DO GUIDE
To return to the previous
“MenuBack” button.
To highlight an item, turn
the scroll wheel until the
select a highlighted item,
ML X-3
Color LCD Handheld Wireless Remote with inNET EX
DO Check the Box
QTY PRODUCT COLOR PART NUM.
2 Batteries, AA, Alkaline 2032967
®
1 Cable, USB 2.0, A-B, 6' 6" (2 m) Black 20 25146
DO Install the Batteries
Install the four included AA alkaline batteries
as shown in the diagram located inside the
battery compartment.
CAUTION : Replace all batteries in the
MLX-3 at the same time. Mixing old and new
batteries may result in battery leakage and
equipment damage.
NOTE: Do not use rechargeable batteries.
To extend battery life, Crestron®
recommends the following:
• Use Lithium batteries.
• Maintain the default backlight and key
brightness level settings (the default is
25%) or use lower settings.
• For installations where the remote will
not be used in dark locations, setting
the keyback backlight level to 0 results
in even longer battery life.
DO Navigate the MLX-3
The MLX-3 uses a scroll wheel and a
“MenuBack” button to allow navigation
through the LCD display.
DO Acquire the MLX-3
Before the MLX-3 can be used, it must rst
be acquired by a CEN-RFGW-EX gateway
(sold separately) that is connected to an
inNET EX® system.
NOTE: An inNET EX device can be
acquired by only one gateway.
To acquire the MLX-3, perform the following
procedure:
1. Put the CEN-RFGW-EX in Acquire mode
by pressing its ACQUIRE button (on the
unit itself or from Crestron Toolbox™).
The gateway’s ACQUIRE LED lights.
2. From the ML X-3’s Setup Options
screen, turn the scroll wheel to highlight
Radio and then press the scroll wheel.
3. Turn the scroll wheel to highlight
Acquire and then press the scroll wheel.
4. Turn the scroll wheel to highlight Yes
and then press the scroll wheel.
5. Press the scroll wheel to begin the
aqcuire process.
6. When the MLX-3 indicates the acquire
has completed successfully, press
the scroll wheel to take the MLX-3 out
of Acquire mode and to return to the
Radio Options screen. Then, press the
“MenuBack” button to exit the Radio
Options screen.
DO Access the Setup Screens
When power is applied for the rst time, the
following screen appears.
Press the SELECT button or the scroll wheel
(or press MEDIA, LIGHTS, , and GUIDE
in sequence twice within a 5 second period)
to display the Setup Options screen. The
buttons on the Setup Options screen enable
basic conguration prior to regular operation
of the MLX-3.
NOTE: To access the setup screens during
regular operation of the MLX-3, press
MEDIA, LIGHTS, , and GUIDE in
sequence twice within a 5 second period.
MEDIA
GUIDE
LIGHTS
LISTMENU
desired item is bold. To
press the scroll wheel.
screen, press the
7. Take the CEN-RFGW-EX out of Acquire
mode by pressing its ACQUIRE button.
The USB port for upgrading firmware is
located behind the battery compartment
cover on the rear of the unit.
DO Learn More
Visit the website for additional
information and the latest rmware
updates.
Crestron Electronics
15 Volvo Drive, Rockleigh, NJ 07647
888.CRESTRON | www.crestron.com
As of the date of manufactur e, the pro duct ha s been te sted an d found to comply with spec ications for C E marking.
Federal Communications Commission (FCC) Compliance Statement
This device complies with par t 15 of the FCC Rul es. Operatio n is subject to the following two conditions:
(1) This devic e may not ca use har mful interfe rence, and (2) this device must acc ept any in terfe rence received, incl uding in terference
that may cause undesired operation.
Caution: Chang es or modications not expres sly app roved by the manufa cture r respo nsible for comp liance could void the user’s
author ity to op erate th e equipment.
Note: This equipment has been tested an d found to c omply with the limits for a Class B digital device, pu rsuant to par t 15 of the
FCC Rules. These limits a re desi gned to provide re asonable protectio n against harm ful inte rference in a residential in stallation.
This equipment generates, uses and c an radi ate radio frequency energy and, if not installe d and used in acc ordance with th e
instruction s, may cause harmful inte rference to radio communic ations. However, there is no guarante e that interference will not
occur in a particular i nstallation.
If this equipment does cause harmful interference to radio or televis ion rec eption, which can be dete rmine d by turni ng the
equipment off and on, th e user is e ncouraged to try to correct the inter ference by one or more of the followi ng meas ures:
• Reorient or relocate the receiving antenna
• Increase the separ ation between the equi pment a nd rece iver
• Connect the e quipment into an outlet o n a circuit different from that to which the receiver is con necte d
• Consult the dealer or an experienced radio/T V technician fo r help
Industry Canada (IC) Compliance Statement
This device complies with Industry Canada license -exempt RSS standard(s). Operation is subject to the following t wo condi tions:
(1) this device may not cause interference and (2) this dev ice must accept any interfere nce, including inter ference that may cause
undesired operation of the device.
DO GUIDE
Under Industr y Canada regulations, this ra dio transmit ter may only oper ate usin g an antenna of a type and ma ximum (o r lesser)
gain approved for the tran smitter by Indu stry C anada . To reduce potential radio interfe rence to other us ers, the antenna type a nd
its gain s hould b e so chos en that th e equiva lent is otropically r adiate d power (e.i.r.p.) is not more than that n ecessary for succ essful
communication.
Industrie Canada (IC) Déclaration de conformité
Le présent appareil est confo rme aux CNR d’Industrie Canada applicables aux appareils ra dio exempts de licence. L’exploitation
est auto risée aux deux c onditions suivantes : (1) l’appa reil ne doit pas produire de brouillage, e t (2) l’utilisateur de l’appareil doit
accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
Confor mément à la régl ement ation d’Indust rie Canada, le présent émetteur radio peut fo nctionner avec une antenne d’un ty pe et
d’un gain ma xima l (ou infér ieur) a pprou vé pour l’éme tteur p ar Industrie Ca nada. D ans le bu t de rédu ire les risques de brouillage
radioé lectrique à l’in tention des autres utilisateu rs, il faut choisir le ty pe d’antenn e et son ga in de sor te que la p uissance isotrope
rayonné e équivalente ( p.i.r.e.) ne dépa sse pas l’intensité néce ssaire à l’établisseme nt d’une co mmunication s atisfaisante.
Crestr on produc t developmen t soft ware is licen sed to Cres tron deal ers and Cre stron Se rvice Pr oviders (C SPs) und er a limited non -exclusive , non-tra nsferabl e Soft ware Devel opment Tools
License A greement. Cre stron produc t operating sys tem softwa re is licensed to C restron deale rs, CSPs, a nd end-users un der a separate En d-User Lice nse Agreement . Both of these A greements
can be found on the Crestron website at www.crestron.com/legal/software_license_agreement.
The speci c patents that c over Crestron pro ducts are listed a t patents.crestron.com. The produ ct warranty ca n be found at www.crestron.com/warranty.
Crestr on, the Cre stron log o, Crestron Toolbox, an d inNET EX are e ither trademarks or r egistered tradema rks of Cres tron Electronic s, Inc., in the United S tates and /or other countrie s. Other
trademar ks, regis tered tra demarks, a nd trade nam es may be used in t his documen t to refer to ei ther the en tities cla iming the mark s and names or t heir produ cts. Cre stron dis claims any
propriet ary interest in t he marks and names of o thers. Crestr on is not responsib le for errors in ty pography or photo graphy.
This docum ent was written by t he Technical Publicat ions departmen t at Crestron.
©2015 Crestron Electronics, Inc.
DOC. 775 6A (2043232) 0 4.15
Specic ations subject to c hange without not ice.
Loading...