CyClone HD4836 Operation Manual
'
Operation Manual &
Part List
WARNING!!
Clclone abrasive
garnet,
walnut shells,
depending
on the type
*
Always
HD4836
Side 0pen
w/Dc4000
Abrasive blast
injury andlor
It is suggested
This blast
DO NOT MIX FLUIDS WITH BLAST MATERIAL!
blast cabinets
silicon carbide
of
close cabinet doors before
cabinets
property
this manual is kept for reference of
cabinet is set up for use with DRYAbrasive
are designed for cleaning and
blasting
material
produce a powerfulflow
damage, read this manual thoroughly before
lntroduction
and sands. The system
the air
pressure
and
Precautionary
blasting.
Blast
Ms1500
&
abrasive
of
blaster model number and replacement
finishing with dry blast materials
is
at all openings. The blast system
sealed
used.
Gabinet
particles.
Materials ONLY!
To
operating the
Check List
avoid
such as
perconal
blast cabinet.
glass
will
pafts
beads,
produce
listing.
aluminum
several
oxide,
different
blasting
finishes,
*
Make sure all air connections
*
Do Not0perate0ver
*
Always clean any
*
Use lower air
*
*
*
keep
Always
area
DONOTUSESTEELSHoTINTHISBLASTCABINffI
blast
NoT USE LIQUID OF
D0
the hoses
the
will result in
unit will void the wananty
properly.
120
spilt blasting material from
pressure
blast stream
pitting
Use
are secure.
PSl.
moving
uneven
and
metals
in a circular or
blast surfaces.
possibly
THIS
to clean soft
and
ANY KIND lN
of any liquids will void the wananty and
work
and
delicate
lt can cause floors to become
area.
parts.
horizontal
motion.
Any blast concentrated
Thiscabinetisnotdesignedfororsetupforsteelshot.
injury
BLAST CABlNEliquids will cause the
operator! This includes black
the
could
cause
damage to the
slippery.
beauty.
blast media to
cabinet!
in one
clump
Useofsteelshotinthis
not flow through
up and
How To
r1
Assemble
and Install
Blast
Cabinet
l) Attach system to electricity.
2)
Attach air to the foot valve
hand side). Slide
3)
Open
4) Place
cabinet and
part
on
5) Turn light and
6) Depress foot
circular
window. This will cause
Also, be careful not to hit
the window to
Abrasive feed from separator:
motions.
hose
metal
dust collection
pedal
from foot
pour
15-25lbs.
grate
and begin
to be blasted.
This will
frosting
the
break and
possibly
Bulbs are
assembly.
pedal
system
to blast. Make
help ensure
abeady
lt is Y+" npt.
over this
of
blast
Close door.
on.
a more
of the window (which
window with the
injure
the operator.
in lamp.
Screw
barb
material
into cabinet
sure
to
even result. Do
gun
hose barb
and
tighten
hopper.
keep the spray
not blast directly
means
or with
you
your parts.
into the cabinet
clamp
provided.
pattern
will
have
moving
This could cause
(left
in
at the
to replace
it).
1) The
To operate the air
pick
up hose assembly
in operation, the
to draw from.
a braided hose sleeve
hoses and
partially
out the
or completely
separator
There is
gun
purge
should not operate non
minutes
1) Attach air
2)
With the dust collector
send air thru the filter,
to be discarded.
the air when
per
cieaning.
to the Yz" npt ball
Generally,
purging
feeds
will continuously
a hole located
near it.
on
for
in
stop.
housing
thus
is
complete.
This is to smooth
the media
a smooth
the
dust collection
This is
valve
closed,
knocking
5 -10
directly
from the
in the
feed from
flow of media
for occasional
located on
turn valve
from
dust
minutes are
separator. With
have clean blast abrasive
pick
up hose on the exterior of
out the flow
the separator to the cabinet. Cover
gun.
the
to
system: Please note this
cleaning and for use
the
the cartridge filter
of
side
on, allowing interior air
the dust collector
sufficient. Turn air valve
the dust collection
for the
blast material
of
purge
no more than
housing.
waves to
to the bottom hopper
off and disconnect
the cabinet
pick
up
through
the
system
hose
with
the
hole
5
Loading...