AIR_SR4/SR6/SR8
AIR® 2-Way Surface Mount Outdoor Speakers
®
speakers by Crestron® offer superior sound quality and flexible
AIR
installation in a range of popular sizes for all types of indoor and outdoor
applications. Solid construction and high end components are hallmarks
of the complete AIR speaker line. Each AIR model provides a pair of
weatherized 2-way surface mount outdoor loudspeakers with polypropylene
woofers for deep, solid bass, optimized dual front ports for enhanced low
frequency response, and titanium dome tweeters for crisp, clear high end
extension.
Featuring a unique “QuickBall” mounting system, the AIR speakers can be
mounted to any solid flat surface, with the ability to orient and aim the speaker
in virtually any position. The QuickBall bracket achieves a very clean and
stable installation using a tool-free ball-and-socket mechanism. Simply
position the speaker as desired and flip the clamp lever closed. A security
screw is included to deter theft by preventing the lever from being released.
quickstart guide
AIR speakers, supplied in pairs, are available in black or white and can be
painted to blend with the surrounding architecture.
NOTE: Before starting installation, ensure the wall and wall material are capable of supporting the
combined weight of the speakers and the wall mount assemblies. Refer to section ➌ "Specifications"
for weights.
2
Physical Views (AIR_SR8 Shown)
Front View
(Grill Removed)
Side View
2.16 in
(55 mm)
10.73 in
(273 mm
Rear View
(Mounting Bracket
Removed)
)
9.57 in
(244 mm)
13.31 in
(338 mm)
Bottom View
6.94 in
(177 mm)
9.05 in
(230 mm)
Installation
1
Refer to the illustration to the right as necessary, and install the speakers as
follows:
1. Route the cables from the audio source to the intended speaker locations
following all appropriate local codes.
2. Attach the QuickBall mounting bracket directly to the wall or to a flush
mounted 1-gang US, UK, or European electrical box, allowing the cable
coming through the wall (and the electrical box, if used) to exit through the
speaker cable access hole of the mounting bracket.
NOTE: If the mounting bracket is to be attached to an electrical box, be
sure it is also attached to surrounding framing, to provide the support
needed to hold the weight of the speaker.
The QuickBall mounting bracket can also be mounted to a light pole or post
using pole mounting straps (not included).
3. Detach the 4-pin screw terminal block connector from the speaker. Connect
the audio source’s + and - outputs to the connector’s outer + and - (IN)
terminals. Maximum wire size is 12 AWG. Use the inner + and - (THRU)
terminals to connect a second speaker in parallel.
NOTE: The number of speakers that can be added is limited only by the
specifications of the amplifier.
a. Strip the wires 1/4 in (~6 mm), twist the strands, insert them into
the terminal block, and tighten the screws to secure them.
b. Reattach the terminal block to the speaker connector.
4. Carefully mount the speaker on the QuickBall mounting bracket,
rotate and set the speaker at the desired angle, and raise the ball
socket clamp lever into position against the bottom of the speaker.
Use the supplied security screw to prevent the lever from being
accidentally pulled, releasing the speaker.
5. Attach a security cable (SPKA-ST-15, sold separately) to the security
cable attachment point. The other end of the cable must be attached
to a secondary support point, able to support several times the weight
of the speaker.
Security
Cable
Attachment
Point
Security
Screw
Ball Socket
Clamp Lever
Detachable
Screw Terminal Block
+ + - -
QuickBall
Mounting
Bracket
Speaker
Cable
Access
Hole
From
Audio
Source
AIR_SR4/SR6/SR8
IN
THRU
To
Parallel
Speaker
1
QUICKSTART DOC. 7129B (2029452) 08.13
www.crestron.com
Specifications subject to
change without notice.
888.273.7876 201.767.3400
AIR_SR4/SR6/SR8
AIR® 2-Way Surface Mount Outdoor Speakers
3
Specifications
AIR_SR4/SR6/SR8 Specifications
SPECIFICATION AIR_SR4
Drivers
Woofer
Tweeter
Crossover Frequency
Impedance
Frequency Range
Frequency Response
quickstart guide
Power Handling
Sensitivity
Environmental
Temperature
Humidity
Construction
Enclosure
Grill
Mounting
Positioning
Yaw (Horizontal)
Pitch (Vertical)
Roll
Dimensions
Height
Width
Depth
Weight
4 inch (102 mm) polypropylene with
rubber surround and steel basket
0.79 inch (20 mm) titanium dome
2.5 kHz
8 Ω nominal
65 Hz to 20 kHz (-10 dB)
70 Hz to 20 kHz (±3 dB)
100 watts program
87 dB @ 1W/1m
-2º to 120º F (-19º to 49º C)
5% to 95% RH (non-condensing)
ABS plastic, textured finish, paintable
Aluminum, powder coated, paintable
Surface mount to a solid flat surface
with option to position over a
flush-mounted 1-gang electrical box,
1-gang UK (BS 4662) electrical box, or
1-gang European (DIN 49073)
electrical box; pole mount (straps not
included); rigging point for safety tether
(SPKA-ST-15 sold separately);
theft-resistant security screw
± 30°
± 30°
360°
8.67 in (220 mm)
5.91 in (151 mm)
6.55 in (167 mm), 8.66 in (220 mm)
with mounting bracket
4.5 lb (~2 kg)
AIR_SR6 AIR_SR8
6 inch (153 mm) polypropylene with
rubber surround and steel basket
0.98 inch (25 mm) titanium dome
2 kHz
8 Ω nominal
55 Hz to 20 kHz (-10 dB)
60 Hz to 20 kHz (±3 dB)
150 watts program
88.5 dB @ 1W/1m
-2º to 120º F (-19º to 49º C)
5% to 95% RH (non-condensing)
ABS plastic, textured finish, paintable
Aluminum, powder coated, paintable
Surface mount to a solid flat surface
with option to position over a
flush-mounted 1-gang electrical box,
1-gang UK (BS 4662) electrical box, or
1-gang European (DIN 49073)
electrical box; pole mount (straps not
included); rigging point for safety tether
(SPKA-ST-15 sold separately);
theft-resistant security screw
± 30°
± 30°
360°
11.19 in (284 mm)
8.08 in (205 mm)
6.75 in (172 mm), 8.86 in (225 mm)
with mounting bracket
6.6 lb (~3 kg)
8 inch (203 mm) polypropylene with
rubber surround and steel basket
0.98 inch (25 mm) titanium dome
2 kHz
8 Ω nominal
50 Hz to 20 kHz
55 Hz to 20 kHz (±3 dB)
200 watts program
89.5 dB @ 1W/1m
-2º to 120º F (-19º to 49º C)
5% to 95% RH (non-condensing)
ABS plastic, textured finish, paintable
Aluminum, powder coated, paintable
Surface mount to a solid flat surface
with option to position over a
flush-mounted 1-gang electrical box,
1-gang UK (BS 4662) electrical box, or
1-gang European (DIN 49073)
electrical box; pole mount (straps not
included); rigging point for safety tether
(SPKA-ST-15 sold separately);
theft-resistant security screw
± 30°
± 30°
360°
13.31 in (338 mm)
9.57 in (243 mm)
6.94 in (177 mm), 9.05 in (230 mm)
with mounting bracket
8.7 lb (~4 kg)
4
Problem Solving
Troubleshooting
The following table provides corrective action for possible trouble situations. If further assistance is
required, please contact a Crestron customer service representative.
TROUBLE POSSIBLE CAUSE(S)
No sound or intermittent
sound from speakers.
Constant noise such as
buzz, hum or hiss from
speakers.
Poor low frequency
output.
Further Inquiries
To locate specific information or resolve questions after reviewing this guide, contact Crestron's
True Blue Support at 1-888-CRESTRON [1-888-273-7876] or, for
assistance within a particular geographic region, refer to the listing of Crestron
worldwide offices at www.crestron.com/offices.
To post a question about Crestron products, log onto Crestron’s Online Help at
www.crestron.com/onlinehelp. First-time users must establish a user account to fully benefit from
all available features.
Future Updates
As Crestron improves functions, adds new features and extends the capabilities of the
AIR_
SR4/SR6/SR8 speakers
These updates are solely electronic and serve as intermediary supplements prior to the release of
a complete technical documentation revision.
Check the Crestron Web site periodically for manual update availability and its relevance. Updates
are identified as an “Addendum” in the Download column.
Cable connection error. Verify cable connections between amplifier
Amplifier not receiving
input signal or amplifier
malfunction.
Faulty device in system.
System grounding fault.
Incorrect polarity
connection at speaker or
amplifier.
, additional information may be made available as manual updates.
CORRECTIVE ACTION
and speakers.
Verify amplifer is functioning correctly, that
it is receiving an input signal and that
correct input source is selected.
Verify all devices in system are functioning
properly.
Verify system grounding.
Verify speaker connection polarity (i.e. +
on amplifier to + on speaker).
AIR_SR4/SR6/SR8
2
QUICKSTART DOC. 7129B (2029452) 08.13
www.crestron.com
Specifications subject to
change without notice.
The specific patents that cover Crestron products are listed at patents.crestron.com.
Crestron, the Crestron logo, and AIR are either trademarks or registered trademarks of Crestron Electronics, Inc. in the United States and/or
other countries. Other trademarks, registered trademarks, and trade names may be used in this document to refer to either the entities
claiming the marks and names or their products. Crestron disclaims any proprietary interest in the marks and names of others. Crestron is
not responsible for errors in typography or photography.
This document was written by the Technical Publications department at Crestron.
©2013 Crestron Electronics, Inc.
888.273.7876 201.767.3400
Loading...