Daewoo DSC-3210EGB User Manual

1.62 Mb
Loading...

DSC-3210EGB

D

I

G

I

T

A

L

ADDITIONAL INFORMATION FOR TV'S SOLD IN GREAT BRITAIN

The appliance is supplied with a moulded three pin mains plug fitted with 5Amp fuse. Should the fuse require replacement, it must be replaced with a fuse rated at 5 amp and approved by ASTA or BSI to BS1362.

The plug contains a removable fuse cover that must be refitted when the fuse is replaced.In the event of the fuse cover being lost or damaged, the plug must not be used until a replacement cover has been obtained.Replacement fuse covers can be purchased from your nearest electrical dealer and must be the same colour as the original.

If the moulded mains plug is unsuitable for the socket outlet in your home or is removed for any other reasons, then the fuse should be removed and the cut off plug disposed of safely to prevent the hazard of electric shock.

There is a danger of electric shock if the cut off plug is inserted into any socket outlet. If a replacement plug is to be fitted, please observe the wiring code shown below.The wires in the mains lead are coloured in the accordance with the following code:

Blue-neutral Brown-live

As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows:

The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black.The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red.

Do not make any connections to the terminal in the plug which is marked by the letter E by the safety earth symbol or coloured green or green and yellow.

1

CONTENT

REMOTE CONTROL & TV CONNECTIONS

...............................................3

IMPORTANT SAFEGUARDS.......................................................................

4

INSTALLATION............................................................................................

4

START UP....................................................................................................

5

CONNECTING EXTERNAL EQUIPMENT...................................................

5

DAILY USE...................................................................................................

6

MENUS DESCRIPTION...............................................................................

8

TELETEXT..................................................................................................

11

2

REMOTE CONTROL & TV CONNECTIONS

LOCAL CONTROL

Front

Side

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

B1

 

 

 

 

 

 

B2

 

 

B3

B4

B5

B6

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

L

 

 

R

S-VIDEO

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

VIDEO

 

AUDIO

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

B7

B8

B9

 

B10

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

B1

MAIN POWER button

 

 

 

 

B6

REMOTE sensor

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

B2

PROGRAM UP/DOWN buttons

 

 

 

B7

VIDEO INPUT socket

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

B3

VOLUME UP/DOWN buttons

 

 

 

B8

AUDIO INPUT (L + R) socket

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

B4

TV / AV button

 

 

 

 

B9

PANEL S-VIDEO jack

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

B5

STAND-BY indicator

 

 

 

 

B10

HEADPHONE socket

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Rear

ANT

C3

C1

C2

 

 

 

 

 

 

 

 

 

AV1

AV2

 

 

C1

SCART 1 socket

 

 

 

 

 

C2

SCART 2 socket

 

 

 

 

 

C3

AERIAL jack

 

 

 

 

 

REMOTE CONTROL UNIT

 

 

 

 

 

TV mode

 

 

A2

A1

TELETEXT mode

 

 

 

 

 

A1

POWER

 

 

A13

A1

POWER

A2

SOUND MUTE

 

A3

A14

A2

SOUND MUTE

A3

NUMBER 0..9

 

A3

NUMBER 0..9

A4

SLEEP

 

 

A15

A4

.

A5

TV / AV

 

 

A5

.

A6

PROGRAM UP

 

 

A17

A6

PAGE UP

A7

(CURSOR UP)

 

 

A7

VOLUME DOWN

VOLUME DOWN

 

A4

A16

 

BRIGHT. DOWN

A8

(CURSOR LEFT)

 

A8

CANCEL

.

 

A6

A18

A9

PAGE HOLD

A9

.

 

A10

SUBPAGE

A10

.

 

A5

A19

A11

RED

A11

SKIP

 

A12

GREEN

A12

MOVE

 

A7

A20

A13

.

A13

3D(SOUND EFFECT)

 

A14

.

A14

MODE

 

 

A21

A15

.

A15

ZOOM

 

 

A16

.

A16

RECALL

 

A8

A22

A17

.

A17

NORMAL

 

A18

INDEX

A18

OK

 

A9

A23

A19

MENU

A19

MENU

 

 

VOL./ BRIGHT. SELECTION

A20

VOLUME UP

 

A10

A24

A20

VOLUME UP

A21

(CURSOR RIGHT)

 

 

BRIGHT. UP

PROGRAM DOWN

 

A11

A25

A21

PAGE DOWN

A22

(CURSOR DOWN)

 

A22

TELETEXT > TV

TV > TELETEXT

 

A12

A26

A23

HEIGHT

A23

.

 

A24

REVEAL

A24

.

 

 

 

A25

CYAN

A25

.

 

 

 

A26

YELLOW

A26

DELETE

 

 

 

 

 

3

IMPO RTAN T SAFEGU ARDS

WATER AND MOISTURE

Never install the set in the following places: In a wet basement, bathroom. Do not place any container with liquid on the set. Do not expose the set to dripping or splashing water.

HEAT

Never place the set near heat sources.

Never put a naked flame, such as a candle, on the top of TV set.

VENTILATION

Do not cover the ventilations openings in the cabinet and never place the set in a confined space such as in a bookcase or built-in cabinet unless proper ventilation is provided. Leave a minimum 10 cm gap all around the unit.

OBJECT ENTRY

Do not insert foreign objects, such as needles and coins, in the ventilation openings.

LIGHTNING STRIKING

You should disconnect the set from the mains and the aerial system during thunderstorms.

CLEANING

Unplug the set from the mains while cleaning.

AFTER MOVING THE SET

If the set is moved or turned, the MAIN POWER button must be switched off for at least 15 minutes in order to take out colour patches on the screen.

IN ST ALLAT IO N

Batteries

 

 

 

 

 

 

 

 

 

 

 

 

ANT IN

Open remote

 

 

 

 

 

Connect aerial to aerial jack (C3).

(at the rear)

 

 

 

 

 

 

batteries.

 

 

 

 

 

 

battery

 

 

 

 

 

 

D

I

G

I

T

A

L

on the TV set using front panel MAIN POWER button (B1). Select your preferred language from the LANGUAGE menu (see section START UP on page 5).

Press the remote control MENU button (A19) to enter the main menu. Select Install menu to tune and memorise TV programs.

4

START U P

LANGUAGE MENU

The very first time that you turn on the TV, the LANGUAGE menu will appear on the screen. Its purpose is to enable you to select the language that will be used for all the OSD (On Screen Display) menus. The user must enter a choice of language before proceeding further.

The language entered at this stage can still be modified at any later time, by entering the FEATURES menu (see later section under MENU DESCRIPTION). The discriptions used in the menu are those of the country code (e.g. GB = English, RUS = Russian etc).

LANGUAGE

CZ

D

DK

E

F

FIN

GB

GR

H

I

N

NL

PL

RO

RUS

S

SK

 

 

 

PR

MENU

Selection is made by use of the remote control CURSOR UP (A6)) / CURSOR

DOWN (A21) keys and CURSOR RIGHT (A20) / LEFT (A7) keys.

Once you are satisfied with your selection, push the OK button (A18) to confirm

PR

your choice, after which the menu will disappear. The menu will never appear

again.

 

C

IPMEN T

The rear Scart 1 (C1),

sockets to connect audio-video equipment.

Rear

ANT IN

REAR SCART 1 SOCKET (AV1)

This socket (C1) has video / audio inputs and outputs. It is recommended to connect to this socket automatic AV switching equipment such as pay-TV decoders, video games, DVD players and most VCRÕs.

In most cases, when connecting powered equipment to this socket, the TV set switches automatically to AV mode. If not, then use the TV/AV buttons (A5) or(B4) to select AV1.

REAR SCART 2 SOCKET (AV2)

This socket (C2) has video / audio inputs and outputs. Automatic AV switching equipment (for example most VCR connected to this socket.

In most cases, when connecting powered equipment to this TV set switches automatically to AV mode. If not, then use buttons (A5) or (B4) to select AV2.

You can also receive an S-VHS signal with REAR SCART2 selecting SVHS2 with the TV / AV buttons (A5) or (B4).

Side

ANT IN

VCR / DVD / Video Game / Pay-TV decoder

Important: If your video equipment does not have SCART socket(s),

or if you wish to use only the aerial (RF) connection (not recommended), then you should make use of PR 00 on the TV set for best performance.

HEADPHONE SOCKET

To hear TV sound with headphones, insert a 3.5mm headphone plug into the headphone socket (B10). The speakerÕs sound will be automatically cut off.

SIDE AV SOCKET (AV3)

 

 

 

VIDEO GAME

 

 

 

 

SIDE S-VIDEO JACK

 

 

 

 

The side AV socket (B7) -

 

 

 

 

The side S-VIDEO jack (B9) has

 

 

 

 

 

video inputs only. It is necessary to

(B8) has audio and video

 

 

 

 

 

 

OR

 

connect the audio inputs to socket

inputs. To switch from TV

 

 

 

 

 

 

(B8) in order to have audio and video.

to these inputs, use the TV

 

 

 

 

 

 

 

 

To switch from TV to these inputs, use

/ AV buttons (A5) or (B4)

 

 

 

 

 

 

 

 

the TV / AV buttons (A5) or (B4) and

and select AV3.

CAMCORDER

 

 

 

 

select SVHS3.

 

 

 

 

 

TV/AV SELECTION

Allows to switch between TV and external modes.

By repeatedly pressing the remote control TV / AV (A5) or the TV front panel TV / AV (B4) button, the onscreen display is changed as shown

AV1 > AV2 > SVHS2 > AV3 > SVHS3 > TV

5

DAILY USE

SWITCHING ON TV SET

1) If stand-by indicator (B5) is red, then the TV set is in stand-by mode.

You can switch on using the remote control POWER button (A1), the NUMBER 0É.9 buttons (A3), or PROGRAM UP (A6) / DOWN (A21) buttons. The front panel PROGRAM UP/DOWN buttons (B2) can also be used.

Once on, the stand-by indicator turns to green and the picture appears on the screen.

2) If stand-by indicator (B5) is not lit, then the TV set is powered off.

You must press the TV set front panel MAIN POWER button (B1). If a picture does not appear, then the stand-by indicator will be red. In this case, use the remote control as indicated in 1).

PR

MENU

PR

3) If stand-by indicator (B5) is flashing red, and green then the TV set is in child-lock mode.

It is necessary to use the remote control POWER button (A1), NUMBER 0É.9 buttons (A3), or PROGRAM UP (A6) / DOWN (A21) buttons. The front panel PROGRAM UP/DOWN buttons (B2) will not function.

Once on, the stand-by indicator turns to green and the picture appears on the screen.

 

1) By pressing the remote control

2) Pressing the TV set front panel

SWITCHING OFF

POWER button (A1) ,you can

MAIN POWER button (B1), you

switch off to stand-by mode (low

can completely power off the TV

TV SET

power consumption mode) which

set. In this case, you must use the

also allows quick restart by remote

same front panel POWER button

 

control (see above: SWITCHING

(B1) to switch on again (see

 

ON TV SET).

above: SWITCHING ON TV SET).

Remark: If a broadcast signal is not present after 30 minutes, the TV set will be automatically turned to stand-by mode.

PROGRAM SELECTION (FROM 0 TO 99)

Direct selection

Use the remote control NUMBER 0É.9 buttons (A3).

For two digits program numbers, enter the second digit within 2 seconds.

Up / Down selection

Use the remote control PROGRAM UP (A6) / DOWN (A21) buttons or the TV set front panel

PROGRAM UP / DOWN buttons (B2).

SOUND CONTROL

Volume adjustment

 

 

 

Use the remote control VOLUME UP

MENU

(A20) / DOWN (A7) buttons or the TV set

 

 

 

front panel VOLUME UP / DOWN

 

 

 

buttons (B3).

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Mute

Mute the sound by pressing the remote control SOUND MUTE button (A2).

Then, logo is displayed. The previous sound setting is returned after pressing the same button a second time.

Mono forcing, dual language

- If you are unable to get good sound quality for a program due to poor reception, you can force a change from stereo to mono transmission by pressing the remote control MODE button (A14). Then the program status display indicates "MONO" (in red).

-On the other hand, during a program with dual language transmission, the MODE button (A14) allows you to toggle between the first and second language. The program status display will indicate "DUAL 1" or "DUAL 2" (plus NICAM according to the received signal).

-To return to initial state, press again the MODE button (A14).

Sound effects

A SPATIAL sound effect is available, using the remote control 3D (A13) button.

The following display appears:

SPATIAL

 

Spatial sound effect

 

Sound transmission mode

STEREO

 

11:11

 

 

Clock

 

 

To return to initial sound effect, press again the 3D (A13) button.

The following display appears:

OFF

 

No sound effect

 

Sound transmission mode

STEREO

 

11:11

 

 

Clock

 

 

As an option, the sound effects PANORAMA, and VIRTUAL DOLBY are available with the same button.

For other adjustments (balance, equalizer, bass, treble), use the Sound menu (page8).

6