Daewoo DWC-UD121X User Manual

1
PARTS AND FEATURES.................................................................................................................2
WASHER SAFETY...........................................................................................................................3
INSTALLATION INSTRUCTIONS....................................................................................................4
INLET HOSE CONNECTION...........................................................................................................5
ELECTRICAL REQUIREMENTS .....................................................................................................6
OPERATING YOUR WASHER........................................................................................................7
WASHING PROGRAM...................................................................................................................11
WASHING PROCEDURE AND SELECTION ................................................................................12
GUIDE FOR OTHER USEFUL PROGRAMS.................................................................................24
MAINTENANCE .............................................................................................................................29
HOW TO CLEAN THE FILTER......................................................................................................30
REMOVING STAINS......................................................................................................................31
TROUBLE SHOOTING ..................................................................................................................32
SPECIFICATION............................................................................................................................33
Features
DWC-UD121X Series / DWD-UD121X Series
Washing Machine Instruction Manual
A NOTE T O YOU
Thank you for buying a DAEWOO appliance. DAEWOO washers are easy to use, save time, and help you manage your home better. This manual contains valuable information about how to operate and maintain your washer property and safely. Please read it carefully.
" Economic wash system
Using artificial intelligence, the washer uses minimum energy and water by selecting optimal water lever and washing time.
" Low noise system
The washer minimizes the washing and spinning noises by sensing the amount of laundry.
" Child-Lock
The Child-Lock system has been used to prevent children from pressing any button to change the program during operation.
" Nano-silver sterilization washing(Option)
By applying very fine silver particles on essential parts inside, the washer sterilizes up to 99.9% as is done by boiling wash.
" Air bubble washing(Option)
This is an advanced technology that generates millions of air bubbles inside the drum on washing sequence, and the bubbles dissolve the detergent particles completely and cleanse all the soil in clothes gently and neatly.
" Waist Care
Designed by the waist, and the most comfortable angle eject into the laundry is convenient and easy to manipulate.
" The World's First Steam White Course
The Steam White Course save more 50 percent of Electricity, Water, Time than previous White Course.
" The World's First
Shoes Course
Enable to wash shoes.
" Self-Cleaning
Course of Drum.
Enable to Self-Cleaning of Drum.
" Digital Condensing
Dry System.
Condensing Dry System with saveing energy. (for DWC-UD121X)
CONTENTS Page
2
PARTS AND FEATURES
The parts and features of your washer are illustrated on the page. Become familiar with all parts and features before using your washer.
Accessories
NOTE
The drawings in the book may vary from your washer model. They are designed to show the different features of all models coverd by this book, Your model may not include all features.
ADJUSTABLE LEG
CONTROL PANEL
DOOR
PUMP COVER
DETERGENT CASE
INLET HOSE
(HOT, OPTION)
INLET HOSE (COLD)
POWER CORD
HOSE DRAIN
Hose drain Inlet hose Spanner Manual Cap holder
3
Save these instructions
Your safety is important to us. To reduce the risk of fire, electrical shock, or injury when using your washer adhere to the following basic precautions.
Understanding your responsibilities
• Do not use chlorine bleach and ammonia or acid(such as vinegar or rust remover) in the same wash. Hazardous fumes can form.
• Unplug power supply cord before attempting to service your washer.
• Do not wash fiberglass material. Small particles can stick to fabrics washed in following loads and cause skin irritation.
• Do not spray water on the control panel of the washer. It could cause fire or an electric shock.
• In case of the dual valve model, if you connect only cold water inlet valve, while water temperature is selected as hot or warm, there can be water leakage from unconnected water inlet valve.
• This appliance must be grounded. To avoide electrical shock, use a metal pipe for the ground connection.
• Flammable fluids (dry-cleaning solvents, kerosene, gasoline, etc.) should not be used or stored in or near your washer. Do not add flammable fluids to your wash water.These substances give off vapors that can create a fire hazard or explosion.
• After starting a cycle, do not reach into the washer until all motions stop.
• Do not tamper with the controls.
• The appliance is not intended for use by young children or infirm persons without supervision.
• If the supply cord is damaged, it must be replaced by the manufacturer, or its service agent or a similarly qualified person in order to avoid a hazard.
• If the appliance is supplied from a cord extension set or electrical portable outlet device it should be positioned so that it is not subjected to splashing or ingress of moisture.
Please ...
• Have only a qualified person install, repair, or replace parts on washer.
• Maintain washer properly.
• Protect washer from the weather and keep it where the temperature will not fall below freezing.
• Do not install the washer at a place of extremely high humidity. It could cause an electric shock or a short circuit.
• Connect washer to the correct outlet, electrical supply, water supply, and drain supply.
WASHER SAFETY
Read all instructions before using your washer
4
Removing transit bolts
1. Before operating the washer, remove the transit bolts(4ea) along with the rubber.
• If the bolts are not removed, it may cause heavy vibration, noise and malfunction.
2. Unscrew the 4 bolts with the spanner supplied. Keep the 4 bolts and spanner for future use.
• Whenever the appliance is transported, the transit bolts must be refitted.
3. Close the holes with the cap holders supplied.
Location of washer
• Check location where the washer will be installed. Make sure you have everything necessary for correct installation.
• Do not place or store your washer below 0°C (32°F) to avoid any damage from freezing.
• Do not place or store laundry products on top of washer at any times.
• Install the washer on the horizontal solid floor.
If the washer is installed on an unsuitable floor, it could make considerable noise, vibrate severely and cause a malfunction. If the washer is not level, adjust leg up or down for horizontal installation.
• Ventilation openings must not be obstructed by carpeting when the washer is installed on a carpeted floor.
• Leave some space (right & left : 2cm, rear : 10cm).
• In case of built-in installation, the distance between top of the washer
and bottom of upper plate should be at least 3mm.
INSTALLATION INSTRUCTIONS
Laundry
Tub
Washer
approx.
2cm
Drain Hose
5
The washer should be connected to the water mains using new hose sets and old hose sets should not be reused. In using only one water tap or in case of only one water inlet valve, connect the inlet hose to the cold water inlet valve. Option : Be careful not to confuse hot water inlet and cold water inlet.
For Ordinary Tap
For Screw-Shaped Tap
INLET HOSE CONNECTION
1 Pull down the collar of the
inlet hose to separate it from the water tap adapter.
2 Loosen the four screws
properly in order to fit into water tap.
3 Fit the water tap adapter
into the water tap and tighten the four screws evenly while pushing up the adapter so that the rubber packing can stick to the water tap tightly.
4 Remove the tape, and
screw connector B into connect A tightly.
5 Connect the inlet hose to
the water tap adapter by pulling down the collar of the hose end.
6 Connect the inlet hose
adapter of the hose to the water inlet of the washer by turning it clockwise to be fixed tightly.
• Please check the rubber packing present inside the inlet hose adapter of the hose.
1 Connect the inlet hose to
the water tap by screwing the connector tightly.
2 Connect the connector-
inlet supplied if necessary.
3Connect the inlet hose
adapter to the water inlet of a washer and turn it to be fixed.
*Check the packing in the inlet
TAPE
Connector B
Connector A
Connector
Connector
Rubber Packing
Hose
Connector
Rubber Packing
Hose
Connector
inlet
Connector
6
ELECTRICAL REQUIREMENTS
• Electrical earth is required on this washer
• If it does not fit the outlet, have a proper outlet installed by a qualified electrician.
• Don’t earth to a gas pipe.
• Don’t change the power supply cord plug.
• Check with a qualified electrician if you are not sure the washer is properly earthed.
WARNING
Recommended earthing method
Electrical shock hazard : Failure to follow these instructions could result in death or serious injury.
For your personal safety, this washer must be earthed. This washer is equipped with a power supply cord ‘A’ having a earthing plug ‘B’. To minimize possible shock hazard, the cord must be plugged into a mating earthing­type wall receptacle ‘C’. If a mating wall receptacle is not available, it is the personal responsibility and obligation of the customer to have the proper earthed wall receptacle installed by a qualified electrician.
C
B A
Drain system
• Never forget to install drain hose before operating your washer.
• Open the packing box, and there is a drain hose inside the drum.
• Connect the drain hose to the drain outlet at the back side of the washer.
• Proper securing of the drain hose will protect the floor from damage due to water leakage.
• When the drain hose is too long, do not force it back into the washer. This will cause abnormal noise.
• For Pump Model Top of laundry tub must be at least 60cm high and no higher than 100cm For Pump Model of washer.
When installing the drain hose to tub(sink), secure it tightly with a string.
• For Non-Pump Model
If you need to extend drain hose, contact the sales agent, or service center.
Level adjustment
1 If the washer is installed on an unsuitable floor,
it could make considerable noise, vibrate and cause a malfunction.
contacting outlet
Connect the - type end of drain hose to the end of contacting outlet securely.
less than 1m
less than 10cm
Height of Length of
drain hose drain hose if the height of drain hose less than 10cm less than 1m is elevated in the middle If not the height of drain less than 3m hose is elevated in the middle
For extending the drain hose, the type of end of drain hose to be used is not "#" type, but "$" type.
7
OPERATING YOUR W ASHER
2 Adjust the level of washer using adjustable legs.
• Please check if there is any gap between the four adjustable legs and the floor.
• Turning adjustable legs by the enclosed spanner, adjust the level of washer and make it sure that there is no swaying of washer.
• After the adjustment is finished, turn the fixing nuts up tightly so that the washer maintains the adjustment.
3 Make it sure that the washer does not sway when you press
down the four corners of the washer's top plate.
adjustable leg
Fixing Nut
NOTE
There should be no swaying of washer and all the adjustable legs should stick to the floor closely.
To obtain the best washing results, you must operate your washer properly. This section gives you this important information.
• Close zippers, snaps, and hooks to avoid
snagging other items. Remove pin, buckles, and other hard objects to avoid scratching the washer interior.
• Empty pockets and pull them inside out.
• Turn down cuffs and turn synthetic knits inside out to avoid pilling.
• Tie strings and sashes to avoid tangling.
• Treat spots and stains. (See “Removing stains” on page 21)
Preparing clothes for washing
8
• Drop items into washer loosely. Items should move easily through wash water for best cleaning and wrinkle-free results.
• Load washer properly and select correct load size setting. Overloading and selecting a setting too small for the wash load can :
- Cause poor cleaning
- Increase wrinkling
- Create excessive lint
- Wear out items faster (because of pilling)
• Mix large and small items in each load. Load evenly to maintain washer balance. An unbalanced load can make the washer vibrate during spin.
• Reduce wash time when using a small load size setting. Load with only a few small items needs less wash time.
• Use a large load size setting to reduce wrinkling with permanent press clothes and some synthetic knits. These items should have more room to move in the water than heavy items. (towels, jeans)
Loading
1 Detergent case 2 Adding fabric softener
• If desired, add measured liquid fabric softener to the softener inlet.
• Pour liquid fabric softener into the dispenser using the amount recommended on the package.
• Do not exceed the maximum fill line. Overfilling can cause early dispensing of the fabric softener which could stain clothes.
• Do not open the detergent case when water is supplied.
• Avoid pouring fabric softener directly on the clothes.
Adding detergent
• Separate heavily soiled items from lightly soiled ones, even if they would normally be washed together.
• Separate dark colors from light colors, colorfast items from non-colorfast item.
Sorting
Soil (Heavy, Normal, Light) Separate clothes according to amount of soil. Color (White, Lignts, Darks) Separate white clothes from colored clothes. Lint (Lint producers, Collectors) Wash lint producers and lint collectors separately.
Main wash
Pre wash
Fabric softener
9
Press this switch to turn the power 'ON' or 'OFF'. Operation and temporary stop is repeated as it is pressed. When you want to change program in
operating; Press the 'Start/Pause' button % Select the program that you want to change % Press the 'Start/Pause' button again.
You can select the course you want and each lamp is turned on when that course is selected.
You can select the spin speed you want and each lamp is turned on when that course is selected.
It can be used to pre-engage time for wash from 1 hr to 12 hrs.
You can select the dry condition you want and each lamp is turned on when that course is selected.
If you want to open Door intensionally during operation, press the 'Start/Pause' button and press again 'Door unlock' button. In this case, signal will be appeared on PCB board, then you can open Door after cooling insideTub temperature and draining water, also no button functions except Power button.
It can be used to adjust water temperature according to types of the load to be washed. As this button is pressed, water temperature is selected by Cold
%
30°C %40°C %60°C %95°C.
You can select the wash course you want and each lamp is turned on when that course is selected. As this button is pressed, the wash course is selected by Soak
%
Prewash %Main Wash.
You can select the rinse time(s) you want and each lamp is turned on when that course is selected. As this button is pressed, the rinse time(s) is selected by '1'
%
'Add water' %'2' %'Add water' %...
...
%
'5' %'Add water' %'1'.
Use this function when you want to protect any accident occurring from handling of washer by a child. During an operation of washer, press 'SPIN' and 'DRY' buttons simultaneously during 3 second. If this mode will be set successfully, CHL and remain time will be showen on PCB board alternately. In Child Lock mode, no button functions except Power button. If you want to set this mode, press 'SPIN' and 'DRY' buttons simultaneously during 3 second. And if you want to release this mode, press 'SPIN' and 'DRY' buttons simultaneously again during 3 second. If you want to change to the desire program, while this mode is working;
1. Press 'SPIN' and 'DRY' buttons simultaneously again during 3 second.
2. Press the 'Start/Pause' button.
3. Select the desired program and press the 'Start/Pause' buttom again.
THE FUNCTION OF CONTROL PANEL (D WC-UD121X)
* The Child Lock will be cancelled when power is off.
Change the desired program
10
Press this switch to turn the power 'ON' or 'OFF'. Operation and temporary stop is repeated as it is pressed. When you want to change program in
operating; Press the 'Start/Pause' button % Select the program that you want to change % Press the 'Start/Pause' button again.
You can select the course you want and each lamp is turned on when that course is selected.
You can select the spin speed you want and each lamp is turned on when that course is selected.
It can be used to pre-engage time for wash from 1 hr to 12 hrs.
You can select the rinse+spin condition you want and each lamp is turned on when that course is
If you want to open Door intensionally during operation, press the 'Start/Pause' button and press again 'Door unlock' button. In this case, signal will be appeared on PCB board, then you can open Door after cooling insideTub temperature and draining water, also no button functions except Power button.
It can be used to adjust water temperature according to types of the load to be washed. As this button is pressed, water temperature is selected by Cold
%
30°C %40°C %60°C %95°C.
You can select the wash course you want and each lamp is turned on when that course is selected. As this button is pressed, the wash course is selected by Soak
%
Prewash %Main Wash.
You can select the rinse time(s) you want and each lamp is turned on when that course is selected. As this button is pressed, the rinse time(s) is selected by '1'
%
'Add water' %'2' %'Add water' %...
...
%
'5' %'Add water' %'1'.
Use this function when you want to protect any accident occurring from handling of washer by a child. During an operation of washer, press 'SPIN' and 'RINSE+SPIN' buttons simultaneously during 3 second. If this mode will be set successfully, CHL and remain time will be showen on PCB board alternately. In Child Lock mode, no button functions except Power button. If you want to set this mode, press 'SPIN' and 'RINSE+SPIN' buttons simultaneously during 3 second. And if you want to release this mode, press 'SPIN' and 'RINSE+SPIN' buttons simultaneously again during 3 second. If you want to change to the desire program, while this mode is working;
1. Press 'SPIN' and 'RINSE+SPIN' buttons simultaneously again during 3 second.
2. Press the 'Start/Pause' button.
3. Select the desired program and press the 'Start/Pause' buttom again.
THE FUNCTION OF CONTROL PANEL (D WD-UD121X)
* The Child Lock will be cancelled when power is off.
Change the desired program
11
WASHING PROGRAM
Program
Normal
Whites
Heavy Stain
Delicate
Blanket
Quick 30
Memory
Tub
Clean
Steam
Whites
Sports Shoes
Baby Care
Air Wash
(DWC-UD121X)
Fabric type
Colorfast garments (shirts, night dresses, pajamas,..) and lightly soiled white cottons(underwares,..)
First check whether laundry is machine washable.(white cotton, linen, towel and sheets..)
Heavy soiled clothes (blue-jean,climbing clothes, ruck sack, sports wear,...)
Delicated laundry easily damaged. (silk, curtains,..)
Blanket, curtains,..
Lightly soiled clothes and frequently washing clothes and small amount of clothes.
Use to memory program you want. Use to clean
(and dry for DWC-UD121X) the Tub and Drum.
enable to white(white cotton, linen, towel, shees..)
Only sports shoes
Baby Clothes
disinfect or deodorize
Proper Temp.
40°C (cold,30°C, 60°C)
95°C (fixed)
40°C (cold, 30°C, 60°C)
Cold (fixed, in order to prevent textile damage)
Cold (fixed, in order to prevent textile damage)
Cold (fixed)
Cold
40°
40°
40°
Cold
Default data
Wash: main wash Rinse: 2 Spin : Medium Temp.: 40°C
Wash: main wash Rinse: 3 Spin : Medium Temp.: 95°C
Wash: pre wash Rinse: 3 Spin : Medium Temp.: 40°C
Wash: main wash Rinse: 2 Spin: low Temp.: cold
Wash: main wash Rinse: 3 Spin : Medium Temp.: cold
Wash: main wash Rinse: 1 Spin : Medium Temp.: cold
Wash: soak Rinse: 2 Spin: low Temp.: cold Dry : Low Temp (DWC-UD121X)
Wash :main wash Rinse : 2 Spin : Medium Temp. : 40°C Steam: Strong
Wash :main wash Rinse : 2 Spin : low Temp. : 40°C Dry : Low Temp (DWC-UD121X)
Wash :main wash Rinse : 4 Spin : Medium Temp. : 40°C Steam : Strong
Dry
Maximum Load
Refer to
rating label
Refer to
rating label
Refer to
rating label
Refer to
rating label
Refer to
rating label
Less than 3 kg
without load.
Refer to rating
label
Refer to rating
label
Refer to rating
label
Refer to rating label
Loading...
+ 23 hidden pages