qualified persons who are familiar with local code and
regulation, and experienced with this type of appliance.

• All field wiring must be installed in accordance with the
national wiring regulation.

• Ensure that the rated voltage of the unit corresponds to
that of the name plate before commencing wiring work
according to the wiring diagram.

• The unit must be GROUNDED to prevent possible hazard
due to insulation failure.

• All electrical wiring must not touch the water piping or
any moving parts of the fan motors.

• Confirm that the unit has been switched OFF before
installing or servicing the unit.

• Risk of electric shock, can cause injury or death.
Disconnect all remain electric power supplies before
servicing.

• DO NOT pull out the power cord when the power is ON.
This may cause serious electrical shocks which may result
in the fire hazards.

• Keep the indoor and outdoor units, power cable and
transmission wiring, at least 1m from TVs and radios, to
prevent distorted pictures and static. {Depending on the
type and source of the electrical waves, static may be heard
even when more than 1m away}.

! CAUTION

Please take note of the following important points when
installing.

• Ensure that the drainage piping is connected properly.

If the drainage piping is not connected properly, it may
cause water leakage which will dampen the furniture.

• Ensure that the unit’s panel is closed after service or
installation.

Unsecured panels will cause the unit to operate noisily.

• Sharp edges and coil surfaces are potential locations which
may cause injury hazards. Avoid from being in contact
with these places.

• Before turning off the power supply set the remote
controller’s ON/OFF switch to the “OFF” position to
prevent the nuisance tripping of the unit. If this is not done,

the unit’s fans will start turning automatically when power
resumes, posing a hazard to service personnel or the user.

• Do not operate any heating apparatus too close to the air
conditioner unit. This may cause the plastic panel to melt or

deform as a result of the excessive heat.

• Ensure the color of wires of the outdoor unit and the
terminal markings are same to the indoors respectively.

• IMPORTANT : DO NOT INSTALL OR USE THE AIR
CONDITIONER UNIT IN A LAUNDRY ROOM.

English

NOTICE

Disposal requirements

Your air conditioning product is marked with this symbol. This means that electrical and electronic products shall not
be mixed with unsorted household waste.

Do not try to dismantle the system yourself: the dismantling of the air conditioning system, treatment of the refrigerant,
of oil and of other parts must be done by a qualified installer in accordance with relevant local and national legislation.

Air conditioners must be treated at a specialized treatment facility for re-use, recycling and recovery. By ensuring this
product is disposed of correctly, you will help to prevent potential negative consequences for the environment and
human health. Please contact the installer or local authority for more information.

Batteries must be removed from the remote controller and disposed of separately in accordance with relevant local
and national legislation.

3