CTEK XC 800 User Manual
CTEK XC 800
Battery charger
For lead-acid batteries 1.2–100Ah
User Manual and guide to
professional battery charging for
Starter and Deep Cycle batteries.
GB
INTRODUCTION
Congratulations on your purchase of your new professional CTEK XC 800 Switch Mode
Charger with Pulse Maintenance. CTEK XC 800 is a member of a family of professional chargers from CTEK Sweden AB. It represents the state-of-the-art technology for battery charging.
A CTEK XC 800 will prolong the lifetime of your battery. Read this user manual and follow the
instructions carefully before using the charger.
SAFETY
The charger is designed to charge 6V lead-acid batteries from 1.2 to 32Ah. However, the
•
charger can maintain batteries up to 100Ah. Do not use the charger for any other purpose.
Use safety glasses and turn your head away when connecting or disconnecting a battery.
•
Battery acid is corosive. Rinse immediately with water if acid comes into contact with skin or
•
eyes. Seek medical advice.
Make sure that the cable is not being pinched or in contact with warm surfaces or sharp
•
edges.
While charging, a battery can emit explosive gases, so it is important to avoid sparks in the
•
immediate area.
Always provide for proper ventilation during charging.
•
Avoid covering the charger.
•
Make sure that the electrical cable does not come into contact with water.
•
Never charge a frozen battery.
•
Never charge a damaged battery.
•
Do not place the charger on the battery while charging.
•
The electrical connection must fulfil the national heavy current requirements.
•
Check the cabling in the charger before use. Make sure there are no cracks in the cabling or
•
in the protective covering. A charger with damaged cables may not be used.
Always check that the charger has gone over to maintenance charging mode before leaving
•
the charger unattended and connected for long periods. If the charger had not gone over
to maintenance charging within 3 days, this is an indication of a problem. In this case the
charger must be disconnected manually.
All batteries fail sooner or later. A battery that fails during charging is normally taken care of
•
by the chargers advanced control, but certain uncommon errors in the battery can still arise.
Don’t leave the battery charger unattended for a longer period of time.
Only mount the charger on a flat surface.
•
This equipment may not be used by children or by those who can not read and understand
•
the manual if they are not supervised by a responsible person who can guarantee that the
battery charger is being used in a safe manner. Store and use the battery charger out of the
reach of children. Make sure that children do not play with the battery charger.
BATTERY TYPES
The following recommendations should only be considered as guidelines. In the event of
uncertainty always refer to the battery manufacturer’s recommendations.
CTEK XC 800 is suitable for charging all types of 6V lead-acid batteries: open batteries, MF,
AGM and most GEL-batteries. Battery sizes from 1.2 to 32Ah. The charger can maintain
batteries up to 100Ah.
CHARGING
Charging batteries mounted in a vehicle:
1. The power cord should be disconnected before connecting or disconnecting the battery
leads.
2. Identify the pole that is grounded (attached to the chassis). Ground is normally connected to
the negative terminal.
3. Charging a negatively grounded battery. Connect the red wire to the positive pole of the
battery and the black cable to the vehicle’s chassis. Be careful not to connect the black cable in
the vicinity of a fuel pipe or the battery.
4. Charging a positively grounded battery. Connect the black wire to the negative pole of the
battery and the red cable to the vehicle's chassis. Be careful not to connect the red cable in the
vicinity of a fuel pipe or the battery.
Charging of a battery not connected to a vehicle:
1. The power cord should be disconnected before connecting or disconnecting the battery
leads.
2. Connect the red wire to the positive pole of the battery and the black cable to the negative
pole.
Connecting the provided cables with eyelet terminals:
Make sure that the cable is not being pinched or in contact with warm surfaces or sharp edges.
When the cable is mounted on the battery, it should not be connected to the charger. Connect
the eyelet terminals to the battery's poles – the red cable to the positive pole and the black
cable to the negative pole. After this, the quick contact can be connected.
Reverse Polarity Protection
If the battery cables are connected incorrectly, the reverse polarity protection will make sure that
the charger and the battery are not damaged. In this case, the red warning lamp
will be lit.
Loading...