CyClone NA-930, CY-1000, CY-1000R, CY-3000R Installation And Operating Instructions Manual

Self-Cleaning Range Hoods

Hottes Autonettoyantes

(Model/Modèle NA-930/R)

(Model/Modèle CY-1000/R)

(Model/Modèle CY-3000R)

Installation and Operating Instructions

Installation and Operating InstructionsInstallation and Operating Instructions

Installation and Operating Instructions

Instructions d’installation et d’opération

Instructions d’installation et d’opération Instructions d’installation et d’opération

Instructions d’installation et d’opération

Please read all instructions before installing and operating.

All wiring must be in accordance with national and local electrical codes.

TP

2

TABLE OF CONTENTS

TABLE OF CONTENTSTABLE OF CONTENTS

TABLE OF CONTENTS

Titles/ titres Page(s)

Safety Instructions 3

Tools and Materials 3

Preparation for installation 4

Installation Procedures 4

Providing Electrical 5

Making the Electrical Connection 5

Use and Care 5

Operating Instructions 6

Specifications 6

Circuit Assembly Drawing for Twin Motor Range Hood 7

Service Parts 8

Cyclone Range Hood Limited Warranty 9

3

IMPORTANT SAFETY INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONSIMPORTANT SAFETY INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE ALL INSTRUCTI

READ AND SAVE ALL INSTRUCTIREAD AND SAVE ALL INSTRUCTI

READ AND SAVE ALL INSTRUCTIONS BEFORE INSTALLING OR OPERATING YOUR

ONS BEFORE INSTALLING OR OPERATING YOUR ONS BEFORE INSTALLING OR OPERATING YOUR

ONS BEFORE INSTALLING OR OPERATING YOUR

CYCLONE RANGE HOOD

CYCLONE RANGE HOODCYCLONE RANGE HOOD

CYCLONE RANGE HOOD

1. Cyclone range hood is for general purpose ventilating use only. Do not use it to exhaust hazardous,

explosive materials or vapors.

2. The safety mesh that covers the inlets to the fan must be cleaned periodically to prevent excess

grease buildup. Make sure the mesh is installed before operating the fan.

3. Do not use more than 50W incandescent light bulbs for any model. Do not use round shaped light

bulb for models CY1000 or CY1000R. Recommended use of tubular light bulb (T10) or 23W
florescent tube (equivalent to a 90W incandescent light bulb).

4. Ensure the power is turned off before installation or maintenance. If you move the range hood to

make room for working on the cabinet, turn off the 220V power for an electric range at the service
entrance. Before moving a gas range, shut off the gas.

5. When cutting or drilling into walls or ceilings, be careful not to damage existing electrical wiring and

other hidden utilities. Use only metal ductwork.

6. All electrical connections must be in accordance with local codes, ordinances, or National Electrical

Code. If you are unfamiliar with methods of installing electrical wiring, secure the services of a
qualified electrician.

7. When installed, the bottom edge of your Range Hood should be 24” – 32” above the top of cooking

surface.

8. Always keep the duct clear to maintain proper airflow for venting.

9. To reduce the risk of fire, electric shock and to properly exhaust air, ducted fans must always be

vented outside. Do not vent exhaust air into spaces within walls, ceilings, attics, crawl spaces or
garages. Do not connect this fan with any solid-state speed control device.

10. To reduce the risk of a range top grease fire, always have the fans turned on when cooking at high

heat or when cooking flaming foods. Do not leave your range unattended when cooking at high
setting. Always keep the range hood clean. Grease should not be allowed to accumulate on fans or
hood.

TOOLS AND MATERIALS REQUIRED

TOOLS AND MATERIALS REQUIREDTOOLS AND MATERIALS REQUIRED

TOOLS AND MATERIALS REQUIRED

• Electrical drill or Ratchet Driver

• ½” drill bit for drilling pilot holes

• 1 ¼” drill bit for drilling electrical wiring access

hole

• Screwdrivers: philips & straight blade

• Pliers

• Tape measure or ruler and pencil

• Electrical supplies for wiring

• Aluminum foil tape and/or duct tape

• Hammer

• Jigsaw or saber saw

• 6 tapping screws (supplied)

• 4 hood mount screws (supplied)

• 2 rectangular oil collectors (supplied)

• 2 round shape oil collectors (supplied)

• 1 rectangular damper (supplied only with

rectangular venting models)