Page 1
Crestron MP-FS-RX1/RX2
FreeSpeech® Single/Dual-Channel
Wireless Mic Receiver
Operations & Installation Guide
Page 2
Regulatory Compliance
This product is Listed to applicable UL Standards and requirements by Underwriters Laboratories Inc.
As of the date of manufacture, the MP-FS-RX1 and MP-FS-RX2 have been tested and found to comply with
specifications for CE marking and standards per EMC and Radiocommunications Compliance Labelling.
Federal Communications Commission (FCC) Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following conditions:
(1) This device may not cause harmful interference and (2) this device must accept any interference received,
including interference that may cause undesired operation.
CAUTION: Changes or modifications not expressly approved by the manufacturer responsible for
compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
This document was prepared and written by the Technical Documentation department at:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help
Industry Canada (IC) Compliance Statement
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
The specific patents that cover Crestron products are listed at patents.crestron.com.
Crestron, the Crestron logo, Crestron Toolbox, and FreeSpeech are either trademarks or registered trademarks of
Crestron Electronics, Inc. in the United States and/or other countries. UL and the UL logo are either trademarks or
registered trademarks of Underwriters Laboratories, Inc. in the United States and/or other countries. Other trademarks,
registered trademarks, and trade names may be used in this document to refer to either the entities claiming the
marks and names or their products. Crestron disclaims any proprietary interest in the marks and names of others.
©2012 Crestron Electronics, Inc.
Page 3
Crestron MP-FS-RX1/RX2 Single/Dual-Channel Wireless Mic Receiver
Contents
Single/Dual-Channel Wireless Mic Receiver: MP-FS-RX1/RX2 1
Introduction ............................................................................................................................... 1
Features and Functions ................................................................................................ 1
Specifications .............................................................................................................. 2
Physical Description .................................................................................................... 4
Setup .......................................................................................................................................... 8
Installation ................................................................................................................... 8
Hardware Hookup ....................................................................................................... 8
Uploading and Upgrading .......................................................................................................... 9
Establishing Communication ....................................................................................... 9
Firmware ..................................................................................................................... 9
Operation ................................................................................................................................. 10
Basic Procedures ....................................................................................................... 10
Receiver Controls - Default Settings ......................................................................... 11
Problem Solving ...................................................................................................................... 12
Troubleshooting ......................................................................................................... 12
Further Inquiries ........................................................................................................ 12
Future Updates .......................................................................................................... 12
Return and Warranty Policies .................................................................................................. 13
Merchandise Returns / Repair Service ...................................................................... 13
Crestron Limited Warranty ........................................................................................ 13
Operations & Installation Guide – DOC. 7164B Contents • i
Page 4
Page 5
Crestron MP-FS-RX1/RX2 Single/Dual-Channel Wireless Mic Receiver
Single/Dual-Channel Wireless Mic
Receiver: MP-FS-RX1/RX2
Introduction
Crestron® FreeSpeech® systems provide a very simple and affordable solution for
adding speech reinforcement as part of a complete classroom media presentation
system. The MP-FS-RX1 is a single-channel receiver, capable of supporting one
wireless microphone (MP-FSMIC*). The MP-FS-RX2 is a dual-channel receiver
capable of supporting two wireless microphones. Built-in amplification provides
everything needed to drive a set of speakers (sold separately), and even allows for
the connection of a DVD player, computer, or other program audio sources.
Features and Functions
• Single- or dual-channel receiver for one or two FreeSpeech® wireless
microphones
• Advanced combined RF/IR wireless operation ensures trouble-free
performance
• 2.4 GHz RF technology with “error recovery” minimizes noise and
feedback
• “Automatic Gain Control” maintains consistent speech levels
• Built-in 30 Watt stereo amplifier drives one or two pairs of speakers
• Line output enables connection to an external amplifier or video projector
• Two stereo line inputs provide amplification for a DVD player, laptop
computer, or other program sources
• Speech and program audio signals are independently adjustable via a
control on the wireless mic*
• “Ducking” feature automatically turns down the program source
whenever the instructor speaks
• Built-in master volume, bass, and treble adjustment helps optimize the
overall sound quality
• High-efficiency, energy-saving design minimizes power consumption
during operation and while idle
• Includes external power pack and external antenna(s)
*Item sold separately or as part of a MP-FS100_PAK or MP-FS200_PAK system package.
Operations & Installation Guide – DOC. 7164B Single/Dual-Channel Wireless Mic Receiver: MP-FS-RX1/RX2 • 1
Page 6
Single/Dual-Channel Wireless Mic Receiver Crestron MP-FS-RX1/RX2
and Release
Specifications
Specifications for the MP-FS-RX1/RX2 are listed in the following table.
MP-FS-RX1/RX2 Specifications
SPECIFICATION DETAILS
Communications
Wireless
RF
IR 38 kHz (requires MP-FSIR IR Beacon Sensor*)
Range (typical) 50 ft (~15 m) indoor, subject to site-specific
Wired
USB USB host port for firmware update and
Audio
A-D/D-A Conversion 16-bit, 44.1 kHz
Master Volume Range -55 dB to +20 dB
Bass Gain Range
Treble Gain Range ±15 dB @ 10k Hz
Ducking Adjustment Software adjustable Threshold, Depth, Attack,
2.4 GHz ISM Device; 79 channels, FHSS
(2402 to 2480 MHz)
conditions
configuration
±15 dB @ 100 Hz
Alert Tone Software configurable functionality
Frequency Response 20 Hz to 20 kHz ±0.5 dB
S/N Ratio 75 dB 20 Hz to 20 kHz A-weighted
THD+N 0.7% 20 Hz to 20 kHz
Output Power 15 Watts per channel at 8 or 4 Ohms
Amplifier Protection Electronic short-circuit and overload protection
Power Requirements
Power Pack 2.0 Amps @ 24 Volts DC, 100-240 Volts AC,
50/60 Hz power pack, included
Environmental
Temperature 41° to 104° F (5° to 40° C)
Humidity 10% to 90% RH (non-condensing)
Heat Dissipation 35 BTU/Hr
Enclosure
Chassis Metal with polycarbonate label overlay
Faceplate Plastic with polycarbonate label overlay
Mounting Freestanding
Dimensions
Height 2.36 in (60 mm)
Width 8.12 in (207 mm)
Depth 5.95 in (152 mm)
(Continued on following page)
2 • Single/Dual-Channel Wireless Mic Receiver: MP-FS-RX1/RX2 Operations & Installation Guide – DOC. 7164B
Page 7
Crestron MP-FS-RX1/RX2 Single/Dual-Channel Wireless Mic Receiver
US/International
MP-FS-RX1/RX2 Specifications (Continued)
SPECIFICATION DETAILS
Weight
MP-FS-RX1 2.3 lbs (1.1 kg)
MP-FS-RX2 2.4 lbs (1.1 kg)
Included Accessory
Power Pack Desktop, 24 VDC, 2 A (50 Watts), Regulated,
Available Accessories
CBL-KAUDIO-RCAM2-L-P-50 RCA Stereo Audio Cable Kit, Plenum, 50 ft
CBL-RCA2-1.5 Crestron Certified RCA Stereo Audio Interface
Cable, 1.5 ft
CBL-RCA2-3 Crestron Certified RCA Stereo Audio Interface
Cable, 3 ft
CBL-RCA2-6 Crestron Certified RCA Stereo Audio Interface
Cable, 6 ft
CBL-RCA2-12 Crestron Certified RCA Stereo Audio Interface
Cable, 12 ft
CBL-SPK-P-35 Speaker Cable, 16 AWG, Plenum, 35 ft
FS6 6.5” 2-Way Surface Mount Speakers, Pair
FSDI8 8” Drop-in Ceiling Speakers, Pair
MP-FSIR FreeSpeech IR Beacon
MP-FSMIC FreeSpeech Wireless Microphone
MP-FS-PAS FreeSpeech PA Audio Sensor
*Item sold separately or as part of a MP-FS100_PAK or MP-FS200_PAK system package.
Operations & Installation Guide – DOC. 7164B Single/Dual-Channel Wireless Mic Receiver: MP-FS-RX1/RX2 • 3
Page 8
Single/Dual-Channel Wireless Mic Receiver Crestron MP-FS-RX1/RX2
Physical Description
This section provides information on the connections, controls and indicators
available on the MP-FS-RX1/RX2.
MP-FS-RX1 Front View
MP-FS-RX2 Front View
MP-FS-RX1/RX2 Rear View
4 • Single/Dual-Channel Wireless Mic Receiver: MP-FS-RX1/RX2 Operations & Installation Guide – DOC. 7164B
Page 9
Crestron MP-FS-RX1/RX2 Single/Dual-Channel Wireless Mic Receiver
8.12 in
(207 mm)
2.25 in
(58 mm)
2.36 in
(60 mm)
0.38 in
(10 mm)
5.10 in
(130 mm)
0.62 in
(16 mm)
5.33 in
(136 mm)
8.00 in
(203 mm)
1 2 3 4 5
6 7 8 9
10 11 12 13 14 10
MP-FS-RX1/RX2 Overall Dimensions (MP-FS-RX2 Shown)
Operations & Installation Guide – DOC. 7164B Single/Dual-Channel Wireless Mic Receiver: MP-FS-RX1/RX2 • 5
Page 10
Single/Dual-Channel Wireless Mic Receiver Crestron MP-FS-RX1/RX2
USB
Pin 2 Pin 1
Pin 3 Pin 4
Connectors, Controls & Indicators
# CONNECTORS1,
CONTROLS &
INDICATORS
1 COMPUTER
2 Beacon Sensor 1 – 2
1 2
T R S T R S
3 MUTE SENSOR
S G
4 ALERT OUT
N.O.
2A 50V
MAX.
5 LINE IN 1 – 2
DESCRIPTION
(1) USB Type B female; USB computer
console port for firmware update and
configuration only
PIN DESCRIPTION
1 +5 VDC
2 Data -
3 Data +
4 Ground
(2) 3-pin 3.5 mm detachable terminal blocks;
Interface for up to (2) MP-FSIR IR Beacon
Sensors2 per terminal block; (4) beacon
sensors, total
(1) 2-pin 3.5 mm detachable terminal block;
Contact closure sensing input, or interface for
MP-FS-PAS PA Audio Sensor
NOTE: Sensor black wire connects to terminal
G; red wire connects to terminal S.
Mutes all audio outputs when a contact closure
or PA audio signal is sensed
(1) 2-pin 3.5 mm detachable terminal block;
Normally open isolated relay, software
configurable functionality;
Rated 2 Amp, 50 Volts maximum;
Controlled by mic ALERT button. (Hold button
for 8 seconds, alert relay closes, speakers emit
two beeps)
(4) RCA female comprising (2) unbalanced
stereo line-level audio inputs;
Maximum Input Level: 2 V
Input Impedance: 18k Ohms nominal
rms
2
;
6 • Single/Dual-Channel Wireless Mic Receiver: MP-FS-RX1/RX2 Operations & Installation Guide – DOC. 7164B
6 LINE OUT
(2) RCA female;
Unbalanced stereo line-level audio output;
Maximum Output Level: 2 V
rms
Output Impedance: 100 Ohms nominal
(Continued on following page)
Page 11
Crestron MP-FS-RX1/RX2 Single/Dual-Channel Wireless Mic Receiver
Connectors, Controls & Indicators (Continued)
# CONNECTORS1,
CONTROLS &
INDICATORS
7
SPEAKER OUT 4/8Ω:
8 G
9 24 VDC 2.0A
10 Antenna
11 PWR
12 BASS
DESCRIPTION
(2) 2-pin 5 mm detachable terminal blocks
Left & right channel speaker-level audio
outputs;
Wire Size: Connector accepts 14 AWG
maximum;
Output Power: 15 Watts per channel at 8 or 4
Ohms
(1) 6-32 screw, chassis ground lug
(1) 2.0 mm DC power;
24 Volt DC power input (power pack included)
(1) Connection for supplied antenna
(MP-FS-RX1)
(2) Connection for supplied antennas
(MP-FS-RX2)
Green LED, indicates operating power supplied
from external power pack
Rotary low frequency boost/cut adjustment
13 TREBLE
14 MASTER VOLUME
1. Interface connectors for BEACON SENSOR, MUTE SENSOR and ALERT OUT ports are
provided with the unit.
2. Item sold separately or as part of a MP-FS100_PAK or MP-FS200_PAK system package.
Rotary high frequency boost/cut adjustment
Rotary master level adjustment
Operations & Installation Guide – DOC. 7164B Single/Dual-Channel Wireless Mic Receiver: MP-FS-RX1/RX2 • 7
Page 12
Single/Dual-Channel Wireless Mic Receiver Crestron MP-FS-RX1/RX2
Setup
Installation
The MP-FS-RX1/RX2 can be placed on any convenient flat surface in the room,
such as a desk, shelf, table, or ceiling-mounted third-party equipment platform.
• Install all accessory hardware, including power pack, MP-FSIR Beacon
Sensor(s), MP-FS-PAS Audio Sensor, FS6 or FSDI8 speakers, following
their supplied instructions.
• For the MP-FS-RX1, attach the supplied single antenna; for the
MP-FS-RX2, attach the cables from the two supplied antennas (the antennas
should be spaced at least 6 feet (~ 2 meters) apart.
• Orientation of antennas for desk, shelf, or table mounting installations
should be straight up. For ceiling mounted installations (including the
MP-FS-RX1 on a third-party ceiling-mounted equipment platform), antenna
orientation should be straight down. For wall-mounted installations, the
antennas should be at a 45° angle, either up or down, from the wall.
• Install all other required interconnecting cables.
Hardware Hookup
Make the necessary connections as called out in the illustration that follows this
paragraph. Apply power after all connections have been made.
When making connections to the MP-FS-RX1/RX2, use Crestron power supplies for
Crestron equipment.
Hardware Connections for the MP-FS-RX1/RX2
NOTE: Ensure the unit is properly grounded by connecting the chassis ground lug
to an earth ground (building steel).
8 • Single/Dual-Channel Wireless Mic Receiver: MP-FS-RX1/RX2 Operations & Installation Guide – DOC. 7164B
Page 13
Crestron MP-FS-RX1/RX2 Single/Dual-Channel Wireless Mic Receiver
USB
PC Running
Crestron Toolbox
MP-FS-RX1/RX2
Uploading and Upgrading
Crestron recommends that each device contains the latest firmware to take advantage
of the most recently released features. However, before attempting to upload or
upgrade it is necessary to establish communication. Once communication has been
established, firmware can be transferred to the device.
Establishing Communication
Use Crestron Toolbox™ for communicating with the MP-FS-RX1/RX2; refer to the
Crestron Toolbox help file for details. There is a single method of communication:
USB communication.
USB Communication
The COMPUTER port on the MP-FS-RX1/RX2 connects to the USB port on the
PC via the included Type A to Type B USB cable:
1. Use the Address Book in Crestron Toolbox to create an entry using the
expected communication protocol (USB).
2. Display the MP-FS-RX1/RX2’s “System Info” window (click the
icon); communications are confirmed when the device information is
displayed.
Firmware
Firmware files may be distributed from programmers to installers or from Crestron
to dealers. Firmware upgrades are available from the Crestron Web site as new
features are developed after product releases. Upgrade via the Crestron Toolbox. For
details on upgrading, refer to the Crestron Toolbox help file.
Operations & Installation Guide – DOC. 7164B Single/Dual-Channel Wireless Mic Receiver: MP-FS-RX1/RX2 • 9
Page 14
Single/Dual-Channel Wireless Mic Receiver Crestron MP-FS-RX1/RX2
Operation
Basic Procedures
Before beginning, ensure that the MP-FS-RX1/RX2 receiver is installed and
connected as instructed in “Setup” on page 8, that power is on (the green LED is on),
that line level audio is supplied from a DVD player, a laptop computer, or other
device, and that the MP-FSMIC microphone has been fully charged.
Microphone Button/LED Functions
During the following verification procedures, refer to the illustration above.
Pair Microphone with Receiver
1. Hold the MP-FSMIC ON button until the mic Status LED rapidly flashes green.
2. The mic begins pairing with the receiver. Make sure the mic has line of sight
proximity to the MP-FSIR. When pairing is complete, the Status LED slowly
blinks green. Time to pair is typically between 5 and 10 seconds. The mic must
be turned off and turned on again to pair to another receiver.
Mute and Volume Adjustments
1. Press the MUTE button to mute the mic (observe the blink pattern); press it
again to un-mute. When muted, the mic automatically turns off after 2 minutes.
2. When the mic is not muted, the VOL button can be used to adjust the mic
volume.
3. When the mic is muted, the VOL button adjusts the line level audio volume.
4. Line volume is automatically “ducked” (reduced) when the user talks into the
mic.
5. Hold the MUTE button for 5 seconds to turn off the mic (turns off automatically
if muted for 2 minutes, or when placed in the charger.)
6. If the mic loses sight of the MP-FSIR for 7 seconds (time is configurable), the
mic automatically mutes (turns off automatically if muted for 2 minutes).
7. If RF link is lost for 10 seconds, mic turns off.
Emergency Trigger
Hold the ALERT button for 8 seconds (time is configurable) to generate two beeps
from the speakers and close the alert relay contacts until the button is released.
10 • Single/Dual-Channel Wireless Mic Receiver: MP-FS-RX1/RX2 Operations & Installation Guide – DOC. 7164B
Page 15
Crestron MP-FS-RX1/RX2 Single/Dual-Channel Wireless Mic Receiver
Receiver Controls - Default Settings
BASS and TREBLE: Typically, set these controls to their center detent positions.
Slightly reducing treble can help to reduce feedback.
MASTER VOLUME: Have the instructor speak from the most likely position in the
room and adjust this control clockwise so that the speakers just begin to exhibit
feedback, and then reduce the setting slightly by turning counterclockwise.
Operations & Installation Guide – DOC. 7164B Single/Dual-Channel Wireless Mic Receiver: MP-FS-RX1/RX2 • 11
Page 16
Single/Dual-Channel Wireless Mic Receiver Crestron MP-FS-RX1/RX2
Problem Solving
Troubleshooting
The following table provides corrective action for possible trouble situations. If
further assistance is required, please contact a Crestron customer service
representative.
MP-FS-RX1/RX2 Troubleshooting
TROUBLE POSSIBLE CAUSE(S) CORRECTIVE ACTION
Mic mutes. Loss of IR signal Make certain beacon sensor
is not mounted near window
or lighting fixture.
Make certain IR beacon LEDs
are not blocked by clothing or
by being held.
Low battery Charge the mic.
High-pitch noise
(feedback)
Poor sound
quality.
For MP-FS-RX2,
Mic is picking up sound
from speakers
Cables improperly
connected.
antennas not 6 feet (2
meters) apart.
Turn down mic volume,
decrease master volume,
move speakers to a location
that the mic is not typically
close to, e.g., the back of the
room.
Verify all cables are secure.
Adjust antenna spacing to 6
feet (2 meters) minimum.
Further Inquiries
To locate specific information or to resolve questions after reviewing this guide,
contact Crestron's True Blue Support at 1-888-Crestron [1-888-273-7876] or refer to
the listing of Crestron worldwide offices on the Crestron Web site
(www.crestron.com/offices
) for assistance within a particular geographic region.
To post a question about Crestron products, log onto the Online Help section of the
Crestron Web site (www.crestron.com/onlinehelp
). First-time users must establish a
user account to fully benefit from all available features.
Future Updates
As Crestron improves functions, adds new features and extends the capabilities of
the MP-FS-RX1/RX2, additional information may be made available as manual
updates. These updates are solely electronic and serve as intermediary supplements
prior to the release of a complete technical documentation revision.
Check the Crestron Web site periodically for manual update availability and its
relevance. Updates are identified as an “Addendum” in the Download column.
12 • Single/Dual-Channel Wireless Mic Receiver: MP-FS-RX1/RX2 Operations & Installation Guide – DOC. 7164B
Page 17
Crestron MP-FS-RX1/RX2 Single/Dual-Channel Wireless Mic Receiver
Return and Warranty Policies
Merchandise Returns / Repair Service
1. No merchandise may be returned for credit, exchange or service without prior authorization
from Crestron. To obtain warranty service for Crestron products, contact an authorized
Crestron dealer. Only authorized Crestron dealers may contact the factory and request an
RMA (Return Merchandise Authorization) number. Enclose a note specifying the nature of
the problem, name and phone number of contact person, RMA number and return address.
2. Products may be returned for credit, exchange or service with a Crestron Return Merchandise
Authorization (RMA) number. Authorized returns must be shipped freight prepaid to
Crestron, 6 Volvo Drive, Rockleigh, N.J. or its authorized subsidiaries, with RMA number
clearly marked on the outside of all cartons. Shipments arriving freight collect or without an
RMA number shall be subject to refusal. Crestron reserves the right in its sole and absolute
discretion to charge a 15% restocking fee plus shipping costs on any products returned with
an RMA.
3. Return freight charges following repair of items under warranty shall be paid by Crestron,
shipping by standard ground carrier. In the event repairs are found to be non-warranty, return
freight costs shall be paid by the purchaser.
Crestron Limited Warranty
Crestron Electronics, Inc. warrants its products to be free from manufacturing defects in materials and
workmanship under normal use for a period of three (3) years from the date of purchase from Crestron,
with the following exceptions: disk drives and any other moving or rotating mechanical parts, pan/tilt heads
and power supplies are covered for a period of one (1) year; touch screen display and overlay components
are covered for 90 days; batteries and incandescent lamps are not covered.
This warranty extends to products purchased directly from Crestron or an authorized Crestron dealer.
Purchasers should inquire of the dealer regarding the nature and extent of the dealer's warranty, if any.
Crestron shall not be liable to honor the terms of this warranty if the product has been used in any
application other than that for which it was intended or if it has been subjected to misuse, accidental
damage, modification or improper installation procedures. Furthermore, this warranty does not cover any
product that has had the serial number altered, defaced or removed.
This warranty shall be the sole and exclusive remedy to the original purchaser. In no event shall Crestron
be liable for incidental or consequential damages of any kind (property or economic damages inclusive)
arising from the sale or use of this equipment. Crestron is not liable for any claim made by a third party or
made by the purchaser for a third party.
Crestron shall, at its option, repair or replace any product found defective, without charge for parts or labor.
Repaired or replaced equipment and parts supplied under this warranty shall be covered only by the
unexpired portion of the warranty.
Except as expressly set forth in this warranty, Crestron makes no other warranties, expressed or implied,
nor authorizes any other party to offer any warranty, including any implied warranties of merchantability or
fitness for a particular purpose. Any implied warranties that may be imposed by law are limited to the terms
of this limited warranty. This warranty statement supersedes all previous warranties.
Operations & Installation Guide – DOC. 7164B Single/Dual-Channel Wireless Mic Receiver: MP-FS-RX1/RX2 • 13
Page 18
Single/Dual-Channel Wireless Mic Receiver Crestron MP-FS-RX1/RX2
This page is intentionally left blank.
14 • Single/Dual-Channel Wireless Mic Receiver: MP-FS-RX1/RX2 Operations & Installation Guide – DOC. 7164B
Page 19
Crestron MP-FS-RX1/RX2 Single/Dual-Channel Wireless Mic Receiver
This page is intentionally left blank.
Operations & Installation Guide – DOC. 7164B Single/Dual-Channel Wireless Mic Receiver: MP-FS-RX1/RX2 • 15
Page 20
Crestron Electronics, Inc. Operations & Installation Guide – DOC. 7164B
15 Volvo Drive Rockleigh, NJ 07647 (2030215)
Tel: 888.Crestron 08.12
Fax: 201.767.7576 Specifications subject to
www.crestron.com change without notice.
Loading...