Dacor RNO127S208V Planning manual
Document # PG01-015
J
RNO, RNOV
Revised 05/22/14 Page 1/2
Renaissance® 27” and 30” Wide
Single Wall Ovens
Product tolerances: ±1/16” (±1.6 mm) unless otherwise stated
Top of
K
Utility
cutout
C
A
chassis
B
PLANNING
GUIDE
WARNING
• Observe all governing codes and ordinances during planning
and installation. Contact your local building department for
further information.
• This appliance must be installed in accordance with the
F
G
H
D
accompanying installation instructions.
2 3/8”
(6.0 cm)
1 7/8”
(4.8 cm)
Conduit:
60” (152 cm)
Control panel
front
Control panel
L
E
M
Top of
chassis
long
Epicure
(Order kit #AROVH30S)
Handle Dimensions
Millennia
Flush
side view
ELECTRICAL SPECIFICATIONS
Model
RNO[V]127
RNO[V]127
21 1/2”
(54.6) cm
RNO[V]130
* To top of chassis notch behind control panel
RNO[V]130
*** Two 120 Vac hot (L1 and L2), one neutral, one ground
The above specifications are for reference only. See the appliance data
plate for exact specifications.
Model
(A) Overall
Width
26 7/8”
(68.3 cm)
29 7/8”
(75.9 cm)
Dedicated Circuit
Requirements
240 Vac 60 Hz., 4-wire,***
240 Vac 60 Hz., 4-wire,***
30 Amp.
30 Amp.
(B) Chassis
Width
25 3/8”
(64.5 cm)
28 3/8”
(72.1 cm)
(C) Overall
Height
27 3/4”
(70.5 cm)
27 3/4”
(70.5 cm)
Total Connected Load
240 Vac 60 Hz,
19.0 Amp., 4.7 kW
240 Vac 60 Hz,
24.5 Amp., 6.0 kW
(D)* Chassis
Height
27 3/8”
(69.5 cm)
27 3/8”
(69.5 cm)
(E) Control
Panel
Overlay
3/8”
(1.0 cm)
3/8”
(1.0 cm)
(F) Utility
Cutout Width
6 1/2”
(16.5 cm)
All specications subject to change without notice.
(G) Utility
Cutout Height
5”
(12.7 cm)
(H) Utility
Cutout Depth
7 7/8”
(20.0 cm)
(J) Control
Panel Depth
3/4”
(1.9 cm)
(K) Chassis
Depth
24”
(61.0 cm)
(L) Control
Panel Notch
Depth
1/2”
(1.3 cm)
(M) Notch
Height
3/4”
(1.9 cm)
Phone: (800) 793-0093www.dacor.com
Document # PG01-015
RNO, RNOV
Revised 05/22/14 Page 2/2
Renaissance 27” and 30” Wide,
Single Wall Oven
Cabinet tolerances: +1/16” (+1.6 mm) -0, unless otherwise stated
36” typ.
(91.4 cm)
N
Recommended
electrical
location
1” (2.5 cm) min.
to bottom of
cabinet door
PLANNING
1“ (2.5 cm) min. to combustibles
1 1/2”
(3.8 cm)
typical counter
R
P
3/4” (1.9 cm)
support platform
SINGLE WALL OVEN - INSTALLED UNDER COUNTER
Minimum interior cabinet depth: 24” (61.0 cm)
1“ (2.5 cm) min.
to combustible floor
GUIDE
Recommended
electrical
location
4” typical toe kick
R
P
1” (2.5 cm) min.
to top of
cabinet door
4” typical toe kick
SINGLE WALL OVEN - CUTOUT DIMENSIONS
Alternate
electrical
support platform
location
3/4” (1.9 cm)
31 1/4” (79.4 cm)
recommended
Model
RNO[V]127
RNO[V]130
(N) Minimum
Cabinet
Width
27”
(68.6 cm)
30”
(76.2 cm)
(P) Cut Out Width
25 1/2” (64.8 cm)
minimum (recommanded)
26 1/8” (66.4 cm)
maximum
28 1/2” (72.4 cm)
minimum (recommended)
29 1/8” (74.0 cm)
maximum
(R) Minimum Cutout
Height
27 1/2”
(69.9 cm)
27 1/2”
(69.9 cm)
All specications subject to change without notice.
Phone: (800) 793-0093www.dacor.com
Loading...