Page 1
Page 2
Table Of Contents
Important Safety Instructions ............................................................................. 1
Disc Information................................................................................................... 3
Front Panel ...........................................................................................................4
Rear Panel ............................................................................................................5
Remote Control .................................................................................................... 6
System Connections ...........................................................................................9
Connecting to Power Supply.................................................................................. 9
Connecting to External AV Signal Source .............................................................. 9
Connecting to External AV Signal Source(YPbPr) ............................................... 10
Connecting to External AV Signal Source(SCART) ............................................... 10
Connecting to Earphone ...................................................................................... 11
Connecting to PC................................................................................................. 12
Connecting to TV Antenna ................................................................................... 13
TV Function ........................................................................................................ 14
Preparations......................................................................................................... 14
Image Setting....................................................................................................... 14
Audio Setting........................................................................................................ 17
Timer Setting........................................................................................................ 18
Setup Setting .......................................................................................................18
TELETEXT Function ..........................................................................................23
NICAM Function ................................................................................................. 24
DVD Playback Operation................................................................................... 25
USB and SD/MS/MMC Card Function............................................................... 29
DVD System Setup............................................................................................. 30
Other Functions ................................................................................................. 38
External AV Input Function................................................................................... 38
Computer Screen Function .................................................................................. 38
Troubleshooting................................................................................................. 39
Specifications..................................................................................................... 40
Page 3
Important Safety Instructions
This symbol indicates that dangerous voltage instituting a risk of electric shock is
present within this unit.
This symbol indicates that there are important operation and maintenance
instructions in the literature accompanying the appliance.
Caution: use of any controls, adjustments, or procedures other than those specified herein may
result in hazardous radiation exposure.
Caution
1. The product contains a low-power device. In order to ensure the safety of the laser device, do
not remove any cover and attempt to repair the unit. If any service is needed, please contact
the distributor or its authorised service centre.
2. To reduce the risk of electric shock, do not remove the cover (back). No user-serviceable parts
inside. Refer servicing to qualified service personnel. Unplug the product from the wall outlet
before servicing or when it is unused for a long period of time.
3. The manufacturer will not be held responsible for the damage caused by any substitutions and
modification of the product without authorisation from the manufacturer’s or authorised service
agent.
WARNING
The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids,
such as vases, shall be placed on the apparatus.
Caution: Laser radiation when open. Do not stare into beam.
Copyright Protection
This product incorporates copyright protection technology that is protected by U.S. patents and
other intellectual property rights. Use of this copyright protection technology must be authorised by
Macrovision, and is intended for home and other limited viewing uses only unless otherwise
authorised by Macrovision. Reverse engineering or disassembly is prohibited.
The images in this manual are for reference only and may differ from your model.
- 1 -
Page 4
Important Safety Instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use near water.
6. Clean only with dry cloth.
7. Do not block any ventilation
openings. Maintain well ventilated conditions around the product. Do not put product on a bed,
sofa or anything that blocks ventilation. Install according to the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves or other
apparatus (including amplifiers) that produce heat.
9. Read, heed and follow all instructions to ensure correct and safe installation and
interconnection of the apparatus;
10. The apparatus shall not be exposed to dripping or splashing and that no objects filled with
liquids, such as vases, shall be placed on the apparatus.
11. The mains socket-outlet shall be installed near the apparatus and the mains plug shall remain
readily operable.
12. Protect the power cord from being walked on or pinched particularly at plugs, power sockets,
and the point where they exit from the apparatus.
13. Only use attachments/accessories specified by the manufacturer.
14. Use only with the stand, tripod, bracket, or table specified by the manufacturer, or sold with the
apparatus.
15. Unplug the apparatus during lightning storms or when unused for long periods of time.
16. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has
been damaged in any way, such as power-supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.
Note: Do not touch the colour TFT LCD screen directly by hand.
IMPORTANT FOR LASER PRODUCTS
1. CLASS 1 LASER PRODUCT
2. DANGER: Visible laser radiation when open and
interlock failed or defeated. Avoid direct exposure to beam.
3. CAUTION: Do not open the back cover. There are no
user serviceable parts inside the unit. Leave all servicing to
qualified service personnel.
- 2 -
Page 5
Disc Information
Discs Supported
DISC LOGO CONTENTS SIZE MAXIMUM TIME
133min(SS-SL)
242min(SS-DL)
266min(DS-SL)
484min(DS-DL)
DVD
Audio+Video
(active picture)
12cm
CD
JPEG Still high resolution 12cm
z The operating method of some DVD discs is specified by the software maker. Please refer to
the instruction manual of the disc.
z The unit will play most recordable (CD-R) or erasable (CD-RW) CDs, but playback of CD-R or
CD-RW discs created on a computer requires proper formatting and finalization of the disc for
audio playback. Some computers and/or software programs may not be capable of creating
compatible discs.
Audio 12cm 74min
About Disc Terms
Title
Generally, pictures or music compressed on a DVD are divided into several sections, “title”.
Chapter
The smaller section unit of pictures or music in a DVD under the title, usually one title is comprised
of one or more chapters and each of them is numbered for easy searching. But some discs may not
have a recording by chapter facility.
Track
A segment of picture or music on a CD. Each track is numbered for searching.
- 3 -
Page 6
Front Panel
Front View
1. Colour TFT screen
2. Speakers
3. Power Indicator
During normal operation, it is blue; In
standby mode, it is red.
4. Remote Sensor
5. SOURCE button
Press repeatedly to select input, choose
from: TV, SCART, COMPOSITE, S-VIDEO,
Component, VGA or DVD mode.
In setup menu, use the ENTER button for
the same function.
6. MENU button
Press to enter or exit the setup menu.
7. Pr
8. VOL ▲/▼ button
▲/▼ button
In TV mode, press to select channels.
In setup menu, use the ▲/▼ direction
buttons for the same function.
Press to increase or decrease the volume;
In setup menu, use the ◄/► direction
buttons for the same function.
9. PLAY button
Press to play the disc in DVD mode.
10. ■ STOP button
Press to stop disc playback.
11. Eject button
Press to eject the disc out.
12. Power button
Press to enter or exit the standby mode.
13. SD/MS/MMC Card Port
Insert the SD/MS/MMC card into the port.
14. Disc Tray Slot
Used to load disc.
15. Earphone Jack
When connected to earphone, the internal
speakers will automatically turn off.
16. USB Connecting Port
Connect the USB memory.
- 4 -
Page 7
Rear Panel
Open the back cover on the right side of the unit’s rear panel and you will see all jacks, as
shown below:
1. Y/Pb/Pr Input Jack
Connect the Y/Pb/Pr input source in
COMPONENT mode.
2. AV Input Jacks
In COMPOSITE mode, connect the
external video signal input source.
3. Y/Pb/Pr L/R Audio Input Jack
Connect the L/R audio input source in
COMPONENT mode.
4. S-VIDEO and COMPOSITE L/R Audio
Input Jack
The L/R audio input jacks can be used in
both S-VIDEO and COMPOSITE modes.
5. S-VIDEO Input Jack
Connect the S-VIDEO input source in
S-VIDEO mode.
6. SCART Input Jack
Connect the SCART input source in
SCART mode.
7. TV antenna Input Jack
Connect the external TV antenna input
source.
8. DC 12V Input Jack
Connect the car power adapter.
9. VGA Input Jack
Connect the VGA input source in VGA
mode.
10. PC AUDIO Input Jack
Connect the PC audio input source.
11. Power Supply Cord
- 5 -
Page 8
Remote Control
Remote Control Drawing
1. POWER button
Press to enter or exit standby mode.
2. TV button
Press to enter TV mode.
3. DVD button
Press to select DVD mode.
4. P.M button
Press to select the screen picture mode:
choose from User, Standard, Soft, Bright
or Shine.
5. S.M button
Press to select the sound mode: Choose
from User, Standard, Music, Movie or
Speech.
6. 0~9 Number buttons
Press to select numbers such as TV
channel.
7. FAV button
Press to access your favourite channel.
8. STEREO/AUDIO button
Press to change sound parameters when
receiving Nicam or Dual Audio Language
broadcasts in TV mode.
Press to select audio language or audio
track in DVD mode.
9. VOL+/- button
Press to increase or decrease the volume.
10. MUTE button
Press to turn on or off the speaker output.
11. EXIT button
Press to exit the setup menu.
12. Direction buttons (▲▼◄►)
In the setup menu, press the ▲▼ button to
select a desired item and press the ◄►
button to adjust or set.
13. ENTER button
Press to confirm your operation in setup
menu.
14. SOURCE button
Press repeatedly to select TV, SCART,
COMPOSITE, S-VIDEO, COMPONENT,
VGA or DVD mode.
15. PLAY button
Press to play a disc in DVD mode.
16. PAUSE button
In DVD mode, press to pause playback.
Press the PLAY button to resume
normal playback.
17. / button
Press to search backward or forward in
DVD mode.
In teletext mode, they are the teletext
colour buttons.
- 6 -
Page 9
Remote Control
18. TITLE button
During disc normal playback, press to go to
display the title menu.
In TV or SCART video mode, press to
display or close the teletext.
19. MENU button (under DVD mode)
Press to enter disc menu in DVD mode.
In teletext mode, press to disable teletext
display for page updates and press again
to resume.
20. SETUP button
In DVD mode press to open the setup
menu.
In Teletext mode, press to display P.100.
21. SLOW button
Press to activate slow playback function in
DVD mode.
In teletext mode, press once to display the
concealed information, such as solution of
riddles or puzzles; press again to remove
the riddles answers from the display.
22. VGA (PC) button
Press to enter VGA mode.
23. SCART button
Press to enter SCART mode.
24. DISPLAY button
Press to display the reference information
of the current program.
25. SET FAV button
Press to set the current channel as the
favourite channel.
26.
/+10 buttons
In TV mode, press to return to the channel
previously viewed.
In DVD mode, press to select numbers
greater than 10.
27. SCAN button
In TV mode, press to scan the programs
and press again to stop scanning.
28. PR▲/▼button
In TV mode, press to select channel.
29. SUBTITLE button
In DVD mode, press to select alternate
subtitle languages during playback of a
multiple language DVD disc.
30. MENU button
Press to enter or exit the setup menu.
31. SLEEP button
This feature allows you to set up sleep time
in TV mode. Press the button and then
press the ENTER button to activate this
function. Then press the ▲▼ direction
buttons to select the desired time to sleep.
32. Eject button
Press to eject the disc from the unit.
33.
■ STOP button
Press to stop disc playback in DVD mode.
34.
/ Next Skip button
Press to skip to the previous or next
chapter/track in DVD mode.
In teletext mode, they are the teletext
colour buttons.
35. REPEAT button
Press to repeat a chapter, track, title or all
program content in DVD mode.
In teletext mode, press to hold the current
page and press again to resume.
36.
ANGLE button
Press to select various camera angles (if
the DVD supports multiple camera angles)
in DVD mode.
In teletext mode, press the button first time
to double the size of teletext letters in the
upper half of the screen, second to double
the size of teletext letters in the lower half
of the screen and third to resume normal
status.
37.
CARD button
Press to shift among disc playback, USB
playback and SD/MS/MMC playback.
In teletext mode, press to select four
groups of 3-digit numbers that are
displayed in different colours at the bottom
of the screen. Press the colour buttons on
the remote control to select, then use the
number buttons to input the corresponding
number to display the page.
Repeat the above procedures for each
page to be stored, using a different colour
button each time.
38. GOTO button
Press to select the desired disc starting
time, title or chapter in DVD mode.
In TV mode, press to display the real clock
and press the EXIT button to exit.
- 7 -
Page 10
Remote Control
Preparation of Remote Control
Softly push the back cover to open the battery
compartment.
Insert two batteries (1.5V, size AAA), please
make sure the polarity matches the marks
inside the compartment.
Softly press the back cover to close it.
z Under normal use the battery will last for
six months.
z Take out battery when the remote is not in
use for a long time.
Using of Remote control
Point the remote control unit from no more than
about 7 metres from the remote control sensor
and within about 60 degrees of the front of the
unit.
• The operating distance may vary
depending on the brightness in the room.
Notes:
• Do not point bright lights directly at the
remote control sensor.
• Do not place objects between the remote
control unit and the remote control sensor.
• Do not use this remote control unit while
simultaneously operating the remote
control unit of any other equipment.
- 8 -
Page 11
System Connections
• Open the back cover on the right side of the unit’s rear panel.
• Do not connect the power cord until all other connections have been made.
• Ensure that you observe the colour code when connecting audio and video cables.
Connecting to Power Supply
Plug the power supply cord to the wall AC outlet.
Connecting to External AV Signal Source
Use the AV cables to connect the external AV signal source to the AV input jacks on the rear panel
of the unit.
Use a S-VIDEO cable (not supplied) to connect the external AV signal source to the S-VIDEO input
jack on the rear panel of the unit.
After connection, turn on the power of the unit and the external AV signal source and then press the
SOURCE button to select COMPOSITE or S-VIDEO mode.
Note: The L/R audio input jacks can be used in both COMPOSITE and S-VIDEO modes.
- 9 -
Page 12
System Connections
Connecting to External AV Signal Source（YPbPr）
Use red, green and blue component video cables and red and white audio cables. AV cables to
connect the external AV signal source to the Y/Pb/Pr input Jacks on the rear panel of the unit.
And the other end of the cables into the corresponding sockets on the TV (see below)
After connection, turn on the power of the unit and external AV signal source and then press the
SOURCE button to select COMPONENT mode.
N.B. Ensure the AV signal source is also switched to component video mode.
Connecting to External AV Signal Source（SCART）
Use a SCART cable (not supplied) to connect the external AV signal source to the SCART input
jacks on the rear panel of the unit.
After connection, turn on the power of the unit and external AV signal source and then press the
SOURCE button to select SCART mode.
- 10 -
Page 13
System Connections
Connecting to Earphones
Connect earphones (headphones) to the earphone jack on the rear panel of the unit for listening to
the audio output in seclusion.
◆ The internal speakers output will turn off automatically after the earphones have been
connected.
Note: Excessively loud volume could damage your hearing. Turn down the volume before you
connect the headphones and then raise the volume to a comfortable level.
- 11 -
Page 14
System Connections
Connecting to a PC
Follow the steps and the figure below to connect a PC to the unit:
1. Connect one end of the VGA cable to the VGA input jack on the right side of the unit’s rear
panel and the other to the PC.
2. Connect one end of the audio cables to the PC audio input jack on the right side of the unit’s
rear panel and the other to the PC audio output jack.
3. Set the PC’s resolution to 1024×768@60Hz.
After connection, turn on the unit and the PC and then press the SOURCE button to select VGA
mode.
- 12 -
Page 15
System Connections
Connecting to a TV Antenna
Connect TV signal input source from the aerial to the TV jack on the rear panel of the unit.
After connection, turn on the power of the unit. Then press the SOURCE button to select TV mode
and conduct program selection. You can follow the steps below to select channels:
However, if this is the first time the TV has been used, you must first search and store the
channels by following the steps on pages 19, 20, 21 and 22.
1. For 1~9 channel:
Press one of the number buttons to select the desired channel and wait several seconds and it
will go to the selected channel.
Or press the number buttons to select the desired channel and press the ENTER button to go to
the selected channel immediately.
Or press the number buttons to select channel 0X
immediately.
2. For 10~99 channel:
Press the number buttons to select channel XX
immediately.
* X is the channel number.
, and it will go to the selected channel
, and it will go to the selected channel
- 13 -
Page 16
TV Function
Preparations
1. After connection, press the POWER button to turn on the unit.
2. Press the SOURCE button to select TV mode and you can then conduct the following
operations:
Image Setting
Note: This item is only available when there is signal input.
Press the MENU button once to enter the setup
menu. Press the ▲▼ button to select Image and
press the ENTER button to enter the menu
shown on the right.
In the Image setup menu, press the ▲▼ button
to select the desired item. Press the MENU
button to return to the previous menu.
Scheme Setup
Press the ▲▼ button to select Scheme and
press the ENTER button to enter. Press the
▲▼ button to select the desired item and press
the ENTER button to confirm your selection.
Press the MENU button to return to the previous
menu.
Picture Setup
Press the ▲▼ button to select Picture and
press the ENTER button to enter. Press the
▲▼ button to select the desired item and press
the ENTER button to confirm your selection.
Press the MENU button to return to the previous
menu.
- 14 -
Page 17
TV Function
Brightness Setup
Press the ▲▼ button to select
Brightness and press the ◄►
button to adjust the value. Press
the MENU button to return to
the previous menu.
Contrast Setup
Press the ▲▼ button to select Contrast and press the ◄► button to adjust the value. Press the
MENU button to return to the previous menu.
Hue Setup
Press the ▲▼ button to select Hue and press the ◄► button to adjust the value. Press the MENU
button to return to the previous menu.
Note: This item is only available under NTSC TV signal mode.
Saturation Setup
Press the ▲▼ button to select Saturation and press the ◄► button to adjust the value. Press the
MENU button to return to the previous menu.
Sharpness Setup
Press the ▲▼ button to select Sharpness and press the ◄► button to adjust the value. Press the
MENU button to return to the previous menu.
Advanced Setup
Press the ▲▼ button to select Advanced and
press the ▲▼◄► direction button to move the
image. Press the MENU button to return to the
previous menu.
Note: This item is only available in DVD, VGA
and Component modes.
- 15 -
Page 18
TV Function
When the VGA signal is connected to the unit, the Advanced setup menu is as shown below:
Press the “▲▼” button to select the desired
item and press the “ENTER” button to enter it’s
setup menu. Press the “MENU” button to return
to the previous menu.
Auto Adjust:
If the monitor is not clear, you should carry out “Auto Adjust”.
Press the “▲▼” button to select “Auto Adjust” and press the “ENTER” button to enter it’s menu.
Press the “▲▼” button to select “Yes” to activate this function or “No” to cancel. Press the “MENU”
button to return to the previous menu.
Image Pos:
Press the “▲▼” button to select “Image Pos” and press the “ENTER” button to enter it’s menu.
Within the menu, press the “▲▼◄►” button to move the image. Press the “MENU” button to return
to the previous menu.
Phase:
Press the “▲▼” button to select “Phase” and press the “◄►” button to adjust the value. Press the
“MENU” button to return to the previous menu.
Clock:
Press the “▲▼” button to select “Clock” and press the “ENTER” button to enter it’s menu. Press
the “◄►” button to adjust the value. Press the “MENU” button to return to the previous menu.
Auto Colour:
Press the “▲▼” button to select “Auto Colour” and press the “ENTER” button to activate this
function. Press the “MENU” button to return to the previous menu.
sRGB:
Press the “▲▼” button to select “sRGB” and press the “ENTER” button to enter it’s menu. Press
the “▲▼” button to select “On” to activate this function or “Off” to cancel. Press the “MENU” button
to return to the previous menu.
- 16 -
Page 19
TV Function
Audio Setting
Press the MENU button once to enter the setup
menu. Press the ▲▼ button to select Audio and
press the ENTER button to enter the menu
shown on the right.
In the Audio setup menu, press the ▲▼ button
to select the desired item. Press the MENU
button to return to the previous menu.
Volume Setup
Press the ▲▼ button to select Volume and press the ◄► button to adjust the level. Press the
MENU button to return to the previous menu.
Bass Setup
Press the ▲▼button to select Bass and press the ◄► button to adjust the level. Press the MENU
button to return to the previous menu.
Treble Setup
Press the ▲▼button to select Treble and press the ◄► button to adjust the level. Press the
MENU button to return to the previous menu.
Balance Setup
Press the ▲▼ button to select Balance and press the ◄► button to adjust the level. Press the
MENU button to return to the previous menu.
Auto Volume Setup
Press the ▲▼ button to select Auto Volume and press the ENTER button to access the menu.
Press the ▲▼ button to select “On” or “Off” and press the ENTER button to confirm. Press the
MENU button to return to the previous menu.
- 17 -
Page 20
TV Function
Sound Mode Setup
Press the ▲▼ button to select Sound Mode and
press the ENTER button to enter. Press the ▲▼
button to select the desired item and then press
the ENTER button to confirm your selection.
Press the MENU button to return to the previous
menu.
Timer Setting
Press the MENU button once to enter the setup
menu. Press the ▲▼ button to select Timer
and press the ENTER button to enter the menu
shown on the right.
In the Timer setup menu, press the ▲▼ button
to select Off, 15Min, 30Min, 45Min, 60Min,
75Min, 90Min, 105Min or 120Min. Press the
MENU button to return to the previous menu.
Setup Setting
Press the MENU button once to enter the setup
menu. Press the ▲▼ button to select Setup
and press the ENTER button to enter the menu
as show on the right.
In the Setup menu, press the▲▼ button to
select the desired item. Press the MENU
button to return to the previous menu.
- 18 -
Page 21
TV Function
Tuner/Prog.
Press the ▲▼ button to select the
Tuner/Prog. and press the ENTER button
to enter the menu shown on the right. Press
the ▲▼ button to select the desired item.
Press the MENU button to return to the
previous menu.
Country
Press the ▲▼ button to select the
Country and press the ENTER button to
enter the menu shown on the right. Press
the ▲▼ button to select the desired
item. Press the MENU button to return to
the previous menu.
Auto Scan
Press the ▲▼ button to select the Auto Scan and press the ENTER button to start auto scan. The
screen will display as shown below:
Auto scan will take a few minutes, when the tuning operation is complete the unit will exit and
automatically memorise the programs in sequence.
If you want to cancel auto scanning, press the MENU button.
- 19 -
Page 22
TV Function
Prg Organizer
Press the ▲▼ button to select the
Prg Organizer and press the
ENTER button to enter the menu
shown on the right.
In the Prg Organizer setup menu,
press the ▲▼ button to select the
desired item. Press the MENU
button to return to the previous
menu.
Pr. Name
Press the ▲▼ button to select the Pr. Name and press the ENTER button to enter. Then press the
▲▼ button to select letters or press the number button to input numbers. Press the MENU button
to return to the previous menu.
Skip
Press the ▲▼ button to select Skip and press the ENTER button to activate or cancel this function.
Press the MENU button to return to the previous menu.
Swap
Press the ▲▼ button to select Swap from Pr. and press the ENTER button to enter. Press the
number buttons to select program number. Repeat the above operations to Swap To Pr. Then
Press the ▲▼ button to select Perform Swap and press the ENTER button to confirm.
Manual Install
Press the ▲▼ button to select the
Manual Install and press the
ENTER button to enter the menu
shown on the right.
In the Manual Install setup menu,
press the ▲▼ button to select the
desired item. Press the MENU
button to return to the previous
menu.
- 20 -
Page 23
TV Function
Search
Press the ▲▼ button to select Search and press the ► or ◄ button to start searching forward or
backward. Press the MENU button to return to the previous menu.
Colour System
Press the ▲▼ button to select Colour
System and press the ENTER button to
enter the setup, press the ▲▼ button to
select item. Press the MENU button to
return to the previous menu.
N.B. “PAL” is used in most of Europe
and the UK except France which uses
“SECAM”.
Sound System
Press the ▲▼ button to select Sound
System and press the ENTER button to
enter the setup, press the ▲▼ button to
select item. Press the MENU button to
return to the previous menu.
N.B. The sound system “B/G” is used in
Western Europe, “D/K” is used in Eastern
Europe, “I” is used in the UK and “L” & “L'”
is used in France.
Fine Tune
Press the ▲▼ button to select Fine Tune and press the ► or ◄ button to start fine tuning forward
or backward. Press the MENU button to return to the previous menu.
This feature allows for minor adjustments to the integrated electronic tuner’s ability to tune in weak
broadcast signals or where applicable solve minor irregularities in cable channel tuning parameters.
Pr NO
Press the ▲▼ button to select Pr NO and press the ENTER button to enter. Press the number
buttons to enter the channel number. Press the MENU button to return to the previous menu.
- 21 -
Page 24
TV Function
Store
Press the ▲▼ button to select Store and press the ENTER button to store the above operations.
Note: The “Pr NO” and “Store” items only function when the program is searched out.
Language
Press the ▲▼ button to select the Language on
screen display, press the ENTER button to enter
the setup, press the ▲▼ button to select item.
Press the MENU button to return to the previous
menu.
Factory Reset
Press the ▲▼ button to select the Factory Reset and press the ENTER button to enter. Press the
▲▼ button to select “Yes” or “No” and press the ENTER button to confirm. Press the MENU button
to return to the previous menu.
SCART Mode
Press the ▲▼ button to select SCART Mode and press the ENTER button to enter. Press the ▲▼
button to select “Auto” or “Manual” and press the ENTER button to confirm. Press the MENU button
to return to the previous menu.
N.B. The auto scart mode will allow external signal sources to switch their picture and sound to be
automatically produced on the screen, when the source product is switched on.
In manual mode, you will have to select scart mode yourself to receive external signal sources.
- 22 -
Page 25
Teletext Function
Teletext is an optional function, therefore only the sets with the teletext system can receive the
teletext broadcast.
Teletext is a free service broadcast by most TV stations which provides up-to-the-minute
information on news, weather, television programs, stock prices and many other topics.
The teletext decoder of this TV can support the SIMPLE and FASTEXT systems. SIMPLE (standard
teletext) consists of a number of pages which are selected by directly entering the corresponding
page number. FASTEXT is a more modern method allowing quick and easy selection of teletext
information. Because the teletext pages are colour coded along the bottom of the screen and are
selected by pressing the corresponding coloured button.
button
Press this button to display or close the teletext in TV or SCART video mode.
button
Press this button to disable teletext display and wait for page updates and press again to resume.
button
Press this button to select the index page.
button
Press this button once to display the concealed information, such as solution of riddles or puzzles;
press again to remove the riddles information from the display.
button
Press this button to hold the current page and press again to resume.
button
Press this button the first time to double the size of teletext letters in the upper half of the screen, a
second time to double the size of teletext letters in the lower half of the screen and a third time to
resume normal status.
button
Press this button to select four groups of 3-digit numbers that are displayed in different colours at
the bottom of the screen. Press the colour buttons on the remote control to select, then use the
number buttons to input the corresponding number to display the page.
Repeat the above procedures for each page to be stored, using a different colour button each time.
button
Press this button to display the real clock and press the EXIT button to exit.
- 23 -
Page 26
NICAM Function
The unit supports NICAM function when in TV mode.
Under NICAM TV broadcast:
1. When receiving stereo audio signals, press the STEREO/AUDIO button on the remote control
repeatedly to shift the sound tracks between Nicam Stereo and Mono and the screen will
show the corresponding display as shown below:
2. When receiving bilingual audio signals, press the STEREO/AUDIO button on the remote
control repeatedly to shift the sound tracks between Nicam I, Nicam II, Nicam I+II and Mono
and the screen will show the corresponding display as shown below:
3. When receiving mono audio signals, press the STEREO/AUDIO button on the remote control
repeatedly to shift the sound tracks between Nicam Mono and Mono and the screen will show
the corresponding display as shown below:
Under A2 TV broadcast:
1. When receiving stereo audio signals, press the STEREO/AUDIO button on the remote control
repeatedly to shift the sound tracks between Stereo and Mono and the screen will show the
corresponding display as shown below:
2. When receiving bilingual audio signals, press the STEREO/AUDIO button on the remote
control repeatedly to shift the sound tracks between I, II and I+II and the screen will show the
corresponding display as shown below:
3. When receiving mono audio signals, press the STEREO/AUDIO button on the remote control to
display sound track Mono on the screen.
- 24 -
Page 27
DVD Playback Operation
Preparation
1. Press the POWER button to turn on the unit. Press the SOURCE button and select DVD mode.
2. Holding the disc with its printed side outward vertically to the disc tray.
3. Slightly put the disc into the disc tray.
4. It will be drawn into the unit and load automatically.
Warning: Do not play poor quality discs that may damage the player’s lens.
DVD Playback
Region Code
DVD players and discs are coded by region. These regional codes must match the played discs. If
the codes don’t match, the disc cannot be played. This player’s default code is region 2.
Play
Press the PLAY button to start playback.
Stop
During playback, press the ■STOP button once to stop playback and press the PLAY button to
resume normal playback. Press the stop button twice repeatedly to stop playback completely.
Pause
During playback, press the PAUSE button to pause the playback. Press the PLAY button to
resume normal playback.
Previous and Next
Press the button to go to the next chapter. Press the button once to return to the beginning of
the current chapter or track; press it twice to go to the previous chapter.
- 25 -
Page 28
DVD Playback Operation
Fast Playback
During playback, press the or button to activate fast backward or forward playback. During
fast playback, press the PLAY button to resume normal playback.
SLOW
During playback, press the SLOW button to activate slow playback. During slow playback, press
the PLAY to resume normal playback.
Repeat
Use the REPEAT button repeatedly to repeat a chapter, title or all.
◆ Some discs do not support the repeat function.
Menu
Normally there is a selecting menu for DVD discs. You can press the MENU button (under DVD
mode) to enter the menu, and use the direction buttons to highlight an item. Then press the ENTER
button to confirm.
Title & Chapter
Normally there are several titles in a DVD disc, and several chapters (sections) in a title. You can
select any title or chapter quickly by entering the relevant number.
Language (Audio)
There can be up to 8 audio languages on a DVD disc. When you play a multi-language DVD disc
you can use press the AUDIO button on the remote control to select a language.
Subtitle
The DVD player can support multiple kinds of subtitles. When you play a multi-subtitle disc you can
press the SUBTITLE button on the remote control to select different subtitles.
GOTO
During DVD disc playback, press the GOTO button on the remote control once, there will be a
menu displayed on the screen. You can set or select items for your preference. Use the
buttons to select items and press the ENTER button to enter and use the buttons to select the
desired item. Press the direction button to return. When selecting the Title/Chapter, TT Time/CH
Time, use the number buttons to input the desired title/chapter number time.
◆ Some DVD discs do not support the search function.
Various Camera Angles
The movies on some discs have been recorded from various camera positions which can make you
enjoy the same scene from different perspectives. When playing a DVD containing various camera
angles the camera symbol appears on the screen. Press the ANGLE button repeatedly until the
desired perspective is shown. The picture will be adjusted in 1～2 seconds.
- 26 -
Page 29
DVD Playback Operation
CD Playback
The player will play all tracks on a CD disc by default. You can use the and (PREV/NEXT skip)
buttons, or number buttons to select a track.
Stop
Press the ■ STOP button once to stop playback and press the PLAY button to resume normal
playback. Press the STOP button twice repeatedly to stop playback completely and the unit will
return to the previous system mode.
Pause
Press the PAUSE button to pause the playback and then press the PAUSE button again or PLAY
button to resume normal playback.
Previous and Next
Press the button once to go the beginning of this track. Press twice repeatedly to go the previous
track.
Press the button to play from the beginning of the next track.
Fast Playback
Press the or FWD/REV SCAN button on the remote control to activate fast backward or
forward playback.
Repeat
Use the REPEAT button repeatedly to repeat Track, All or to cancel repeat.
◆ Some discs do not support the repeat function.
Audio
During CD playback, press the AUDIO button on the remote control to select the audio output mode:
Mono Left, Mono Right, Mix-Mono and Stereo.
Goto
Press the GOTO button to access the time-selected state. You can select Disc Go To, Track Go To
or Select Track respectively by pressing this button repeatedly. Use the 0-9 buttons to enter the
desired time and then the player will play according to the selected time.
- 27 -
Page 30
DVD Playback Operation
JPEG Playback
JPEG is a common picture format that requires small amounts of storage per image and has low
loss in resolution. Hundreds of pictures can be stored on a disc in this format. In order to view JPEG
photo albums, you can ask your film development company to make a ”PICTURE CD” when they
develop your film.
Normal Playback
Load a JPEG disc, there will be a root menu displayed on the screen. Use the ENTER button and
the direction button to select a submenu, and then use the ▲▼ direction button to select the
contents. Many discs have other contents besides pictures.
For Picture CD disc, it will display the pictures automatically.
During playback, press the or button to select the picture.
◆ Many discs have other contents besides pictures.
Stop
Press the STOP button to preview the pictures in thumb nail form. Press the PLAY button to
resume normal playback.
Pause
Press the PAUSE button to pause playback, press the PAUSE button again or PLAY button to
resume playback.
Repeat
During playback, press the REPEAT button repeatedly, and the repeat modes are Shuffle, Random,
Single, Repeat One, Repeat All and Repeat Off.
Previous and Next
During playback, press the or button to select picture.
Menu
Press the MENU button once to stop playback and return to the root menu.
GOTO
During playback, press the GOTO button on the remote control once, use the number buttons to
input the file number.
Picture Rotation
This can be used only when the picture is normally displayed. Once another picture is selected,
rotation will be cancelled automatically. Use the buttons to rotate the picture.
◆ Some JPEG disc’s may not support the rotating function.
- 28 -
Page 31
USB and SD/MS/MMC Card Function
Preparation:
1. Connect the unit to the power supply.
2. Press the POWER to turn on the unit.
3. Press the SOURCE button to select DVD mode.
4. Insert the USB memory into the unit’s USB slot, or insert the SD/MS/MMC card into the
SD/MS/MMC card slot on the right side of the unit. Please see the figure below:
¾ Make sure that files are stored in the USB memory and SD/MS/MMC card before connection.
5. Press the CARD button to select disc playback, USB playback or SD/MS/MMC playback. The
default state is disk playback. Please see the figure below:
6. Press the buttons to select the folder and press the ENTER button to enter.
7. Press the buttons to select the desired track. Then press the PLAY button to start
playback.
8. Press the STOP button to stop playback. Press the button to return to the folder menu.
Note:
1. The screen display will vary from disc to disc.
2. Pull out the USB memory or SD/MS/MMC card directly after the files are played. Then the unit
will return to the state of disc playback mode.
00:00 00:00
001/002
BAK
JPEG
- 29 -
Page 32
DVD System Setup
Preparations
1. Connect to the power supply and turn on the unit.
2. Press the SOURCE button to select DVD mode.
3. Press the SETUP button on the remote control to display the settings menu. The menu
includes General setup, Audio setup, Video setup, Preference and Password setup.
4. Press the button on the remote control to select a category. All the items in the category
will appear on the screen.
5. Press the SETUP button again to exit the setup.
General Setup Page
Press the SETUP button to enter the General Setup Page. The screen will display as the below:
TV Display
Angle Mark
1. In the menu, use the button to select the
desired item.
2. Press the ENTER button to enter the item.
3. Press the button to return.
1. Press the button to select TV Display.
2. Press the ENTER button to enter.
3. Use the button to select items.
4. Press the ENTER button again to confirm
selection and return to the previous menu.
1. Press the button to select Angle Mark.
2. Press the ENTER button to enter.
3. Use the button to select On or Off.
4. Press the ENTER button again to confirm
selection and return to the previous menu.
- 30 -
Page 33
DVD System Setup
OSD Lang
Captions
Screen Saver
Last Memory
1. Press the button to select OSD Lang.
2. Press the ENTER button to enter.
3. Use the button to select items.
4. Press the ENTER button again to confirm
selection and return to the previous menu.
1. Press the button to select Captions.
2. Press the ENTER button to enter.
3. Use the button to select items.
4. Press the ENTER button again to confirm
selection and return to the previous menu.
1. Press the button to select Screen Saver.
2. Press the ENTER button to enter.
3. Use the button to select On or Off.
4. Press the ENTER button again to confirm
selection and to return to the previous menu.
1. Press the button to select Last Memory.
2. Press the ENTER button to enter.
3. Use the button to select On or Off.
4. Press the ENTER button again to confirm
selection and return to the previous menu.
- 31 -
Page 34
DVD System Setup
Media Center
Audio Setup Page
Press the SETUP button to enter the General setup menu and then use the button to select
Audio Setup Page, the screen will display as the below:
Dolby Digital Setup
Dual Mono
1. Press the button to select Media Centre.
2. Press the ENTER button to enter.
3. Use the button to select DVD, USB,
SD/MMC or MS.
4. Press the ENTER button again to confirm
selection and return to the previous menu.
1. In the menu, use the button to select the
desired item.
2. Press the ENTER button to enter the item.
3. Press the button to return.
1. Press the button to select Dolby Digital.
2. Press the ENTER button to enter the setup, the
screen will display as left:
3. In the menu, use the button to select
items.
4. Press the ENTER button to enter the setup.
Press the button to return.
1. Press the button to select Dual Mono.
2. Press the ENTER button to enter.
3. Use the button to select items.
4. Press the ENTER button again to confirm
selection and return to the previous menu.
- 32 -
Page 35
DVD System Setup
Dynamic
HDCD Setup
On the Audio Setup Page, use the button to select HDCD Setup. Press the ENTER button to
enter the setup and the screen will display as below:
Video Setup
Press the SETUP button to enter General Setup Page and then use the button to select Video
Setup Page, the screen will display as below:
1. Press the button to select Dynamic.
2. Press the ENTER button to enter the setup, the
screen will display as left:
3. Press the ENTER button to enter.
4. Use the button to adjust.
5. Press the ENTER button again to confirm
setting and return.
6. Press the button to return.
1. In the menu, press the ENTER button to enter
the setup.
2. Use the button to select items.
3. Press the ENTER button again to confirm
selection and return.
4. Press the button to return.
1. In the menu, use the button to select the
desired item.
2. Press the ENTER button to enter the item.
3. Press the button to return.
- 33 -
Page 36
DVD System Setup
Video Quality Setup
Select Quality, press the ENTER button to enter the menu as below:
Sharpness
Brightness
Contrast
1. In the menu, use the button to select the
desired item.
2. Press the ENTER button to enter the item.
3. Press the button to return.
1. Press the button to select Sharpness.
2. Press the ENTER button to enter.
3. Use the button to select High, Medium or
Low.
4. Press the ENTER button again to confirm
selection and return to the previous menu.
1. Press the button to select Brightness.
2. Press the ENTER button to enter the setup, the
screen will display as left:
3. Use the button to adjust the level.
4. Press the ENTER button again to confirm
setting and return to the previous menu.
1. Press the button to select Contrast.
2. Press the ENTER button to enter the setup, the
screen will display as left:
3. Use the button to adjust the level.
4. Press the ENTER button again to confirm
setting and return to the previous menu.
- 34 -
Page 37
DVD System Setup
Preference Setup
Press the SETUP button to enter the General Setup Page and then use the button to select
Preference Page, the screen will display as the below:
Audio
Subtitle
Disc Menu
1. In the menu, use the button to select the
desired item.
2. Press the ENTER button to enter the item.
3. Press the button to return.
1. Press the button to select Audio.
2. Press the ENTER button to enter.
3. Press the button to select audio language.
4. Press the ENTER button again to confirm
setting and return to the previous menu.
1. Press the button to select Subtitle.
2. Press the ENTER button to enter.
3. Press the button to select subtitle
language.
4. Press the ENTER button again to confirm
setting and return to the previous menu.
1. Press the button to select Disc Menu.
2. Press the ENTER button to enter.
3. Press the button to select menu
language.
4. Press the ENTER button again to confirm
setting and return to the previous menu.
- 35 -
Page 38
DVD System Setup
Parental
Default
Password Setup
Press the SETUP button to enter Gerneral Setup Page and then use the button to select
Password Setup Page, the screen will display as the below:
DVD discs equipped with the child lock function are
rated according to their contents and settings vary
from disc to disc. Depending on the disc, you can
lock out playback of the disc altogether.
1. Press the button to select Parental.
2. Press the ENTER button to enter.
3. Press the button to select item.
4. Press the ENTER button again to confirm
setting, and you should enter the password.
The Default Password is 3308.
5. Press the ENTER button again to confirm
setting and return.
1. Press the button to select Default.
2. Press the ENTER button to select Reset.
3. Press the ENTER button, all the settings will
return to the default status.
1. In the menu, use the button to select the
desired item.
2. Press the ENTER button to enter the item.
3. Press the button to return.
- 36 -
Page 39
DVD System Setup
Password Mode
Password Change
1. Press the button to select Password
Mode.
2. Press the ENTER button to enter.
3. Press the button to select On or Off.
4. Press the ENTER button again to confirm
setting and return to the previous menu.
You can change the password by yourself.
1. Press the button to select Password.
2. Press the ENTER button to enter.
3. Press the ENTER button again to change the
password.
4. According to the indication on the menu, Use
the number buttons to input the old password,
then input the new password, then input again
to confirm. Press the ENTER button again to
confirm setting and return. The password has
been changed successfully.
5. The Default Password is 3308.
- 37 -
Page 40
Other Functions
External AV Input Function
The unit has an external AV input function. It supports SCART, COMPOSITE, S-VIDEO and
Component modes. Use the AV cables, SCART cable and S-Video cable to connect the unit to the
external AV signal source such as a DVD or VCR recorder, camcorder, satellite receiver or game
player etc. Then turn on the unit and the external AV signal source. Press the SOURCE button to
select the corresponding mode. Then you can go on to the set up the menu in a certain mode.
Computer Screen Function
The TFT LCD screen of the unit can be used as the a computer screen. Take the steps of
connecting the unit to the PC as shown on page 12 and then you can set up the menu.
Ensure you set the PC’s resolution to: 1024 x 768@60Hz.
The operations of these menus in SCART, COMPOSITE, S-VIDEO, Component and VGA
modes are the same with those in TV mode. Please refer to the introduction in “TV
Function”.
Note:
1. Only when there are signals, can the menus can appear and be set.
2. Some of these menus are not available in these modes.
- 38 -
Page 41
Troubleshooting
SYMPTOM CHECK ITEM
Make sure disc is loaded in.
Make sure disc is not loaded the wrong way round.
Make sure disc is not dirty or warped.
The player cannot play.
There is no sound.
LCD has no display
Cannot continue to play and
play a section repeatedly.
There is no picture or picture
jitters up and down Unsteady.
Make sure the player’s region code is the same as region
code of DVD disc.
Make sure water condensation has not occurred. If it occurs,
take out disc and leave the player on for at least one hour.
Make sure system connection is correct.
Make sure the sound setup of DVD disc is correct.
Make sure disc is not dirty or warped.
Clean or replace the disc.
Make sure the speakers are not muted.
In the TV mode, set the correct sound mode.
Make sure the unit is turned on and the connections are
correct.
Make sure the power adapter is correctly connected.
Make sure it is not in A-B or other repeat status.
Make sure disc is not dirty or damaged.
Check if the connections with the external AV signal source
are correct.
Correctly set the items in the picture menu.
Check if the video type input signal is not corresponding to
the unit.
Make sure the unit is turned on and in correct video type.
Make sure there are no obstructions between the remote
The remote control does not
work.
control and the player.
Make sure the remote control is pointing at the player.
Make sure batteries are inserted and the polarity is correct.
Make sure battery is not weak.
Other Notes:
Static or other external interference may cause the player to behave abnormally. If this occurs,
unplug the power-supply cord from the outlet and plug it in again to reset the player. If the problems
persist, then please disconnect the power and consult a qualified technician.
- 39 -
Page 42
Specifications
TFT-LCD Screen Size 15 inches
DVD Player DVD+/-RW, DVD+/-R, CD, CD-R, CD-RW, JPEG
MS, SD, MMC 3 in 1 Card reader and USB 1.0/2.0
Multi Media USB Memory Reader
VGA
Speaker Output 3W+3W
compatible
Max Volume up to 2GB
15 Pin, Analog RGB signal, 0.7Vp-p, 75Ωinput(VGA,
SVGA, XGA computer signal compatibility)
1024*768@60Hz
, 800*600@60Hz, 640*480@ 60Hz
Files supported in the USB
memory and MS/SD/MMC Card
Subtitle languages supported English, French, Spanish, German, Italian, etc.
Power
Power Consumption < 48 W
Dimension
Weight About 5.8 Kg
Ambient Temperature 10~45℃
JPEG, MPEG 2
AC100～240V，50/60Hz
DC 9.5~12V
388mm × 176mm × 372mm（LXWXD）
DESIGN AND SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE
Manufactured under license from Dolby Laboratories.
“Dolby” and the double-D symbol are trademarks of Dolby Laboratories.
Confidential unpublished works. © 1992 -1997 Dolby Laboratories, Inc.
All rights reserved.
If at any time in the future you should need to dispose of this product please note
that: Waste electrical products should not be disposed of with househould waste.
Please recycle where facilities exist. Check with your Local Authority or retailer for
recycling advice. (Waste Electrical and Electronic Equipment Directive)
- 40 -
Loading...