Daewoo DLN-20D3SHS User Manual

LCD TELEVISION

INSTRUCTION MANUAL

DLN-15D3AHS DLN-17D3AHS DLN-20D3AHS DLN-15D3SHS DLN-17D3SHS DLN-20D3SHS

P/N : 48586110E21V-R0

Important

Information

OUTDOOR USER MARKING

WARNING : To reduce the risk of fire or electric shock hazard, do not expose this appliance to rain or

moisture.

WET LOCATION MARKING

“Apparatus shall not be exposed to dripping or splashing and no objects filled with lipuids, such as vases, shall be placed on the apparatus.”

Service Instructions

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK)

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk electric shock.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and servicing instructions in the literature accompanying the appliance.

Important Information

FCC RF INTERFERENCE STATEMENT

NOTE : This equipment has been tested and found to comply with the limit for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If these equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measure.

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Correct the equipment into an outlet on a circuit different from that to which the receiver is

connected.

• Consult the dealer or an experienced radio, TV technical for help.

• Only shielded interface cable should be used.

WARNING : FCC regulations state that any unauthorized changes or modifications to this equipment not

expressly approved by the manufacturer could void the user’s authority to operate this equipment. U.S.A. ONLY

Note to CATV system installer : This reminder is provided to call the CATV system installer’s attention to

Article 820-40 of the National Electrical Code that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.

This product utilizes tin-lead solder, and fluorescent lamp containing a small amount of mercury. Disposal of these materials may be regulated due to environmental considerations. For disposal or recycling information, please contact your local authorities or the Electronic Industries Alliance : www.eia.org

Safety

Precautions

1. CLEANING

Unplug this TV equipment from the AC power outlet before cleaning. Do not use liquid cleaner or aerosol cleaners. Use a soft and damp cloth for cleaning.

2. ATTACHMENTS

Do not use attachments not recommended by the TV equipment manufacturer as they may result in the risk of fire, electric shock or other injury.

3. WATER AND MOISTURE

Do not place this TV equipment near water, for example, near bathtub, kitchen sink, laundry tub, in a wet basement, or near a swimming pool, or the like.

4. HEAT

Keep the TV equipment away from the heat sources such as radiator, heater, stoves and other heat-generating products.

5. SETTING

Do not place this TV on unstable cart, stand, or table. Placing the TV on an unstable base can cause the TV to fall, resulting in serious personal injuries as well as damage to the TV. Use only a cart, stand, bracket or table recommended by the manufacturer or salesperson.

6. WALL OR CEILING MOUNTING

When mounting the product on a wall or ceiling, be sure to install the product using the designated mounting tool according to the method recommended by the manufacturer.

7. POWER

This TV equipment should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supplied to your home, consult your TV dealer or local power company.

8. PIXEL

The LCD panel is a very high technology product with 2,359,296(15") 2,949,120(17”) 1,440,000(20”) thin film transistors which give you fine picture details. Occasionally, a few non-active pixels may appear on the screen as a fixed point of blue, green or red please note that this does not affect the performance of your product.

9. SET MOVING

When moving the product, place your fingers of one hand in the socket on the back of the TV and support the front of the TV with the other hand.

SAFETY PRECAUTIONS

Contents

IMPORTANT INFORMATION 2 SAFETY PRECAUTIONS 4 IMPORTANT SAFEGUARDS 6 SUPPLIED ACCESSORIES 7 FUNCTIONAL OVERVIEW 8

Front (Control panel) 8 Remote Controller 9

PREPARATION 10

Inserting Batteries into the Remote Control Unit 10 Mains Connection 10

CONNECTIONS 11

Antenna Connection 11 Connecting External Equipment 14

BASIC OPERATIONS 16

Switching On / Off 16 TV/AV Mode Selection 16 Volume Control 17 Channel Selection 17

MENU ADJUSTMENT 18

Channel Adjustment 18 Picture Adjustment 19 Sound Adjustment 20 PC Adjustment 21 Utilities Adjustment 23

WALL/ARM MOUNTING 27 TROUBLE SHOOTING 28 SPECIFICATIONS 30

Important

Safeguards

Location

Heat, Moisture, Dust, Vibration

Position your set so that bright light or sunlight doesn't fall directly onto the screen. Care should be taken not to expose the set to any unnecessary vibration, moisture, dust or heat. Do not expose the set to dripping or splashing.

Ventilation

Also ensure that the set is placed in a position to allow a free flow of air. Do not cover the ventilation openings on the back cover. Leave at least 10 cm around each side of the TV set.

Mounting

This set can be positioned by using the table top stand or wall mounting bracket. When you install the set using the wall mounting bracket, fix it carefully so it is secure.

Object Entry

Do not insert foreign objects, such as needles and coins, into the ventilation openings.

Lightning striking

You should disconnect your set from the mains and the aerial system during thunderstorms.

Cleaning

Unplug the set from the mains before cleaning. Dust the set by wiping the LCD screen and the cabinet with a soft, clean cloth. If the screen requires additional cleaning, use a clean, damp cloth. Do not use liquid cleaners or aerosol cleaners.

Do not rub or strike the LCD with anything hard as this may scratch, or damage the LCD permanently.

Service

Never remove the back cover of the set as this can expose you to high voltage and other hazards. If the set does not operate properly,unplug it and call your dealer.

Supplied Accessories

Make sure that the following accessories are provided with the product.

AC cord

AC/DC adapter

123

456

789

PICTURE MODE

SOUND MODE

DISPLAY MTS

COMPONENT

POWER

MUTE

VOL VOL

PREV. CH

CAPTION

SLEEP

TV/CABLEADD/DEL

ASPECT

100

Remote controller

Batteries (Option)

(2x1.5V, AAA)

Instruction manual

Functional

Overview

Front (Control panel)

Remote

sensor

LED

indicator

STAND-BY

ON/OFF CH VOL

TV/VIDEO

Power

On/OffCHUp/Down

Volume

Up/Down

TV/VIDEO

LED Indicator : Lights up red in Stand-By mode and Lights up green in TV on mode. Remote Sensor : Receives signals from the remote controller. Power On/Off Button : Use this button to power on/off. CH Up/Down Buttons : Use these buttons to change channels on your TV or to move the cursor in the menu. VOL Up/Down Buttons : Use these buttons to change your TV’s volume or to move the cursor in the menu. TV/VIDEO Button : Each time you press the TV/VIDEO button, the TV will cycle through:

TV / AV / S-VIDEO / COMPONENT 1 / COMPONENT 2 / PC

MENU Button : Use this button to enter and exit the MENU.

Functional Overview

Remote Controller

1. MUTE : Press this button, and the sound goes off. Press again,

and the sound returns.

2. POWER : Power on/off button in Stand-By mode.

3. CH : Change channels on your TV or move the cursor (up/down)

in the menu.

4. VOL : Adjust the volume or move the cursor (left/right) in the menu.

5. MENU : Menu display button.

6. DISPLAY : Display the current channel number and broadcasting

sound mode, or the external mode.

7. MTS (Multi CH TV Sound) : You can select sound mode in Mono,

Stereo, SAP (Second Audio Program). Choose the sound mode you want. It works only in TV mode.

8. TV : Select TV input mode.

9. AV : Select AV / S-VIDEO input mode.

10. COMPONENT : Select COMPONENT1 / COMPONENT2 input

mode.

11. PC : Select PC input mode.

12. NUMBER : Press the numbers on this board, you can select

channels directly in TV mode.

13. PREV. CH : Previous channel button.

14. PICTURE MODE : Picture modes change as follows : Standard /

Soft / User

15. SOUND MODE : Select Super bass on / off.

16. ASPECT : Select screen aspect ratio : Normal / 16:9(15”,20”) /

4:3(17”) / Zoom

17. CAPTION : Select CC1, CC2, CC3, CC4, T1, T2, T3, T4 and off

the Closed Caption mode.

18. ADD / DEL : Channel ADD or DELETE button.

19. TV / Cable : Select Air / CATV broadcasting mode.

20. SLEEP : Sleep Timer setting. (Sleep 0 ->Sleep 15 ->Sleep 30

->Sleep 45 -> Sleep 60 -> Sleep 90 -> Sleep 120)

+ 21 hidden pages