How it Works
Daewoo
Loading...
DSI-9200
Service Manual
76 pgs5.29 Mb0
User Manual
22 pgs6.71 Mb0

Daewoo DSI-9200 User Manual

Download
Digital Satellite Receiver & VCR Combo
Instruction manual
Model: DSI-9300/ DSI-9400
DSI-9100/ DSI-9200
P/N: 97P95600D0-1C
➠
1
PRECAUTIONS AND SAFETY
Precautions
• Read this booklet carefully.
• Make sure the rating of your household electricity supply matches that shown on the back of the VCR receiver.
• Read this page to help you set up and adjust your VCR receiver.
• Do not put the VCR receiver in a hot or humid place (to avoid the risk of fire and electric shock).
• Do not open the VCR receiver.
• Do not connect the VCR receiver to the power supply if you have just moved it from a cold environment to a warm room. This can lead to condensation inside the video which can seriously damage the video and cassettes. Wait around two hours to allow it to reach room temperature.
• Make sure the video is placed at least 10cm apart from other home appliances or obstacles to get sufficient ventilation.
• This apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on top of the video.
• Put the video on a steady, flat surface.
• Only clean the video with a soft, lint-free cloth. Do not use harsh or alcohol-based cleaning agents.
For your own safety!
• There are no components in this VCR receiver you can service or repair yourself.
• Do not open the case of the VCR receiver. Only allow a qualified engineer to repair or service your video.
• This VCR receiver is designed to work continuously. Switching it off (onto stand- by) does not disconnect it from the mains. To disconnect it from the mains, you have to unplug it.
AUTO SET
CH.
OP EJECT
➠
3
1
➠
2
CONTENTS
1 GENERAL INFORMATION
MAIN FEATURES_____________________ 3 FOR YOUR SAFETY ___________________ 4 UNPACKING ________________________ 4 GENERAL OPERATION _________________ 4 COMMON INTERFACE ________________ 5 FRONT PANEL _______________________ 5
2 INSTALLATION
CONNECTING TO ANTENNA ____________ 6 CONNECTING TO TV __________________6
1 USING RCA SUPPORT
2 USING RF SUPPORT (Optional function)
CONNECTING TO DIGITAL AMP
(Optional
function) ________________________ 8
MODES ___________________________ 9
CONNECTING YOUR VIDEO TO THE HI-FI SYSTEM, ANOTHER VIDEO OR CAMCORDER
_________ 10
CONNECTING YOUR VIDEO TO THE PERSONAL COMPUTER
_________________________ 11
3 VCR OPERATIONS
REMOTE CONTROL BUTTONS___________ 12 VCR FRONT PANEL BUTTONS __________ 14 VCR REAR PANEL BUTTONS ____________ 15
4 MENU SETUP MODE
INITIAL INSTALLATION _______________ 16 SatcoDX __________________________ 17 SETTOP___________________________ 18 MAIN MENU_______________________ 19
5 TUNING IN NEW STATIONS
CHANNEL SEARCH __________________ 20 SYSTEM SETTING
____________________ 22
6 PLAYING CASSETTES
PLAY ____________________________ 23 STILL ____________________________ 23 VARIABLE PICTURE SEARCH____________ 24 VARIABLE SLOW MOTION _____________ 24 FINDING NEW RECORDINGS (INDEX SCAN)
__ 24
CM SKIP (COMMERCIAL SKIP) __________ 24
7 RECORDING CASSETTES
TIMER RECORDING USING EPG _________ 25 SIMPLE RECORDING _________________ 26 ONE TOUCH RECORDING - OTR__________ 26 TIMER ___________________________ 27
8 NORMAL TIMER RECORDING
______ 28
9 VARIOUS MENU SETUP MODE
PARENTAL LOCK ____________________ 31 SYSTEM SETTING ___________________ 33 COMMON INTERFACE ________________ 33 FACTORY DEFAULT___________________33 EPG (ELECTRONIC PROGRAM GUIDE) ______34
10 TAPE CONTROL
_______________ 35
11 VCR FRONT PANEL INDICATIONS
__ 36
12 TROUBLE SHOOTING
___________ 38
13 TECHNICAL SPECIFICATION
_______ 40
Digital Satellite Receiver VCR is easy to use, and allows you to watch and record digital programs broadcasted via satellite. This instruction manual will guide you through the initial installation of your receiver.
It also describes how to take full advantage of a wide range of features that are easily accessible. Read this instruction manual carefully before installing your receiver VCR.
MAIN FEATURES
• High quality Digital Video & Audio
• Fully DVB compliant
• Common Interface with 2 PCMCIA slots
• User friendly and easy-to use menu system
• Various channel editing function, on Channel Management. (favorite, move, lock, rename, delete and sort)
• User programmable Satellite & Transponder information
• Automatic search for newly added transponder (NIT search)
• Stores up to 4000 channels
• Programmable Timer Recording :8 Events/1Month
• VISS (INDEX Search)
• LED Array Display
• OTR (Max. 10hrs/by 30min)
• Easy EPG recording
• Support software upgrading through RS-232C port
• Plug-and-play data transfer system (DSR to DSR)
• Individual channel volume saving function
• Timer function
• Automatic reserved channel moving system
• Electronic Program Guide (EPG)
• Teletext function support
• SCPC/MCPC receivable from C/Ku Band
• Multi LNB control by DiSEqC 1.0 and 22 KHz switching
• Motorized system control by DiSEqC 1.2* and USALS**.
• 256 color On-Screen-Display
• Support S/PDIF output (Optional function)
• satcoDX COMPATIBLE for auto program updating
* DiSEqCTMis a trademark of EUTELSAT.
** USALS
TM
is a trademark of Stab.
GENERAL INFORMATION
➠
5
GENERAL INFORMATION
1
➠
4
GENERAL INFORMATION
1
FOR YOUR SAFETY
• Allow clear space of more than 10 cm from the top, back and both sides for sufficient ventilation.
• Do not cover the Digital Satellite Receiver nor place it on a unit that emits heat.
• Use a soft cloth and a mild solution of washing liquid to clean the casing
• Do not connect or modify cables when Digital Satellite Receiver is plugged in.
• Do not remove the cover.
• Do not allow the unit to be exposed to extreme heat, cold or humidity.
• Never allow liquid spray or other materials to come into contact with the inside of the Digital Satellite Receiver.
• This Unit is designed for continuous operation. Switching it off does not disconnect it from the mains(Stand-by). To disconnect it from the mains, you have to unplug the mains.
UNPACKING
. 1 x Remote Control Unit (RCU) . 1 x RCA Cable . 2 x AAA battery (option)
. 1 x Instruction Manual . 1 x DSR
GENERAL OPERATION
Throughout this manual you will notice that the operation of your Digital Satellite Receiver VCR is based on a series of user friendly On Screen Display menus.
These menus will help you to get the most out of your Digital Satellite Receiver VCR and guide you through installation.
All function can be carried out by using the buttons on the remote control. The Digital Satellite Receiver VCR is easy to use, and adaptable for future upgrades. Note that new software may change the functionality. If you have difficulties with the operation of your Digital Satellite Receiver VCR, please refer to
the relevant section of this manual or call your dealer or customer service center for help.
EJECT
INPUT
TV / VCR
1
4
7
2
5
8
0
3
6
9
U
H F
M E
N U
V O
L
V O
L
C H / T
R K
+
C H /
T R
K
-
E
X I T
R E W
R E
C
S A
T
A U
D I O
I N
D E X
E
P G
F R E
E Z
E
S L O
W
+
I
N F O
T V /
R A D
I O
R E
C A
L L
3
0
S T
O P
F
F
S P
/ L P
P
L A
Y / P
A U
S E
P g
U P
P
g D O
W N
T E X
T
+
+
O
K
/
C
H
L
I
S
T
COMMON INTERFACE
You can watch scrambled programs by inserting right smart card into the right CAM (Conditional Access Module) and the CAM into the CI slot. You can see two CI slots when you open the front door of your receiver. CAM and smart card are not included in your Receiver. If you want to watch some scrambled programs, contact the broadcaster and he will inform you the needed CAM and smart card.
FRONT PANEL
2 CI Slot for conditional access module (CAM)
Changes the channel or moves to the previous/next item in the menu
Switches between the operational mode and stand-by mode
Opened Front Door
FRONT PANEL DISPLAY
. 1 x Aerial Cable
2
INSTALLATION
➠
7
2
INSTALLATION
➠
6
This section explains the connection of the Digital Satellite Receiver VCR with various Video devices. Refer to the manuals supplied with the equipment for the installation of outdoor equipment such as the Satellite dish. When adding a new equipment, be sure to refer to the related parts of the manual for the installation.
CONNECTING TO ANTENNA
CONNECTING TO TV
1
USING RCA SUPPORT
RS-232C
LNB. IN
S/PDIF
AUDIO
LINR
VIDEO
LNB. OUT
ANT
OUT
Satellite Receiver
Satellite Dish
RS-232C
LNB. IN
AUDIO
LINR
VIDEO
LNB. OUT
ANT
OUT
S/PDIF
TV
Satellite Receiver
RCA Cable
2 USING RF SUPPORT (Optional function)
Tuning procedure when RF connections are used
1 Select a channel number on the TV that is not currently used for other TV channels.
2 Follow the instructions in your TV manual to tune the TV channel selector to UHF channel
40.
3 If you are already using this channel, select another non occupied UHF channel between 21
to 69 on the TV. And then press the [UHF] button on this set’s remote control, you can see the default UHF channel number on the set’s front display.
4 Using the [up/down] button, you can change your set’s UHF channel. When you have
correctly changed the UHF channel number you will see the vertical lines. If there is interference from other channels, you can set the UHF channel number by pressing [OK] or [EXIT] button.
RS-232C
LNB. IN
AUDIO
LINR
VIDEO
LNB. OUT
ANT
OUT
S/PDIF
TV
Satellite Receiver
RF Cable
Satellite Dish
INSTALLATION
➠
9
2
INSTALLATION
➠
8
2
Digital AMP
Satellite Receiver
Optical Cable
CONNECTING TO DIGITAL AMP (Optional function)
MODES
There are two modes which you can operate the satellite receiver. The one is ‘Menu Setup Mode’ and the other is ‘General Viewing Mode’.
On ‘Menu Setup Mode’ you can setup your satellite receiver’s basic settings.
After you setup your satellite receiver properly on ‘Menu Setup Mode’, you can watch the programs on ‘General Viewing Mode’.
On ‘General Viewing Mode’ you can watch TV or listen the radio.
Also you can edit your channels using Sort function, setting favorite channels, Locking channels and so on.
VIDEO
ANT
OUT
AUDIO
LINR
S/PDIF
RS-232C
LNB. IN
LNB. OUT
2
INSTALLATION
➠
11
2
INSTALLATION
➠
10
Connecting your video to the personal Computer
RS-232C
LNB. IN
AUDIO
LINR
VIDEO
LNB. OUT
ANT
OUT
RS-232C
LNB. IN
AUDIO
LINR
VIDEO
LNB. OUT
ANT
OUT
Connecting your video to the hi-fi system, another video or camcorder
3
VCR OPERATIONS
Normally in VCR mode (“VCR” icon on the front panel lit), when your TV will show the VCR ’s choice of output.When in TV mode (“VCR” icon unlit) your TV will show its usual analogue channels. Use this to watch an analogue TV channel whilst your VCR is recording something different.
One Touch Record. Starts an OTR to record the current channel for 30 minutes. Each subsequent press adds 30 minutes to the recording time, to a maximum of 10 hours. Press STOP to end an OTR.
Slow-motion. When a tape is playing,this button cycles through the 6 possible slow-motion speeds.
Stop /Eject. Stops a tape or ejects it if already stopped.
Stop a tape while VCR is using.
Commercial Skip. Press then when a tape is playing to fast-forwards 30 seconds.
Rewind. Starts the tape rewinding or playing backwards. If already fast-backwards playing, each subsequent press of this button changes the play speed.
Play /Pause. Starts a tape playing, or pauses it (freeze frame) if already playing. IF One-Touch Recording, pressing this button pauses the recording. Press REC to resume.
Forwards Wind. Starts the tape forwards-winding to fast-forwards playing. If already fast-forward playing, each subsequent press of this button changes the play speed.
Programme Plus /Minus. Changes up or down a channel when viewing Digital Satellite CH. Also used for manual tracking when a tape is playing.
Audio /Video Source. Selects an external AV source when choosing a channel to watch or record.
➠
13
3
VCR OPERATIONS
Remote Control Buttons
➠
12
EJECT
INPUTMUTE
TV / VCR
1
4
7
2
5
8
0
3
6
9
UHF
MENU
VOL VOL
CH/TRK+
CH/TRK-
EXIT
REW
REC
SAT
AUDIO
INDEX
EPG
FREEZE
SLOW +
INFO
TV/RADIO
RECALL
30
STOP
FF
SP/LP
PLAY/PAUSE
Pg UP
Pg DOWN
TEXT
+
+
O
K
/
C
H
L
I
S
T
Display advanced information about current CH. Turns on or off the Tape Position information. Display advanced information about current CH in tape play or REC mode. Only the tape position itself is available when a tape is playing (see “Tape information display when playing a tape “ below) but more,including the tape length and free space is shown when the tape is stopped (see “Tape information display when not playing a tape ”).
Short Play /Long Play. Sets the mode for the next One-Touch Recording.
Index Plus (Intro Scan). This winds forwards through the tape, showing you a few seconds of each recording in turn. Press STOP or PLAY to end it.
Index Minus (Intro Scan Backwards). This winds backwards through the tape, showing you a few seconds of each recording in turn. Press STOP or PLAY to end it.
For fast navigation, the numbers can be used to enter and select channel numbers on ANY screens showing channel information. For two or three digit channels, press the buttons in succession.
Switches the system between standby and on.
Used for digital text applications. ‘Yes ’ &‘No’ are also used to answer on-screen questions.
Displays the programme guide.
Adjusts the volume, or moves to the left or right item in the menu.
Confirms choices in menus or displays programme list.
Clears on-screen information or closes an open menu.
Selects alternative audio sound.
Switches between the current and previously viewed channel. Also will exit a digital text application and return to normal viewing.
Get channel list from the selected satellite when the channel list is on.
Get access to the TV Guide (or Radio Guide) which provides information on the current and next programs on a channel.
Toggles TV/RADIO programme mode.
Get test signal of selecting UHF CH.
Display the main menu.
Mute the sound.
Pauses freeze frame if TV or Radio CH showing not playing.
3
VCR OPERATIONS
VCR Rear Panel Buttons
➠
15
3
VCR OPERATIONS
VCR Front Panel Buttons
The buttons on the front of the VCR have the same meanings as their equivalents on the remote control.
STANDBY/ON Switches the system between standby and on.
STOP/EJECT Stop /Eject. Stops a tape or ejects it if already stopped.
REC/OTR One Touch Record. Starts an OTR to record the current channel for 30
minutes. Each subsequent press adds 30 minutes to the recording time, to a maximum of 10 hours. Press STOP to end an OTR.
REW Rewind. Starts the tape rewinding or playing backwards. If already fast-
backwards playing, each subsequent press of this button changes the play speed.
PLAY/PAUSE Play /Pause. Starts a tape playing, or pauses it (freeze frame) if already
playing. IF One-Touch Recording, pressing this button pauses the recording. Press REC to resume.
FF Forwards Wind. Starts the tape forwards-winding to fast-forwards playing. If
already fast-forward playing, each subsequent press of this button changes the play speed.
➠
14
DSI-9100/ DSI-9300
DSI-9200/ DSI-9400
RS-232C
LNB. IN
S/PDIF
AUDIO
LINR
VIDEO
LNB. OUT
ANT
OUT
RS-232C
LNB. IN
AUDIO
IN
VIDEO
LNB. OUT
ANT
OUT
S/PDIF
DSI-9300/ DSI-9400
DSI-9100/ DSI-9200
LNB IN : Connect to Satellite Antenna
ANTENNA INPUT
Connect Video to a TV using RCA jack,
Connect Audio L/R to TV or Audio device
Connect to TV and VCR
using a RCA cable
RF OUTPUT
Serial : Connect to a PC for S/W upgrade
LNB OUT : Loop through
MENU SETUP MODE
➠
17
4
MENU SETUP MODE
➠
16
INITIAL INSTALLATION
1
When you turn on the Digital Satellite Receiver VCR for the first time, you can see “User Installation” menu at first.
During the installation process, the [OK] button always confirms a selection within these menus.
Or you can use [red] button to move to another installation step and [yellow] button to get detailed help for current process.
Use the [arrow] buttons to move up and down from one line to another.
2
Select your language.
3
Set up your local time.
After you complete setting up this menu, you can go to the “Channel Search” menu by pressing the [red] color button or press [exit] button to go to the main menu.
And you can choose your setup step.
Channel Search is the minimum setup process to watch the TV or Radio programs. So this precess must be done to watch any programs.
SatcoDX
This product supports the channel update function of SDX (SatcoDX Industry Standard Protocol) compatible product. This function enables users to download their own channel list from PC to settop box by the program called "World of Satellites" distributed by SatcoDX.
USERS MUST PREPARE FOR THE FOLLOWINGS TO DO THIS.
- Windows compatible PC with serial connection terminal(Com Port)
- 9 pin female to female Null-Modem serial cable
THIS FUNCTION CAN BE USED AS FOLLOWS;
(PC means its operation from PC and Settop means its operation from satellite receiver)
PC
1
Download and install "World of Satellites" from the homepage of SatcoDX (www. satcodx. com)
2
Run "World of Satellites" program after understanding its using method and connect the serial cable between PC and Settop Box.
3
Configure the channel list you want and choose "Program Receiver" menu and open "SatcoDX Receiver Programming Wizard" dialog. The dialog set-up is as follows;
Serial Port : The number of the port connected to serial cable
Baud Rate : 11520 Flow Control: None
4
➠
18
MENU SETUP MODEMENU SETUP MODE
➠
19
44
MAIN MENU
1
You can always change your menu settings on Main Menu easily.
2
You can check your receiver's version by pressing [red] color button on main menu.
At the ‘software Stand’, 4th and 5th digits express the Firmware Version. Likewise other products, higher number is the recent version.
SETTOP
1
Enter "User Installation" menu and press the [Green] button on remote control and open "SatcoDX Link" dialog.
Upon opening the dialog, Settop Box starts waiting the data transmission from PC and if this doesn’t occur after some time, it will inform the users of time out.
2
Click "Program Receiver" button to make the transmission started before the Settop dialog is Timeout.
3
If the data transmission is made in normal way, "SatcoDX Link" dialog will not be changed unless there is any transmission error. In case of transmission error or timeout, recheck the connection status of cable or PC set-up and restart the whole process from beginning.
4
If the data transmission is successfully made, "SatcoDX Link" dialog will display how many channels have been transmitted. The number of transmitted channel may be less than that in the channel list of PC and this is because Settop ignores the information on data channel and analog channel. When user push [OK] button and check if the data has been saved or not, all the satellite information and channel information seen before are deleted and its channel information will be restructured with the data transmitted through SatcoDX. If user wants to go back to the shipping status at the factory, "Factory Default" function can be used.
5
The channel information transmitted by using "World of Satellites" doesn’t include the detail set-up of each satellite. Therefore, user should enter "Channel Search" menu and change the LNB and DiSEqC set-up of each satellite appropriately and finally, check if transponder signal has been received or not by signal bar for the purpose of seeing its transmitted channel more conveniently.
5
TUNING IN NEW STATIONS
antenna position because the antenna will move according to the satellite position and your position.
5 SEARCH OPTION
This unit includes common interface function. So you cannot watch scrambled channels if you insert suitable cam module and smart card. If you may not want to search scrambled channels, you can skip the scrambled channels by checking [FTA Only] options on Channel Search option.
6 3-WAYS OF SEARCHING CHANNEL
If you choose [Search SAT], the receiver will search channels from the selected satellite on current menu.
If you choose [Search Multi-SAT], the receiver will search channels from the whole enabled satellite.
In case the satellite you want to receive is not on the sat­list, you can manually search by choosing [TP search].
Before you do the [TP search], check the frequency and symbol rate of the TP which you want to search channels from. On [TP search] process all we need are just the frequency and symbol rate. The satellite name is meaningless.
➠
21
5
TUNING IN NEW STATIONS
Channel Search
1 Before you search the channels you must choose at least
one satellite and enable it. Press [MENU] and select “Channel Search” with [SELECT].
2 Then choose the right LNB for the selected satellite. 3 In case you are using a dual LNB or two antennas
connected to a 22KHz tone switch, you can switch between both LNB or antennas by pressing the [red color] button of the remote control.
4 If you have installed Diseqc Motorized system, choose
the right one, move it to the right position following the instructions below.
DISEQC 1.2 :
If you want to move the antenna to the west or east position, press [left/right] button on your remote control on ‘Position’ menu, until you see the yellow signal strength bar. And set the position (press [OK] key). The position will be stored. Then you can load the saved antenna position after you changed the antenna position on other satellite antenna position setting.
USALS :
If you have USALS system, you have to input your position. And “send command” will move the antenna to the correct position. You don’t have to save the
➠
20
PLAYING CASSETTES
➠
23
5
TUNING IN NEW STATIONS
➠
22
6
SYSTEM SETTING
You can make misc settings on System Setting menu. “Start on channel” Feature allows you to setup the first
shown channel when you power on the satellite receiver.
Optional :
If your set has RF Output, you may show 2 additional menus related to RF channel selection.
Default UHF channel is 40.
Play
1 Push the cassette smoothly and squarely into
the cassette bay, with its windows pointing up.
2 Press [PLAY/PAUSE] to start playback. 3 Press [STOP] to stop playback. 4 Press [FF] or [REW] to fast forward or rewind the cassette from stop. 5 Press [STOP/EJECT] to eject the cassette in Stop mode.
• When you load a protected cassette such as pre-recorded film playback will start automatically.
• When you are playing tapes of poor quality or tapes which have been recorded on another machine, you can use the [PR+] or [PR-] buttons while the cassette is playing to reduce horizontal interferences stripes.
• Playing NTSC tapes on PAL TV: If you play cassettes which have been recorded on the NTSC colour system (as used in the USA), you can watch the pictures on most PAL TVs.
On older TVs, some black lines may appear at the top and bottom of the screen. The picture may also roll up or down. To prevent these problems adjust the V­HOLD knob on your television.
NTSC : National Television Systems Committee.
Still
1 Press [PLAY/PAUSE] in Playback mode to still picture from playback. 2 Press [PLAY/PAUSE] to switch back to normal playback.
• After approximately five minutes on still, the cassette will automatically switch to normal playback.
➠
25
➠
24
7
R
ECORDING CASSETTES
Timer recording using EPG
The Digital satellite receiver provides an automatic system which makes it easier to set the timer recording. EPG are shown in TV or Radio programme guides.
1 Insert an appropriate tape and position it correctly,
ready for recording. Press the [EPG] button and the EPG menu will appear.
2 Press the [GREEN] button to show VCR record
Timer set.
3 Press the [OK] or [RED] button to enter the Edit
Entry. The Channel, Date, Start and Stop time will then be filled in for the programme you have chosen.
4 If you wish to change any of the settings:
• Move the select bar to the setting you want to change using the [
…] or [†] buttons.
• Change the setting using the [œ] or [√] buttons,or the number buttons [0] to [9]. (For detailed descriptions of all the settings and how they can be changed, please see the Normal timer recording section.)
5 When all the settings are correct, select the [OK]
button. If you insert invalid data, you will see message box.
6 The Timer List screen will then be shown with your
new timer highlighted.
7 Press the [ ] button to put your video into standby.
Your video will not record unless you do this. You can switch the video on again if you want to set the timer to record another programme. Remember to put your
video back into standby when you have finished setting the timer.
• If the broadcasting station doen’t send the EPG data signal, there can be the channel without EPG data
6
PLAYING CASSETTES
Variable picture search
1 Keep pressing [FF] to vary the forward search speed. 2 Keep pressing [REW] to vary the rewind search speed.
Pressing the above buttons will vary the search speed in two speeds.
3 Press [PLAY] to switch back to normal playback.
Variable slow motion
1 Starting from playback you can keep pressing [SLOW-] or [SLOW+] to control slow
motion speed in six steps.
2 Press [PLAY] to switch back to normal playback.
Finding new recordings (index scan)
The video index search system allows you to find the beginning of any recording you have made on your video. Your video automatically records index marks on the tape whenever a recording is started.
1 Press [INDEX +] or [INDEX –] to search forwards or backwards.
The video will now wind to the beginning of a recording, play it for about 6 seconds, then wind on to the next one.
2 When you see the recording you want to watch, press [PLAY].
CM skip (commercial skip)
1 If you press [√√30] on the remote control during playback mode, tape advances for 30
seconds segment.
➠
27
➠
26
7
RECORDING CASSETTES
Recording cassettes
• If you want to use the video’s timer to record a programme, the clock, date and stations must be set correctly.
• Load a cassette with its safety tab in place and with enough free tape for the recording.
Simple recording
1 Load a cassette with its safety tab in place. 2 Press [PR+] or [PR-] to choose the station you want to record.
Press [SP/LP] if you wish to double the length of the cassette’s recording time. For example, on an E-240 cassette you can record for up to four hours when SP is
displayed, or up to eight hours when LP is displayed.
3 Press [REC] to start your recording. 4 Press [STOP] if you want to stop the recording for a short while. 5 Press [REC] to continue recording. 6 Press [STOP] to stop your recording.
One touch recording-OTR
1 Press [PR+] or [PR-] to choose the station you want to record. 2 Every time you press , the recording time will increase by 30 minutes. It is possible
to record for up to 10 hours if there is enough room on the cassette.
7
RECORDING CASSETTES
• If your timer list is full then you will not be able to set a new timer and a message will be shown. See Managing your timers for how to delete a timer to make space for a new timer.
• If you decide that you do not want to set a timer afterall you can press the [GREEN] button at any time.
• You can only set a timer up to approximately 1 month in advance.
• A timer cannot be longer than 12 hours in length.
TIMER
The "TIMER" menu allows you to program the timer in various ways.
The Digital Satellite Receiver VCR displays the time information given by the satellite. So there may be a slight difference between the actual time and the Digital Satellite Receiver's time.
1 EASY TIMER
To activate the Timer, set the "Enable" box to YES and enter the desired time.
Select Turn On Time and Turn Off Time, and the channel you want to view from the Turn On Channel.
2 ADVANCED TIMER
The advanced Timer allows you to program the various timer functions.
You can select the type of timer from Daily, Weekly, Monthly and One Time.
The “Turn On” Channel feature allows you to choose the channel with the set up timer. The receiver will show the channel, when it comes to the set up time.
➠
29
➠
28
8
NORMAL TIMER RECORDING
8
You can then change the settings as follows:
• Enable
- Press the [LEFT] or [RIGHT] button to select [YES] or [NO].
- Select [YES] allows you to timer recording.
• Record Channel
- Press the [UP] or [DOWN] button and then select channel to want timer recording.
- If you change to TV or Radio channel, press the [TV/RADIO] button in the channel list.
- You can press the [OK] button to see channel list.
- Or, you can enter a channel number directly by pressing the [0 ] to [9 ] buttons.
- Or, you can edit the channel number by pressing the [Green ] button. A flashing yellow cursor will be then shown. Pressing the [Up ] or [Down ] buttons will then change the channel number appropriately. Press the [Green ] button again to finish the edit.
- Or,you can press the [AV ] button to select an AV input. Each press of the button will pick the next input in turn.
• Date or Day
- You can press the [Right ] or [Select ] buttons to move the date on by one day. Press the [Left ] button to move the date back one day. Note, the day is shown next to the date for your information.
- Or, you can enter the day part of the date directly by pressing the [0] to [9 ] buttons. Note, the month and year are determined for you automatically.
- Or, you can edit the day part of the date by pressing the [Green ] button. A flashing yellow cursor will then be shown. Pressing the [Up ] or [Down ] buttons will then change the date appropriately. Press the [Green ] button again to finish the edit.
• Start Time / End Time
- You can press the [OK] button to move the time on by numeric keypad dialog.
- Or, you can enter the time directly by pressing the [0] to [9] buttons. Note, to enter 1.00am you must press ‘ 0100 ‘.
NORMAL TIMER RECORDING
Insert an appropriate tape and position it correctly, ready for recording.
In the menu select the [On/off timer & Record timer] and then [VCR record timer] to show VCR record timer set.
This screen lists all the timers that have been set. You may set up to a maximum of 8 timers.
If necessary, move the highlight bar using the [UP] and [DOWN] buttons until a timer slot with ‘select bar’ is highlighted.
Press the [RED] or [OK] button to take you to the TIMER SET screen.
The current date and time are shown at the top of the screen. You can select ENABLE, CHANNEL, OFTEN, DATE, DAY, START, END TIME and
TAPE SPEED.
Move the select bar to the setting you want to change using the [UP] or [DOWN] buttons.
➠
31
8
➠
30
VARIOUS MENU SETUP MODE
NORMAL TIMER RECORDING
9
PARENTAL LOCK
This function allows you to lock a channel with your password. In order to prevent your children or any other person from accessing these channels,
you can also protect your installed data and information using Install Lock.
1 HOW TO CHANGE THE PASSWORD
1) Enter the current password.
2) Select Parental Lock to ON to activate the function.
3) Enter a new password.
4) Confirm your new password by entering the new password again.
Note: Default password is 0000 Warning: Do not forget your password.
If you miss your password, you can use Masterkey (1250)
2 HOW TO USE PARENTAL LOCK
1) If you have activated the parental lock function, you must choose the channels you want to lock.
2) Press [OK], then the lock symbol will appear.
3) Exit from this menu, and press the [ ] button on the remote control or the front panel.
To activate the Parental Lock function, you must switch the Digital Satellite Receiver to stand-by mode at least once.
Turn on the Digital Satellite Receiver, and select a channel which is locked. To watch the channel, enter your password.
• Often
You can press the [Left ], [Right ] or [OK] buttons to change how often you want the timer to repeat. The choices are:
- Once : the timer will not repeat.
- Daily: the timer will repeat at the same time each day.
- Weekly: the timer will repeat on the same day of each week.
• Speed
You can press the [Left ] or [Right ] buttons to change what tape mode is used for you recording. The choices are:
- SP: your recording will be made using Standard Play.
- LP: your recording will be made using Long Play.
When all the settings are correct, select the [OK] button.
The TIMER LIST screen will then be shown with your new timer highlighted.
Press the [Standby] button to put your video into standby. Your video will not record unless you do this.
You can switch the video on again if you want to set the timer to record another programme. Remember to put your video back into standby when you have finished setting the timer.
➠
33
9
➠
32
VARIOUS MENU SETUP MODE
9
3 HOW TO USE INSTALL LOCK
1) Enter the current password.
2) If you select Parental Lock to ON, install Lock is changed to ON. (If you don’t want to set the Install Lock ‘ON’, you just change the Install Lock from ‘ON’ to ‘OFF’.)
3) Enter a new password. (If you do not want to change the password, skip step 3 and go to 5)
4) Confirm your new password by entering the new password again.
5) Exit from this menu, and press the [ ] button.
6) Turn on the Digital Satellite Receiver, and press the [MENU] button.
7) Select any menu, and press [OK].
8) The Enter Password box will appear.
9) Enter the password to access the menu.
VARIOUS MENU SETUP MODE
SYSTEM SETTING
You can make disc settings on System Setting menu. “Start on channel” Feature allows you to setup the first shown channel when you power on the satellite receiver.
Optional :
If your set has RF Output, you may show 2 additional menus related to RF channel selection. Default UHF channel is 40.
COMMON INTERFACE
You can see Slot A, Slot B and the types of the inserted CAM (Conditional Access Module). You can explore the sub-menu of the CAM by selecting the slot and pressing [OK] button. Each kind of CAM has its own sub menu. So, if you have any questions about the CAM sub-menu, contact your CAM provider.
FACTORY DEFAULT
The factory default menu will allow you to make the whole settings to the factory default mode, and will reboot the receiver. Just press [red] color button on your remote control. The whole settings and channels you searched before will be lost.
➠
35
9
➠
34
10
T
APE CONTROL
Tape Remain
If known, the tape length is minutes will be displayed to popup menu. (e.g. E240 for a 4 hour tape of E180 for a 3hour tape.) Also, amount of tape remaining will be shown in the form ‘hours: minutes: seconds’ and the current position of the tape will be indicated by selecting tape remain.
Go To Zero
To find the 0;00;00 counter position on the tape, select [Go to zero]
Counter Reset
You can reset the counter to 0;00;00 selecting [Counter Reset].
VARIOUS MENU SETUP MODE
EPG (ELECTRONIC PROGRAM GUIDE)
The Digital Satellite Receiver provides an EPG function for you to get access to the TV Guide (or Radio Guide) which provides information on the current and next programs on a channel.
To access to the EPG, press the [EPG] button on your remote control, and the EPG menu will appear.
If there is any EPG data, you can see the channel list on the left, the program schedule, and time will be displayed.
If you press [√] button, you will see the next EPG and the details if that exist.
If you press [œ] button, you will see the previous EPG. The time will be displayed in relation to the program
schedule. If there are detailed information for the schedule items,
you will see the message "Press 'OK' for Detailed info". Then press [OK] to see the detailed information.
➠
37
11
➠
36
VCR FRONT PANEL INDICATIONS
The six small icons on the left and right of the front panel indicate the following:
Tape inserted. Flashes as a tape is being ejected or if there is no tape or a write­protected tape inserted when a recording begins.
VCR mode (when lit)or TV mode (when unlit). Timer recording(s) programmed. Flashes if a timer recording cannot start because the
VCR is not in Standby. Long Play mode (when lit) or Short Play mode (when unlit). During tape playback this
shows the speed of the recording on tape. During recording this shows the speed of the recording. At other times this shows the speed selected for the next OTR.
Recording in progress.
The following will also appear on the front panel:
---- VCR is starting up. Please wait.
--:-- VCR ready for use. Please press [ ] on the remote control to start.
Clock VCR is in Standby and showing the current time. The display is dimmed to save
power.
STOP The tape has stopped.
EJCT The tape is ejecting.
PLAY The tape is playing. Flashes when auto-tracking is happening.
STILL The tape is playing and in Pause (freeze frame) mode.
SLOW The tape is playing and in slow-motion mode.
SCH The tape is playing fast-forwards.
SCH- The tape is playing backwards.
IND+ The tape is searching forwards for the next recording.
IND- The tape is searching backwards for the previous recording.
REC Recording in progress
RECP One-Touch Recording paused.
OTR Countdown One-Touch Recording time remaining in hours and minutes or minutes
and seconds.
ERR A tape or VCR mechanism fault has been detected. See the Troubleshooting Guide
for more help.
When you press any remote control button,you will see the a dot blink briefl that the VCR has seen the remote control command.
11
TAPE INFORMATION DISPLAY
TROUBLE SHOOTING
➠
39
12
➠
38
TROUBLE SHOOTING
There are interferences on your digital satellite channels, caused by an existing terrestrial channel or video signal.
The remote control is not working.
PROBLEM POSSIBLE CAUSES WHAT TO DO
The system is connected by RF leads and the output channel of the Digital Satellite Receiver is interfered with an existing terrestrial channels or video signal.
Battery is exhausted.
Remote control is incorrectly aimed.
Change the Digital Satellite Receiver output channel to a more suitable channel, or connect the system by SCART leads.
Change the batteries.
Aim the remote control at Digital Satellite Receiver, or check that nothing blocks the front panel.
VCR receiver does not seem to work / you can’t see the VCR receiver output on the TV set.
Are there any lights on the front panel?
No
• Make sure all leads are firmly connected to the VCR receiver and VCR/TV.
• Check there is power to the socket powering VCR receiver (and that it’s switched on).
• Check the fuse in the plug.
Yes
Is a VCR connected between VCR receiver and the TV? Ensure it is on and all leads are correctly attached.
• Try connecting VCR receiver directly to your TV set to see if your VCR is faulty..
• Check you have the correct channel selected on your TV set.
IF THE PROBLEM PERSISTS, PLEASE CONTACT YOUR DEALER OR SERVICE PROVIDER.
No sound or picture, and the front panel shows red light.
No sound or picture.
Bad picture / blocking error
No Welcome Menu on the screen after you switched on the Digital Satellite Receiver for the first time.
PROBLEM POSSIBLE CAUSES WHAT TO DO
The Digital Satellite Receiver is in stand-by mode.
The satellite dish is not pointing at the satellite.
No signal or weak signal.
The satellite dish is not pointing at the satellite.
Signal is too strong.
Satellite dish is too small.
LNB noise factor is too high.
The LNB is faulty.
The system is connected by SCART leads, and TV is not in AV mode.
The system is connected by RF leads.
Press the [stand-by] button.
Adjust the dish. Check the signal level in the Channel Search menu.
Check the cable connections, LNB, and other equipment connected between the LNB and the receiver, or adjust the dish.
Adjust the dish.
Connect a signal attenuator to the LNB input.
Change to a larger dish.
Change to an LNB with lower noise factor.
Change the LNB.
If the system is connected by SCART leads, switch the TV to the appropriate AV input.
Check the UHF channel fixed in your system and tune the UHF channel properly.
12
➠
40
13
T
ECHNICAL SPECIFICATION
TRANSMISSION STANDARDS
LNB/TUNER INPUT
SYSTEM RESOURCES
VIDEO DECODER
AUDIO DECODER
POWER SUPPLY
REAR PANEL INTERFACES
REMOCON TRANSMITTER
DVB, MPEG2
Connector IEC 169-24, Female-type Input Frequency 950 ~ 2150MHz Demodulation 2 Msps ~ 35Msps Code rate QPSK Max Current 500mA Supply Voltage 13V/18V DiSEqC 1.0, 1.2, USALS
Processor 32bit, 81 MHz RAM / ROM 8 MB / 2 MB
Video Standard ISO/IEC 13818-2(MPEG-2) Profile & Level Main Profile@Main Level Resolution 720 x 576 pixels for PAL Aspect ratio 4:3
Audio format MPEG Layer I and II Channel Mode Stereo, Mono Mode Audio Signal Sample Rate 32, 44.1, 48 Ksps Audio Signal bandwidth 15Hz ~ 20KHz Bit Resolution 24 bits PCM for the audio sample
Type SMPS Voltage & Frequency 110–240V~, 50/60Hz Power Consumption 23W
Video/Audio Output RCA Video Input RCA Optional Video Input/Output : RF modulator
Audio Output : RF modulator & S/PDIF Data In/Out Serial Jack (RS232) Satellite in IEC 169-24, Female, F-Type
Type VR-FA2A Operating Distance Straight : 8m, Pointing Angle (30°) : 7m Operating Life Time 200,000 Times Operating Without Load Batteries 2 x 1.5V AAA
R­40D(AAA)
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use