Dacor RNR30NFS Planning manual

RNR30NS, RNR30NFS, RNR30NIS, RNR30NIFS

1” (2.5 cm)

Front of open door
Front of handle
Front panel
Rear of front panel

Backguard thickness

External handle

shown, some models

have integral handle

(see inside cover)

6” (15.2 cm) backguard*

*

See table for compatibility

Product width:
29 15/16” (76.0 cm)

35”

(88.9 cm)

to

37”

(94.0 cm)

A
B
C
D

RNR30NI[F]S:

3/8” (9.5 mm)

thick top trim

RNR30N[F]S:

full stainless

steel side panels

RNR30NI[F]S:

3” (7.6 cm)

partial stainless

steel side panels

(removable)

Document # PG05-011

Revised 01/28/15 Page 1/5

Renaissance® 30” Wide

Electric Induction Range

Model Versions

Model Configuration Handle Type

RNR30NS[-C]*

RNR30NFS[-C]*

RNR30NIS[-C]*

RNR30NIFS[-C]*

* Order -C option for corded wiring configuration, see page 3/5 for details.

Freestanding,

(full size side panels)

Freestanding,

(full size side panels)

Built-in/Slide-in

(3” removable side panels)

Built-in/Slide-in

(3” removable side panels)

Product Dimensions

All tolerances ±1/16” (±1.6 mm) unless otherwise noted.

Mounted on

outside of door

Flush handle,

integrated in door

Mounted on

outside of door

Mounted on

outside of door

PLANNING

GUIDE

WARNING

• Observe all governing codes and ordinances during planning
and installation. Contact your local building department for
further information.

• This appliance must be installed in accordance with the
accompanying installation instructions.

Available Backguard

Part Number Description Compatibility

ADRB30E06 6 Inch

Models RNR30NIS and RNR30NIFS come equipped from the factory
with flat stainless trim piece in place of a backguard. A backguard may be
purchased as an optional accessory. Add an additional 1/16 inch to depth
dimensions below when installing a backguard on models RNR30NIS and
RNR30NIFS.

Standard on models RNR30NS,
RNR30NFS, Optional on models
RNR30NIS, RNR30NIFS

All specications subject to change without notice.

OVERALL DEPTH DIMENSIONS - SIDE VIEW

Dimension

A 46 1/4” (117.5 cm) 46 1/16” (117.0 cm)

C 25 1/2” (64.8 cm) 25 5/16” (64.3 cm)

D 23 3/8” (59.4 cm) 23 3/16” (58.9 cm)

Dimension RNR30NS RNR30NIS

B 27 7/8” (70.8 cm) 27 11/16” (70.3 cm)

The trim on models RNR30NS and RNR30NFS are not
compatible with a downdraft vent.

Models RNR30NIS and RNR30NIFS are compatible with Dacor
downdraft vent model ERV3015 only.

RNR30NS,

RNR30NFS

Phone: [phone]www.dacor.com

RNR30NIS, RNR30NIFS

RNR30NS, RNR30NFS, RNR30NIS, RNR30NIFS

Cabinet face

Countertop

Range trim resting

on countertop

RNR30NI[F]S range

3/8” min. (1.0 cm)
flat countertop
overhang

28 5/16” (71.9 cm)

ERV3015
downdraft

3/8” min. (1.0 cm) space
required behind ERV3015
chassis to clear stiffener

ATKR30SR
trim kit
installed

Cabinet face

Countertop

Range trim resting

on countertop

Back of
side panel
rests against
cabinet face

RNR30NI[F]S range

3/8” min. (1.0 cm)
flat countertop
overhang

ATKR30SR
trim kit
installed

28 5/16” (71.9 cm)

3 inch
side panel

ERV3015
downdraft

3/8” min. (1.0 cm) space
required behind ERV3015
chassis to clear stiffener

Document # PG05-011

Revised 01/28/15 Page 2/5

Product Dimensions (cont.)

Renaissance 30” Wide

Electric Induction Range

PLANNING

GUIDE

SIDE VIEW - DOWNDRAFT ERV3015 WITH SLIDE-IN, SELF-

RIMMING INSTALLATION WITH 3” SIDE PANELS INSTALLED

AND ATKR30SR TRIM KIT (REQUIRED) INSTALLED

Electrical Specifications

ELECTRICAL REQUIREMENTS

Electrical Circuit

Required

240 Vac 60 Hz, 4 wire*,

50 Amp.

*Two 120 Vac hot (L1 and L2), one neutral (N1) and one ground.

**This information above is for reference only. If the above data
does not agree with the product data label, use the data on the
product data label.

IMPORTANT: Models with -C option suffix are ranges that
come with a factory installed 4-wire appliance cord with NEMA
14-50P plug. For freestanding ranges installed in Canada, a
factory installed 4-wire appliance cord with NEMA 14-50P plug
is required, without modification. For slide-in ranges installed in
Canada and all ranges installed outside of Canada, the 4-wire
appliance cord configuration (-C type) is optional and may be
utilized where local codes permit The plug is designed to plug
directly into a NEMA 14-50R electrical receptacle installed by a
licensed electrician according to the above specifications.

NEMA 14-50P PLUG NEMA 14-50R RECEPTACLE

Total Connected

Load**

11.5 kW (48.0 Amp.)

SIDE VIEW - DOWNDRAFT ERV3015 WITH SLIDE-IN, SELF­RIMMING INSTALLATION WITH 3” SIDE PANELS REMOVED

AND ATKR30SR TRIM KIT (REQUIRED) INSTALLED

Factory Wiring

Model Factory Electrical Connection

RNR30NS,

RNR30NFS

RNR30NS-C,

RNR30NFS-C

RNR30NIS,

RNR30NIFS

RNR30NIS-C,

RNR30NIFS-C

Power cord not installed. Not for installation in Canada.

Cord connected, for installation in Canada (and U.S.A.,

where local codes permit).

No power cord. May be installed in Canada and U.S.A.

Cord connected, may be installed in Canada and U.S.A.,

where local codes permit.

All specications subject to change without notice.

Phone: [phone]www.dacor.com

RNR30NS, RNR30NFS, RNR30NIS, RNR30NIFS

Document # PG05-011

Revised 01/28/15 Page 3/5

Renaissance 30” Wide

Electric Induction Range

All tolerances +1/16” (+1.6 mm), -0 unless otherwise noted.

B

13” (33.0 cm)

4

max.

18” (45.7 cm)

min.

Note 2

4

Non-combustible
surface along
back wall
recommended

Note 1

A

Grate
level

Suggested
location of

3

utilities

Top of
finished
counter

Note 5

PLANNING

GUIDE

■ Failure to meet or exceed the maximum and
minimum dimensions/clearances stated may result
in a fire hazard.

■ The shaded area shown denotes the location of
the electrical junction box/receptacle. This is the
suggested location. For replacement purposes, the
location of the existing electrical supply may be
utilized provided that it does not interfere with the
sides or rear of the range.

■ Access to the remote circuit breaker panel/fuse box,
with the range in place and operating, must also be
allowed for in the installation.

■ The electrical junction box/receptacle must be
located so that it does not interfere with the range
when it is installed and under operation. In addition,
the junction box/receptacle must be located so
the range can be removed for service and remain
connected to power.

■ To eliminate the risk of burns or fire by reaching
over heated surface units, cabinet storage space
located above surface units should be avoided. If
cabinet storage space is to be provided directly
above the range, the risk of personal injury may be
reduced by installing a range hood.

■ In all instances, installation of a range hood is highly
recommended. The hood should project horizontally
a minimum of five (5) inches beyond the face of
the cabinets. See the range hood specifications for
minimum clearances.

■ The range may be installed flush to the rear wall.
See diagram and notes for rear wall surface
requirements. It is not necessary to install non­combustible materials behind the range below the
countertop height.

■ Any openings in the wall behind the appliance or in
the floor underneath it must be sealed.

C

A* B

30 1/16” min.

(76.4 cm)

* See the cutout dimensions on following page for self-rimming installations.

FREESTANDING INSTALLATION CABINET CUTOUT DIMENSIONS - RNR30NS, RNR30NFS, RNR30NIS AND RNR30NIFS

1

30” (76.2 cm) min. vertical clearance from top of range grates to bottom of uncovered wood or metal cabinet. 24” (61 cm) min. clearance if bottom of wood
or metal cabinets are protected by not less than 1/4“ (0.6 cm) flame retardant millboard covered with no less than No. 28 MSG sheet steel 0.015” (0.04
cm) stainless steel, or 0.024” (0.06 cm) aluminum or 0.020” (0.05cm) copper. If installing range hood, check the hood specifications for minimum required
clearances.

2

Cabinet/countertop depth is at discretion of customer but cabinet face SHALL NOT protrude further than rear of front panel. See Product Dimensions.

3

Consult local code and following pages for requirements.

4

This specification not applicable for cabinets more than a horizontal distance of 1” (2.6 cm) min from edge of range.

5

1” (2.6 cm) min. to combustible side walls above range (both sides).

All specications subject to change without notice.

36” (91.4 cm) recommended

30” (76.2 cm) min.

37” (94.0 cm) max.

Phone: [phone]www.dacor.com

C

35” (88.9 cm) min.

RNR30NS, RNR30NFS, RNR30NIS, RNR30NIFS

Rear wall or
countertop edge

countertop opening

29 1/4” (74.3 cm)

30 1/16” (76.2 cm)

cabinet opening

below countertop

below countertop

Cabinet face

Notch countertop

to width of cabinets

3/8” min. (9.5 mm)

countertop overhang

1” min. (2.6 cm)
to any combustibles
above counter both sides

20”

(50.8 cm)

to

23”

(58.4 cm)

20”

(50.8 cm)

Countertop front

Max.

overhang

1 5/8”

(4.1 cm)

Rear wall or
countertop edge

countertop opening

29 1/4” (74.3 cm)

30 1/16” (76.2 cm)

1

cabinet opening

below countertop

below countertop

Cabinet face

Notch countertop

to width of cabinets

3/8” min. (9.5 mm)

countertop overhang

1” min. (2.6 cm)
to any combustibles
above counter both sides

23”

(58.4 cm)

Max.

overhang

1 5/8”

(4.1 cm)

Countertop front

34 3/4”

(88.3 cm)

to

36 7/8”

(93.7 cm)

(see diagrams)

Countertop
1 5/8 (41.1 cm)
max. thickness

Document # PG05-011

Revised 01/28/15 Page 4/5

Renaissance 30” Wide

Electric Induction Range

Cabinet Cutouts for Self-Rimming Installation (Models RNR30NIS and RNR30NIFS Only)

All tolerances +1/16” (+1.6 mm), -0 unless otherwise noted.

Countertop height: 34 3/4” (88.3 cm) min.
36 7/8” (93.7 cm) max.
Countertop thickness: 1 5/8” (4.1 cm) max.

■ The self-rimming installation of the RNR30NI[F]S range creates a
“built-in” look where the range trim overlaps the countertop on both
sides and in back.

■ Observe all vertical cabinet clearances on page 3/5.

■ On self-rimming installations when sliding the range into position, it
will stop when the rear of the control panel or side panels contact the
notches toward the front of the countertop.

PLANNING

GUIDE

All specications subject to change without notice.

TOP VIEW - SLIDE-IN, SELF-RIMMING INSTALLATION,

MINIMUM REQUIRED CABINET DEPTH: 23 3/8”

1

To create a “built-in look” on the front of the cabinet, this
dimension may be changed to 29 1/4” (74.3 cm), with the
width at the notches remaining 30 1/16”. This configuration is
only for models RNR30NIS and RNR30NIFS with side panels
behind door removed.

TOP VIEW - SLIDE-IN, SELF-RIMMING INSTALLATION,

3” SIDE PANELS REMOVED

3” SIDE PANELS INSTALLED

CABINET DEPTHS 20 3/8” TO 23 3/8”

Phone: [phone]www.dacor.com

RNR30NS, RNR30NFS, RNR30NIS, RNR30NIFS

Rear wall or
countertop edge

countertop opening

29 1/4” (74.3 cm)

downdraft vent opening

27 1/2” (69.9 cm)

30 1/16” (76.2 cm)

2

cabinet opening

below countertop

below countertop

Cabinet face

Notch countertop

to width of cabinets

3/8” min. (1.0 cm)

countertop overhang

1” min. (2.6 cm)
to any combustibles
above counter both sides

23 3/8”

(59.4 cm)

2 5/8” (6.7 cm)

Countertop front

Max.

overhang

1 5/8”

(4.1 cm)

Document # PG05-011

Revised 01/28/15 Page 5/5

Renaissance 30” Wide

Electric Induction Range

Cabinet Cutouts for Self-Rimming Installation (Models RNR30NIS and RNR30NIFS Only)

All tolerances +1/16” (+1.6 mm), -0 unless otherwise noted.

Countertop height: 34 3/4” (88.3 cm) min.
36 7/8” (93.7 cm) max.

Countertop
1 5/8 (41.1 cm)
max. thickness

(see diagrams)

34 3/4”

(88.3 cm)

to

36 7/8”

(93.7 cm)

Countertop thickness: 1 5/8” (4.1 cm) max.

■ Trim kit PN ATKR30SR is required for proper installation of a
downdraft vent with this range.

■ The self-rimming installation of the RNR30NI[F]S range and ERV3015
downdraft vent create a “built-in” look where the range trim overlaps
the countertop on both sides and the downdraft vent trim overlaps the
countertop in back. The ATKR30SR trim kit, installed on the back of
the range, will cover the front of the downdraft vent chassis.

■ Observe all vertical cabinet clearances on page 3/5.

■ A self-rimming countertop configuration is required for downdraft vent
installation. On installations with a downdraft vent, when sliding the
range into position, it will stop when the rear of the control panel or
side panels contact the notches toward the front of the countertop.

PLANNING

GUIDE

1” min. (2.6 cm)
to any combustibles
above counter both sides

Max.

overhang

1 5/8”

(4.1 cm)

Countertop front

countertop overhang

27 1/2” (69.9 cm)

downdraft vent opening

29 1/4” (74.3 cm)

countertop opening

30 1/16” (76.2 cm)

cabinet opening

below countertop

Notch countertop

to width of cabinets

Cabinet face

below countertop

3/8” min. (1.0 cm)

(51.8 cm)

Rear wall or
countertop edge

20 3/8”

(51.8 cm)

(59.4 cm)

2 5/8” (6.7 cm)

20 3/8”

to

23 3/8”

TOP VIEW - DOWNDRAFT ERV3015 WITH

SLIDE-IN, SELF-RIMMING INSTALLATION,

3” SIDE PANELS INSTALLED

CABINET DEPTHS 23 3/8” TO 26 3/8”

TOP VIEW - DOWNDRAFT ERV3015 WITH

SLIDE-IN, SELF-RIMMING INSTALLATION,

3” SIDE PANELS REMOVED

MIN. REQUIRED CABINET DEPTH: 26 3/8”

All specications subject to change without notice.

2

To create a “built-in look” on the front of the cabinet, this
dimension may be changed to 29 1/4” (74.3 cm), with the
width at the notches remaining 30 1/16”. This configuration
is only for models RNR30NIS and RNR30NIFS with side
panels behind door removed.

Phone: [phone]www.dacor.com