Craftsman 917.275400 User Manual

Download

Page 1

Owner’s Manual

LAWN TRACTOR

18.0 HR 42” Mower Electric Start

Automatic Transmission

Model No.

917.275400

This product has a low emission engine which operates differently from previously built engines. Before you start the engine, read and understand this Owner’s Manual.

IMPORTANT:

Read and follow all Safety Rules and Instructions before

operating this equipment.

Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A

Visit our Craftsman website:www.sears.com/craftsman

For answers to your questions

about this product, Call:

1-800-659-5917

Sears Craftsman Help Line

5 am - 5 pm, Mon - Sat

Page 2

TABLE OF CONTENTS

Warranty Safety Rules Product Specifications... AssemblyPre-Operation

Operation........................ ......................11

Maintenance

.........................

...................

..................

........................

......................17

2 3 6 8

Maintenance Schedule

Service and Adjustments.... .................22

Storage

Troubleshooting

Repair Parts..........................................34

Sears Service

................................

...................

......................

........

.................17

.................28

.................29

...Back Cover

WARRANTY

LIMITED WARRANTY ON CRAFTSMAN RIDING EQUIPMENT For two (2) years from the date of purchase, if this Craftsman Riding Equipment is maintained, lubricated and tuned up according to the instructions in the owner’s manual, Sears will repair or replace free of charge any parts that are found to be defective in material or workmanship according to the guidelines of coverage listed below. Sears will also provide free labor for these applicable warranted parts for the two full years. During the first 30 days of purchase, there will be no charges to service the product at your home for issues covered by this warranty. (See exclusions below). For your conve nience, IN HOME warranty service will still be available after the first 30 days of pur chase, but a trip charge will apply. This charge will be waived if the Craftsman product is dropped off at an authorized Sears location. For the nearest authorized Sears location, please call 1-800-4-MY-HOME®. This warranty applies only while this product is within the United States.

This Warranty does not cover:

• Expendable items which become worn during normal use, including but not limited to blades, spark plugs, air cleaners, belts, and oil filters.

• Standard Maintenance Servicing, oil changes, or tune-ups

• Tire replacement or repair caused by punctures from outside objects, such as nails, thorns, stumps, or glass.

• Repairs necessary because of operator abuse, including but not limited to, damage caused by towing objects beyond the capability of the riding equipment, impacting objects that bend the frame or crankshaft, or over-speeding the engine.

• Repairs necessary because of operator negligence, including but not limited to, elec trical and mechanical damage caused by improper storage, failure to use the proper grade and amount of engine oil, failure to keep the deck clear of flammable debris, or failure to maintain the equipment according to the instructions contained in the owner’s manual.

• Engine (fuel system) cleaning or repairs caused by fuel determined to be contami nated or oxidized (stale). In general, fuel should be used within 30 days of its pur chase date.

• Normal deterioration and wear of the exterior finishes, or product label replacement.

• Riding equipment used for commercial or rental purposes.

LIMITED WARRANTY ON BATTERY For ninety (90) days from date of purchase, if any battery included with this riding equip

ment proves defective in material or workmanship and our testing determines the battery will not hold a charge, Sears will replace the battery at no charge. During the first 30 days of purchase, there will be no charges to replace the battery at your HOME. After the first 30 days, for your convenience, IN-HOME warranty service will still be avail

able but a trip charge will apply. This charge will be waived if the Craftsman product is dropped off at an authorized Sears location. For the nearest authorized Sears location,

please call 1-800-4-MY-HOME®. This battery warranty applies only while this product is within the United States. This warranty gives you specific legal rights, and you may also have other rights, which

vary, from state to state.

Sears, Roebuck and Co.,Dept.817WA, Hoffman Estates, IL 60179

Page 3

SAFETY RULES

IMPORTANT: This cutting machine is capable of amputating hands and feet and throw

ing objects. Failure to observe the following safety instructions could result in serious injury or death.

WARNING: In order to prevent ac

cidental starting when setting up, trans

porting, adjusting or making repairs, always disconnect spark plug wire and place wire where it cannot contact spark

plug.

WARNING: Do not coast down a hill in

neutral, you may lose control of the tractor.

WARNING: Tow only the attachments

that are recommended by and comply with specifications of the manufacturer of your tractor. Use common sense when towing. Operate only at the lowest possible speed

when on a slope. Too heavy of a load, while on a slope, is dangerous. Tires can

lose traction with the ground and cause you to lose control of your tractor.

WARNING: Engine exhaust, some of

its constituents, and certain vehicle com ponents contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.

WARNING: Battery posts, terminals

and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.

Wash hands after handling.

I. GENERAL OPERATION

• Read, understand, and follow all

instructions on the machine and in the manual before starting.

• Do not put hands or feet near rotating

parts or under the machine. Keep clear of the discharge opening at all times.

• Only allow responsible adults, who are

familiar with the instructions, to operate the machine.

• Clear the area of objects such as

rocks, toys, wire, etc., which could be picked up and thrown by the blades.

• Be sure the area is clear of bystand

ers before operating. Stop machine if anyone enters the area.

• Never carry passengers.

• Do not mow in reverse unless abso

lutely necessary. Always look down and behind before and while backing.

Never direct discharged material

toward anyone. Avoid discharging

material against a wall or obstruction. Material may ricochet back toward the

operator. Stop the blades when cross

ing gravel surfaces.

Do not operate machine without the entire grass catcher, discharge guard, or other safety devices in place and working. Slow down before turning.

Never leave a running machine unattended. Always turn off blades, set parking brake, stop engine, and

remove keys before dismounting.

Disengage blades when not mowing. Shut off engine and wait for all parts to come to a complete stop before clean

ing the machine, removing the grass catcher, or unclogging the discharge guard. Operate machine only in daylight or good artificial light.

Do not operate the machine while under the influence of alcohol or drugs. Watch for traffic when operating near or crossing roadways.

Use extra care when loading or un

loading the machine into a trailer or truck. Always wear eye protection when oper ating machine.

Data indicates that operators, age 60 years and above, are involved in a

large percentage of riding mower-re

lated injuries. These operators should evaluate their ability to operate the

riding mower safely enough to protect themselves and others from serious

injury.

Follow the manufacturer’s recommen dation for wheel weights or counter weights.

Keep machine free of grass , leaves or other debris build-up which can touch

hot exhaust / engine parts and burn.

Do not allow the mower deck to plow

leaves or other debris which can cause build-up to occur. Clean any oil or fuel spillage before operating or storing the

machine. Allow machine to cool before storage.

Page 4

SAFETY RULES

II. SLOPE OPERATION

Slopes are a major factor related to loss of control and tip-over accidents, which can result in severe injury or death. Opera tion on ail slopes requires extra caution. If you cannot back up the slope or if you feel uneasy on it, do not mow it.

• Mow up and down slopes, not across.

• Watch for holes, ruts, bumps, rocks, or other hidden objects. Uneven terrain could overturn the machine. Tall grass can hide obstacles.

• Choose a low ground speed so that you will not have to stop or shift while on the slope.

• Do not mow on wet grass. Tires may lose traction. Always keep the machine in gear when going down slopes. Do not shift to neutral and coast downhill.

• Avoid starting, stopping, or turning on a slope. If the tires lose traction, dis engage the blades and proceed slowly straight down the slope.

• Keep all movement on the slopes slow and gradual. Do not make sudden changes in speed or direction, which could cause the machine to roll over.

• Use extra care while operating ma chine with grass catchers or other at tachments; they can affect the stability of the machine. Do no use on steep slopes.

• Do not try to stabilize the machine by putting your foot on the ground.

• Do not mow near drop-offs, ditches, or embankments. The machine could suddenly roll over if a wheel is over the edge or if the edge caves in.

III. CHILDREN

Tragic accidents can occur if the operator is not alert to the presence of children. Children are often attracted to the machine and the mowing activity. Never assume that children will remain where you last saw them.

• Keep children out of the mowing area and in the watchful care of a respon sible adult other than the operator.

• Be alert and turn machine off if a child enters the area.

• Before and while backing, look behind and down for small children.

• Never carry children, even with the blades shut off. They may fall off and be seriously injured or interfere with safe machine operation. Children who

have been given rides in the past may suddenly appear in the mowing area for another ride and be run over or backed over by the machine.

• Never allow children to operate the machine.

• Use extra care when approaching blind

corners, shrubs, trees, or other objects that may block your view of a child.

IV. TOWING

• Tow only with a machine that has a hitch designed for towing. Do not at

tach towed equipment except at the

hitch point.

• Follow the manufacturer’s recom mendation for weight limits for towed

equipment and towing on slopes.

• Never allow children or others in or on

towed equipment.

• On slopes, the weight of the towed

equipment may cause loss of traction and loss of control.

• Travel slowly and allow extra distance

to stop.

V. SERVICE

SAFE HANDLING OF GASOLINE

To avoid personal injury or property damage, use extreme care in handling gasoline. Gasoline is extremely flammable and the vapors are explosive.

• Extinguish all cigarettes, cigars, pipes,

and other sources of ignition.

• Use only approved gasoline container.

• Never remove gas cap or add fuel with

the engine running. Allow engine to cool before refueling.

• Never fuel the machine indoors.

• Never store the machine or fuel con

tainer where there is an open flame, spark, or pilot light such as on a water

heater or other appliances.

• Never fill containers inside a vehicle

or on a truck or trailer bed with plastic

liner. Always place containers on the

ground away from your vehicle when filling.

Page 5

SAFETY RULES

• Remove gas-powered equipment from the truck or trailer and refuel it on the ground. If this is not possible, then refuel such equipment with a portable container, rather than from a gasoline dispenser nozzle.

• Keep the nozzle in contact with the rim of the fuel tank or container opening at all times until fueling is complete. Do not use a nozzle lock-open device.

• If fuel is spilled on clothing, change clothing immediately.

• Never overfill fuel tank. Replace gas cap and tighten securely.

GENERAL SERVICE

• Never operate machine in a closed are.

• Keep all nuts and bolts tight to be sure the equipment is in safe working condi tion.

• Never tamper with safety devices. Check their proper operation regularly.

Keep machine free of grass, leaves, or other debris build-up. Clean oil or fuel spillage and remove any fuel-soaked debris. Allow machine to cool before storing.

If you strike a foreign object, stop and inspect the machine. Repair, if neces sary, before restarting. Never make any adjustments or repairs with the engine running. Check grass catcher components and the discharge guard frequently and replace with manufacturer’s recom mended parts, when necessary. Mower blades are sharp. Wrap the blade or wear gloves, and use extra caution when servicing them. Check brake operation frequently. Ad

just and service as required.

Maintain or replace safety and instruc tion labels, as necessary.

Be sure the area is clear of bystand ers before operating. Stop machine if anyone enters the area. Never carry passengers. Do not mow in reverse unless abso lutely necessary. Always look down and behind before and while backing. Never carry children, even with the blades shut off. They may fall off and be seriously injured or interfere with safe machine operation. Children who have been given rides in the past may suddenly appear in the mowing area for another ride and be run over or backed over by the machine. Keep children out of the mowing area and in the watchful care of a respon sible adult other than the operator. Be alert and turn machine off if a child enters the area.

Before and while backing, look behind

and down for small children.

Mow up and down slopes (15° Max),

not across. Choose a low ground speed so that you will not have to stop or shift while on the slope. Avoid starting, stopping, or turning on a slope. If the tires lose traction, dis engage the blades and proceed slowly straight down the slope.

If machine stops while going uphill, disengage blades, shift into reverse and back down slowly.

Do not turn on slopes unless neces sary, and then, turn slowly and gradu ally downhill, if possible.

Page 6

PRODUCT SPECIFICATIONS

Gasoline Capacity and Type:

Oil Type (API-SG-SL):

Oil Capacity: W/Filter: 3.5 Pints

Spark Plug: (GAP: .030")

Ground Speed (MPH):

Tire Pressure: Front: 14 PSI

Charging System: 3 Amps Battery

Battery: Amp/Hr: 28

Blade Bolt Torque:

CONGRATULATIONS on your purchase of a new tractor. It has been designed, engineered and manufactured to give you the best possible dependability and performance. Should you experience any problem you cannot easily remedy, please contact a Sears or other qualified service center. We have competent, well-trained techni cians and the proper tools to service or repair this tractor. Please read and retain this manual. The instructions will enable you to assemble and maintain your tractor properly. Always observe the “SAFETY RULES”.

1.25 Gallons Unleaded Regular

SAE 30 (above 32T) SAE 5W-30 (Below 32°F)

W/0 Filter: 3.0 Pints

Champion RC12YC

Forward: 5.5 Reverse: 2.4

Rear: 12 PSI

5 Amps Headlights

Min. CCA: 230 Case Size: U1R

27-35 Ft. Lbs.

CUSTOMER RESPONSIBILITIES

• Read and observe the safety rules.

• Follow a regular schedule in main taining, caring for and using your tractor.

• Follow the instructions under “Mainte nance” and “Storage” sections of this owner’s manual.

AwARNING: This tractor is equipped with an internal combustion engine and

should not be used on or near any unim proved forest-covered, brush-covered or grass-covered land unless the engine’s exhaust system is equipped with a spark arrester meeting applicable local or state laws (if any). If a spark arrester is used, it should be maintained in effective working order by the operator.

In the state of California the above is re

quired by law (Section 4442 of the Califor

nia Public Resources Code). Other states may have similar laws. Federal laws apply

on federal lands. A spark arrester for the

muffler is available through your nearest Sears service center (See REPAIR PARTS section of this manual).

REPAIR PROTECTION

AGREEMENTS

Congratulations on making a smart pur

chase. Your new Craftsman® product is

designed and manufactured for years of

dependable operation. But like all prod

ucts, it may require repair from time to

time. That’s when having a Repair Protec

tion Agreement can save you money and

aggravation.

Purchase a Repair Protection Agreement

now and protect yourself from unexpected

hassle and expense.

Here’s what’s included in the Agreement:

• Expert service by our 12,000 profe sional repair specialists.

• Unlimited service and no charge for

parts and labor on all covered repairs.

• Product replacement if your covered

product can’t be fixed.

• Discount of 10% from regular price of service and service-related parts not

covered by the agreement; also, 10%

off regular price of preventive mainte

nance check.

• Fast help by phone - phone support from a Sears technician on products

requiring in-home repair, plus conve

nient repair scheduling. Once you purchase the Agreement, a simple phone call Is all that it takes for you to schedule service. You can call anytime day or night, or schedule a service ap pointment online. Sears has over 12,000 professional repair specialists, who have access to over 4.5 million quality parts and accessories. That’s the kind of professionalism you can count on to help prolong the life of your new purchase for years to come. Purchase your Repair Protection Agreement today!

Some limitations and exclusions apply. For prices and additional information call 1-800-827-6655.

SEARS INSTALLATION SERVICE

For Sears professional installation of home appliances, garage door openers, water heaters, and other major home items, in the U.S.A. call 1-800-4-MY-HOME®

Page 7

UNASSEMBLED PARTS

Gauge

(1) Knob

(1) Oil Drain Tube For Future Use

Keys

Page 8

ASSEMBLY/PRE-OPERATION

Your new tractor has been assembled at the factory with the exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness.

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assembly easier. Standard wrench sizes you need are listed below. (1) 3/4" wrench (1) Pliers (1) 1/2" wrench (1) Utility knife (1) Tire pressure gauge When right or left hand is mentioned in this manual, it means, from your point of view, when you are in the operating posi tion (seated behind the steering wheel).

TO REMOVE TRACTOR FROM

CARTON

UNPACK CARTON

1. Remove all accessible loose parts and parts boxes from carton.

2. Cut along dotted lines on all four pan els of carton. Remove end panels and lay side panels flat.

3. Check for any additional loose parts or cartons and remove.

BEFORE REMOVING TRACTOR FROM SKID

ATTACH STEERING WHEEL

nsert

5/16 Hex Bolt

5/16 Lock Washer

Large Flat

Y Washer

Steering Wheel

Adapter-

Tab Slots

ASSEMBLE EXTENSION SHAFT AND

BOOT

1. Slide extension shaft onto lower steer ing shaft.

2. Place tabs of steering boot over tab slots in dash and push down to secure.

INSTALL STEERING WHEEL

3. Position front wheels of the tractor so they are pointing straight forward.

4. Remove steering wheel adapter from steering wheel and slide adapter onto steering shaft extension.

5. Position steering wheel so cross bars are horizontal (left to right) and slide inside boot and onto adapter.

6. Assemble large flat washer, 5/16 lock washer, 5/16 hex bolt and tighten securely.

7. Snap steering wheel insert into center of steering wheel.

8. Remove protective materials from trac tor hood and grill.

IMPORTANT: Check for and remove any staples in skid that may puncture tires where tractor is to roll off skid.

INSTALL SEAT

Adjust seat before tightening adjustment bolt.

1. Remove adjustment bolt, lock washer and flat washer securing seat to cardboard packing and set aside for assembly of seat to tractor.

2. Pivot seat upward and remove from the cardboard packing. Remove the cardboard packing and discard.

3. Place seat on seat pan so head of shoulder bolts are positioned over the large slotted holes in pan.

4. Push down on seat to engage shoulder bolts in slots and pull seat towards rear of tractor.

5. Pivot seat and pan forward and as semble adjustment bolt, lockwasher and flat washer loosely. Do not tighten.

6. Lower seat into operating position and sit in seat.

Page 9

Slide seat until a comfortable position is reached which allows you to press clutch/brake pedal ail the way down. Get off seat without moving its ad

justed position.

Raise seat and tighten adjustment bolt securely.

CHECK BATTERY

1. Lift seat pan to raised position. NOTE: If this battery is put into service after month and year indicated on label (label located between terminals) charge battery for minimum of one hour at 6-10 amps. (See "BATTERY" in Maintenance section of this manual for charging instruc tions).

/Label

Seat Pan■

Terminal

NOTE: You may now roll or drive your

tractor off the skid. Follow the appropriate

instruction below to remove the tractor

from the skid.

TO ROLL TRACTOR OFF SKID (See

Operation section for location and

function of controls)

1. Press lift lever plunger and raise attachment lift lever to its highest po sition.

Release parking brake by depressing clutch/brake pedal.

Place freewheel control in “trans mission disengaged” position (See “TO TRANSPORT” in the Operation section of this manual).

Roll tractor forward off skid.

Remove banding holding deflector shield up against tractor.

TO DRIVE TRACTOR OFF SKID (See

Operation section for location and

function of controls)

AwARNING: Before starting, read, un derstand and follow all instructions in the

Operation section of this manual. Be sure tractor is in a well-ventilated area. Be sure the area in front of tractor is clear of other

people and objects.

1. Be sure all the above assembly steps have been completed. Check engine oil level and fill fuel tank

2. with gasoline. Place freewheel control in "trans

3. mission engaged" position. (See “TO TRANSPORT” in the Operation section of this manual). Sit on seat in operating position, depress clutch/brake pedal and set the parking brake. Place motion control lever in neutral

5. (N) position. Press lift lever plunger and raise

6. attachment lift lever to its highest posi tion. Start the engine. After engine has

7. started, move throttle control to idle position. Release parking brake.

Slowly move the motion control lever

9. forward and slowly drive tractor off skid.

10. Apply brake to stop tractor, set parking brake and place motion control lever in neutral position.

11 .Turn ignition key to "STOP" position. Continue with the instructions that follow.

Page 10

CHECK TIRE PRESSURE

The tires on your tractor were overinflated at the factory for shipping purposes. Cor rect tire pressure is important for best cutting performance.

• Reduce tire pressure to PSI shown in “PRODUCT SPECiFiCATIONS” section of this manual.

CHECK DECK LEVELNESS

For best cutting results, mower hous ing should be properly leveled. See “TO LEVEL MOWER HOUSING" in the Service and Adjustments section of this manual.

CHECK FOR PROPER POSITION OF ALL BELTS

See the figures that are shown for replac ing motion and mower blade drive belts in the Service and Adjustments section of this manual. Verify that the belts are routed correctly.

CHECK BRAKE SYSTEM

After you learn how to operate your trac

tor, check to see that the brake is properly adjusted. See “TO ADJUST BRAKE” in the Service and Adjustments section of this manual.

i/CHECKLIST

Before you operate your new tractor, we wish to assure that you receive the best performance and satisfaction from this quality product.

Please review the following checklist: y All assembly instructions have been

completed. / No remaining loose parts in carton. y Battery is properly prepared and

charged. (Minimum 1 hour at 6 amps). y Seat is adjusted comfortably and tight

ened securely. / All tires are properly inflated. (For ship

ping purposes, the tires were overin

flated at the factory).

/ Be sure mower deck is properly leveled

side-to-side/front-to-rear for best cutting

results. (Tires must be properly inflated

for leveling).

y Check mower and drive belts. Be sure

they are routed properly around pulleys

and inside all belt keepers. y Check wiring. See that all connections

are still secure and wires are properly

clamped. / Before driving tractor, be sure freewheel

control is in “transmission engaged”

position (see “TO TRANSPORT” in the

Operation section of this manual). While learning how to use your tractor, pay extra attention to the following important

items; y Engine oil is at proper level. / Fuel tank is filled with fresh, clean, reg

ular unleaded gasoline.

y Become familiar with all controls - their

location and function. Operate them before you start the engine.

y Be sure brake system is in safe oper

ating condition.

y Be sure Operator Presence System

and Reverse Operation System (ROS) are working properly (See the Opera tion and Maintenance sections in this

manual).

/ It is important to purge the transmission

before operating your tractor for the first time. Follow proper starting and trans

mission purging instructions (See “TO

START ENGINE” and “PURGE TRANS

MISSION” in the Operation section of this manual).

Page 11

OPERATION

These symbols may appear on your tractor or in literature supplied with the product.

Learn and understand their meaning.

R N

REVERSE

ENGINE OFF REVERSE

01 e

OVER TEMP FUEL OIL PRESSURE BATTERY REVERSE FORWARD MOWER HEIGHT MOWER LIFT

LIGHT

ATTACHMENT

CLUTCH DISENGAGED

•M—

FREE WHEEL

(Automatic Models only)

NEUTRAL

OPERATION

SYSTEM (ROS)

ATTACHMENT

CLUTCH ENGAGED

l-l

HIGH

LOW

141 4»

CHOKE

FAST

ВТ

ENGINE ON ENGINE START PARKING BRAKE PARKING BRAKE PARKING BRAKE

LIGHTS ON

DANGER, KEEP HANDS

AND FEET AWAY

DANGER indicates a hazard which, if not avoided, will result in death or serious injury.

WARNING indicates a hazard which, if not avoided, could result in death or serious injury.

CAUTION indicates a hazard which, if not avoided, might result in minor or moderate injury.

KEEP AREA CLEAR SLOPE HAZARDS

(SEE SAFETY RULES SECTION)

SLOW

LOCKED UNLOCKED

IGNITION SWITCH

/íül

Failure to follow instructions could result in serious injury or death. The safety alert symbol

is used to identify safety inform ation about hazards which can

result in death, serious injury and/or property damage.

CAUTION when used without the alert symbol,

indicates a situation that could result in damage

to the tractor and/or engine.

HOT SURFACES indicates a hazard which,

if not avoided, could result in death, serious injury

and/or property damage.

Y FIRE indicates a hazard which, if not avoided,

could result in death, serious injury and/or property damage.

Page 12

KNOW YOUR TRACTOR

READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR

TRACTOR

Compare the illustrations with your tractor to familiarize yourself with the locations of

various controls and adjustments. Save this manual for future reference.

Our tractors conform to the safety standards of the

American National Standards Institute.

ATTACHMENT CLUTCH LEVER - Used to engage the mower blades, or other at tachments mounted to your tractor. ATTACHMENT LIFT LEVER - Used to

raise, lower, and adjust the mower deck or

other attachments mounted to your tractor.

CLUTCH/BRAKE PEDAL - Used for declutching and braking the tractor and starting the engine.

FREEWHEEL CONTROL - Disengagages transmission for pushing or slowly towing the tractor with the engine off.

IGNITION SWITCH - Used for starting and stopping the engine.

LIFT LEVER PLUNGER - Used to release

attachment lift lever when changing its

position. LIGHT SWITCH - Turns the headlights on and off. MOTION CONTROL LEVER - Selects the

speed and direction of tractor.

PARKING BRAKE LEVER - Locks clutch/ brake pedal into the brake position.

REVERSE OPERATION SYSTEM (ROS) "ON" POSITION - Allows operation of

mower deck or other powered attachment while in reverse. THROTTLE/CHOKE CONTROL - Used for starting and controlling engine speed.

Page 13

The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your tractor or performing any adjustments or repairs. We recommend standard safety glasses or a wide vision safety

mask worn over spectacles.

HOWTO USE YOUR TRACTOR

TO SET PARKING BRAKE

Your tractor is equipped with an operator

presence sensing switch. When engine is running, any attempt by the operator

to leave the seat without first setting the

parking brake will shut off the engine.

1. Depress clutch/brake pedal all the way down and hold.

2. Pull parking brake lever up and release pressure from clutch/brake pedal.

Pedal should remain in brake position. Make sure parking brake will hold trac

tor secure.

Attachment Clutch Lever

“Engaged” Position

Throttle/Choke Control

“Brake” . Position-^

Clutch/Brake Pedal

“Disengaged”

Position

gnition Key

“Disengaged” Position

Motion Control Lever v

Parking Brake “Engaged” Position

STOPPING

MOWER BLADES -

• To stop mower blades, move attachment

clutch lever to “DISENGAGED” position.

GROUND DRIVE -

• To stop ground drive, depress clutch/

brake pedal all the way down.

• Move motion control lever to neutral (N)

position. IMPORTANT: The motion control lever does not return to neutral (N) position when the clutch/brake pedal is depressed.

ENGINE-

• Move throttle control between half and

full speed (fast) position. NOTE: Failure to move throttle control between half and full speed (fast) posi tion, before stopping, may cause engine to “backfire”.

• Turn ignition key to “STOP” position and

remove key. Always remove key when

leaving tractor to prevent unauthorized

use.

• Never use choke to stop engine. IMPORTANT: Leaving the ignition switch in any position other than "STOP" will

cause the battery to discharge and go dead.

NOTE: Under certain conditions when

tractor is standing idle with the engine run

ning, hot engine exhaust gases may cause

“browning” of grass. To eliminate this pos sibility, always stop engine when stopping tractor on grass areas.

AcAUTION: Always stop tractor com pletely, as described above, before leaving the operator's position.

TO USE THROTTLE CONTROL

Always operate engine at full throttle.

• Operating engine at less than full

throttle reduces the battery charging

rate.

• Full throttle offers the best bagging and

mower performance.

TO MOVE FORWARD AND BACKWARD

The direction and speed of movement is controlled by the motion control lever.

1. Start tractor with motion control lever in neutral (N) position.

2. Release parking brake.

3. Slowly move motion control lever to desired position.

TO ADJUST MOWER CUTTING HEIGHT

The position of the attachment lift lever determines the cutting height.

• Grasp lift lever.

• Press plunger with thumb and move lever to desired position.

The cutting height range is approxi

mately 1-1/2 to 4". The heights are mea sured from the ground to the blade tip with the engine not running. These heights

are approximate and may vary depending

upon soil conditions, height of grass and types of grass being mowed.

• The average lawn should be cut to ap proximately 2-1/2 inches during the cool season and to over 3 inches during hot months. For healthier and better looking lawns, mow often and after moderate growth.

• For best cutting performance, grass over 6 inches in height should be mowed twice. Make the first cut relatively high;

'\ 3 the second to desired height.

Page 14

TO OPERATE MOWER

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine. You must

remain fully and centrally positioned in the seat to prevent the engine from hesitating or cutting off when operating your equip

ment on rough, rolling terrain or hills.

1. Select desired height of cut.

2. Start mower blades by engaging at

tachment clutch control. TO STOP MOWER BLADES disengage attachment clutch control.

AcAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped, or the deflector shield in place.

Attachment Clutch Lever “Engaged”

Position

./ ■//—\ \ Low

“Disengaged

Position

Attachemnt

Lift Lever High Position

Position

Deflector Shield

OPERATING IN REVERSE

Your tractor is equipped with a Reverse Operation System (ROS). Any attempt by the operator to travel in the reverse direc tion with the attachment clutch engaged will shut off the engine unless the ignition key is placed in the ROS "ON" position.

AwARNING: Backing up with the at tachment clutch engaged while mowing is strongly discouraged. Turning the ROS "ON", to allow reverse operation with the attachment clutch engaged, should only be done when the operator decides it is necessary to reposition the machine with the attachment engaged. Do not mow in

reverse unless absolutely necessary.

USING THE REVERSE OPERATION SYSTEM -

1. Move motion control lever to neutral (N) position.

2. With engine running, turn ignition key counterclockwise to ROS "ON" posi tion.

3. Look down and behind before backing up.

4. Slowly move motion control lever to reverse (R) position to start movement.

5. When use of the ROS is no longer needed, turn the ignition key clockwise

to engine "ON" position.

ROS "ON" Position Engine "ON" Position

(Normal Operation)

TO OPERATE ON HILLS

AwARNING: Do not drive up or down

hills with slopes greater than 15° and do not drive across any slope. Use the slope guide at the back of this manual.

• Choose the slowest speed before start

ing up or down hills.

• Avoid stopping or changing speed on

hills.

• If slowing is necessary, move throttle

control lever to slower position.

• If stopping is absolutely necessary, push

clutch/brake pedal quickly to brake posi tion and engage parking brake.

• Move motion control lever to neutral (N)

position. IMPORTANT: The motion control lever does not return to neutral (N) position

when the clutch/brake pedal is depressed.

• To restart movement, slowly release

parking brake and clutch/brake pedal.

• Slowly move motion control lever to

slowest setting.

• Make all turns slowly.

TOTRANSPORT

When pushing or towing your tractor, be sure to disengage transmission by placing freewheel control in freewheeling position. Freewheel control is located at the rear drawbar of tractor.

1. Raise attachment lift to highest position with attachment lift control.

2. Pull freewheel control out and down into the slot and release so it is held in

the disengaged position.

• Do not push or tow tractor at more than

two (2) MPH.

• To re-engage transmission, reverse

above procedure.

Page 15

Transmission Engaged

Transmission Disengaged

NOTE: To protect hood from damage

when transporting your tractor on a truck

or a trailer, be sure hood is closed and secured to tractor. Use an appropriate means of tying hood to tractor (rope, cord, etc.).

TOWING CARTS AND OTHER ATTACH MENTS

Tow only the attachments that are recom mended by and comply with specifications of the manufacturer of your tractor. Use common sense when towing. Too heavy of a load, while on a slope, Is dangerous. Tires can lose traction with the ground and cause you to lose control of your tractor.

BEFORE STARTING THE ENGINE

CHECK ENGINE OIL LEVEL

The engine in your tractor has been shipped, from the factory, already filled

with summer weight oil.

1. Check engine oil with tractor on level ground.

2. Remove oil fill cap/dipstick and wipe clean, reinsert the dipstick and screw cap tight, wait for a few seconds, re move and read oil level. If necessary,

add oil until “FULL’ mark on dipstick is

reached. Do not overfill.

• For cold weather operation you should

change oil for easier starting ((See the oil viscosity chart in the Maintenance section of this manual).

• To change engine oil, see the Mainte nance section in this manual.

ADD GASOLINE

• Fill fuel tank to bottom of tank filler neck. Do not overfill. Use fresh, clean, regular unleaded gasoline with a minimum of 87 octane. (Use of leaded gasoline will in crease carbon and lead oxide deposits and reduce valve life). Do not mix oil with gasoline. Purchase fuel in quanti ties that can be used within 30 days to assure fuel freshness.

^CAUTION: Wipe off any spilled oil or fuel. Do not store, spill or use gasoline

near an open flame.

IMPORTANT: When operating in tempera tures below 32°F(0°C), use fresh, clean winter grade gasoline to help insure good

cold weather starting.

CAUTION: Alcohol blended fuels (called gasohoi or using ethanol or methanol) can

attract moisture which leads to separation and formation of acids during storage. Acid

ic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines

and carburetor are empty. Use fresh fuel

next season. See Storage Instructions for

additional information.

Never use engine or carburetor cleaner

products in the fuel tank or permanent damage may occur.

TO START ENGINE

When starting the engine for the first time or if the engine has run out of fuel, it will take extra cranking time to move fuel from the tank to the engine.

1. Be sure freewheel control is in the transmission engaged position.

2. Sit on seat in operating position, depress clutch/brake pedal and set parking brake.

3. Place motion control lever in neutral (N) position.

4. Move attachment clutch to disengaged position.

5. Move throttle control to choke position. NOTE: Before starting, read the warm and cold starting procedures below.

6. Insert key into ignition and turn key clockwise to start position and release key as soon as engine starts. Do not run starter continuously for more than fifteen seconds per minute, if the engine does not start after several attempts, move throttle control to fast position, wait a few minutes and try again. If engine still does not start, move the throttle control back to the choke position and retry.

WARM WEATHER STARTING (50° F and above)

7. When engine starts, move the throttle control to the fast position.

• The attachments and ground drive can

now be used. If the engine does not accept the load, restart the engine and allow It to warm up for one minute using

the choke as described above.

Page 16

COLD WEATHER STARTING ( 50° F and below)

7. When engine starts, allow engine to run with the throttle control in the choke position until the engine runs

roughly, then move throttle control to fast position. This may require an engine warm-up period from several seconds to several minutes, depending on the temperature.

AUTOMATIC TRANSMISSION WARM UP

Before driving the unit in cold weather, the transmission should be warmed up as follows;

1. Be sure the tractor is on level ground.

2. Place the motion control lever in

neutral. Release the parking brake and let the clutch/brake slowly return to operating position.

3. Allow one minute for transmission to warm up. This can be done during the engine warm up period.

• The attachments can also be used dur

ing the engine warm-up period after the transmission has been warmed up.

NOTE: If at a high altitude (above 3000 feet) or in cold temperatures (below 32 F) the carburetor fuel mixture may need to be adjusted for best engine performance. (See “TO ADJUST CARBURETOR” in the Service and Adjustments section of this

manual.)

PURGE TRANSMISSION

To ensure proper operation and per formance, it is recommended that the transmission be purged before operating tractor for the first time. This procedure will

remove any trapped air inside the trans

mission which may have developed during shipping of your tractor.

IMPORTANT: Should your transmission

require removal for service or replace

ment, it should be purged after reinstall ation before operating the tractor.

1. Place tractor safely in an area that is flat for approximately 80 feet in front of the tractor and set the parking brake.

2. Sitting in the tractor seat, start engine. After the engine is running, move throttle control to slow position. With

motion control lever in neutral (N) position, slowly disengage clutch/brake pedal.

3. Slowly move motion control lever to full forward position and hold for five

(5) seconds, or approximately 40 feet.

Slowly move lever to full reverse posi tion and hold for five (5) seconds, or approximately 20 feet. After the tractor

moves approximately 20 feet in reverse

return the motion control lever to the

neutral (N) position. Repeat this proce dure three (3) times.

Your transmission is now purged and now ready for normal operation.

MOWING TIPS

• Mower should be properly leveled for best mowing performance. See “TO

LEVEL MOWER HOUSING” in the

Service and Adjustments section of this

manual.

• The left hand side of mower should be used for trimming.

• Drive so that clippings are discharged onto the area that has already been cut.

Have the cut area to the right of the trac tor. This will result in a more even distri bution of clippings and more uniform cutting.

• When mowing large areas, start by turning to the right so that clippings will discharge away from shrubs, fences, driveways, etc. After one or two rounds,

mow in the opposite direction making left hand turns until finished.

• If grass is extremely tall, it should be

mowed twice to reduce load and pos

sible fire hazard from dried clippings.

Make first cut relatively high; the second

to the desired height.

• Do not mow grass when it is wet. Wet grass will plug mower and leave undesirable clumps. Allow grass to dry before mowing.

• Always operate engine at full throttle when mowing to assure better mowing

performance and proper discharge of

material. Regulate ground speed by

selecting a low enough gear to give the

mower cutting performance as well as

the quality of cut desired.

• When operating attachments, select a ground speed that will suit the terrain and give best performance of the at-

-|g tachment being used.

Page 17

MAINTENANCE

MAINTENANCE SCHEDULE

FILL IN DATES AS YOU COMPLETE REGULAR SERVICE

Check Brake Operation Check Tire Pressure

Check Operator Presence and ROS Systems

Check for Loose Fasteners

Sharpen/Replace Mower Blades Lubrication Chart Check Battery Level Clean Battery and Terminals Check Transaxle Cooling Check V-Belts

Check Engine Oil Level Change Engine Oil (with oil filter)

Change Engine Oil (without oil filter)

Clean Air Filter Clean Air Screen Inspect Muffler/Spark Arrester Replace Oil Filter (If equipped) Clean Engine Cooling Fins Replace Spark Plug Replace Air Filter Paper Cartridge Replace Fuel Filter

1 - Change more often when operating under a heavy load or

in high ambient temperatures.

2 - Service more often when operating in dirty or dusty conditions.

GENERAL RECOMMENDATIONS

The warranty on this tractor does not cover items that have been subjected to operator abuse or negligence. To receive full value from the warranty, operator must maintain tractor as instructed in this manual. Some adjustments will need to be made periodically to properly maintain your tractor.

At least once a season, check to see if

you should make any of the adjustments described in the Service and Adjustments section of this manual.

• At least once a year you should replace the spark plug, clean or replace air filter, and check blades and belts for wear. A new spark plug and clean air filter assure proper air-fuel mixture and help your engine run better and last longer.

BEFORE EACH USE

1. Check engine oil level.

2. Check brake operation.

3. Check tire pressure.

4. Check operator presence and ROS systems for proper operation.

5. Check for loose fasteners.

✓ ✓

✓

SERVICE DATES

✓

✓ ✓ a ✓ ✓

✓ 4

✓ ✓ ✓

✓

1,2 ✓

✓ 1,2

✓ 2

✓

1^,2 ✓ 2 ✓ ✓

✓ 2

3 - Replace blades more often when mowing in sandy soil. 4 - Not required if equipped with maintenance-free battery. 5 - Tighten front axle pivot bolt to 35 ft.-lbs. maximum.

Do not overtighten.

✓

±1

LUBRICATION CHART

(D Spindle Zerk

©Front Wheel _c

Bearing Zerk

©Engine

® General Purpose Grease © REFER TO Maintenance “ENGINE” SECTION

IMPORTANT: Do not oil or grease the pivot points which have special nylon bearings. Viscous lubricants will attract dust and dirt that will shorten the life of the self-lubricating bearings. If you feel they

must be lubricated, use only a dry, pow dered graphite type lubricant sparingly.

® Spindle Zerk

©Front Wheel

Bearing Zerk

Page 18

TRACTOR

Always observe safety rules when per

forming any maintenance. BRAKE OPERATION

If tractor requires more than five (5) feet to stop at highest speed in highest gear on a ievel, dry concrete or paved surface, then brake must be checked and adjusted. (See “TO ADJUST BRAKE” in the Service and

Adjustments section of this manual).

TIRES

• Maintain proper air pressure in ali tires (See “PRODUCT SPECIFICATIONS" section of this manual).

• Keep tires free of gasoline, oil, or insect control chemicals which can harm rub ber.

• Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

OPERATOR PRESENCE SYSTEM AND REVERSE OPERATION SYSTEM (ROS)

Be sure operator presence and reverse operation systems are working properly. If your tractor does not function as de scribed, repair the problem immediately.

• The engine should not start unless the brake pedal is fully depressed, and the attachment clutch control is in the disen gaged position.

CHECK OPERATOR PRESENCE SYSTEM

• When the engine is running, any at tempt by the operator to leave the seat without first setting the parking brake should shut off the engine.

• When the engine is running and the attachment clutch is engaged, any at tempt by the operator to leave the seat should shut off the engine.

• The attachment clutch should never op erate unless the operator is in the seat.

CHECK REVERSE OPERATION (ROS) SYSTEM

• When the engine is running with the ig nition switch in the engine "ON" position and the attachment clutch is engaged, any attempt by the operator to shift into reverse should shut off the engine.

ROS "ON" Position Engine "ON" Position

(Normal Operation)

• When the engine is running with the ignition switch in the ROS "ON" position

and the attachment clutch is engaged, any attempt by the operator to shift into

reverse should NOT shut off the engine

BLADE CARE

For best results mower blades must be kept

sharp. Replace bent or damaged blades.

BLADE REMOVAL

1. Raise mower to highest position to al low access to blades.

2. Remove blade bolt, lock washer and

flat washer securing blade.

3. Install new or resharpened blade

with trailing edge up towards deck as

shown. IMPORTANT: To ensure proper assembly, center hole in blade must align with star on mandrel assembly.

4. Reassemble blade bolt, lock washer

and flat washer in exact order as

shown.

5. Tighten blade bolt securely (27-35 Ft.

Lbs. torque). IMPORTANT: Blade bolt is heat treated. If bolt needs replacing, replace only with approve bolt shown in the Repair Parts,

y^gjljpig Mandrel Assembly Edge Up-

Flat Washer

Lock Washer

'Blade Bolt

Star

TO SHARPEN BLADE NOTE: We do not recommend sharp

ening blade - but if you do, be sure the blade is balanced. Care should be taken to keep the blade balanced. An unbalanced blade will cause excessive vibration and eventual damage to mower and engine.

• The blade can be sharpened with a file

or on a grinding wheel. Do not attempt to sharpen while on the mower.

• To check blade balance, you will need a

5/8" diameter steel bolt, pin, or a cone balancer. (When using a cone balancer,

follow the instructions supplied with

-|0 balancer.)

Page 19

NOTE: Do not use a nail for balancing blade. The lobes of the center hole may appear to be centered, but are not.

• Slide blade on to an unthreaded portion of the steel bolt or pin and hold the bolt or pin parallel with the ground. If blade is balanced, it should remain in a horizontal position. If either end of the blade moves downward, sharpen the heavy end until the blade is balanced.

• Inspect cooling fins for dirt, grass clip pings and other materials. To prevent damage to seals, do not use com pressed air or high pressure sprayer to clean cooling fins.

TRANSAXLE PUMP FLUID The transaxle was sealed at the factory

and fluid maintenance is not required for

the life of the transaxle. Should the trans

axle ever leak or require servicing, contact a Sears or other qualified service center.

V-BELTS

Check V-belts for deterioration and wear after

100 hours of operation and replace if neces

sary. The belts are not adjustable. Replace

belts if they begin to slip from wear.

BATTERY

Your tractor has a battery charging system which is sufficient for normal use. How ever, periodic charging of the battery with an automotive charger will extend its life.

• Keep battery and terminals clean.

• Keep battery bolts tight.

• Keep small vent holes open.

• Recharge at 6-10 amperes for 1 hour.

NOTE: The original equipment battery on your tractor is maintenance free. Do not attempt to open or remove caps or covers. Adding or checking level of electrolyte is

not necessary. TO CLEAN BATTERY AND TERMINALS Corrosion and dirt on the battery and terminals can cause the battery to “leak”

power.

1. Disconnect BLACK battery cable first then RED battery cable and remove battery from tractor.

2. Rinse the battery with plain water and dry.

3. Clean terminals and battery cable ends with wire brush until bright.

4. Coat terminals with grease or petro leum jelly.

5. Reinstall battery (See “REPLACING BATTERY" in the Service and Adjust ments section of this manual).

TRANSAXLE COOLING

The transmission fan and cooling fins should be kept clean to assure proper cooling. Do not attempt to clean fan or transmis sion while engine is running or while the transmission is hot. To prevent possible damage to seals, do not use high pressure

water or steam to clean transaxle.

• Inspect cooling fan to be sure fan blades are intact and clean.

ENGINE

LUBRICATION

Only use high quality detergent oil rated with API service classification SG-SL. Se lect the oil’s SAE viscosity grade according to your expected operating temperature.

SAE VISCOSITY GRADES

TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE

NOTE: Although multi-viscosity oils (5W30, 10W30 etc.) improve starting in cold weather, they will result in increased

oil consumption when used above 32°F.

Check your engine oil level more frequent ly to avoid possible engine damage from running low on oil. Change the oil after every 50 hours of op eration or at least once a year if the tractor is not used for 50 hours in one year. Check the crankcase oil level before start ing the engine and after each eight (8)

hours of operation. Tighten oil fill cap/ dipstick securely each time you check the oil level.

TO CHANGE ENGINE OIL Determine temperature range expected

before oil change. All oil must meet API service classification SG-SL.

• Be sure tractor is on level surface.

• Oil will drain more freely when warm.

• Catch oil in a suitable container.

1. Remove oil fill cap/dipstick. Be careful not to allow dirt to enter the engine

when changing oil.

2. Remove yellow cap from end of drain valve and install the drain tube onto the

fitting.

Page 20

Oil Drain Valve

3. Unlock drain valve by pushing inward slightly and turning counterclockwise.

4. To open, pull out on the drain valve.

5. After oil has drained completely, close and lock the drain valve by pushing inward and turning clockwise until the pin is in the locked position as shown.

6. Remove the drain tube and replace the

cap onto the end of the drain valve.

7. Refill engine with oil through oil fill dip stick tube. Pour slowly. Do not overfill. For approximate capacity see “PROD UCT SPECIFICATIONS” section of this manual.

8. Use gauge on oil fill cap/dipstick for

checking level. For accurate reading, tighten dipstick cap securely onto the tube before removing dipstick. Keep oil at “FULL’ line on dipstick. Tighten cap onto the tube securely when finished.

ENGINE OIL FILTER

Replace the engine oil filter every season

or every other oil change if the tractor is used more than 100 hours in one year.

AIR FILTER

Your engine will not run properly using a dirty air filter. Replace pre-cleaner after every 25 hours of operation or every season. Service paper cartridge every

100 hours of operation or every season,

whichever occurs first. Service air cleaner more often under dusty conditions.

1. Pull up on air filter cover handle and rotate towards engine.

2. Remove cover.

3. Carefully remove air filter cartridge and pre-cleaner from base.

4. Clean base carefully to prevent debris from falling into carburetor.

NOTE: If very dirty or damaged, replace

cartridge.

5. Place new pre-cleaner and cartridge firmly in base.

6. Align tabs on cover with slots in blower

housing and replace cover.

7. Hook handle on cover and push down on handle to close.

IMPORTANT: Petroleum solvents, such as kerosene, are not to be used to clean

the cartridge. They may cause deterio

ration of the cartridge. Do not oil car

tridge. Do not use pressurized air to clean

cartridge.

CLEAN AIR SCREEN

Air screen must be kept free of dirt and chaff to prevent engine damage from overheating. Clean with a wire brush or compressed air to remove dirt and stub born dried gum fibers.

ENGINE COOLING SYSTEM

Debris may clog the engine’s air cool

ing system. Remove blower housing and clean area shown to prevent overheating and engine damage.

Page 21

MUFFLER

Inspect and replace corroded muffler and spark arrester (if equipped) as it could cre ate a fire hazard and/or damage.

SPARK PLUG(S)

Replace spark plug(s) at the beginning of each mowing season or after every

100 hours of operation, whichever occurs

first. Spark plug type and gap setting are shown in “PRODUCT SPECIFICATIONS” section of this manual.

IN-LINE FUEL FILTER

The fuel filter should be replaced once each season. If fuel filter becomes

clogged, obstructing fuel flow to carbu retor, replacement is required.

1. With engine cool, remove filter and

plug fuel line sections.

2. Place new fuel filter in position in fuel line with arrow pointing towards carbu retor.

3. Be sure there are no fuel line leaks and clamps are properly positioned.

4. Immediately wipe up any spilled gaso line.

CLEANING

• Clean engine, battery, seat, finish, etc. of all foreign matter.

• Keep finished surfaces and wheels free of all gasoline, oil, etc.

• Protect painted surfaces with automotive type wax.

We do not recommend using a garden

hose or pressure washer to clean your tractor unless the engine and transmis sion covered to keep water out. Water

in engine or transmission will shorten the

usful life of your tractor. Use compressed air or a leaf blower to remove grass, leaves and trash from tractor and mower.

Clamp

Fuel Filter

Clamp

Page 22

SERVICE AND ADJUSTMENTS

WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY

SERVICE OR ADJUSTMENTS:

1. Depress clutch/brake pedal fully and set parking brake.

2. Place motion control lever in neutral (N) position.

3. Place attachment clutch in “DISENGAGED” position.

4. Turn ignition key to “STOP” and remove key.

5. Make sure the blades and ail moving parts have completely stopped.

6. Disconnect spark plug wire from spark plug and place wire where it cannot

come in contact with plug.

TRACTOR

TO REMOVE MOWER

Mower will be easier to remove from the right side of tractor.

Place attachment clutch in “DISEN GAGED” position.

Move attachment lift lever forward to lower mower to its lowest position.

Roll belt off engine pulley.

Remove small retainer spring, and remove clutch spring off pulley bolt.

Remove large retainer spring, slide collar off and push housing guide out of bracket.

Disconnect anti-sway bar from chassis bracket by removing retainer spring. Disconnect suspension arms from rear deck brackets by removing retainer springs. Disconnect front links from deck by removing retainer springs.

Raise lift lever to raise suspension arms. Slide mower out from under trac tor.

Small Retainer Spring

Clutch Spring

IMPORTANT: If an attachment other than the mower deck is to be mounted on the tractor, remove the front links and hook the clutch spring Into square hole in frame.

TO INSTALL MOWER

Raise attachment lift lever to its highest

position.

Slide mower under tractor with deflec tor shield to right side of tractor.

Lower lift lever to its lowest position.

Connect front links to mower deck and secure with retainer springs.

Connect suspension arms to rear deck brackets and secure with retainer springs.

Connect anti-sway bar to chassis bracket and secure with retainer spring.

Push clutch cable housing guide into bracket, slide collar onto guide and secure with large retainer spring.

Square Hole

Retainer Spring

Anti-Sway Bar

Collar

Housing

Guide

Engine Pulley

Retainer Springs (Both Sides)

Deflector Shield

Large Retainer Spring

Page 23

8. Place flat washer and clutch spring on

idler pulley bolt and secure with small retainer spring.

9. Install belt onto engine pulley.

TO LEVEL MOWER HOUSING

Adjust the mower while tractor is parked

on level ground or driveway. Make sure tires are properly inflated (See “PROD

UCT SPECIFICATIONS” section of this manual). If tires are over or underinflated,

you will not properly adjust your mower. SIDE-TO-SIDE ADJUSTMENT

• Raise mower to its highest position.

• At the midpoint of both sides of mower, measure height from bottom edge of mower to ground. Distance “A” on both

sides of mower should be the same or within 1/4" of each other.

• If adjustment is necessary, make adjust ment on one side of mower only.

• To raise one side of mower, tighten lift link adjustment nut on that side.

• To lower one side of mower, loosen lift link adjustment nut on that side.

NOTE: Each full turn of adjustment nut

will change mower height about 1/8".

• Recheck measurements after adjusting.

Bottom edge of mower to ground

Bottom edge of

mower to ground

If links are not equal in length, adjust one link to same length as other link. To lower front of mower loosen nut “E” on both front links an equal number of turns. When distance “D” is 1/8" to 1/2"

lower at front than rear, tighten nuts “F” against trunnion on both front links. To raise front of mower, loosen nut “F" from trunnion on both front links. Tighten

nut “E” on both front links an equal num ber of turns. The two front links must

remain equal in length. When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nut “F” against trunnion on both front links.

Recheck side-to-side adjustment.

Suspension Arm

Lift Link

Adjustment Nut

FRCNT-TC-BACK ADJUSTMENT IMPORTANT: Deck must be level side-to

side. If the following front-to-back adjust

ment is necessary, be sure to adjust both front links equally so mower will stay level side-to-side. To obtain the best cutting results, the

mower housing should be adjusted so that the front is approximately 1/8" to 1/2"

lower than the rear when the mower is in

its highest position. Check adjustment on right side of trac tor. Measure distance “D” directly in front and behind the mandrel at bottom edge of

mower housing as shown.

• Before making any necessary adjust

ments, check that both front links are

equal in length.

TO REPLACE MOWER BLADE DRIVE BELT

The mower blade drive belt may be re placed without tools. Park the tractor on level surface. Engage parking brake.

BELT REMOVAL -

1. Remove mower from tractor (See “TO REMOVE MOWER” in this section of manual).

2. Work belt off both mandrel pulleys and idler pulleys.

3. Pull belt away from mower.

BELT INSTALLATION -

1. Work belt around both mandrel pulleys and idler pulleys

2. Make sure belt is in all pulley grooves

23 and inside all belt guides.

Page 24

3. Install mower (See “To Install Mower” in this section of this manual).

Mandrel

Your tractor is equipped with an adjustable brake system which is mounted on the right side of the transaxle.

If tractor requires more than five (5) feet to stop at highest speed in highest gear on a ievel, dry concrete or paved surface, then brake must be checked and adjusted.

TO CHECK BRAKE

1. Park tractor on a level, dry concrete or paved surface, depress clutch/brake pedal all the way down and engage parking brake.

2. Disengage transmission by placing freewheel control in “transmission dis

engaged” position. Puli freewheel con trol out and into the slot and release so

it is held in the disengaged position. The rear wheeis must lock and skid when you try to manuaiiy push the tractor for

ward. If the rear wheels rotate, the brake

needs to be adjusted or the pads need to be replaced.

TC ADJUST BRAKE

1. Depress clutch/brake pedal all the way down and engage parking brake.

2. Measure distance between brake oper ating arm and nut “A" on brake rod.

3. If distance is other than 1-9/16", loosen

jam nut and turn nut “A” until distance

becomes 1-9/16". Retighten jam nut against nut “A”.

4. Engage transmission by placing freewheel control in “transmission engaged” position.

5. Road test tractor for proper stopping distance as stated above. Readjust

if necessary. If stopping distance is still greater than five (5) feet in highest gear, further maintenance is neces sary. Replace brake pads or contact a Sears or other qualified service center.

With parking brake “Engaged”

TO REPLACE MOTION DRIVE BELT

Park the tractor on level surface. Engage parking brake. For assistance, there is a belt installation guide decal on bottom side

of left footrest.

BELT REMOVAL -

1. Remove mower (See “TO REMOVE MOWER” in this section of manual).

NOTE: Observe entire motion drive belt and position of all belt guides and keepers.

2. Remove belt from stationary idler and clutching idler.

3. Remove belt downward from around engine pulley.

4. Pull belt slack toward rear of tractor. Carefully remove belt upwards from transmission input pulley.

5. Remove belt from center span keeper and pull belt away from tractor.

BELT INSTALLATION -

Carefully work new belt down onto the input pulley.

Slide belt into the center span keeper.

Pull belt toward front of tractor and roll around the top groove of engine pulley.

Install belt through stationary idler and clutching idler. Make sure belt is in all pulley grooves and inside all belt guides and keepers.

Install mower (See “TO INSTALL MOWER” in this section of manual).

Page 25

TRANSAXLE MOTION CONTROL LE VER NEUTRAL ADJUSTMENT

The motion control lever has been preset

at the factory and adjustment should not be necessary.

1. Loosen adjustment bolt in front of the right rear wheel, and lightly tighten.

2. Start engine and move motion control lever until tractor does not move for

ward or backward.

3. Hold motion control lever in that posi tion and turn engine off.

4. While holding motion control lever in place, loosen the adjustment bolt.

5. Move motion control lever to the neu tral (N) (lock gate) position.

6. Tighten adjustment bolt securely.

NOTE: If additional clearance is needed to get to adjustment bolt, move mower deck height to the lowest position. After above adjustment is made, if the tractor still creeps forward or backward while motion control lever is in neutral

position, follow these steps;

Loosen the adjustment bolt.

Move the motion control lever 1/4 to

1/2 inch in the direction it is trying to

creep.

Tighten adjustment bolt securely.

Start engine and test.

If tractor still creeps, repeat above

steps until satisfied.

TRANSMISSION REMOVAL/

REPLACEMENT

Should your transmission require removal for

service or replacement, it should be purged

after reinstallation and before operating the tractor. See “PURGE TRANSMISSION” in the Operation section of this manual.

TO ADJUST STEERING WHEEL ALIGN

MENT

If steering wheel crossbars are not

horizontal (left to right) when wheels are

positioned straight forward, remove steer

ing wheel and reassemble with crossbars

horizontal. Tighten securely.

FRONT WHEEL TOE-IN/CAMBER The front wheel toe-in and camber are not

adjustable on your tractor, if damage has occurred to affect the front wheel toe-in or

camber, contact a Sears or other qualified service center.

TO REMOVE WHEEL FOR REPAIRS

1. Block up axle securely.

2. Remove axle cover, retaining ring and

washers to allow wheel removal (rear wheels have a square key - Do not lose).

3. Repair tire and reassemble.

NOTE: On rear wheels only: align grooves in

rear wheel hub and axle. Insert square key.

4. Replace washers and snap retaining

ring securely in axle groove.

5. Replace axle cover.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, purchase and

use tire sealant from Sears. Tire sealant

also prevents tire dry rot and corrosion.

Washers

Retaining Ring

Axle Cover

Square Key

(Rear Wheel Only)

TO START ENGINE WITH A WEAK BAT TERY

A WARNING: Lead-acid batteries gen

erate explosive gases. Keep sparks, flame

and smoking materials away from bat teries. Always wear eye protection when

around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BAT TERY" in the MAINTENANCE section of this manual).

Page 26

If “jumper cables” are used for emergency

starting, follow this procedure:

IMPORTANT: Your tractor is equipped

with a 12 volt system. The other vehicle

must also be a 12 volt system. Do not use

your tractor battery to start other vehicles.

Seat Pan

TO ATTACH JUMPER CABLES -

1. Connect one end of the RED cable to the POSITIVE (+) terminal of each battery(A-B), taking care not to short against tractor chassis. Connect one end of the BLACK cable

2. to the NEGATIVE (-) terminal (C) of fully charged battery. Connect the other end of the BLACK

3. cable (D) to good chassis ground, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER-

1. BLACK cable first from chassis and then from the fully charged battery.

2. RED cable last from both batteries.

Weak or Dead Battery Fully Charged Battery

REPLACING BATTERY

AwARNING: Do not short battery terminals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery,

remove metal bracelets, wristwatch bands, rings, etc.

Positive terminal must be connected first to prevent sparking from accidental grounding.

1. Lift seat pan to raised position.

2. Disconnect BLACK battery cable first

then RED battery cable and carefully remove battery from tractor.

3. Install new battery with terminals in

same position as old battery.

4. First connect RED battery cable to

positive (+) terminal with hex bolt and keps nut as shown. Tighten securely. Slide terminal cover over terminal

5. Connect BLACK grounding cable to

negative (-) terminal with remaining hex bolt and keps nut. Tighten securely.

/1- M

Termina Cover

Keps Nut

Hex Bolt

Positive (Red) Cable Negative (Black) Cable

TO REPLACE HEADLIGHT BULB

1. Raise hood.

2. Pull bulb holder out of the hole in the backside of the grill.

3. Replace bulb in holder and push bulb holder securely back into the hole in

the backside of the grill.

4. Close hood. INTERLOCKS AND RELAYS

Loose or damaged wiring may cause your tractor to run poorly, stop running, or prevent it from starting.

• Check wiring. See electrical wiring

diagram in the Repair Parts section.

TO REPLACE FUSE Replace with 20 amp automotive-type

plug-in fuse. The fuse holder is located behind the dash.

TO REMOVE HOOD AND GRILL AS SEMBLY

1. Raise hood.

2. Unsnap headlight wire connector.

3. Stand in front of tractor. Grasp hood at

sides, tilt toward engine and lift off of tractor.

4. When replacing hood, be sure to re

connect the headlight wire connector.

Page 27

ENGINE

Maintenance, repair, or replacement of the emission control devices and systems, which are being done at the customers expense,

may be performed by any non-road engine

repair estabiishment or individual. Warranty

repairs must be performed by an authorized engine manufacturer's service outlet.

TO ADJUST THROTTLE CONTROL CABLE

The throttle control has been preset at the factory and adjustment should not be nec essary. Check adjustment as described below before loosening cable. If adjust

ment is necessary, proceed as follows:

1. With engine not running, move throttle control lever from slow to choke posi

tion. Slowly move lever from choke to fast position.

2. Check that holes “A” in governor control lever and hole in governor plate line-up. If holes “A” are not aligned, loosen clamp screw and move throttle cable until holes are aligned. Tighten clamp screw securely.

IMPORTANT: Damage to the needle

valve and the seat in carburetor may result

if screw is turned in too tight. PRELIMINARY SETTING-

1. Air cleaner assembly must be assem bled to the carburetor when making carburetor adjustments.

2. Be sure the throttle control cable is adjusted properly (see above).

FINAL SETTING -(See “TO ADJUST THROTTLE CONTROL CABLE” in this section of the manual.)

1. Start engine and allow to warm for five minutes. Make final adjustments with

engine running and shift/motion control

lever in neutral (N) position.

2. Move throttle control lever to slow posi tion. With finger, rotate and hold throttle

lever against idle speed screw. Turn idle speed screw to attain 1750 RPM.

3. While still holding throttle lever against idle speed screw, turn idle mixture

valve full travel clockwise then counter

clockwise until engine runs rough. Turn

valve to a point midway between those two positions. Release throttle lever.

TO ADJUST CARBURETOR

NOTE: The carburetor on this engine is

low emission, it is equipped with an idle fuel adjusting needle with a limiter cap, which allows some adjustment within the

limits allowed by the cap. Do not attempt to remove the limiter cap. The limiter cap cannot be removed without breaking the adjusting needle. The carburetor has been preset at the factory and adjustment should not be

necessary. However, minor adjustment

may be required to compensate for differ ences in fuel, temperature, altitude or load.

If the carburetor does need adjustment, proceed as follows:

In general, turning idle mixture valve in (clockwise) decreases the supply of fuel to the engine giving a leaner fuel/air mix ture. Turning the idle mixture valve out (counterclockwise) increases the supply of fuel to the engine giving a richer fuel/air

mixture.

ACCELERATION TEST -

4. Move throttle control lever from slow to fast position. If engine hesitates or dies, turn idle mixture valve out (coun terclockwise) 1/8 turn. Repeat test and

continue to adjust, if necessary, until

engine accelerates smoothly.

High speed stop is factory adjusted. Do not adjust or damage may result.

IMPORTANT: Never tamper with the engine governor, which is factory set for proper engine speed. Overspeeding the engine above the factory high speed setting can be dangerous. If you think the engine-governed high speed needs adjust

ing, contact a Sears or other qualified ser vice center, which has proper equipment

and experience to make any necessary

adjustments.

Page 28

STORAGE

Immediately prepare your tractor for stor age at the end of the season or if the trac tor will not be used for 30 days or more.

AcAUTION: Never store the tractor with gasoline in the tank inside a building where fumes may reach an open flame

or spark. Allow the engine to cool before storing in any enclosure.

TRACTOR

Remove mower from tractor for winter storage. When mower is to be stored for a period of time, clean it thoroughly, remove all dirt, grease, leaves, etc. Store in a clean, dry area.

1. Clean entire tractor (See “CLEANING” in the Maintenance section of this manual).

2. Inspect and replace belts, if necessary (See belt replacement instructions in the Service and Adjustments section of this manual).

3. Lubricate as shown in the Maintenance section of this manual.

4. Be sure that all nuts, bolts and screws are securely fastened. Inspect moving parts for damage, breakage and wear. Replace if necessary.

5. Touch up all rusted or chipped paint surfaces; sand lightly before painting.

BATTERY

• Fully charge the battery for storage.

• After a period of time in storage, battery

may require recharging.

• To help prevent corrosion and power

leakage during long periods of storage, battery cables should be disconnected and battery cleaned thoroughly (see “TO CLEAN BATTERY AND TERMINALS” in the Maintenance section of this manual).

• After cleaning, leave cables discon

nected and place cables where they cannot come in contact with battery terminals.

• If battery is removed from tractor for

storage, do not store battery directly on concrete or damp surfaces.

ENGINE

FUEL SYSTEM IMPORTANT: It is important to prevent

gum deposits from forming in essential fuel system parts such as carburetor, fuel

hose, or tank during storage. Also, alcohol

blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can dam

age the fuel system of an engine while in storage.

• Empty the fuel tank by starting the en gine and letting it run until the fuel lines and carburetor are empty.

• Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

• Use fresh fuel next season.

NOTE: Fuel stabilizer is an acceptable

alternative in minimizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or stor

age container. Always follow the mix ratio found on stabilizer container. Run engine at least 10 minutes after adding stabilizer to allow the stabilizer to reach the car

buretor. Do not empty the gas tank and

carburetor if using fuel stabilizer.

ENGINE OIL

Drain oil (with engine warm) and replace with clean engine oil. (See “ENGINE” in the Maintenance section of this manual).

CYLINDER(S)

1. Remove spark plug(s).

2. Pour one ounce of oil through spark

plug hole(s) into cylinder(s).

3. Turn ignition key to “START” position for a few seconds to distribute oil.

4. Replace with new spark p!ug(s).

OTHER

• Do not store gasoline from one season

to another.

• Replace your gasoline can if your can

starts to rust. Rust and/or dirt in your gasoline will cause problems.

• If possible, store your tractor indoors

and cover it to give protection from dust and dirt.

• Cover your tractor with a suitable pro

tective cover that does not retain mois ture. Do not use plastic. Plastic cannot breathe which allows condensation to form and will cause your tractor to rust.

IMPORTANT: Never cover tractor while

engine and exhaust areas are still warm.

Page 29

TROUBLESHOOTING CHART: See appropriate section in manual unless directed to Sears service center

PROBLEM CAUSE CORRECTION

Will not start 1. Out of fuel.

2. Engine not “CHOKED” properly.

3. Engine flooded.

4. Bad spark plug.

5. Dirty air filter.

6. Dirty fuel filter.

7. Water in fuel.

8. Loose or damaged wiring.

9. Carburetor out of adjustment.

10. Engine valves out of adjustment.

Hard to start 1. Dirty air filter.

2. Bad spark plug.

3. Weak or dead battery.

4. Dirty fuel filter.

5. Stale or dirty fuel.

6. Loose or damaged wiring.

7. Carburetor out of adjustment.

8. Engine valves out of

adjustment.

1. Fill fuel tank.

2. See “TO START ENGINE” in Operation section.

3. Wait several minutes before attempting to start.

4. Replace spark plug.

5. Clean/replace air filter.

6. Replace fuel filter.

7. Empty fuel tank and carbure tor, refill tank with fresh gas oline and replace fuel filter.

8. Check all wiring.

9. See “To Adjust Carburetor” in Service and Adjustments section.

10. Contact a Sears or other qualified service center.

1. Clean/replace air filter.

2. Replace spark plug.

3. Recharge or replace battery.

4. Replace fuel filter.

5. Empty fuel tank and refill tank with fresh, clean gasoline.

6. Check all wiring.

7. See “To Adjust Carburetor” in

Service and Adjustments

section.

8. Contact a Sears or other

qualified service center.

Engine will not

turn over

1. Brake pedal not depressed.

2. Attachment clutch is engaged.

3. Weak or dead battery.

4. Blown fuse.

5. Corroded battery terminals.

6. Loose or damaged wiring.

7. Faulty ignition switch.

8. Faulty solenoid or starter.

9. Faulty operator presence switch(es).

Engine clicks but

will not start

Loss of power 1. Cutting too much grass/too

1. Weak or dead battery.

2. Corroded battery terminals.

3. Loose or damaged wiring.

4. Faulty solenoid or starter.

fast.

2. Throttle in “CHCKE” position.

3. Build-up of grass, leaves and trash under mower.

4. Dirty air filter.

5. Lowoil level/dirty oil.

1. Depress brake pedal.

2. Disengage attachment clutch.

3. Recharge or replace battery.

4. Replace fuse.

5. Clean battery terminals.

6. Check all wiring.

7. Check/replace ignition switch.

8. Check/replace solenoid or

starter.

9. Contact a Sears or other qualified service center.

1. Recharge or replace battery.

2. Clean battery terminals.

3. Check all wiring.

4. Check/replace solenoid or starter.

1. Raise cutting height/reduce speed.

2. Adjust throttle control.

3. Clean underside of mower housing.

4. Clean/replace air filter.

5. Check oil levei/change oil.

Page 30

TROUBLESHOOTING CHART:

See appropriate section in manual unless directed to Sears service center

PROBLEM CAUSE CORRECTION

Loss of power

(cont.)

Excessive vibration

Engine dies when tractor is shifted into reverse

6. Faulty spark plug.

7. Dirty fuel filter.

8. Stale or dirty fuel.

9. Water in fuel.

10. Spark plug wire loose.

11. Dirty engine air screen/fins.

12. Dirty/clogged muffler.

13. Loose or damaged wiring.

14. Carburetor out of adjustment.

15. Engine valves out of adjustment.

1. Worn, bent or loose blade.

2. Bent blade mandrel.

3. Loose/damaged part(s).

1. Reverse operation system (ROS) is not "ON" while mower or other attachment is engaged.

6. Clean and regap or change

spark plug.

7. Replace fuel filter.

8. Empty fuel tank and refill tank

with fresh, clean gasoline.

9. Empty fuel tank and carbure tor, refill tank with fresh gas oline and replace fuel filter.

10. Connect and tighten spark plug wire.

11. Clean engine air screen/fins.

12. Clean/replace muffler.

13. Check all wiring.

14.See “To Adjust Carburetor” in Service and Adjustments

section.

15. Contact a Sears or other

qualified service center.

1. Replace blade. Tighten blade bolt.

2. Contact a Sears or other qualified service center.

3. tighten loose part(s).

Replace damaged parts.

1. Turn ignition key to ROS 't)N" position. See Operation section.

Engine continues to run when operator leaves seat with attachment clutch engaged

Poor cut - uneven 1. Worn, bent or loose blade.

1. Faulty operator-safety presence control system.

2. Mower deck not level.

3. Buildup of grass, leaves, and trash under mower.

4. Bent blade mandrel.

5. Clogged mower deck vent from build-up of grass, leaves, and trash around mandrels.

1. Check wiring, switches and connections. If not corrected, contact a Sears or other

qualified service center.

1. Replace blade. Tighten blade bolt.

2. Level mower deck.

3. Clean underside of mower housing.

4. Contact a Sears or other

q^ualified service center.

5. Clean around mandrels to

open vent holes.

Page 31

TROUBLESHOOTING CHART: See appropriate section in manual unless directed to Sears service center

PROBLEM CAUSE CORRECTION Mower blades will

not rotate

Poor grass discharge

Poor grass discharge (continued)

1. Obstruction in clutch mechanism.

2. Worn/damaged mower drive belt.

3. Frozen idler pulley.

4. Frozen blade mandrel.

1. Engine speed too slow.

2. Travel speed too fast.

3. Wet grass.

4. Mower deck not level.

5. Low/uneven tire air pressure.

6. Worn, bent or loose blade.

7. Buildup of grass, leaves and trash under mower.

8. Mower drive belt worn.

9. Blades improperly Installed.

10. Improper blades used.

11. Clogged mower deck vent holes from buildup of grass, leaves, and trash around mandrels.

1. Remove obstruction.

2. Replace mower drive belt.

3. Replace idler pulley.

4. Contact a Sears or other qualified service center.

1. Place throttle control in “FAST” position.

2. Shift to slower speed.

3. Allow grass to dry before mowing.

4. Level mower deck.

5. Check tires for proper air p^ressure.

6. Replace/sharpen blade.

Tighten blade bolt.

7. Clean underside of mower housing.

8. Replace mower drive belt.

9. Reinstall blades sharp edge down.

10. Replace with blades listed in this manual.

11. Clean around mandrels to open vent holes.

Headlight(s) not

working

(if so equipped)

1. Light switch is “OFF”.

2. Bulb(s) or lamp(s) burned out.

3. Faulty light switch.

4. Loose or damaged wiring.

5. Blown fuse.

Battery will not charge

1. Bad battery cell(s).

2. Poor cable connections.

3. Faulty regulator df so equipped).

4. haulty alternator.

Loss of drive 1. Freewheel control in

“disengaged” position.

2. Motion drive belt worn, damaged, or broken.

3. Air trapped in transmission during shipment or servicing.

Engine “backfires”

when turning

engine “OFF”

1. Engine throttle control not set between half and full speed (fast) position before stopping engine.

1. Turn light switch “ON”.

2. Replace buib(s) or lamp(s).

3. Check/repiace light switch.

4. Check wiring and connections.

5. Replace fuse.

1. Replace battery.

2. Check/clean all connections.

3. Replace regulator.

4. Replace alternator.

1. Place freewheel control in “engaged” position.

2. Replace motion drive belt.

3. Purge transmission.

1. Move throttle control between half and full speed (fast) position before stopping engine.

Page 32

SERVICE NOTES

Page 33

SCHEMATIC

02831 193372

TRACTOR - - MODEL NUMBER 917.275400

IGNITION SWITCH

POSITION CIRCUIT ‘MAKE”

OFF M+G+A1

RUN/OVERRIDE B+A1

RUN B+A1 L+A2

START B + S + A1

LIGHTING SYSTEM OUTPUT 5 AMP AC @ 3600 R PM DIODE

ORANGE

NOTE

YOUR TRACTOR IS EOUIPPED WITH A SPECIAL ALTERNATOR SYSTEM. THE LIGHTS ARE NOT CONNECTED TO THE BATTERY. BUT HAVE THEIR OWN ELECTRICAL SOURCE.

BECAUSE OF THIS, THE BRIGHTNESS OF THE LIGHTS WILL CHANGE WITH ENGINE SPEED. AT IDLE THE LIGHTS WILL DIM. AS THE ENGINE IS SPEEDED UP, THE LIGHTS WILL BECOME THEIR BRIGHTEST.

02831

V _ _ -----------1

^14 VOLTS AC MIN. @ 3600 RPM (LIGHTS OFF)

HEADLIGHTS

ALTERNATOR

...

NON-REMOVABLE

CONNECTIONS

WIRING INSULATED CLIPS

NOTE: IF WIRING INSULATED CLIPS

WERE REMOVED FOR SERVICING OF

UNIT, THEY SHOULD BE REPLACED

TO PROPERLY SECURE YOUR WIRING.

REMOVABLE

CONNECTIONS

Page 34

ELECTRICAL

REPAIR PARTS

TRACTOR - - MODEL NUMBER 917.275400

Page 35

ELECTRICAL

TRACTOR - - MODEL NUMBER 917.275400

KEY PART

NO. NO. DESCRIPTION

1 163465 Battery 2 74760412 Bolt Hex Hd 1/4-20 unc x 3/4 8 176689 Box Battery

16 176138 Switch, Interlock 21 183759 Harness Asm Light W/4152j 22 4152J Bulb Light #1156 24 4799J Cable Battery 6 Ga. 11" red 25 193149 Cable Battery 26 175158 Fuse 27 73510400 Nut Keps Hex 1/4-20 Unc 28 4207J Cable Ground 6 Ga. 12" black 29 192749 Switch Seat 30 193350 Switch Ign 33 140403 Key Ign 34 110712X Switch Light 40 193372 Harness Ign 41 71110408 Bolt BIk. Fin Hex 1/4-20 unc x 1/2 42 131563 Cover Terminal Red 43 178861 Solenoid 48 140844 Adapter Ammeter 52 141940 Protection Wire Loop 90 180449 Cover Terminal 92 193465 Harness Pigtail Reverse Switch 93 192540 Screw Plastic 10-14 x 2.0 94 191834 Module Reverse ROS

NOTE: All component dimensions given in U.S. inches

1 inch = 25.4 mm

Page 36

TRACTOR - - MODEL NUMBER 917.275400

CHASSIS AND ENCLOSURES

Page 37

TRACTOR - - MODEL NUMBER 917.275400

CHASSIS AND ENCLOSURES

KEY NO.

1 174619 Chassis

2 176554 Drawbar 5 155272 Bumper Hood/Dash 9 193510X012 Dash

10 STD533710 Bolt, Carriage 3/8-16 x 3/4 11 174996 Panel, Dash, L.H. 13 172105X010 Panel, Dash, R.H. 14 17490608 Screw Thdrol 3/8-16 x 1/2 17 185682X613 Hood Assembly 18 184921 Bumper Hood

24 STD523710 Bolt Fin, Hex 3/8-16 X 1 25 19131312 Washer 13/32 x 13/16 x 12 Ga. 26 STD541437 Nut 28 193258 Grille/Lens Asm. (Includes Key N' 29 174332X599 Lens 30 192528x613 Fend/Ftrest 31 136619 Bracket, Fender Support 33 179716X613 Footrest LH 34 179717X613 Footrest RH 35 STD533707 Bolt Rdhd Sht Sqnk 3/8-16 x 3/4 37 17490508 Screw Thdrol 5/16-18x1/2 38 175710 Pivot Bracket Assembly, Rear 39 174714 Bracket Pivot Laser Lt 64 154798 Dash Lower STLT

142 175702 Plate Reinforcement STLT 145 156524 Rod Pivot Chassis/Hood 159 169473X428 Cupholder

206 170165 Bolt Shoulder 5/16-18 TT 207 17670508 Screw Thdrol 5/16-18 x 1/2Tytt 208 17670608 Screw Thdrol 3/8-16 x 1/2 209 17000612 Screw Hexwsh Thdr 3/8-16 x 3/4 212 175143 Insert Lens Reflective 278 191611 Screw 10 X 3/4 Single Lead-Hex

- -

PART NO. DESCRIPTION

5479J Plug, Button 187801 Plug Plastic Dome

NOTE: All component dimensions given in U.S. inches

1 inch = 25.4 mm

Page 38

GROUND DRIVE

TRACTOR - - MODEL NUMBER 917.275400

Page 39

TRACTOR - - MODEL NUMBER 917.275400

GROUND DRIVE

KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. DESCRIPTION

1 Transaxle Peerless LTH2000

(See Breakdown)

8 192706 Rod Shift Fender

10 STD561210 Pin Cotter 1/8x1 CAD 14 10040400 Washer Lock Hvy Helical 15 74490544 Bolt Hex FLGHD 5/16-18 Gr.5 16 STD541431 Nut Lock Hex W/lns. 5/16-18 unc

19 STD541437 Nut Lock Hex W/Wsh 3/8-16 unc 21 130564 Knob 22 178141 Rod, Brake 24 73350600 Nut, Hex Jam 3/8-16 unc 25 106888X Spring, Brake Rod 27 STD561210 Pin Cotter 1/8 X 3/4 CAD. 28 175765 Rod, Parking Brake 29 71673 Cap, Parking Brake 30 174973 Bracket, Transaxle 32 74760512 Bolt Hex Hd 5/16-18 unc X 3/4 34 175578 Shaft, Foot Pedal 35 120183X Bearing, Nylon 36 19211616 Washer 37 1572H Pin, Roll 38 179114 Pulley, Composite 39 72110622 Bolt Rdhd 3/8-16 unc x 2-3/4 Gr. 5 41 175556 Keeper, Belt Idler 47 127783 Pulley, Idler, V-Groove 48 154407 Bellcrank, Clutch 49 123205X Retainer, Belt 50 72110612 Bolt Carr Sh 3/8-16 x 1-1/2 Gr 5 51 STD541437 Nut Crownlock 3/8-16 unc 52 STD541431 Nut, Crownlock 5/16-18 unc 53 10571 OX Link, Clutch 55 105709X Spring, Return, Clutch 56 17060620 Screw 3/8-16 x 1-1/4 57 178138 V-Belt 59 169691 Keeper, Center Span 61 17120614 Screw 3/8-16 X .875 62 8883R Cover, Pedal 63 175410 Pulley, Engine 64 173937 Bolt Hex 7/16-20x4 Gr.5 65 STD551143 Washer

66 154778 Keeper Belt Engine Hydro 69 142432 Screw HexWsh Hi-Lo 1/4-1/2 unc 70 134683 Keeper Belt Engine 74 137057 Spacer 75 121749X Washer 25/32 x 1-1/4 x 16 Ga. 76 STD581075 E-Ring 77 123583X Key, Square 78 121748X Washer 25/32 x 1-5/8 x 16 Ga, 81 178140 Shaft Asm Cross Tapered 82 123782X Spring Torsion 83 19171216 Washer 17/32 x 3/4 x 16 Ga. 85 150360 Nut Lock Center 1/4-28 FNTHD 89 192056X428 Console, Shift 95 178134 Disconnect Asm Rod Bypas LTH

112 19091210 Washer 9/32 x 3/4 x 10 Ga. 116 72140608 Bolt Rdhd Sqneck 3/8-16 x 1 120 73900600 Nut Lock Fig 3/8-16 150 175456 Spacer Retainer 151 19133210 Washer 13/32 x 2 x 10 Ga. 156 166002 Washer Srrted 5/16 ID X 1.125 158 165589 Bracket Shift Mount 159 183900 Hub Shift 161 72140406 Bolt Rdhd Sqnk 1/4-20 x 3/4 Gr. 5 162 73680400 Nut Crownlock 1/4-20 unc 163 74780416 Bolt Hex Fin 1/4-20 unc x 1 Gr. 5 165 165623 Bracket Pivot Lever 166 17490510 Screw 5/16-18 x 5/8 168 165492 Bolt Shoulder 5/16-18 x.561 169 165580 Plate Fastening

197 169613 Nyliner Snap-In 5/8”ID 202 72110614 Bolt Carr Sh 3/8-16 x 1-3/4 Gr.5 207 169845 Washer Nyl 212 145212 Nut Hex Flange Lock 245 178122 Strap Torque Lh LTH2000 246 178121 Strap Torque Rh LTH2000 247 181463 Link Shift Transaxle LTH2000 251 17060516 Screw 5/16-18 x 1 252 19131616 Washer 13/32x 1 x 16 Ga. 263 17000612 Screw Hex Wsh Thdr 3/8-16 x 3/4

NOTE: A!l component dimensions given in U.S, inches

1 inch = 25.4 mm

Page 40

STEERING ASSEMBLY

TRACTOR - - MODEL NUMBER 917.275400

-37

-36

Page 41

TRACTOR

STEERING ASSEMBLY

KEY PART NO. NO. DESCRIPTION

4 169839 Spindle Assembly, R.H.

40 73540600 Nut Crownlock 3/8-24 41 186737 Adaptor, Steering Wheel 42 145054X428 Boot, Steering Shaft 43 121749X Washer 25/32 x 1-1/4 x 16 Ga, 44 190752 Extension Shaft Steering 46 121232X Cap, Spindle 47 183226 Fitting Grease

MODEL NUMBER 917.275400

1 186780 Steering Wheel 2 175131 Axle Assembly 3 169840 Spindle Assembly, L.H.

5 6266H Washer Thrust 6 121748X Washer 25/32 x 1-5/8 x 16 Ga, 7 19272016 Washer 27/32 x 1-1/4 x 16 Ga. 8 12000029 Ring, Klip 9 3366R Washer Thrust

10 175121 Draglink

11 STD551137 Washer, Lock

13 136518 Spacer Bearing Axle Front

15 145212 Nut, Hex Flange Lock

17 190753 Shaft, Steering 26 126847X Bushing, Link, Drag 28 19131416 Washer 13/32 x 7/8 x 16 Ga. 29 17000612 Screw 3/8-16x3/4 30 STD561210 Pin Cotter 32 130465 Rod, Tie 34 10040500 Washer Lock Hvy. Hid Spr 5/16 36 155099 Bushing, Steering 37 152927 Screw 38 186781 Insert, Steering Wheel 39 19183812 Washer 9/16x2-3/8 12 Ga.

65 160367 Spacer Brace Axle 67 72110618 BoltRDHDSqnk 3/8-16x2-1/4 68 169827 Axle, Brace 71 175146 Steering Asm. 82 169835 Bracket Susp. Chassis Front 88 175118 Bolt Shoulder 7/16-20 unc 91 175553 Clip Steering 95 188967 Washer Hardened 97 74780564 Bolt 5/16-18 unc X 4 Gr. 5

NOTE: All component dimensions given in U.S. inches

1 inch = 25.4 mm

Page 42

ENGINE

TRACTOR - - MODEL NUMBER 917.275400

KEY PART NO. NO. DESCRIPTION

1 170545 Controi, Throttle/Choke 2 17720408 Screw, Hex Head, Thread

4 137352 Muffler

13 165291 Gasket 14 148456 Tube Drain Oi! Easy 23 169837 Shield Brn/Dbr Guard 29 137180 Arrestor, Spark 31 185115 Tank, Fuel 32 140527 Cap Assembly, Fuel Sears,

33 123487X Clamp, Hose

Cutting 1/4-20 X 1/2 Engine, Briggs Model 31H7770297-El (See Breakdown)

Vented

KEY PART

NO. NO. DESCRIPTION

37 137040 Line, Fuel 38 181654 Plug Drain Oil Easy 40 124028X Bushing, Snap, Fuel Line 44 17670412 Screw, Hex Washer Head,

Thd., Roil. 1/4-20x3/4 45 17000612 Screw Hxwsh Thdr 3/8-16 x 3/4 46 19091416 Washer 9/32 x 7/8 x 16 Ga. 62 10010500 Washer Split 72 71070512 Screw Hex Head Cap 5/16-18 x 3/4 78 17060620 Screw 3/8-16 X 1-1/4 81 73510400 Nut Keps Hex 1/4-20

NOTE: All component dimensions given in U.S. inches

1 inch = 25.4 mm

Page 43

SEAT ASSEMBLY

TRACTOR - - MODEL NUMBER 917.275400

KEY PART KEY PART

NO. NO. DESCRIPTION NO. NO. DESCRIPTION

1 188716 Seat 2 180166 Bracket Pnt Pivot Seat (bik ) 3 71110616 Bolt Fin Hex 3/8-16 unc x 1 4 19131610 Washer 13/32 x 3/4 x 10 Ga. 5 145006 Clip Push In Hinged 6 STD541437 Nut Hex Lock w/lns 3/8-16 unc 7 124181X Spring Seat Cprsn 2 250 BIk Zi 8 17000616 Screw 3/8-16 X 1 9 19131614 Washer 13/32x 1 x 14 Ga. 24 19171912 Washer 17/32 x 1-3/16 x 12 Ga.

1011180186

166369

Pan Pnt Seat (bik ) Knob Seat Adj Wingnut

12 174648 Bracket Pnt Mounting Switch 13 121248X Bushing Snap Bik Nyl 50 Id 14 72050412 Bolt Rdhd Sht Nk 1/4-20 x 1-1/2 15 134300 Spacer Split 28 x 96 Zinc 16 121250X Spring Cprsn 1 27 Bik Pnt

17 123976X Nut Lock 1/4 Lge Fig Gr. 5 Zinc 21 171852 Bolt Shoulder 5/16-18 unc-2A 22 STD541431 Nut Hex Lock w/lns 5/16-18

NOTE: Ail component dimensions given in U.S. inches

1 inch = 25.4 mm

Page 44

TRACTOR - - MODEL NUMBER 917.275400

DECALS

KEY

PART

NO.

NO. DESCRIPTION

1 193307 Decal, Oper. Instr. 13 183827 Decal, Dash Panel 2 193560 Decal, Replacement 14 160396 Decal, V-Belt Schematic 3 186280 Decal, Hood, R.H. 15 189100 Decal, Engine 4 186281 Decal, Hood, L.H. 16 172331 Decal, Mower Hvy. Duty 12 Ga, 5 179128 Decal, Deck "B" 42" 20 149516 Decal, Battery Dngr/Psn Eng 6 133644 Decal, Customer Maintenance 7 193545 Decal, Hood Side 9 186282 Decal, Fender, Craftsman

10 156439 Decal, Fender Danger

11 138047 Decal, Battery

12 146046 Decal, V-Belt Drive Schematic

PART

NO.

NO. DESCRIPTION

- -

138311 Decal, Lift Handle

- -

178392 Decal, Disconnect

- -

179768X428 Pad, Footrest LH STLT

- -

179769X428 Pad, Footrest RH STLT

- -

194154 Manual, Owner's, English 194155 Manual, Owner's, Spanish

- -

WHEELS & TIRES

KEY PART NO. NO.

1 2 3

9 10 11

59192 65139

106222X

59904

106732X624 278H 9040H

106108X624

106268X 7152J

104757X428

144334

DESCRIPTION

Cap Value Tire Stem Value Tire F Ts 15x6.0-6 Service Tube Inner Front #35060

Rim Asm 6” front White Service Fitting Grease Bearing Flange

Rim Asm 8” rear White Service Tire RTs 18x9 5-8 Service Tube Rear 9.5 x 8 Service Cap Axie BIk 1.50 x 1.00 Sealant, Tire (10 oz. tube)

NOTE: All component dimensions given in U.S. inches

1 inch = 25.4 mm

Page 45

LIFT ASSEMBLY

TRACTOR - - MODEL NUMBER 917.275400

KEY PART KEY PART

NO. NO. DESCRIPTION

1 159460 Washer Asm Inner Spring W/

2 159471 Shaft Asm. Lift 3 105767X Pin Groove 4 12000002 E Ring #5133-62 5 19211621 Washer 21/32 X 1 x21 Ga. 6 120183X Bearing Nylong 7 125631X Grip Handle Fluted 8 122365X Button Plunger Read

1112139865

139866

Plunger

Link Asm Lift L.H. Link Asm Lift R.H,

NO. NO. DESCRIPTION

13 STD624008 Retainer Spring 15 173288 Link Front 16 73350800 Nut Jam Hex 1/2-13 unc 17 175689 Trunnion BIk Zinc 18 73800800 Nut Lock w/Wsh 1/2-13 unc 19 139868 Arm Suspension Mower 20 163552 Retainer Spring

31 169865 Bearing, Pvt. Lift

32 73540600 Nut Crownlock 3/8-24

NOTE: All component dimensions given in U.S. inches

1 inch = 25.4 mm

Page 46

MOWER DECK

TRACTOR - - MODEL NUMBER 917.275400

Page 47

MOWER DECK

TRACTOR - - MODEL NUMBER 917.275400

KEY PART

NO. NO. DESCRIPTION

1 165892 Mower Deck Assembly, 42’’

2 STD533107 Bolt 3 138017 Bracket Assembly,Sway Bar,

Front 4 165460 Bracket Sway Bar 38/42” Deck 5 STD624008 Retainer Spring 6 178024 Bar Sway Deck 8 850857 Bolt, Hex 3/8-24 x 1.25 Gr. 8 9 STD551137 Washer, Lock

10 140296 Washer, Hardened

(The following baldes are availa ble)

11 138971 Blade, 42" Hi-Lift

(For bagging or discharging)

- - 134149 Blade, 42" Mulching Std

(For mulching mowers only)

- -

139775 Blade, 42" Mulching Premium

(For better wear when mulching) 13 137645 Shaft Assembly, Mandrel, Vented 14 128774 Housing, Mandrel, Vented 15 110485X Bearing, Ball, Mandrel 16 174493 Stripper, Vented Mower Deck 18 72140505 Bolt, Carriage 5/16-18 x 5/8 19 132827 Bolt, Shoulder

20 159770 Baffle, Vortex 21 STD541431 Nut Crownlock 5/16-18 unc 23 177563 Bracket, Deflector 24 105304X Cap, Sleeve 25 123713X Spring, Torsion, Deflector 26 110452X Nut, Push 27 130968X428 Shield, Deflector 28 19111016 Washer 11/32 x 5/8 x 16 Ga. 29 131491 Rod, Hinge 30 173984 Screw Thdrol Washer Head 31 187690 Washer, Spacer 32 153535 Pulley, Mandrel 33 178342 Nut, Toplock, Flanged

KEY PART

NO. NO. DESCRIPTION

34 72110612 Bolt Carr. Sh. 3/8-16 X 1-1/2 Gr. 5 36 131494 Pulley, Idler, Flat 40 73900600 Nut Lock 3/8-16 unc 44 140088 Guard, Mandrel, L.H. 45 STD624003 Retainer 46 137729 Screw, Thd. Roil 1/4-20x5/8 48 133944 Washer, Hardened 52 139888 Bolt, Shoulder 5/16-18 unc 53 184907 Arm Assembly, Pad, Brake 54 178515 Washer, Hardened 55 155046 Arm, Idler 56 165723 Spacer, Retainer 59 141043 Guard, TUV Idler 67 149846 Knob Custom Oval 68 144959 V-Be!t

142 165890 Arm Spring Brake Mower 143 157109 Bracket Arm Idler 42” 144 158634 Keeper Belt 42” Clutch Cable 145 165888 Pulley Idler Flat 146 171977 Bolt Carriage Idler 147 131335 Spring Extension 148 169022 Spring Return Idler 149 165898 Retainer Spring Yellow Zinc 150 19091210 Washer 9/32 x 3/4 x 10 Ga. 152 169676 Cable Clutch 42 In 158 17720408 Screw Hex Thd Cut 1/4-20 x 1/2 159 72140614 Bolt Rdhd Sqn 3/8-16 unc x 3/4 184 19131410 Washer 13/13 x7/8x 10 Ga. 185 188234 Head Asm Cable Clutch

- -

130794 Mandrel Assembly (Includes

Housing, Shaft and Shaft Hardware Only - Pulley Not Included)

- -

171639 Replacement Mower, Complete

NOTE: Al! component dimensions given in U.S. inches

1 inch = 25.4 mm

Page 48

TRACTOR--MODEL NUMBER 917.275400

PEERLESS TRANSAXLE - - MODEL NUMBER LTH2000

■# 41

r--' 25 42A

‘»iB 36

^ A

[\-45

AAA

} V' i /|'!J

‘ V.,1,

38 37

180'^

150

Page 49

TRACTOR--MODEL NUMBER 917.275400

PEERLESS TRANSAXLE - - MODEL NUMBER LTH2000

KEY PART NO. NO. DESCRIPTION

1 772151 Cover L.H. 3 770135 Case 5 776355 Counter Shaft 6 778263 Spur Gear11T 9 786197 Neutral Sleeve (.572)

13 778368 Bevel Gear(lncl. 14) (13 Teeth)

14 778368 Bevel Gear(lncl. 13) (13 Teeth)

15 778373 Ring Gear (54 Teeth)

17 786139 Drive Pin 22 792194 Spring 23 792195 Washer .750 ID 25 792073A Screw 1/4-20 x 1-1/4” 26 792125 Retaining Ring 28 792035 Retaining Ring 29 780065 Washer .627 ID .091W 31 780189 Washer .563 ID .062W 36 790071 Brake Disk 37 790007 Brake Pad Plate 38 799021 Brake Pad 40 792204 Roll Pin .25 41 790102 Brake Lever 42 792202 Screw, 1/4-20 x 3/4 42A 792203 Screw, 1/4-20 x 1-3/4 43 792171 Screw, 10-24 x .500 44A 790100 Inside Brake (Mach) 44B 790099 Outside Brake (Casting) 45 790101 Actuator Rod 47 774869 Axle 16.812 48 774688 Axle 11.625 49 778378 Spur Gear 18T 56 778379 Spur Gear 81T 65 780195 Washer .750ID .062W 67 776440 Brakeshaft

KEY PART NO. NO. DESCRIPTION

70 786196 Spacer .625 .765 79 792201 Spring 85 792154 Oil Fill Plug 87 788088A Oil Seal 3/4” 99 792141 Washer .377ID .058W

100 792200 Snubber Washer 101 792199 Snubber Spring .47ID 102 792184 Washer .437ID .078W 103 792193 Screw, 1/4-28 x .490 104 792198 Nut, 3/8-24 105 780096 Washer .625 ID .057W 106 786162 Sleeve Assembly 107 792046 Screw, 1/4-20 x 1” 109 788104 “O” Ring 113 786199 Sleeve Ass’y (Incl. 157) 114 786200 Sleeve Ass’y ^ncl. 87) 115 786198 Sleeve Assembly (Incl. 87) 127 784384 Shift Lever Ass'y (Incl. 109) 150 788093A Liquid Gasket RTV Silicon 157 788102 Oil Seal 9/16”ID 180 730229 BOH Spec. (80W90) 182 788103 Grommet 183 792118 Relief Valve 184 792196 Hose Barb 185 798050 Tubing 1/2x5 190 792150 Washer 191 792151 Nut 7/16-20

200 794787 Differential (Gear Reduction

Drive) 203 798044 Pulley & Hub Ass’y 206 798055 Disconnect Lever 207 798053 Mounting Plate 208 798040 Fan 209 798054 Control Lever 210 794788 Hydro Module LH Fender Cc

trai

Page 50

TRACTOR--MODEL NUMBER 917.275400

BRIGGS & STRATTON ENGINE-MODEL NUMBER 31H777,TYPE NUMBER 0297-El

1019 LABEL KIT

1058 OWNER’S MANUAL

I 1036 EMISSION label"

1024

965

943 0

750*

1027

Page 51

TRACTOR - - MODEL NUMBER 917.275400

BRIGGS & STRATTON ENGINE-MODEL NUMBER 31H777, TYPE NUMBER 0297-El

729

1070 S

Page 52

TRACTOR--MODEL NUMBER 917.275400

BRIGGS & STRATTON ENGINE-MODEL NUMBER 31H777,TYPE NUMBER 0297-El

977 CARBURETOR GASKET SET

137 I

276 I

240

187

527

6011

Page 53

TRACTOR--MODEL NUMBER 917.275400

BRIGGS & STRATTON ENGINE-MODEL NUMBER 31H777,TYPE NUMBER 0297-El

KEY PART NO. NO. DESCRIPTION

1 697174 Cylinder Assembly 2 399265 Kit-Bushing/Seal (Magneto Side) 3 391086 • Seal-Oil (Magneto Side) 4 697188 Sump-Engine 5 698147 Head-Cylinder 7 699168 •+ Gasket-Cylinder Head 9 697109 • Gasket-Breather

11 697113 Tube-Breather

12 697110 • Gasket-Crankcase

13 690360 Screw (Cylinder Head)

15 690946 Plug-Oil Drain

16 697127 Crankshaft 20 690947 • Seal-Oil (PTO Side) 22 692125 Screw (Crankcase Cover/Sump) 23 693557 Flywheel 24 222698 Key-Flywheel 25 699052 Piston Assembly (Standard)

26 699051 Ring Set (Standard)

-- 697559 Ring Set ¿020” Oversize) 27 698469 Lock-Piston Pin 28 697099 Pin-Piston 29 697126 Rod-Connecting (Standard)

-32 692852 Screw (Connecting Rod)

33 695760 Valve-Exhaust 34 695761 Valve-Intake 35 691279 Spring-Valve (Intake) 36 691279 Spring-Valve (Exhaust) 37 697108 Guard-Flywheel 40 691752 Retainer-Valve 43 691968 Slinger-Governor/Oil 45 690564 Tappet-Valve 46 698492 Camshaft 48 697762 Short Block 50 690193 Manifold-Intake 51 692137 >0t+Gasket-Intake 53 690227 Stud (Carburetor) 54 691148 Screw (Intake Manifold) 73 697133 Screen-Rotating 74 697897 Screw (Rotating Screen) 78 691003 Screw (Flywheel Guard) 89 690283 Plug-Oil 93 690602 0 Bushing-Throttle Shaft 94 498030 Kit-ldle Mixture 94A 695425 Kit-Idle Mixture (Nikki) 95 691636 Screw (Throttle Valve) 95A 690718 0 Screw (Throttle Valve (Nikki) 98 495800 Kit-Idle Speed • 98A 695408 Kit-ldle Speed (Nikki)

104 690525 0 Pin-Float Hinge

104A 694918 0 Pin-Float Hinge (Nikki)

105 231855 0 Valve-Float Needle

105A 696136 0 Valve-Float Needle (Nikki) +

699054 Piston Assembly

(.020” Oversize)

697263 Rod-Connecting

(.020” Undersize)

KEY PART NO. NO. DESCRIPTION

106 690577 0 Seat-Inlet 108 690464 Valve-Choke (Manual Choke) 108A 695419 Valve-Choke (Nikki) 117 694352 0 Jet-Main (Standard) 117A 699457 0 Jet-Main (Standard) (Nikki) 118 697228 Jet-Main (High Altitude) 118A 699458 Jet-Main (High Altitude) (Nikki) 121 697241 Kit-Carburetor Overhaul 121A 699521 Kit-Carburetor Overhaul (Nikki) 125 698445 Carburetor 125A Carburetor (For Complete

Carburetor, Service with

698445) 127 695005 Plug-Welch 127A 690727 0 Plug-Welch (Nikki) 130 691750 Valve-Throttle 130A 699500 Valve-Throttle (Nikki) 131 494379 Kit-Throttle Shaft 131A 699501 Kit-Throttle Shaft (Nikki) 133 494381 Float-Carburetor 133A 694914 Float-Carburetor (Nikki) 135 698780 Tube-Fuel Transfer 137 281165 0t Gasket-Float Bowl 137A 698781 0 Gasket-Float Bowl (Nikki) 141 495097 Kit-Choke Shaft (Manual Choke) 141A 698778 Kit-Choke Shaft (Nikki) 142 697140 0 Nozzle-Carburetor 146 691639 Key-Timing 187 697098 Line-Fuel 188 691693 Screw (Control Bracket) 192 691986 Adjuster-Rocker Arm

202 691841 Link-Mechanical Governor 209 692208 Spring-Governor 216 691840 Link-Choke 222 694042 Bracket-Control 227 691374 Lever-Governor Control 231 691636 Screw (Choke Valve) 232 691842 Spring-Governor 238 691843 Cap-Valve 240 394358 Filter-Fuel 265 691024 Clamp-Casing 267 695134 Screw (Casing Clamp) 276 692255 0i Washer-Sealing 276A 695410 Washer-Sealing 304 697783 Housing-Blower 305 697102 Screw (Blower Housing) 305A 697103 Screw (Blower Housing) 306 697107 Shield-Cylinder 307 691003 Screw (Cylinder Shield)

Included in Engine Gasket Set, Key. No. 358

0 Included in Carburetor Overhaul Kit, Key. No.

121

Included in Carburetor Gasket Set, Key. No. 977 Included in Valve Gasket Set, Key. No. 1095

NOTE: All component dimensions given in U.S. inches

1 inch = 25.4 mm

Page 54

TRACTOR--MODEL NUMBER 917.275400

BRIGGS & STRATTON ENGINE-MODEL NUMBER 31H777,TYPE NUMBER 0297-El

KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. DESCRIPTION

309 693551 Motor-Starter 868 690968 •+ Seal-Valve 310 690323 Bolt (Starter Motor) 914 690960 Screw (Rocker Cover) 311 497608 Brush Set 943 690589 • Seal-O Ring (Oil Pump Cover) 333 495859 Armature-Magneto 947 694393 Solenoid-Fuel 334 691061 Screw (Magneto Armature) 947A 695423 Solenoid-Fuel (Nikki) 337 691043 Plug-Spark 950 691657 Screw (Float Bowl) 358 697191 Gasket Set-Engine 965 499613 Cover-Oil Pump 363 19203 Flywheel Puller 383 89838 Wrench-Spark Plug 968 697446 Cover-Air Cleaner 404 691691 Washer (Governor Crank) 975 495933 Bowl-Float 431 697122 El bow-Intake 975A 699502 Bowl-Float (Nikki) 445 697634 Filter-Air Cleaner Cartridge 977 690192 Gasket Set-Carburetor 462 691261 Washer (Starter Cable) 474 696459 Alternator 987A 698777 0 Seal-Throttle Shaft (Nikki) 503 691532 Strap-Starter 1005 697111 Fan-Flywheel 505 691251 Nut (Governor Control Lever) 1017 690770 Screen-Oil Pump 510 693699 Drive-Starter 1019 698814 Kit-Label 513 692024 Clutch-Drive 1022 272475 •+ Gasket-Rocker Cover 523 697086 Dipstick 1023 692492 Cover-Rocker Arm 524 691032 • Seal-Dipstick Tube 1024 499054 Pump-Oil 525 697184 Tube-Dipstick 1026 692003 Rod-Push (Intake) 527 698467 Clamp-Tube 692011 Rod-Push (Exhaust) 544 692034 Starter-Armature 1027 492932 Filter-Oil 552 697144 Bushing-Governor Crank 559 693675 Screw (Remote Choke Stop) 1034 690822 Guide-Push Rod 562 691119 Bolt (Governor Control Lever) 1035 693784 Shaft-Pump 579 691029 Nut (Starter Cable) 1036 695700 Label-Emission 584 697112 Cover-Breather Passage 1040 698368 Plate-Trim 601 95162 Clamp-Hose 1044 698139 Screw (Flywheel) 614 691620 Pin-Cotter 1051 691265 Ring-Retaining 616 692012 Crank-Governor 1058 275038 Owner’s Manual 617 692138 0* Seal-O Ring (Intake Manifold) 1059 698516 Kit-Screw/Washer 634 690801 0 Spring/Seal Assembly 1070 690372 Screw (Flywheel Fan)

(Manual Choke) 1090 691293 Retainer-Brush 634A 698779 0 Spring/Seal Assembly (Nikki) 1091 691333 Cap-Limiter 635 691909 Boot-Spark Plug 1095 690190 Gasket Set-Valve 643 697417 Retainer-Air Filter 1119 691183 Screw (Alternator) 654 690958 Nut (Carburetor) 1127 695407 Screw-Float Bowl 684 697157 Screw (Breather Passage Cover) 1263 697124 Reed-Breather 691 692407 • Seal-Governor Shaft 692 690572 Spring-Detent 1265 697125 Support-Blower Housing 697 690372 Screw (Drive Cap) 1266 691917 -0 Seal-O Ring (Intake Elbow) 718 690959 Pin-Locating 1266A 697123 0 Seal-O Ring (Intake Elbow) 729 691224 Clip-Wire 1267 697662 Latch-Blower Housing 741 697128 Gear-Timing 750 691033 Screw (Oil Pump Cover) 1279 690960 Screw (Blower Housing Support) 757 697607 Link-Counterweight 1329 31H777-0202 Replacement Engine 758 697134 Counterweight 1330 272147 Repair Manual 759 697392 Pin-Counterweight 783 693713 Gear-Pinion 789 698329 Harness-Wiring 0 Included in Carburetor Overhaul Kit, Key. No. 797 693167 Nut (Brush Retainer) 121 801 691283 Cap-Drive Included in Carburetor Gasket Set, Key. No. 802 691286 Cap-End 977 803 693757 Housing-Starter 830 691095 Stud (Rocker Arm) 842 691031 • Seal-O Ring (Dipstick Tube) NOTE: All component dimensions given in U.S. inches 847 697611 Dipstick/Tube Assembly 1 inch = 25.4 mm 851 692424 Terminal-Spark Plug

967 697015 Filter-Pre Cleaner

987 691326 0 Seal-Throttle Shaft

1029 691751 Arm-Rocker

1264 697104 Screw (Breather Reed)

1270 697156 Plug-AVS Counterweight

•

Included in Engine Gasket Set, Key. No. 358

Included in Valve Gasket Set, Key. No. 1095

Page 55

SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION

can

ONLY RIDE UP AND DOWN HILL NOT ACROSS HILL

15 DEGREES MAX.

VVVVVVVVVVVVVVVVYVVVVVVVVVVVVVVVVVVVVV>VVVVVVVVVVVVVVVVVVVVVVVVVVV»VVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVV>VVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVV7

WARNING: To avoid serious injury, operate your tractor up and down the face of slopes, never across the face. Do not mow slopes greater than 15 degrees. Make turns gradually to prevent tipping or loss of control. Exercise extreme caution when changing direction on slopes.

1. Fold this page along dotted line indicated above.

2. Hold page before you so that its left edge is vertically parallel to a tree

trunk or other upright structure.

3. Sight across the fold in the direction of hill slope you want to measure.

4. Compare the angle of the fold with the slope of the hill.

■VWVVVVVVVVV^^

Page 56

Get it fixed, at your home or ours!

Your Home

For repair - in your home - of all major brand appliances,

lawn and garden equipment, or heating and cooling systems,

no matter who made it, no matter who sold it!

For the replacement parts, accessories and

owner’s manuals that you need to do-it-yourself.

For Sears professional installation of home appliances

and items like garage door openers and water heaters.

1-800-4-MY-HOME® Anytime, day or night

(1-800-469-4663) (U.S.A. and Canada)

www.sears.com www.sears.ca

Our Home

For repair of carry-in products like vacuums, lawn equipment,

and electronics, call or go on-line for the nearest

Sears Parts and Repair Center.

1 -800-488-1222 Anytime, day or night (U.S.A. only)

www.sears.com

To purchase a protection agreement (U.S.A.)

or maintenance agreement (Canada) on a product serviced by Sears:

1-800-827-6655 (U S A.) 1-800-361-6665 (Canada)

Para pedir servicio de reparación

a domicilio, y para ordenar piezas:

1-888-SU-HOGARS^

(1-888-784-6427)

® Marca Registrada / ™ Marca de Fábrica / Marca de Servicio de Sears, Roebuck and Co.

Marque de commerce / “° Marque déposée de Sears, Roebuck and Co.

Au Canada pour service en français:

"I -80Q"LE-FOYER

(1-800-533-6937)

www.sears.ca

194154 Rev. 1 09.23.04 TR Printed in U.S.A.

Craftsman 917.275400 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

Owner’s Manual

IMPORTANT:

PRODUCT SPECIFICATIONS

CUSTOMER RESPONSIBILITIES

SEARS INSTALLATION SERVICE

UNASSEMBLED PARTS

ASSEMBLY/PRE-OPERATION

OPERATION

PURGE TRANSMISSION

MOWING TIPS

MAINTENANCE

GENERAL RECOMMENDATIONS

BEFORE EACH USE

LUBRICATION CHART

TRACTOR

ENGINE

CLEANING

SERVICE AND ADJUSTMENTS

ENGINE

STORAGE

REPAIR PARTS

SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION

Your Home

Our Home