Cuisinart DGB-850 User Manual
Troubleshooting
PROBLEM CAUSE SOLUTION
The coffeemaker
is beeping
The brew cycle
will not start
Coffee is weaker
than usual
The coffeemaker
is not grinding
beans
EMPTY
appears in LCD
display
Filter door is not closed • Check to be sure that all components of the filter compartment
Filter basket is not in
place
Coffee grounds and filter
from previous use are
still in filter basket
There is no water in the
water reservoir
There are not enough
beans in the hopper
Strength setting
is incorrect
The hopper may be
too full
Coffee grounds and filter
from previous use are
still in filter basket
are in place
• Close filter door (you will hear a click if the door is properly shut)
• Open filter door by pressing the filter door Release button
• Hook filter basket with cover onto door
• Close filter door (you will hear a click if the door is properly shut)
• Remove filter and used coffee grounds
• Add new filter
• Fill the water reservoir using the water level markings
• Be sure there are enough beans in your hopper for the amount of
coffee you intend to brew
• Check your strength setting — displayed on the LCD screen
• To change your strength setting, press the Strength Control button
• Turn the coffeemaker off and unplug
• Remove some of the beans from the hopper
• Remove filter and used coffee grounds
• Add new filter
Fully Automatic Burr Grind & Brew™ Thermal Coffeemaker
BEFORE FIRST USE
Before using your Cuisinart® Fully Automatic Burr Grind & Brew™ Thermal Coffeemaker for the
first time:
ONTO BASE. During the manufacturing process, dust can get trapped in your coffeemaker. We recommend
flushing out the system before brewing your first pot of coffee. Simply follow “Making Coffee with PreGround Beans,” page 10 in the Instruction Booklet. Skip step #1 and be sure to use only water and a paper
filter…no coffee! Once you’ve done that, brew a pot of real coffee and get ready to enjoy Cuisinart at its best!
BE SURE TO REMOVE POLYBAGS FROM CARAFE AND COFFEEMAKER. PLACE CARAFE BACK
Quick Reference SETUP Guide
Fully immerse the charcoal water filter in cold tap
water and soak for 15 minutes. Flush filter by running
cold tap water through holes in bottom of compartment
for 10 seconds (see complete instructions on page 8 of
your instruction booklet). Insert the filter into the water
filter holder. Open the water reservoir and place filter
holder into the unit.
Open the filter basket door by pressing the
Release button, and insert a paper filter or
3.
permanent filter into the filter basket holder.
Replace the cover, and close door.
Pour your desired amount of water into the
water reservoir. A water level indicator is
2.1.
located on the side of the unit.
Helpful Hint: “Pre-heat” your carafe by
rinsing it out with hot water before brewing.
Remove hopper lid, fill with beans,
and replace the lid.
4.
PG-36702
CLEAN is flashing
on the LCD
when the unit
is turned on
The coffeemaker
will not enter
CLEAN mode
Coffeemaker needs
to be decalcified
The water reservoir
is empty
• Run a clean cycle – follow the decalcification directions on
page 11 of Instruction Booklet
• Fill the water reservoir with decalcification mixture before turning
the coffeemaker on - Follow the decalcification directions on
page 11 of Instruction Booklet
IMPORTANT
Do not throw away. Read before operating your new
Brewing System. Keep for future reference.
These helpful hints are intended to be a supplement to the Instruction Booklet. In order to ensure
safe operation and optimum performance, please read the entire Instruction Booklet.
© 2017 Cuisinart
Press the ON/OFF button to turn on the coffeemaker.
Select the amount of cups you wish to brew by turning
5.
the Grind Control knob. Select your desired coffee
strength by pressing the Strength button. Your selected
coffee strength will be indicated in the bar on the LCD
display.
6.
To start grinding & brewing, press the BREW
button. Once the coffee has finished brewing,
five beeps will sound. The unit will
immediately shut off. The thermal carafe will
keep coffee hot for hours.
1.
2.
Quick Reference PROGRAMMING Guide
To Set the Time: Press and hold the Hour or Minute button until the clock begins flashing. Hold down
the Hour or Minute button to quickly scroll through the numbers. When desired time approaches,
release the button and press repeatedly to advance one digit at a time. To finish, wait for the numbers
to stop flashing.
To Program Auto ON: Press the ON/OFF button, then press the Program button once until Auto ON is
displayed on LCD. Hold the Program button until the clock begins flashing. Set the time you want
coffee to begin brewing (follow “Set the Time” instructions). Once you are done setting the time, leave
untouched. The clock will display the time of day and the Auto ON indicator, to remind you that the
programming function is in use.
3.
4.
At the programmed time, the white ON/OFF indicator light will come on, as well as BREW button light,
indicating that the brew cycle is starting.
To start the brew cycle at the same time on another day, simply press the ON/OFF button and then
press the Program button once. The Auto ON icon will be displayed on the LCD display.
Keeping It CLEAN
PERMANENT FILTER, FILTER BASKET, FILTER BASKET COVER,
CARAFE AND LID.
Wash in warm, soapy water and rinse thoroughly or clean in the upper rack of the dishwasher.
Dry all parts after every use.
TO CLEAN GRINDER OF COFFEE BEANS
1. Remove hopper cover.
2. Scoop out remaining beans from the hopper.
3. Place the clean, dry filter basket assembly in place (a paper filter can be used if desired).
4. Press the ON/OFF button to turn the coffeemaker on.
5. Press and hold down the Brew button until the coffeemaker begins to grind the beans.
6. After grinding stops, be sure to turn coffeemaker off.
7. Dispose of or re-purpose coffee grinds in filter basket.
8. Use a damp cloth to clean the hopper.
9. Leave the cover off to let the hopper dry completely before adding coffee beans.
Loading...