Craftsman 917.273770 User Manual

Owner’s Manual

CRRFTSMRN

LAWN TRACTOR

22.0 HP, 42” Mower Electric Start 6 Speed Transaxle

Model No.

91 y 273770

This product has a low emission engine which operates
differently from previously built engines. Before you start the
engine, read and understand this Owner’s Manual.

IMPORTANT:

Read and follow all Safety
Rules and Instructions before

operating this equipment.

Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.

Visit our Craftsman website:www.sears.com/craftsman

For answers to your questions about

this product, Caii:

1-800-659-5917

Sears Craftsman Help Line

5 am - 5 pm, Mon - Sat

..................................

Warranty.........................

Safety Rules

....................

Product Specifications....

Assembly/Pre-Operation

Operation........................

Maintenance Schedule...

...2
...3

...6

...8

.11

.17

Maintenance...................

Service and Adjustments
Storage

............................

Troubleshooting..............

Repair Parts....................

Sears Service

..................

....17

....21

....27

....28

....32

.Back Cover

LIMITED WARRANTY ON CRAFTSMAN RIDING EQUIPMENT
For two (2) years from the date of purchase, if this Craftsman Riding Equipment is

maintained, lubricated and tuned up according to the instructions in the owner’s manual.
Sears will repair or replace free of charge any parts that are found to be defective in
materia! or workmanship according to the guidelines of coverage listed below. Sears will
also provide free labor for these applicable warranted parts for the two full years. During
the first 30 days of purchase, there will be no charges to service the product at your
home for issues covered by this warranty. (See exclusions below). For your conve
nience, IN HOME warranty service will still be available after the first 30 days of pur
chase, but a trip charge will apply. This charge will be waived if the Craftsman product is
dropped off at an authorized Sears location. For the nearest authorized Sears location,
please call 1-800-4-MY-HOME®. This warranty applies only while this product is within
the United States.

This Warranty does not cover:

• Expendable items which become worn during norma! use, including but not limited to
blades, spark plugs, air cleaners, belts, and oil filters.

• Standard Maintenance Servicing, oil changes, or tune-ups

• Tire replacement or repair caused by punctures from outside objects, such as nails,
thorns, stumps, or glass.

• Repairs necessary because of operator abuse, including but not limited to, damage
caused by towing objects beyond the capability of the riding equipment, impacting
objects that bend the frame or crankshaft, or over-speeding the engine.

• Repairs necessary because of operator negligence, including but not limited to, elec
trical and mechanical damage caused by improper storage, failure to use the proper
grade and amount of engine oil, failure to keep the deck clear of flammable debris,
or failure to maintain the equipment according to the instructions contained in the
owner’s manual.

• Engine (fuel system) cleaning or repairs caused by fuel determined to be contami
nated or oxidized (stale). In genera!, fuel should be used within 30 days of its pur
chase date.

• Normal deterioration and wear of the exterior finishes, or product label replacement.

• Riding equipment used for commercial or rental purposes.

LIMITED WARRANTY ON BATTERY
For ninety (90) days from date of purchase, if any battery included with this riding equip
ment proves defective in material or workmanship and our testing determines the battery
will not hold a charge. Sears will replace the battery at no charge. During the first 30
days of purchase, there will be no charges to replace the battery at your HOME. After
the first 30 days, for your convenience, IN-HOME warranty service will still be avail
able but a trip charge will apply. This charge will be waived if the Craftsman product is
dropped off at an authorized Sears location. For the nearest authorized Sears location,
please call 1-800-4-MY-HOME®.

This battery warranty applies only while this product is within the United States.
This warranty gives you specific legal rights, and you may also have other rights, which

vary, from state to state.
Sears, Roebuck and Co.,Dept.817WA, Hoffman Estates, IL 60179

2

IMPORTANT: This cutting machine is capable of amputating hands and feet and throw
ing objects. Failure to observe the following safety instructions could result in serious
injury or death.

AwaRNING: In order to prevent acciden

tal starting when setting up, transporting,
adjusting or making repairs, always
disconnect spark plug wire and place wire
where it cannot contact spark plug.

AwARNING: Do not coast down a hill in

neutral, you may lose control of the tractor.

AwaRNING: Tow only the attachments

that are recommended by and comply with
specifications of the manufacturer of your
tractor. Use common sense when towing.
Operate only at the lowest possible speed
when on a slope. Too heavy of a load,
while on a slope, is dangerous. Tires can
lose traction with the ground and cause
you to lose control of your tractor.

AwaRNING: Engine exhaust, some of its

constituents, and certain vehicle compo
nents contain or emit chemicals known to
the State of California to cause cancer and
birth defects or other reproductive harm.

AwaRNING: Battery posts, terminals and

related accessories contain lead and lead
compounds, chemicals known to the State
of California to cause cancer and birth
defects or other reproductive harm. Wash

hands after handling.

Be aware of the mower discharge direc
tion and do not point it at anyone. Do
not operate the mower without either
the entire grass catcher or the guard in
place.
Slow down before turning.

Never leave a running machine unat
tended. Always turn off blades, set
parking brake, stop engine, and remove
keys before dismounting.
Turn off blades when not mowing.
Stop engine before removing grass
catcher or unclogging chute.
Mow only in daylight or good artificial
light.

Do not operate the machine while under
the influence of alcohol or drugs.
Watch for traffic when operating near or
crossing roadways.

Use extra care when loading or un
loading the machine into a trailer or
truck.

Data indicates that operators, age 60
years and above, are involved in a large
percentage of riding mower-related in
juries. These operators should evaluate
their ability to operate the riding mower
safely enough to protect themselves and

I. GENERAL OPERATION

• Read, understand, and follow all instruc
tions in the manual and on the machine
before starting.

• Only allow responsible adults, who are
familiar with the instructions, to operate
the machine.

• Clear the area of objects such as rocks,
toys, wire, etc., which could be picked
up and thrown by the blade.

others from serious injury.

• Keep machine free of grass , leaves or
other debris build-up which can touch
hot exhaust / engine parts and burn . Do
not allow the mower deck to plow leaves
or other debris which can cause build
up to occur. Clean any oil or fuel
spillage before operating or storing the
machine . Allow machine to cool before
storage.

• Be sure the area is clear of other people
before mowing. Stop machine if anyone
enters the area.

• Never carry passengers.

• Do not mow in reverse unless abso
lutely necessary. Always look down and
behind before and while backing.

II slope operation

Slopes are a major factor related to loss­of-control and tipover accidents, which can

result in severe injury or death. All slopes

require extra caution. If you cannot back
up the slope or if you feel uneasy on it, do
not mow it.

DO:

• Mow up and down slopes, not across.

• Remove obstacles such as rocks, tree
limbs, etc.

• Watch for holes, ruts, or bumps. Un
even terrain could overturn the machine.

Tall grass can hide obstacles.

• Use slow speed. Choose a low gear

so that you will not have to stop or shift
while on the slope.

• Follow the manufacturer’s recommend
ations for wheel weights or counter
weights to improve stability.

• Use extra care with grass catchers or
other attachments. These can change
the stability of the machine.

• Keep all movement on the slopes slow
and gradual. Do not make sudden
changes in speed or direction.

• Avoid starting or stopping on a slope. If
tires lose traction, disengage the blades
and proceed slowly straight down the
slope.

DO NOT:

• Do not turn on slopes unless neces
sary, and then, turn slowly and gradually
downhill, if possible.

• Do not mow near drop-offs, ditches,
or embankments. The mower could
suddenly turn over if a wheel is over
the edge of a cliff or ditch, or if an edge
caves in.

• Do not mow on wet grass. Reduced
traction could cause sliding.

• Do not try to stabilize the machine by
putting your foot on the ground.

• Do not use grass catcher on steep
slopes.

III. CHILDREN

Tragic accidents can occur if the operator
is not alert to the presence of children.
Children are often attracted to the ma
chine and the mowing activity. Never as
sume that children will remain where you
last saw them.

• Keep children out of the mowing area
and under the watchful care of another
responsible adult.

• Be alert and turn machine off if children
enter the area.

• Before and when backing, look behind
and down for small children.

• Never carry children. They may fall off
and be seriously injured or interfere with
safe machine operation.

• Never allow children to operate the
machine.

• Use extra care when approaching blind
corners, shrubs, trees, or other objects
that may obscure vision.

IV. SERVICE

• Use extra care in handling gasoline and
other fuels. They are flammable and
vapors are explosive.

- Use only an approved container.

- Never remove gas cap or add fuel
with the engine running. Allow
engine to cool before refueling. Do
not smoke.

- Never refuel the machine indoors.

- Never store the machine or fuel con

tainer inside where there is an
open flame, such as a water heater.

• Never run a machine inside a closed
area.

• Keep nuts and bolts, especially blade
attachment bolts, tight and keep equip
ment in good condition.

• Never tamper with safety devices.
Check their proper operation regularly.

• Keep machine free of grass, leaves, or
other debris build-up. Clean oil or fuel
spillage. Allow machine to cool before
storing.

• Stop and inspect the equipment if you
strike an object. Repair, if necessary,
before restarting.

• Never make adjustments or repairs with
the engine running.

• Grass catcher components are subject
to wear, damage, and deterioration,
which could expose moving parts or
allow objects to be thrown. Frequently
check components and replace with
manufacturer's recommended parts,
when necessary.

• Mower blades are sharp and can cut.
Wrap the biade{s) or wear gloves, and
use extra caution when servicing them.

• Check brake operation frequently. Ad
just and service as required.

Be sure the area is clear of other people
before mowing. Stop machine if anyone
enters the area.
Never carry passengers or children
even with the blades off.
Do not mow in reverse unless abso
lutely necessary. Always look down and
behind before and while backing.
Never carry children. They may fall off
and be seriously Injured or interfere with
safe machine operation.
Keep children out of the mowing area
and under the watchful care of another
responsible adult.
Be alert and turn machine off if children
enter the area.
Before and when backing, look behind
and down for small children.
Mow up and down slopes {15° Max), not
across.

Remove obstacles such as rocks, tree
limbs, etc.
Watch for holes, ruts, or bumps. Uneven
terrain could overturn the machine. Tall
grass can hide obstacles.

Use slow speed. Choose a low gear
so that you wiil not have to stop or shift
while on the slope.
Avoid starting or stopping on a slope. If
tires lose traction, disengage the blades
and proceed slowly straight down the
slope.

If machine stops while going uphill,
disengage blades, shift into reverse and
back down slowly.

Do not turn on slopes unless necessary,
and then, turn slowly and gradually
downhill, if possible.

PRODUCT SPECIFICATIONS

Gasoline Capacity 3.5
and Type: Unleaded Regular

Oil Type
(APl-SF-SJ):

Oil Capacity:

Spark Plug:
(Gap: .040’’)

Ground Speed Forward:
(MPH);

Tire Pressure: Front; 14PSI

Charging
System:

Battery; Amp/Hr: 35

Blade Bolt Torque: 27-35 Ft. Lbs.

CONGRATULATIONS on your purchase
of a new tractor. It has been designed,
engineered and manufactured to give you the
best possible dependability and performance.
Should you experience any problem you
cannot easily remedy, please contact a
Sears or other qualified service center.
We have competent, well-trained techni
cians and the proper tools to service or
repair this tractor.
Please read and retain this manual. The
instructions will enable you to assemble
and maintain your tractor properly. Always
observe the “SAFETY RULES”.

CUSTOMER RESPONSIBILITIES

• Read and observe the safety rules.

• Follow a regular schedule in main
taining, caring for and using your tractor.

• Follow the instructions under “Mainte

nance” and “Storage” sections of this

owner’s manual.

^WARNING: This tractor is equipped with
an internal combustion engine and should
not be used on or near any unimproved for
est-covered, brush-covered or grass-covered
land unless the engine’s exhaust system is
equipped with a spark arrester meeting ap
plicable local or state laws (if any). If a spark
arrester is used, it should be maintained in
effective working order by the operator.

SAE 30 {above 32T)
SAE 5W-30
(below 32° F)

W/Filter;

W/0 Filter; 3.75 Pints

Champion QC12YC

1st
2nd 1.5

3rd
4th
5th
6th

Rear: 10PSI
3 Amps Battery

5 Amps Headlights

Min. CCA: 280
Case SizeiUIR

4.0 Pints

1.2

2.4

3.5

4.8

5.3

1.5

In the state of California the above is re
quired by law (Section 4442 of the Califor
nia Public Resources Code). Other states
may have similar laws. Federal laws apply
on federal lands. A spark arrester for the
muffler is available through your nearest
Sears service center (See REPAIR PARTS
section of this manual).

REPAIR PROTECTION AGREEMENTS

Congratulations on making a smart pur
chase. Your new CraftsmaiTD product is
designed and manufactured for years of
dependable operation. But like all products,
it may require repair from time to time. That’s
when having a Repair Protection Agreement
can save you money and aggravation.

Purchase a Repair Protection Agreement
now and protect yourself from unexpected
hassle and expense.

Here’s what’s included in the Agreement;

• Expert service by our 12,000 profe
sional repair specialists.

• Unlimited service and no charge for
parts and labor on all covered repairs.

• Product replacement if your covered
product can’t be fixed.

• Discount of 10% from regular price of
service and service-related parts not
covered by the agreement; also, 10%
off regular price of preventive mainte

nance check.

• Fast help by phone - phone support
from a Sears technician on products

requiring in-home repair, plus conve

nient repair scheduling.
Once you purchase the Agreement, a
simple phone call is all that it takes for you
to schedule service. You can call anytime
day or night, or schedule a service ap
pointment online.
Sears has over 12,000 professional repair
specialists, who have access to over 4.5
million quality parts and accessories.
That’s the kind of professionalism you can
count on to help prolong the life of your
new purchase for years to come. Purchase
your Repair Protection Agreement today!

Some limitations and exclusions apply.
For prices and additional Information
call 1-800-827-6655.

SEARS INSTALLATION SERVICE

For Sears professional installation of home
appliances, garage door openers, water
heaters, and other major home items, in
the U.S.A. call 1-800-4-IVIY-HOME®

Your new tractor has been assembied at the factory with the exception of those parts ieft
unassembled for shipping purposes. To ensure safe and proper operation of your tractor
all parts and hardware you assemble must be tightened securely. Use the correct tools
as necessary to insure proper tightness. Review the video cassette before you begin.

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assembly
easier. Standard wrench sizes you need
are listed below.

(1) 3/4" wrench (1) Pliers
(2) 7/16" wrench (1) Utility knife
(1) Tire pressure gauge

When right or left hand is mentioned in
this manual, it means when you are in
the operating position (seated behind the
steering wheel).

TO REMOVE TRACTOR FROM
CARTON

UNPACK CARTON

1. Remove all accessible loose parts and
parts boxes from carton.

2. Cut along dotted lines on all four pan
els of carton. Remove end panels and
lay side panels flat.

3. Check for any additional loose parts or
cartons and remove.

BEFORE REMOVING TRACTOR FROM SKID

ATTACH STEERING WHEEL

ASSEMBLE EXTENSION SHAFT AND

BOOT

1. Slide extension shaft onto lower steer
ing shaft. Align mounting holes in ex
tension and lower shafts and install 1/4
hex bolt and locknut. Tighten securely.

IMPORTANT: Tighten bolt and nut se

curely to 10-12 ft. lbs torque.

2. Place tabs of steering boot over tab
slots in dash and push down to secure.

INSTALL STEERING WHEEL

3. Position front wheels of the tractor so
they are pointing straight forward.

4. Remove steering wheel adapter from
steering wheel and slide adapter onto
steering shaft extension.

5. Position steering wheel so cross bars
are horizontal (left to right) and slide
inside boot and onto adapter.

6. Assemble large flat washer, 1/2 hex
nut and tighten securely.

7. Snap steering wheel insert into center
of steering wheel.

8. Remove protective materials from trac
tor hood and grill.

IMPORTANT: Check for and remove any
staples in skid that may puncture tires
where tractor is to roll off skid.

HOWTO SET UP YOUR TRACTOR
CHECK BATTERY

1. Lift hood to raised position.
NOTE: If this battery is put into service
after month and year indicated on label
(label located between terminals) charge
battery for minimum of one hour at 6-10
amps. (See "BATTERY" in Maintenance
section of this manual for charging instruc
tions).

8

INSTALL SEAT

Adjust seat before tightening adjustment
knob.

1. Remove adjustment knob and flat
washer securing seat to cardboard
packing and set aside for assembly of
seat to tractor.

2. Pivot seat upward and remove from
the cardboard packing. Remove the
cardboard packing and discard.

3. Place seat on seat pan so head of
shoulder bolt is positioned over large
slotted hole in pan.

4. Push down on seat to engage shoulder
bolt in slot and pull seat towards rear of

tractor.

5. Pivot seat and pan forward and as
semble adjustment knob and flat
washer loosely. Do not tighten.

6. Lower seat into operating position and
sit in seat.

7. Slide seat until a comfortable position
is reached which allows you to press
clutch/brake pedal all the way down.

8. Get off seat without moving its ad

justed position.

9. Raise seat and tighten adjustment
knob securely.

NOTE: You may now roll or drive your
tractor off the skid. Follow the appropriate
instruction below to remove the tractor
from the skid.

TO ROLL TRACTOR OFF SKID (See
Operation section for location and
function of controls)

1. Press lift lever plunger and raise
attachment lift lever to its highest po
sition.

2. Release parking brake by depressing
clutch/brake pedal.

3. Place gearshift lever in neutral (N)
position.

4. Roll tractor forward off skid.

5. Remove banding holding deflector
shield up against tractor.

TO DRIVE TRACTOR OFF SKID (See
Operation section for location and
function of controls)

^WARNING: Before starting, read, un

derstand and follow all instructions in the
Operation section of this manual. Be sure
tractor is in a well-ventilated area. Be sure
the area in front of tractor is clear of other
people and objects.

1. Be sure all the above assembly steps
have been completed.

2. Check engine oil level and fill fuel tank
with gasoline.

3. Sit on seat in operating position,
depress clutch/brake pedal and set the
parking brake.

4. Place gear shift lever in neutral (N)
position.

5. Press lift lever plunger and raise
attachment lift lever to its highest posi

tion.

6. Start the engine. After engine has
started, move throttle control to idle
position.

7. Depress clutch/brake pedal into full
"BRAKE" position and hold. Move

gearshift lever to 1 st gear.

8. Slowly release clutch/brake pedal and
slowly drive tractor off skid.

9. Apply brake to stop tractor, set park
ing brake and place gearshift lever in
neutral position.

10. Turn ignition key to "STOP" position.

Continue with the instructions that follow.

9

INSTALL MULCHER PLATE (If previously removed)

1. Raise and hold deflector shield in
upright position.

2. Place front of mulcher piate over front
of mower deck opening and slide into
place, as shown.

3. Hook front latch into hole on front of
mower deck.

4. Hook rear latch into hole on back of
mower deck.

ACAUTION; Do not remove deflector
shield from mower.

TO CONVERT TO BAGGING OR

DISCHARGING

Simply remove mulcher plate and store in
a safe place. Your mower is now ready for
discharging or installation of optional grass
catcher accessory.

NOTE: It is not necessary to change

blades. The mulcher blades are designed
for discharging and bagging also.

CHECK TIRE PRESSURE

The tires on your tractor were overin
flated at the factory for shipping purposes.
Correct tire pressure is important for best
cutting performance.

• Reduce tire pressure to PSI shown in

“PRODUCT SPECIFICATIONS” section
of this manual.

CHECK DECK LEVELNESS

For best cutting results, mower hous

ing should be properly leveled. See “TO

LEVEL MOWER HOUSING” in the Service
and Adjustments section of this manual.

CHECK FOR PROPER POSITION OF ALL BELTS

See the figures that are shown for replac
ing motion and mower blade drive belts
in the Service and Adjustments section

of this manual. Verify that the belts are

routed correctly.

CHECK BRAKE SYSTEM

After you learn how to operate your trac
tor, check to see that the brake is properly
adjusted. See “TO ADJUST BRAKE” in
the Service and Adjustments section of
this manual.

^CHECKLIST

Before you operate and enjoy your new
tractor, we wish to assure that you receive
the best performance and satisfaction
from this Quality Product.

Please review the following checklist:
/ All assembly instructions have been

completed.
/ No remaining loose parts in carton.
/ Battery is properly prepared and

charged. {Minimum 1 hour at 6 amps).
/ Seat is adjusted comfortably and tight

ened securely.
/ All tires are properly inflated. (For ship

ping purposes, the tires were overin

flated at the factory).
/ Be sure mower deck is properly leveled

side-to-side/front-to-rear for best cutting

results. (Tires must be properly inflated

for leveling).
/ Check mower and drive belts. Be sure

they are routed properly around pulleys

and inside all belt keepers.
/ Check wiring. See that ail connections

are still secure and wires are properly

clamped.
While learning how to use your tractor, pay
extra attention to the following important

items;

/ Engine oil is at proper level.
/ Fuel tank is filled with fresh, clean, regu

lar unleaded gasoline.
/ Become familiar with all controls - their

location and function. Operate them

before you start the engine.
/ Be sure brake system is in safe oper

ating condition.

10

These symbols may appear on your tractor or in literature supplied with the product.

Learn and understand their meaning.

R

REVERSE

ENGINE OFF LIGHTS ON ENGINE ON ENGINE START PARKING BRAKE PARKING BRAKE PARKING BRAKE

IGINE OI

Ô1

)VER TEMI

LiGHT

ATTACHMENT ATTACHMENT

CLUTCH ENGAGED CLUTCH DISENGAGED DANGER, KEEP HANDS KEEP AREA CLEAR SLOPE HAZARDS

FREE WHEEL

(Automatic Modela only)

N

NEUTRAL HIGH

EUTR

ai

.IGHTS OI

li ‘fir-

H L \\\ ’^

LOW CHOKE FAST SLOW fGI

© 0 © c©

LOCKED UNLOCKED

$

AND FEET AWAY (SEE SAFETY RULES SECTION)

DANGER indicates a hazard which, if not avoided,

will result in death or serious injury.
WARNING indicates a hazard which, if not avoided,

could result in death or serious injury.
CAUTION indicates a hazard which, if not avoided,

might result in minor or moderate injury.

j;

5Í

EGNITiON

A

Failure to follow instructions
could result in serious injury or
death. The safety alert symbol
is used to identify safety inform
ation about hazards which can
result in death, serious injury
and/or property damage.

CAUTION when used without the alert symbol,

indicates a situation that could result in damage

to the tractor and/or engine.

HOT SURFACES indicates a hazard which,

.i№№. avoided, could result in death, serious injury

■

------ and/or property damage.

'f, FIRE indicates a hazard which, if not avoided,

could result in death, serious injury and/or
property damage.

11

KNOW YOUR TRACTOR

READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR
TRACTOR

Compare the illustrations with your tractor to famiiiarize yourseif with the locations of
various controls and adjustments. Save this manual for future reference.

Our tractors conform to the safety standards of the

American National Standards institute.

AMMETER - indicates charging (+) or
discharging (-) of battery.
ATTACHMENT CLUTCH LEVER - Used
to engage the mower blades, or other at
tachments mounted to your tractor.
ATTACHMENT LIFT LEVER - Used to

raise, lower, and adjust the mower deck or
other attachments mounted to your tractor.
CLUTCH/BRAKE PEDAL - Used for
declutching and braking the tractor and
starting the engine.
GEARSHIFT LEVER - Selects the speed
and direction of tractor.

IGNITION SWITCH - Used for starting and

stopping the engine.

LIFT LEVER PLUNGER - Used to release

attachment lift lever when changing its

position.
LIGHT SWITCH POSITION - Turns the
headlights on and off.
PARKING BRAKE LEVER - Locks clutch/
brake pedal into the brake position.

THROTTLE CONTROL - Used for start

ing and controlling engine speed.
CHOKE CONTROL - Used when starting

a cold engine.

12

FORE$lQHr№BErTiR

THAHHOSIQHr

The operation of any tractor can result in foreign objects thrown into
the eyes, which can result in severe eye damage. Always wear safety
glasses or eye shields while operating your tractor or performing any
adjustments or repairs. We recommend a wide vision safety mask over
spectacles or standard safety glasses.

HOW TO USE YOUR TRACTOR
TO SET PARKING BRAKE

Your tractor is equipped with an operator
presence sensing switch. When engine
is running, any attempt by the operator
to leave the seat without first setting the
parking brake will shut off the engine.

1. Depress clutch/brake pedal all the way
down and hold.

2. Pull parking brake lever up and release
pressure from clutch/brake pedal.

Pedal should remain in brake position.
Make sure parking brake will hold trac

tor secure.

Attachment Clutch Lever
“Engaged” Position

Choke
Control

ThrottI
Contro

CIùtch/
Brake‘s

Pedal

“Disengaged

Position

Ignition Key

“Disengaged”
Position

Parking Brake

“Engaged”

Position

Gearshift

“Brake”
Position

STOPPING

MOWER BLADES -

• To stop mower blades, move attachment

clutch lever to “DISENGAGED” position.

GROUND DRIVE -

• To stop ground drive, depress clutch/

brake pedal all the way down.

• Move gearshift lever to neutral (N)

position.

ENGINE -

• Move throttle control to slow position.

NOTE: Failure to move throttle control
to slow position and allowing engine to
idle before stopping may cause engine to
“backfire”.

• Turn ignition key to “STOP” position and

remove key. Always remove key when
leaving tractor to prevent unauthorized
use.

• Never use choke to stop engine.

IMPORTANT: Leaving the ignition switch
in any position other than "STOP" will
cause the battery to discharge and go
dead.
NOTE: Under certain conditions when
tractor is standing idle with the engine

running, hot engine exhaust gases may
cause “browning” of grass. To eliminate
this possibility, always stop engine when
stopping tractor on grass areas.

^CAUTION: Always stop tractor com

pletely, as described above, before leaving
the operator's position.

TO USE THROTTLE CONTROL

Always operate engine at full throttle.

• Operating engine at less than full

throttle reduces the battery charging

rate.

• Full throttle offers the best bagging and

mower performance.

TO USE CHOKE CONTROL

Use choke control whenever you are start
ing a cold engine. Do not use to start a
warm engine.

• To engage choke control, pull knob out.

Slowly push knob in to disengage.

TO MOVE FORWARD AND BACKWARD

The direction and speed of movement is
controlled by the gearshift lever.

1. Start tractor with clutch/brake pedal de
pressed and gearshift lever in neutral
(N) position.

2. Move gearshift lever to desired po
sition.

3. Slowly release clutch/brake peda! to
start movement.

IMPORTANT: Bring tractor to a complete
stop before shifting or changing gears.

Failure to do so will shorten the useful life

of your transaxle.

TO ADJUST MOWER CUTTING HEIGHT

The position of the attachment lift lever
determines the cutting height.

• Grasp lift lever.

• Press plunger with thumb and move

lever to desired position.

13

The cutting height range is approxi

mately 1-1/2 to 4". The heights are mea
sured from the ground to the blade tip with
the engine not running. These heights
are approximate and may vary depending

upon soil conditions, height of grass and
types of grass being mowed.

• The average lawn should be cut to ap

proximately 2-1/2 inches during the cool
season and to over 3 inches during hot
months. For healthier and better looking
lawns, mow often and after moderate
growth.

• For best cutting performance, grass over

6 inches in height should be mowed
twice. Make the first cut relatively high;
the second to desired height.

TO ADJUST GAUGE WHEELS

Gauge wheels are properly adjusted
when they are slightly off the ground when

mower is at the desired cutting height in
operating position. Gauge wheels then

keep the deck in proper position to help

prevent scalping in most terrain conditions.

NOTE: Adjust gauge wheels with tractor
on a flat level surface.

1.

Adjust mower to desired cutting height
(See “TO ADJUST MOWER CUTTING
HEIGHT” in this section of manual).

2.

With mower in desired height of cut
position, gauge wheels should be assem
bled so they are slightly off the ground.

Install gauge wheel in appropriate hole

with shoulder bolt, 3/8 washer, and 3/8-

16 locknut and tighten securely.

Repeat for opposite side, installing

3.

gauge wheel in same adjustment hole.

Gauge Wheel
Mounting

Bracket

3/8-16

Locknut

3/8 Washer

Gauge Wheel

Shoulder

-olt

TO OPERATE MOWER

Your tractor is equipped with an operator

presence sensing switch. Any attempt

by the operator to leave the seat with the
engine running and the attachment clutch
engaged will shut off the engine. You must

remain fully and centrally positioned in the
seat to prevent the engine from hesitating
or cutting off when operating your equip

ment on rough, rolling terrain or hills.

1. Select desired height of cut.

2. Start mower blades by engaging at
tachment clutch control.

TO STOP MOWER BLADES ­disengage attachment clutch control.

ACAUTION: Do not operate the mower
without either the entire grass catcher,
on mowers so equipped, or the deflector
shield in place.

TO OPERATE ON HILLS
^WARNING: Do not drive up or down

hills with slopes greater than 15° and do
not drive across any slope. Use the slope

guide at the back of this manual.

Choose the slowest speed before start
ing up or down hills.
Avoid stopping or changing speed on
hills.

If slowing is necessary, move throttle

control lever to slower position.

If stopping is absolutely necessary, push
clutch/brake pedal quickly to brake posi
tion and engage parking brake.
Move gearshift lever to 1st gear. Be
sure you have allowed room for tractor
to roll slightly as you restart movement.
To restart movement, slowly release
parking brake and clutch/brake pedal.
Make all turns slowly.

TO TRANSPORT

Raise attachment lift to highest position
with attachment lift control.
When pushing or towing your tractor,
be sure gearshift lever is in neutral (N)
position.

Do not push or tow tractor at more than
five (5) MPH.

NOTE; To protect hood from damage when
transporting your tractor on a truck or a
trailer, be sure hood is closed and secured
to tractor. Use an appropriate means of
tying hood to tractor (rope, cord, etc.).

14

TOWING CARTS AND OTHER ATTACH
MENTS

Tow only the attachments that are recom
mended by and comply with specifications
of the manufacturer of your tractor. Use
common sense when towing. Too heavy
of a load, while on a slope, is dangerous.
Tires can iose traction with the ground and
cause you to lose control of your tractor.

ENGINE

CHECK ENGINE OIL LEVEL

The engine in your tractor has been
shipped, from the factory, already filled
with summer weight oil.

1. Check engine oil with tractor on level
ground.

2. Remove oil fill cap/dipstick and wipe
clean, reinsert the dipstick and screw
cap tight, wait for a few seconds, re

move and read oil level. If necessary,

add oil until TULL’ mark on dipstick is

reached. Do not overfill.

• For cold weather operation you should

change oil for easier starting (See the
oil viscosity chart in the Maintenance
section of this manual).

• To change engine oil, see the Mainte

nance section in this manual.

ADD GASOLINE

• Fill fuel tank to bottom of filler neck. Do

not overfill. Use fresh, clean, regular
unleaded gasoline with a minimum of
87 octane. (Use of leaded gasoline will
increase carbon and lead oxide deposits
and reduce valve life). Do not mix oil
with gasoline. Purchase fuel in quan
tities that can be used within 30 days to
assure fuel freshness.

^CAUTION: Wipe off any spilled oil or

fuel. Do not store, spill or use gasoline
near an open flame.
IMPORTANT: When operating in temper
atures below32°F(0°C), use fresh, clean
winter grade gasoline to help insure good
cold weather starting.
CAUTION; Alcohol blended fuels (called
gasohol or using ethanol or methanol) can
attract moisture which leads to separa
tion and formation of acids during storage.

Acidic gas can damage the fuel system
of an engine while in storage. To avoid
engine problems, the fuel system should
be emptied before storage of 30 days
or longer. Drain the gas tank, start the
engine and let it run until the fuel lines
and carburetor are empty. Use fresh fuel
next season. See Storage Instructions for
additional information. Never use engine
or carburetor cleaner products in the fuel
tank or permanent damage may occur.

TO START ENGINE

When starting the engine for the first time
or if the engine has run out of fuel, it will
take extra cranking time to move fuel from
the tank to the engine.

1. Sit on seat in operating position,
depress clutch/brake pedal and set

parking brake.

2. Place gear shift lever in neutral (N)
position.

3. Move attachment clutch to disengaged
position.

4. Move throttle control to fast position

5. Pull choke control out for a cold engine
start attempt. For a warm engine start

attempt the choke control may not be
needed.

NOTE: Before starting, read the warm and
cold starting procedures below.

6. Insert key into ignition and turn key
clockwise to start position and release
key as soon as engine starts. Do
not run starter continuously for more

than fifteen seconds per minute. If the

engine does not start after several
attempts, push choke control in, wait
a few minutes and try again. If engine
still does not start, pul! the choke con

trol out and retry.
WARM WEATHER STARTING (50° F and
above)

7. When engine starts, slowly push choke

control in until the engine begins to
run smoothly. If the engine starts to
run roughly, pul! the choke control out
slightly for a few seconds and then
continue to push the control in slowly.

• The attachments and ground drive can

now be used. If the engine does not
accept the load, restart the engine and
allow it to warm up for one minute using
the choke as described above.

15

COLD WEATHER STARTING (50° F and

below)

7. When engine starts, slowly push choke
control in until the engine begins to run
smoothly. Continue to push the choke
control in small steps allowing the en
gine to accept small changes in speed
and load, until the choke control is fully
in. If the engine starts to run roughly,
pull the choke control out slightly for a
few seconds and then continue to push
the control in slowly. This may require
an engine warm-up period from several
seconds to several minutes, depending
on the temperature.

• The attachments can be used during the

engine warm-up period and may require
the choke control be pulled out slightly.

NOTE: If at a high altitude (above 3000 feet)
or in cold temperatures (below 32 F) the
carburetor fuel mixture may need to be ad
justed for best engine performance (see “TO
ADJUST CARBURETOR” in the Service and
Adjustments section of this manual).

MOWING TIPS

• Mower should be properly leveled for

best mowing performance. See “TO
LEVEL MOWER HOUSING” in the
Service and Adjustments section of this
manual.

• The left hand side of mower should be

used for trimming.

• Drive so that clippings are discharged

onto the area that has already been
cut. Have the cut area to the right of
the tractor. This will result in a more
even distribution of clippings and more
uniform cutting.

• When mowing large areas, start by

turning to the right so that clippings will
discharge away from shrubs, fences,
driveways, etc. After one or two rounds,
mow in the opposite direction making
left hand turns until finished .

• Do not mow grass when it is wet.
Wet grass will plug mower and leave
undesirable clumps. Allow grass to dry
before mowing.

• Always operate engine at full throttle
when mowing to assure better mowing

performance and proper discharge of
material. Regulate ground speed by
selecting a low enough gear to give the
mower cutting performance as well as
the quality of cut desired.

• When operating attachments, select a
ground speed that will suit the terrain
and give best performance of the at
tachment being used.

MULCHING MOWING TIPS

IMPORTANT: For best performance, keep
mower housing free of built-up grass and

trash. Clean after each use.

• The special mulching blade will recut
the grass dippings many times and

reduce them in size so that as they fall
onto the lawn they will disperse into
the grass and not be noticed. Also, the
mulched grass will biodegrade quickly
to provide nutrients for the lawn. Always
mulch with your highest engine (blade)
speed as this will provide the best recut
ting action of the blades.

• Avoid cutting your lawn when it is wet.
Wet grass tends to form clumps and
interferes with the mulching action. The
best time to mow your lawn is the early
afternoon. At this time the grass has
dried, the newly cut area will not be
exposed to direct sunlight.

• For best results, adjust the mower cutting
height so that the mower cuts off only
the top one-third of the grass blades. For
extremely heavy grass, reduce your width
of cut on each pass and mow slowly.

MAX 1/3

If grass is extremely tall, It should be
mowed twice to reduce load and pos
sible fire hazard from dried clippings.
Make first cut relatively high; the second
to the desired height.

Certain types of grass and grass
conditions may require that an area be
mulched a second time to completely
hide the clippings. When doing a sec
ond cut, mow across (perpendicular) to
the first cut path.
Change your cutting pattern from week
to week. Mow north to south one week
then change to east to west the next
week. This will help prevent matting and
graining of the lawn.

16

MAINTENANCE SCHEDULE

FILL IN DATES
AS YOU COMPLETE
REGULAR SERVICE

Check Brake Operation
Check Tire Pressure

Check Operator Presence and
Interlock Systems

Check for Loose Fasteners
Sharpen/Replace Mower Blades
Lubrication Chart
Check Battery LeveS

Clean Battery and Terminals
Check Transaxle Cooling
Check V-Belts

Check Engine Oil Level
Change Engine OH (with oil filter)

Change Engine Oil (without oil filter)
Clean Aif Fitter

Clean Air Screen
Inspect Muffler/Spark Arrester
Replace Oil Filter (If equipped)
Clean Engine Cooling Fins
Replace Spark Plug
Replace Air Filter Paper Cartridge
Replace Fuel Filter

1 “ Change more often when operating under a heavy load or

in Ngh ambient temperatures.

2 “ Service more often when operating in dirty or dusty conditions.

✓ ✓
✓

✓
✓

✓

✓

✓ 3

✓ ✓

✓ ✓
✓

✓

*^1,2 ✓

✓ 1,2 ✓

✓ 2

✓

3 " Replace blades more often when mowing in sandy soil.
4 " Not required if equipped with maintenancedree battery.
5 - Tighten front axle pivot bolt to 35 ft.-lbs. maximum.

Do not overtighten.

✓ s

✓

fc<<,2
✓ 2
✓ ✓

✓ 2

✓

GENERAL RECOMMENDATIONS

The warranty on this tractor does not
cover items that have been subjected to
operator abuse or negligence. To receive
full value from the warranty, operator
must maintain tractor as instructed in this
manual.
Some adjustments will need to be made
periodically to properly maintain your
tractor.
At least once a season, check to see if
you should make any of the adjustments
described in the Service and Adjustments
section of this manual.

• At least once a year you should replace
the spark plug, clean or replace air filter,
and check blades and belts for wear.
A new spark plug and clean air filter
assure proper air-fuel mixture and help
your engine run better and last longer.

BEFORE EAOH USE

1. Check engine oil level.

2. Check brake operation.

3. Check tire pressure.

4. Check operator presence and

interlock systems for proper operation.

5. Check for loose fasteners.

LUBRICATION CHART

®SAE 30 or 10w30 Motor Oil
©General Purpose Grease
©Refer to Maintenance “ENGINE” Section

IMPORTANT: Do not oil or grease the

pivot points which have special nylon
bearings. Viscous lubricants will attract
dust and dirt that wili shorten the life of
the self-lubricating bearings. If you fee!
they must be lubricated, use only a dry,
powdered graphite type lubricant sparingly.

17

TRACTOR

Always observe safety rules when per
forming any maintenance.

BRAKE OPERATION

If tractor requires more than six (6) feet
stopping distance at high speed in highest
gear, then brake must be adjusted. (See
“TO ADJUST BRAKE” in the Service and
Adjustments section of this manual).

TIRES

• Maintain proper air pressure in all tires

(See “PRODUCT SPECIFICATIONS”
section of this manual).

• Keep tires free of gasoline, oil, or insect

control chemicals which can harm rub
ber.

• Avoid stumps, stones, deep ruts, sharp

objects and other hazards that may
cause tire damage.

NOTE: To seal tire punctures and prevent
flat tires due to slow leaks, tire sealant

may be purchased from your local parts
dealer. Tire sealant also prevents tire dry

rot and corrosion.

OPERATOR PRESENCE SYSTEM

Be sure operator presence and interlock
systems are working properly. If your trac
tor does not function as described, repair
the problem immediately.

• The engine should not start unless the

clutch/brake pedal is fully depressed
and attachement clutch control is in the
disengaged position.

• When the engine is running, any at

tempt by the operator to leave the seat
without first setting the parking brake
should shut off the engine.

• When the engine is running and the

attachment clutch is engaged, any at
tempt by the operator to leave the seat
should shut off the engine.

• The attachment dutch should never op

erate unless the operator is in the seat.

BLADE CARE

For best results mower blades must be

kept sharp. Replace bent or damaged

blades.

IMPORTANT: To ensure proper assembly,
center hole in blade must align with star
on mandrel assembly.

4. Reassemble blade bolt, lock washer

and flat washer in exact order as
shown.

5. Tighten bolt securely (27-35 Ft. Lbs.

torque).
IMPORTANT: Blade bolt is heat treated.
If bolt needs replacing, replace only with

approve bolt shown in the Repair Parts.

Trailing

Edge Up

Fiat Washer.

Lock Washer

.^Biade

Mandrel Assembly

Blade Bolt

TO SHARPEN BLADE

NOTE: We do not recommend sharp

ening blade - but if you do, be sure the

blade is balanced.

Care should be taken to keep the blade

balanced. An unbalanced blade will cause

excessive vibration and eventual damage
to mower and engine.

• The blade can be sharpened with a file
or on a grinding wheel. Do not attempt
to sharpen while on the mower.

• To check blade balance, you will need a
5/8” diameter steel bolt, pin, or a cone
balancer. (When using a cone balancer,
follow the instructions supplied with
balancer.)

NOTE: Do not use a nail for balancing
blade. The lobes of the center hole may

appear to be centered, but are not.

• Slide blade on to an unthreaded portion
of the steel bolt or pin and hold the
bolt or pin parallel with the ground. If
blade is balanced, it should remain in a
horizontal position. If either end of the
blade moves downward, sharpen the
heavy end until the blade is balanced.

BLADE REMOVAL

1. Raise mower to highest position to al
low access to blades.

2. Remove blade bolt, lock washer and
flat washer securing blade.

3. Install new or resharpened blade
with trailing edge up towards deck as
shown.

18

BATTERY

Your tractor has a battery charging system
which is sufficient for normal use. How
ever, periodic charging of the battery with
an automotive charger will extend its life.

• Keep battery and terminals clean.

• Keep battery bolts tight.

• Keep small vent holes open.

• Rechargeât 6-10 amperes for 1 hour.
NOTE: The original equipment battery on
your tractor is maintenance free. Do not
attempt to open or remove caps or covers.
Adding or checking level of electrolyte is
not necessary.

TO CLEAN BATTERY AND TERMINALS
Corrosion and dirt on the battery and

terminals can cause the battery to “leak”
power.

1. Remove terminal guard.

2. Disconnect BLACK battery cable first
then RED battery cable and remove
battery from tractor.

3. Rinse the battery with plain water and
dry.

4. Clean terminals and battery cable ends
with wire brush until bright.

5. Coat terminals with grease or petro

leum jelly.

6. Reinstall battery (See “REPLACING

BATTERY" in the SERVICE AND AD

JUSTMENTS section of this manual).

TRANSAXLE COOLING

Keep transaxle free from build-up of dirt

and chaff which can restrict cooling.

NOTE: Although multi-viscosity oils
(5W30, 10W30 etc.) improve starting in
cold weather, they will result in increased
oil consumption when used above 32°F.
Check your engine oil level more frequent
ly to avoid possible engine damage from

running low on oil.
Change the oil after every 50 hours of op
eration or at least once a year if the tractor
is not used for 50 hours in one year.
Check the crankcase oil level before start
ing the engine and after each eight (8)
hours of operation. Tighten oil fill cap/
dipstick securely each time you check the

oil level.

TO CHANGE ENGINE OIL

Determine temperature range expected
before oil change. All oil must meet API
service classification SF-SJ.

• Be sure tractor is on level surface.

• Oil will drain more freely when warm.

• Catch oil in a suitable container.

1. Remove oil fill cap/dipstick. Be careful
not to allow dirt to enter the engine
when changing oil.

2. Remove yellow cap from end of drain
valve and install the drain tube onto the
fitting.

Oil Drain Valve

Closed and
Locked

Position

V^BELTS

Check V-belts for deterioration and wear
after 100 hours of operation and replace
if necessary. The belts are not adjustable.

Replace belts if they begin to slip from

wear.

ENGINE
LUBRICATION

Only use high quality detergent oil rated
with API service classification SF-SJ.

Select the oil’s SAE viscosity grade
according to your expected operating
temperature.

TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE

cii...vi£c...charti...e

Yellow Cap

Drain

Tube

3. Unlock drain valve by pushing inward
slightly and turning counterclockwise.

4. To open, pull out on the drain valve.

5. After oil has drained completely, close
and lock the drain valve by pushing
inward and turning clockwise until the
pin is in the locked position as shown.

6. Remove the drain tube and replace the
cap onto the end of the drain valve.

7. Refill engine with oil through oil fill dip
stick tube. Pour slowly. Do not overfill.
For approximate capacity see “PROD
UCT SPECIFICATiONS” section of this
manual.

19

8. Use gauge on oi! fill cap/dipstick for
checking level. For accurate reading,
tighten dipstick cap securely onto the
tube before removing dipstick. Keep oil
at “FULL’ line on dipstick. Tighten cap
onto the tube securely when finished.

CLEAN AIR SCREEN

Air screen must be kept free of dirt and
chaff to prevent engine damage from

overheating. Clean with a wire brush or
compressed air to remove dirt and stub

born dried gum fibers.

AIR FILTER

Your engine will not run properly using a
dirty air filter. Clean the foam pre-cleaner
after every 25 hours of operation or every
season. Service paper cartridge every

100 hours of operation or every season,

whichever occurs first.

Service air cleaner more often under

dusty conditions.

1. Remove cover.

TO SERVICE PRE-CLEANER

2. Wash it in liquid detergent and water.

3. Squeeze it dry in a clean cloth.

4. Saturate it in engine oil. Wrap it in
clean, absorbent doth and squeeze to
remove excess oil.

NOTE: If very dirty or damaged, replace
pre-cleaner.

TO SERVICE CARTRIDGE

1. Clean cartridge by tapping gently on
flat surface. If very dirty or damaged,
replace cartridge.

2. Reinstall precleaner cartridge, cover
and secure.

IMPORTANT: Petroleum solvents, such
as kerosene, are not to be used to clean
the cartridge. They may cause deterio

ration of the cartridge. Do not oil car
tridge. Do not use pressurized air to clean
or dry cartridge.

CLEAN AIR INTAKE/COOLINO AREAS

To insure proper cooling, make sure the
grass screen, cooling fins, and other exter

nal surfaces of the engine are kept clean

at all times.

Every 100 hours of operation (more often
under extremely dusty, dirty conditions),
remove the blower housing and other cool

ing shrouds. Clean the cooling fins and
external surfaces as necessary. Make sure
the cooling shrouds are reinstalled.

NOTE: Operating the engine with a

blocked grass screen, dirty or plugged
cooling fins, and/or cooling shrouds

removed will cause engine damage due to
overheating.

ENGINE OIL FILTER

Replace the engine oil filter every season
or every other oil change if the tractor is

used more than 100 hours in one year.

MUFFLER

Inspect and replace corroded muffler and
spark arrester (if equipped) as it could cre
ate a fire hazard and/or damage.

SPARK PLUG(S)

Replace spark plug(s) at the beginning
of each mowing season or after every

100 hours of operation, whichever occurs
first. Spark plug type and gap setting are
shown in “PRODUCT SPECIFICATIONS”
section of this manual.

Knobs -

Cover

Foam
Pre-Cleaner

Cartridge

IN-LINE FUEL FILTER

The fuel filter should be replaced once
each season. If fuel filter becomes
dogged, obstructing fuel flow to carbu

retor, replacement is required.

1. With engine cool, remove filter and
plug fuel line sections.

2. Place new fuel filter in position in fuel line
with arrow pointing towards carburetor.

3. Be sure there are no fuel line leaks and
clamps are properly positioned.

4. Immediately wipe up any spilled gaso

line.

Clamp

Fuel Filter

Clamp

20

CLEANING

• Clean engine, battery, seat, finish, etc.
of all foreign matter.

• Keep finished surfaces and wheels free
of all gasoline, oil, etc.

• Protect painted surfaces with auto
motive type wax.

WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SER

A

VICE OR ADJUSTMENTS:

1. Depress clutch/brake pedal fully and set parking brake.

2. Place gearshift lever in neutral (N) position.

3. Place attachment clutch in “DISENGAGED” position.

4. Turn ignition key to “STOP” and remove key.

5. Make sure the blades and all moving parts have completely stopped.

6. Disconnect spark plug wire from spark plug and place wire where it cannot
come in contact with plug.

We do not recommend using a garden
hose or pressure washer to clean your
tractor unless the engine and transmis
sion are covered to keep water out. Water
in engine or transmission will shorten the
useful life of your tractor. Use compressed
air or a leaf blower to remove grass,
leaves and trash from tractor and mower.

TRACTOR

TO REMOVE MOWER

Mower will be easier to remove from the

right side of tractor.

1. Place attachment clutch in “DISEN
GAGED” position.

2. Move attachment lift lever forward to
lower mower to its lowest position.

3. Roll belt off engine pulley.

4. Remove small retainer spring, and
remove clutch spring off pulley bolt.

5. Remove large retainer spring, slide

collar off and push housing guide out
of bracket.

6. Disconnect anti-sway bar from chassis

bracket by removing retainer spring.

7. Disconnect suspension arms from rear

deck brackets by removing retainer
springs.

Smaii Retainer Spring -

Clutch Spring

Small Retainer Spring,

Clutch Spring

8. Disconnect front links from deck by
removing retainer springs.

9. Raise lift lever to raise suspension arms.
Slide mower out from under tractor.

IMPORTANT: If an attachment other than
the mower deck is to be mounted on the
tractor, remove the front links and hook
the clutch spring Into square hole in frame.

TO INSTALL MOWER

1. Raise attachment lift lever to its highest
position.

2. Slide mower under tractor with deflec
tor shield to right side of tractor.

3. Lower lift lever to its lowest position.

4. Connect front links to mower deck and

secure with retainer springs.

5. Connect suspension arms to rear

deck brackets and secure with retainer
springs.

Square Hole

Engine Pulley

Retainer Spring

Anti-Sway Bar —

Collar

Housing
Guide

Large Retainer Spring

Retainer Springs
(Both Sides)

Deflector Shield

6. Connect anti-sway bar to chassis
bracket and secure with retainer spring.

7. Push dutch cable housing guide into
bracket, slide coilar onto guide and
secure with large retainer spring.

8. Place flat washer and clutch spring on
idler pulley bolt and secure with small
retainer spring.

9. Install belt onto engine pulley.

TO LEVEL MOWER HOUSING

Adjust the mower while tractor is parked
on level ground or driveway. Make sure
tires are properly inflated (See “PROD

UCT SPECIFICATIONS” section of this
manual). If tires are over or underinflated,
you will not properly adjust your mower.

SiDE-TO-SIDE ADJUSTMENT

• Raise mower to its highest position.

• At the midpoint of both sides of mower,
measure height from bottom edge of
mower to ground. Distance “A” on both
sides of mower should be the same or
within 1/4" of each other.

• If adjustment is necessary, make adjust
ment on one side of mower only.

• To raise one side of mower, tighten lift
link adjustment nut on that side.

• To lower one side of mower, loosen lift
link adjustment nut on that side.

NOTE; Each full turn of adjustment nut

will change mower height about 1/8".

• Recheck measurements after adjusting.

Check adjustment on right side of trac
tor. Measure distance “D” directly in front
and behind the mandrel at bottom edge of

mower housing as shown.

• Before making any necessary adjust
ments, check that both front links are
equal in length.

• If links are not equal in length, adjust
one link to same length as other link.

• To lower front of mower loosen nut “E”
on both front links an equal number of
turns.

• When distance “D” is 1/8" to 1/2"
lower at front than rear, tighten nuts “F”
against trunnion on both front links.

• To raise front of mower, loosen nut “F”
from trunnion on both front links. Tighten
nut “E” on both front links an equal num
ber of turns. The two front links must

remain equal in length.

• When distance “D” is 1/8" to 1/2" lower
at front than rear, tighten nut “F” against
trunnion on both front links.

• Recheck side-to-side adjustment.

Mandrel

Both Front Links Should be Equal in Length

Bottom edge
of mower to
ground

Lift Link

Adjustment Nut

do

Bottom edge of

er to ground

Suspension Arm

FRONT-TO-BACK ADJUSTMENT
IMPORTANT: Deck must be level side-to

side, if the following front-to-back adjust

ment is necessary, be sure to adjust both
front links equally so mower will stay level
side-to-side.
To obtain the best cutting results, the

mower housing should be adjusted so
that the front is approximately 1/8" to 1/2"

lower than the rear when the mower is in

its highest position.

Nut “F”

Trunnion

Front Links

Nut “E”

TO REPLACE MOWER BLADE DRIVE

BELT

The mower blade drive belt may be re

placed without tools. Park the tractor on
level surface. Engage parking brake.

BELT REMOVAL -

1. Remove mower from tractor (See “TO
REMOVE MOWER” in this section of
manual).

22

2. Work belt off both mandrel pulleys and
idler pulleys.

3. Pul! belt away from mower.

BELT INSTALLATION -

1. Work belt around both mandrel pulleys
and idler pulleys

2.

Make sure belt is in all pulley grooves

and inside all belt guides.

Install mower (See “To Install Mower” in

3.
this section of this manual).

TO CHECK AND ADJUST BRAKE

Your tractor is equipped with an adjustable
brake system which is mounted on the

right side of the transaxle.

If tractor requires more than five (5) feet to
stop at highest speed in highest gear on a
level, dry concrete or paved surface, then
brake must be checked and adjusted.

TO CHECK BRAKE

1. Park tractor on a level, dry concrete or
paved surface, depress clutch/brake
pedal all the way down and engage
parking brake.

2.

Place gear shift lever in neutral (N)

position.

The rear wheels must lock and skid when
you try to manually push the tractor forward.

If the rear wheels rotate, the brake needs to

be adjusted or the pads need to be replaced.
TO ADJUST BRAKE

1. Depress clutch/brake pedal all the way
down and engage parking brake.

2. Measure distance between brake oper
ating arm and nut “A” on brake rod.

3. If distance is other than 1-1/2", loosen

jam nut and turn nut “A” until distance

becomes 1-1/2". Retighten jam nut
against nut “A”.

Road test tractor for proper stopping
distance as stated above. Readjust
if necessary. If stopping distance is
still greater than five (5) feet in highest
gear, further maintenance is neces
sary. Replace brake pads or contact a
Sears or other qualified service center.

With parking brake “Engaged”

TO REPLACE MOTION DRIVE BELT

Park the tractor on level surface. Engage
parking brake. For assistance, there is a
belt installation guide decal on bottom side
of left footrest.

BELT REMOVAL -

1. Remove mower (See “TO REMOVE
MOWER” in this section of manual).

NOTE: Observe entire motion drive belt
and position of all belt guides and keepers.

2. Remove belt from stationary idler and
clutching idler.

3. Remove belt downward from around
engine pulley.

4. Pull belt slack toward rear of tractor.
Remove belt upwards from transaxle
pulley by deflecting belt keepers.

5. Remove belt from center span keeper
and pull belt away from tractor.

BELT INSTALLATION -

1. Carefully work new belt down between
transaxie belt keepers and onto the

input pulley

2. Slide belt into the center span keeper.

3. Pull belt toward front of tractor and roll
around the top groove of engine pulley.

4. Install belt through stationary idler and
clutching idler.

5. Make sure belt is in all pulley grooves
and inside all belt guides and keepers.

6. Install mower (See “TO INSTALL
MOWER” in this section of manual).

23

TRAL ADJUSTfWENT

The transaxle should be in neutral when
the gear shift lever is in neutral (N) (lock
gate) position. The adjustment is preset
at the factory; however, if adjustment is

needed, proceed as follows:

1. Make sure transaxle is in neutral (N).
NOTE: When the tractor rear wheels move

freely, the transaxle is in neutral.

2. Loosen adjustment bolt in front of the
right rear wheel.
Position the gear shift lever in the neu

3.

tral (N) position.

4.

Tighten adjustment bolt securely.

NOTE: If additional clearance is needed
to get to adjustment bolt, move mower
deck height to the lowest position.

Gearshift Lever

Neutral Lock Gate

TO ADJUST STEERING WHEEL ALIGN

MENT

If steering wheel crossbars are not
horizontal (left to right) when wheels are
positioned straight forward, remove steer
ing wheel and reassemble with crossbars
horizontal. Tighten securely.
FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not
adjustable on your tractor. If damage has
occurred to affect the front wheel toe-in or
camber, contact a Sears or other qualified
service center.

TO REMOVE WHEEL FOR REPAIRS

1. Block up axle securely.

2. Remove axle cover, retaining ring and
washers to allow wheel removal (rear
wheels have a square key - Do not

lose).

3. Repair tire and reassemble.

NOTE: On rear wheels only: align
grooves in rear wheel hub and axle. Insert
square key.

4. Replace washers and snap retaining

ring securely in axle groove.

5. Replace axle cover.

NOTE: To sea! tire punctures and prevent
flat tires due to slow leaks, purchase and

use tire sealant from Sears. Tire sealant
also prevents tire dry rot and corrosion.

Washers

Retaining
Ring

Axle
Cover

Adjustment Bolt

Square Key

(Rear Wheel Only)

24

TO START ENGINE WITH A WEAK BAT­T*ERY

^WARNING: Lead-acid batteries gen

erate explosive gases. Keep sparks, flame
and smoking materials away from bat
teries. Always wear eye protection when
around batteries.

if your battery is too weak to start the
engine, it should be recharged. (See "BAT
TERY" in the MAINTENANCE section of
this manual).

If “jumper cables” are used for emergency
starting, follow this procedure:
IMPORTANT; Your tractor is equipped
with a 12 volt system. The other vehicle
must also be a 12 volt system. Do not use
your tractor battery to start other vehicles.

TO ATTACH JUMPER CABLES -

1. Connect one end of the RED cable
to the POSITIVE {+) terminal of each
battery(A-B), taking care not to short
against tractor chassis.

2.

Connect one end of the BLACK cable
to the NEGATIVE {-) terminal (C) of
fully charged battery.
Connect the other end of the BLACK

3.
cable (D) to good chassis ground,
away from fuel tank and battery.

TO REMOVE CABLES, REVERSE
ORDER -

1. BLACK cable first from chassis and
then from the fully charged battery.

2. RED cable last from both batteries.

Weak or Dead
Battery

Fully Charged
Battery

REPLACING BATTERY

^WARNING: Do not short battery

terminals by allowing a wrench or any
other object to contact both terminals at
the same time. Before connecting battery,

remove metal bracelets, wristwatch bands,
rings, etc.

Positive terminal must be connected
first to prevent sparking from accidental
grounding.

1.

Lift hood to raised position.

2.

Remove terminal guard.

3.

Disconnect BLACK battery cable

then RED battery cable and carefully

remove battery from tractor.

4.

Install new battery with terminals in

same position as old battery.

5.

Reinstall terminal guard.
First connect RED battery cable to

6.

positive (+) battery terminal with hex
bolt and keps nut as shown. Tighten
securely.
Connect BLACK grounding cable to
negative (-} battery terminal with re
maining hex bolt and keps nut. Tighten
securely

8.

Close terminal access doors.

9.

Close hood.

Hex Bolt

ositive
(Red)
Cable

Terminal
Access

Door

Terminal

Guard

Keps Nut

Negative
(Black)
Cable

TO REPLACE HEADLIGHT BULB

1. Raise hood.

2. Pull bulb holder out of the hole in the
backside of the grill.

3. Replace bulb in holder and push bulb
holder securely back into the hole in

the backside of the grill.

4. Close hood.

INTERLOCKS AND RELAYS

Loose or damaged wiring may cause
your tractor to run poorly, stop running, or
prevent it from starting.

• Check wiring. See electrical wiring

diagram in the Repair Parts section.

TO REPLACE FUSE

Replace with 20 amp automotive-type
plug-in fuse. The fuse holder is located
behind the dash.

25

TO REMOVE HOOD AND GRILL AS

SEMBLY

1.

Raise hood.

2.

Unsnap headlight wire connector.
Stand in front of tractor. Grasp hood at

3.
sides, tilt toward engine and lift off of

tractor.

4.

When repiacing hood, be sure to re
connect the headlight wire connector.

ENGINE

Maintenance, repair, or replacement of
the emission control devices and systems,
which are being done at the customers ex

pense, may be performed by any non-road
engine repair establishment or individual.
Warranty repairs must be performed by an
authorized engine manufacturer's service
outlet.

TO ADJUST THROTTLE CONTROL

CABLE

The throttle control has been preset at the
factory and adjustment should not be nec
essary. Check adjustment as described

below before loosening cable. If adjust

ment is necessary, proceed as follows:

1. With engine not running, move throttle
control lever to fast position.

2. Check that swivel is against stop. If it is
not, loosen cable clamp screw and pull
cable back until swivel is against stop.

Tighten cable clamp screw securely.

TO ADJUST CHOKE CONTROL
The choke control has been preset at the

factory and adjustment should not be nec
essary. Check adjustment as described

below before loosening cable. If adjust
ment is necessary, proceed as follows:

1. With engine not running, move choke
control (located on dash panel) to full
choke position.

2. Loosen knob and remove cover as
sembly from air cleaner.

3. Choke should be closed. If it is not,

loosen casing clamp screw and move

choke cable until choke is completely
closed. Tighten casing damp screw
securely.

4. Replace air cleaner cover assembly
and tighten knob.

TO ADJUST CARBURETOR

Your carburetor is not adjustable. If your
engine does not operate properly due to
suspected carburetor problems, take your
tractor to an authorized service center for

repair and/or adjustment.
High speed stop is factory adjusted. Do
not adjust - damage may result.

IMPORTANT: Never tamper with the
engine governor, which is factory set
for proper engine speed. Overspeed

ing the engine above the factory high
speed setting can be dangerous, if you
think the engine-governed high speed

needs adjusting, contact a Sears or other
qualified service center,, which has proper
equipment and experience to make any

necessary adjustments.

26

Immediately prepare your tractor for stor
age at the end of the season or if the trac
tor will not be used for 30 days or more.

AcauTION: Never store the tractor

with gasoline in the tank inside a building
where fumes may reach an open flame
or spark. Allow the engine to cool before
storing in any enclosure.

TRACTOR

Remove mower from tractor for winter
storage. When mower is to be stored for a
period of time, dean it thoroughly, remove
all dirt, grease, leaves, etc. Store in a

clean, dry area.

1. Clean entire tractor (See “CLEANING”
in the Maintenance section of this
manual).

2. Inspect and replace belts, if necessary
(See belt replacement instructions in

the Service and Adjustments section of
this manual).

3. Lubricate as shown in the Maintenance

section of this manual.

4. Be sure that all nuts, bolts and screws

are securely fastened. Inspect moving
parts for damage, breakage and wear.

Replace if necessary.

5. Touch up ali rusted or chipped paint

surfaces; sand lightly before painting.

BATTERY

• Fully charge the battery for storage.

• After a period of time in storage, battery

may require recharging.

• To help prevent corrosion and power

leakage during long periods of storage,
battery cables should be disconnected
and battery cleaned thoroughly (see “TO
CLEAN BATTERY AND TERMINALS” in
the Maintenance section of this manual).

• After cleaning, leave cables discon

nected and place cables where they
cannot come in contact with battery
terminals.

• If battery is removed from tractor for

storage, do not store battery directly on
concrete or damp surfaces.

ENGINE

FUEL SYSTEM

IMPORTANT; It is important to prevent

gum deposits from forming in essential
fuel system parts such as carburetor, fuel
hose, or tank during storage. Also, alcohol

blended fuels (called gasohol or using
ethanol or methanol) can attract moisture
which leads to separation and formation of
acids during storage. Acidic gas can dam
age the fuel system of an engine while in
storage.

• Empty the fuel tank by starting the en
gine and letting it run until the fuel lines
and carburetor are empty.

• Never use engine or carburetor cleaner
products in the fuel tank or permanent
damage may occur.

• Use fresh fuel next season.

NOTE: Fuel stabilizer is an acceptable
alternative in minimizing the formation of
fuel gum deposits during storage. Add
stabilizer to gasoline in fuel tank or stor
age container. Always follow the mix ratio
found on stabilizer container. Run engine
at least 10 minutes after adding stabilizer
to allow the stabilizer to reach the car
buretor. Do not empty the gas tank and
carburetor if using fuel stabilizer.

ENGINE OIL

Drain oil (with engine warm) and replace
with clean engine oil. (See “ENGINE” in
the Maintenance section of this manual).

CYLINDER(S)

1. Remove spark plug(s).

2. Pour one ounce of oil through spark

plug hole(s) into cylinder(s).

3. Turn ignition key to “START” position

for a few seconds to distribute oil.

4. Replace with new spark plug(s).

OTHER

• Do not store gasoline from one season

to another.

• Replace your gasoline can if your can

starts to rust. Rust and/or dirt in your
gasoline will cause problems.

• If possible, store your tractor indoors

and cover it to give protection from dust
and dirt.

• Cover your tractor with a suitable pro

tective cover that does not retain mois
ture. Do not use plastic. Plastic cannot
breathe which allows condensation to

form and will cause your tractor to rust.
IMPORTANT: Never cover tractor while
engine and exhaust areas are still warm.

27

TROUBLESHOOTING CHART:

See appropriate section in manual unless directed to Sears service center

PROBLEM CAUSE CORRECTION

Will not start 1. Out of fuel.

2. Engine not “CHOKED”
properly.

3. Engine flooded.

4. Bad spark plug.

5. Dirty air filter.

6. Dirty fuel filter.

7 Water in fuel.

8. Loose or damaged wiring.

9. Carburetor out of adjustment.

10. Engine valves out of
adjustment.

1. Fill fuel tank.

2. See “TO START ENGINE”
in Operation section.

Wait several minutes
before attempting to start.

Replace spark plug.
Clean/replace air filter.
Replace fuel filter.
Empty fuel tank and carbure

tor, refill tank with fresh gas
oline and replace fuel filter.

8. Check all wiring.

9. See “To Adjust Carburetor”
in Service and Adjustments

section.

10. Contact a Sears or other

qualified service center.

Hard to start

Engine will not
turn over

1. Dirty air filter.

2. Bad spark plug.

3. Weak or dead battery.

4. Dirty fuel filter.

5. Stale or dirty fuel.

6. Loose or damaged wiring.

7. Carburetor out of adjustment.

8. Engine valves out of
adjustment.

1. Clutch/brake pedal not
depressed.

2. Attachment clutch is engaged.

3. Weak or dead battery.

4. Blown fuse.

5. Corroded battery terminals.

6. Loose or damaged wiring.

7. Faulty ignition switch.

8. Faulty solenoid or starter.

9. Faulty operator presence
switch (es).

1. Clean/replace air filter.

2. Replace spark plug.

3. Recharge or replace battery.

4. Replace fuel filter.

5. Empty fuel tank and refill tank
with fresh, clean gasoline.

6. Check all wiring.

7. See “To Adjust Carburetor”

in Service and Adjustments

section.

8. Contact a Sears or other
qualified service center.

1. Depress clutch/brake pedal.

2. Disengage attachment clutch.

3. Recharge or replace battery.

4. Replace fuse.

5. Clean battery terminals.

6. Check all wiring.

7. Check/replace ignition switch.

8. Check/replace solenoid or
starter.

9. Contact a Sears or other
qualified service center.

Engine clicks but
will not start

1. Weak or dead battery.

2. Corroded battery terminals.

3. Loose or damaged wiring.

4. Faulty solenoid or starter.

28

1. Recharge or replace battery.

2. Clean battery terminals.

3. Check all wiring.

4. Check/replace solenoid or
starter.

TROUBLESHOOTING CHART:

See appropriate section in manual unless directed to Sears service center

PROBLEM CAUSE CORRECTION

Loss of power 1. Cutting too much grass/too

fast.

2. Throttle in “CHOKE” position.

3. Build-up of grass, leaves
and trash under mower.

4. Dirty air filter.

5. Low oil level/dirty oil.

6. Faulty spark plug.

7. Dirty fuel filter.

8. Stale or dirty fuel.

9. Water in fuel.

10. Spark plug wire loose.

11. Dirty engine air screen/fins.

12. Dirty/clogged muffler.

13. Loose or damaged wiring.

14. Carburetor out of adjustment,

15. Engine valves out of
adjustment.

1.

Raise cutting height/reduce
speed.
Adjust throttle control.
Clean underside of mower
housing.
Clean/replace air filter.
Check oil level/change oil.
Clean and regap or change
spark plug.
Replace fuel filter.
Empty fuel tank and refill tank
with fresh, clean gasoline.
Empty fuel tank and carbure
tor, refill tank with fresh gas
oline and replace fuel filter.

10. Connect and tighten spark
plug wire.

11. Clean engine air screen/fins.

12. Clean/replace muffler.

13. Check all wiring.

14. See “To Adjust Carburetor”
in Service and Adjustments
section.

15. Contact a Sears or other
qualified service center.

Excessive

vibration

Engine continues

to run when

operator leaves
seat with attach
ment ciutch
engaged

Poor cut - uneven 1. Worn, bent or loose blade.

1. Worn, bent or loose blade.

2. Bent blade mandrel.

3. Loose/damaged part(s).

1. Faulty operator-safety
presence control system.

2. Mower deck not level.

3. Buildup of grass, leaves,
and trash under mower.

4. Bent blade mandrel.

5. Clogged mower deck vent
holes from buildup of grass,
leaves, and trash around
mandrels.

1. Replace blade.
Tighten blade bolt.

2. Contact a Sears or other
qualified service center.

3. Tighten loose part{s).
Replace damaged parts.

1. Check wiring, switches and
connections. If not corrected,
contact Sears or other
qualified service center.

1. Replace blade. Tighten
blade bolt.

2. Level mower deck.

3. Clean underside of mower
housing.

4. Contact a Sears or other
qualified service center.

5. Clean around mandrels to
open vent holes.

29

TROUBLESHOOTING CHART:

See appropriate section in manual unless directed to Sears service center

PROBLEM CAUSE CORRECTION

Mower blades will not rotate

Poor grass

discharge

1. Obstruction in clutch
mechanism.

2. Worn/damaged mower drive
belt.

3. Frozen idler pulley.

4. Frozen blade mandrel.

1. Engine speed too slow.

2. Travel speed too fast.

3. Wet grass.

4. Mower deck not level.

5. Low/uneven tire air pressure.

6. Worn, bent or loose blade.

7. Buildup of grass, leaves and

trash under mower.

8. Mower drive belt worn.

9. Blades improperly installed.

10. Improper blades used.

11. Clogged mower deck vent
holes from buildup of grass,
leaves, and trash around
mandrels.

1. Remove obstruction.

2. Replace mower drive belt.

3. Replace idler pulley.

4. Contact a Sears or other
qualified service center.

1.

Place throttle control in
“FAST" position.

2.

Shift to slower speed.
Allow grass to dry before

3.
mowing.

4.

Level mower deck.
Check tires for proper air

5.
pressure.
Replace/sharpen blade.

6.

Tighten blade bolt.

7.

Clean underside of mower
housing.
Replace mower drive belt.

8.
Reinstall blades sharp edge

9.
down.

10. Replace with blades listed
in this manual.

11. Clean around mandrels to
open vent holes.

Headiight(s) not
working
(if so equipped)

Battery will not

charge

Engine “backfires’
when turning
engine “OFF”

1. Switch is “OFF”.

2. Bu!b(s) or !amp(s) burned out.

3. Faulty light switch.

4. Loose or damaged wiring.

5. Blown fuse.

1. Bad battery cell{s).

2. Poor cable connections.

3. Faulty regulator
(if so equipped).

4. Faulty alternator.

1. Engine throttle control not
set at “SLOW’ position for
30 seconds before stopping
engine.

1. Turn switch “ON".

2. Replace bulb(s) or lamp(s).

3. Check/replace light switch.

4. Check wiring and connections.

5. Replace fuse.

1. Replace battery.

2. Check/clean all connections.

3. Replace regulator.

4. Replace alternator.

1. Move throttle control to
“SLOW” position and allow

to idle for 30 seconds before

stopping engine.

30

SCHEMATIC

TRACTOR - - MODEL NUMBER 917.273770

IGNITION SWITCH

POSITION

HUN/LIGHT B+A1 A2+L

START B + S + A1 NONE

CIRCUIT “MAKE”

OFF M+G+A1 NONE

RUN B+A1 NONE

NOTE

YOUR TRACTOR IS
EOUIPPED WITH A SPECIAL

ALTERNATOR SYSTEM.
THE LIGHTS ARE NOT
CONNECTED TO THE
BATTERY, BUT HAVE THEIR
OWN ELECTRICAL SOURCE.

BECAUSE OF THIS, THE
BRIGHTNESS OF THE LIGHTS
WILL CHANGE WITH ENGINE
SPEED. AT IDLE THE LIGHTS
WILL DIM. AS THE ENGINE IS
SPEEDED UP, THE LIGHTS
WILL BECOME THEIR BRIGHTEST.

WIRING INSULATED CLIPS

NOTE; IF WIRING INSULATED CLIPS WERE REMOVED FOR

SERVICING OF UNIT, THEY SHOULD BE REPLACED TO

PROPERLY SECURE YOUR WIRING.

HEADLIGHTS

NON-REMOVABLE

CONNECTIONS

REMOVABLE

CONNECTIONS

31

rtl

ELECTRICAL

TRACTOR - - MODEL NUMBER 917.273770

22

32

ELECTRICAL

TRACTOR - - MODEL NUMBER 917.273770

KEY

PART

NO.

NO.

1 144927 Battery
2 74760412
8 7603J

145211 Boil, Btr Front 1/4-20 x 7-1/2

10
11

150109

12

145769
16 176138
21

183759
22 4152J
24

4799J
25 146148
26 175158 Fuse
27

73510400 Nut Keps Hex 1/4-20 unc
28 145491 Cable Ground

121305X Switch Seat

29
30 175566
33 140403
40 179720
41

71110408
42

131563 Cover Termina!
43 178861 Soienoid

121433X Ammeter Rectangular 6 Amp

45
52

141940
55 17490508

DESCRIPTION

BoH Hex Hd 1/4-20 unc x 3/4
Case Battery

Holddown Battery Front Mount
Nut, Push Nylon Battery Front 1/4
Switch, interlock Push-in
Harness Light Socket (W/4152j)
Buib Light #1156
Cable Battery
Cable Battery

Switch Ign
Key Molded Craftsman
Harness Ign
Boit BIk. Fin Hex 1/4-20 unc x 1/2

Protection Wire Loop
Screw Thdrol 5/16-18x1/2

NOTE: A!i component dimensions given in U. S.

inches 1 inch = 25.4 mm

33

TRACTOR -- MODEL NUMBER 917.273770

CHASSIS AND ENCLOSURES

34

TRACTOR -

CHASSIS AND ENCLOSURES

KEY

NO.

1
2 176554 Drawbar
5
9 168337X013

10 STD533710 Bolt, Carriage 3/8-16 x 1

11

13 172105X010

14

17

18
20 180679
23
26
28
30 175692X613 Fend/Ftrest
31 139976
37
38 175710 Pivot Bracket Assembly, Rear
39
58
60
64
74 STD541437

114 158112 Keeper Belt Rear Lh Stl P930

142 175702

143 186689

144 175582

145

148 17490620

159 155123X428

166 171875
206 170165
207
208 17670608 Screw Thdroi 3/8-16 x 1/2
209
211 145212 Nut Hex Flange Lock
212
219
258 184245X599
259 184246X599
260 184250X428
261 184258X428

- -

MODEL NUMBER 917.273770

PART
NO.

174619 Chassis
155272 Bumper Hood/Dash

174996
17490608 Screw Thdroi 3/8-16 x 1/2

185682X613 Hood Assembly
184921 Bumper Hood

124028X Bushing
STD541437
184247

17490508
174714

184462 Duct Air Engine
72140606 Bolt Rdhd Sqnk 3/8-16 unc x 3/4
154798

156524

17670508
17000612 Screw Hexwsh Thdr 3/8-16 x 3/4
184248 Insert Lens Reflective

17000512 Screw 5/16-18 X 3/4

5479J

DESCRIPTION

Dash
Panel, Dash, L.H.

Panel, Dash, R.H.

Plate Mig. Battery/Tank
Nut

Grille
Bracket, Fender Support

Screw Thdroi 5/16-18x1 /2
Bracket Pivot Laser Lt

Dash Lower STLT
Nut Crowniock 3/8-16 unc

Plate Reinforcement STLT
Bracket Swaybar Chassis
Bracket Pnt Footrest STLT
Rod Pivot Chassis/Hood
Screw 3/8-16 X 1-1/4
Cupholder Stit Black
Screw Hwhd Hi-Lo #13-16 x 3/4
Bolt Shoulder 5/16-18 TT
Screw Thdroi 5/16-18 x 1/2 Tytt

Lens Laser RH
Lens Laser LH
Cover Lens Laser
Insert Grille Laser
Plug, Button

NOTE: All component dimensions given in U. S.

inches 1 inch = 25.4 mm

35

GROUND DRIVE

TRACTOR -- MODEL NUMBER 917.273770

36

TRACTOR - MODEL NUMBER 917.273770

GROUND DRIVE

KEY

KEY

PART

NO.

NO.

1

2 146682 Spring, Return, Brake

123666X

3
4

12000028
121520X

5

17000512 Screw 5/16-18x3/4

6
8 165866

10 STD561210
11 105701X

74550412 Bolt 1/4-28 UNF W/Patch Gr. 8

13
14

10040400
74490544 Bolt Hex FIghd 5/16-18 Gr. 5 82 165711 Spring, Torsion

15
16 STD541431
18 STD523710

STD541437

19
21 106933X
22 130804
24 STD541237

106888X

25

STD551037 Washer 113

26
27

STD561210
28 175765
29 71673

169592

30
32 STD523107
34

175578 Shaft Assembly, Foot Pedal 158 165589 Bracket Shift Mount

120183X Bearing, Nylon

35

STD551062

36
37

STD571810

179114

38

72110622 Bolt Rdhd. 3/8-16 unc x 2-3/4 Gr. 164

39
41

175556
47

127783 Pulley, Idler, V-Groove, Plastic 168

154407

48

123205X Retainer, Belt

49

72110612 Bolt Carr. Sh 3/8-16 x 1-1/2 Gr. 5 197

50

STD541437

51
52

STD541431

10571OX Link, Clutch 212 145212

53

105709X Spring, Clutch Return

55
56 17060620
57

130801 V-Belt, Ground Drive
59 169691

17120614

61
62

8883R
63

175410

DESCRIPTION

Transaxie (See Breakdown)
Peerless 206-545C 65 STD551143

Pulley, Transaxle 70 134683
Ring, Retainer 74 137057

Strap, Torque 75
Rod Shifter Fender STLT 77 123583X

Pin, Cotter
Washer, Shift Piate

Washer Lock Hvy Helical
Nut Lock Hx W/ins 5/16-18 x Gr.5

Bolt Fin Hex 3/8-16 unc x 1 Gr. 5
Nut 85 150360
Knob 89 158391X428 Console, Shift, STLT
Rod, Brake 90
Nut 96 STD624003
Spring, Brake Rod

Pin
Rod, Parking Brake
Cap, Parking Brake
Bracket, Transaxle 151 19133210
Bolt Hex Hd 5/16-18 unc x 3/4

Washer 21/32 X 1 xl6Ga.
Roll Pin 3/16 x 1"
Pulley, Composite, Flat 163

5 165 165623 Bracket Pivot Lever
Keeper, Belt, Idler

Bellcrank Clutch Grnd Drv StI

Nut Crown Lock 3/8-16 unc
Nut Crown Lock 5/16-18 unc

Screw 3/8-16x1-1/4
Keeper, Belt, Center Span

Screw 3/8-16x.875
Cover, Pedal
Pulley, Engine

PART

NO.

NO.

64

173937

66 154778 Keeper, Belt, Engine, Fool Proof

121749X

76 STD581075

121748X

78
79 STD580025 Key Woodruff
80 145090 Arm, Shift

165592

81
83 19171216

84

166231

124346X Nut, Self-Thding, Wsh Hd 1/4

112

19091210

127285X
116 72140608
120 73900600
150 175456

166002

156
159 183900 Hub Tapered Flange Shift Lt

161 72140406
162

73680400
74780416

19091210
166 17490510

165492
169 165580

178394

170

169613
198 169593 Washer Nyliner 7/8 ID x .105 Hd

202 72110614

DESCRIPTION

Bolt, Hex 7/16-20 x 4 Gr. 5-Thr.
Washer, Lock 7/16

Guide, Mower Drive Belt, R.H.
Spacer, Axle
Washer 25/32 x 1-1/4 x 16 Ga.
E-Ring
Key, Square 2.0 x .1845/1865
Washer 25/32 x 1 -5/8 x 16 Ga

Shaft Asm Cross Tapered 650 20
Washer 17/32 x 3/4 X 16 Ga.

Link Transaxle
Nut, Nylock

Retainer Spring 1”
Washer 9/32 X 3/4 X 10 Ga.
Strap Torque 90 Degrees
Bolt Rdhd Sqneck 3/8-16 x 1
Nut Lock Fig. 3/8-16 unc
Spacer Retainer
Washer 13/32 X 2 X 10 Ga.
Washer Srrted 5/16 ID x 1.125

Bolt Rdhd Sqnk 1/4-20 x 3/4 Gr.5
Nut Crownlock 1/4-20 unc
Bolt Hex Fin 1/4-20 Unc x 1 Gr. 5
Washer 9/32 x 3/4 x 10 Ga.

Screw 5/16-18 X 5/8 TT Yellow
Bolt Shoulder 5/16-18 x.561
Plate Fastening Lt
Keeper Belt Transaxle Gear
Nyliner Snap-In 5/8 ID

Bolt Rdhd. 3/8-16 x 1 -3/4 Gr. 5
Nut Hex Flange Lock

NOTE: All component dimensions given in U. S.

inches 1 inch = 25.4 mm

37

STEERING

TRACTOR -- MODEL NUMBER 917.273770

-38

-12

38

STEERING

TRACTOR - MODEL NUMBER 917.273770

KEY PART
NO. NO.

1

184704X428

2

184706 Axle Assembly
3 169840 Spindle Assembly, LH.
4

169839 Spindle Assembly R.H.

6266H Bearing, Race, Thrust, Hardened

5

121748X

6

12000029 Ring, Klip

8

175121 Draglink

10
11 STD551137 Washer, Lock
12

73940800

13 136518

145212

15
17 180641

126847X Bushing, Link, Drag

26
28 19131416

17000612 Screw 3/8-16x3/4

29

30 STD561210
32

130465
36 155099
37 152927 Screw
38 159946X428 Insert, Steering Wheei

19182411 Washer 9/16 ID x 1-1/2 OD 11 Ga.

39
40 73540600
41

159945
42

145054X428

121749X Washer 25/32 x 1-1/4 x 16 Ga.

43
44

180640
46 184946X505 Cap, Spindle
51 73540400
54

71130420

160367

65
67

72140618

169827

68
71

175146
82

169835 Bracket Susp- Chassis Front
87

173966
88 175118 Bolt Shoulder 7/16-20 unc
91 175553

DESCRIPTION

Steering Wheei

Washer 25/32 x 1-5/8 x 16 Ga.

Nut Hex Jam Topiock 1/2-20 unf
Spacer Bearing Axle Front
Nut, Hex Flange Lock
Shaft Assembly Steering

Washer 13/32 X 7/8 X 16 Ga.
Pin Cotter

Rod, Tie
Bushing, Steering

Nut Crownlock 3/8-24
Adaptor, Steering Wheel
Boot, Steering Shaft

Extension Shaft Steering
Nut Crownlock 1/4-28

Bolt Hex 1/4-28 unf x 1-1/4 Gr. 8
Spacer Brace Axle
Bolt RDHD Sqnk 3/8-16 x 2-1/4
Axle, Brace
Steering Asm-

Washer Flat .781 x 1-1/2 x .14
Clip Steering

NOTE: All component dimensions given in U.S. inches

1 inch = 25-4 mm

39

ENGINE

TRACTOR -- MODEL NUMBER 917.273770

'10

40

ENGINE

TRACTOR - MODEL NUMBER 917.273770

KEY PART

NO. NO.

1

170546X505 Control, Throttle Paddle

2

17720408
3
4

149723

5 159955 Exhaust Asm. Left

6 160589 Exhaust Asm. Right

171877

8

162797

10
13 165391
14

148456 Tube Drain Oil Easy

STD551237 Washer Lock Ext Tooth 3/8

16
17 17060624 Screw 3/8-16 X 1-1/2

169837

23
25 145996X505 Control Choke
26 73920600
29 137180
31 157103
32

161696 Cap Fuel Guage

123487X

33
34 106082X Spacer Pad
37

8543R Line, Fuel

181654

38

109227X

39

17000612

45
72

183906
81 73510400

DESCRIPTION

Screw, HexThd Cut 1/4-20x 1/2
Engine, B&S, (See Breakdown) No. 407577-0283-El
Muffler Exhaust

Bolt 5/16-18 Unc X 3/4 W/Sems
Heat Shield Lt
Gasket, Muffler

Shield, Brn/Dbr Guard

Nut Keps 3/8-24 Unf
Arrestor, Spark
Tank, Fuel

Clamp, Hose

Plug, Oil Drain Easy

Pad idler

Screw Hex Wsh3/8-16 x 3/4

Screw Socket Head 5/16-18x1

Nut Keps Hex 1/4-20 Starter Nut

NOTE

: Al! component dimensions given in U. S.

inches 1 inch = 25.4 mm

41

SEAT ASSEMBLY

TRACTOR -- MODEL NUMBER 917.273770

KEY PART
NO. NO.

1

180597

2

180166

3

71110616

4

19131610

5

145006

STD541437

6

7

124181X

8

17000616
19131614

9

10

180186

11

166369

DESCRIPTION

Seat
Bracket Pnt Pivot Seat {b!k)
Bolt Fin Hex 3/8-16 unc x 1
Washer 13/32 x 3/4 x 10 Ga.
Clip Push in Hinged
Nut Hex Lock w/lns 3/8-16 unc
Spring Seat Cprsn 2 250 BIk Zi
Screw 3/8-16 X 1
Washer 13/32 X1 X 14 Ga.
Pan Pnt Seat (bik)
Knob Seat Adj Wingnut

KEY PART
NO. NO.

12
13
14
15
16

17
21
22
24

121246X
121248X
72050412
134300
121250X
123976X
171852
STD541431
19171912

DESCRIPTION

Bracket Pnt Mounting Switch
Bushing Snap Bik Nyl 50 id
Bolt Rdhd Sht Nk 1/4-20 x 1-1/2
Spacer Split 28 x 96 Zinc
Spring Cprsn 1 27 Bik Pnt

Nut Lock 1/4 Lge Fig Gr. 5 Zinc

Bolt Shoulder 5/16-18 unc-2A

Nut Hex Lock w/ins 5/16-18

Washer 17/32 x 1 -3/16 x 12 Ga.

NOTE: Ail component dimensions given in U.S.

inches 1 inch = 25.4 mm

42

DECALS

TRACTOR - MODEL NUMBER 917.273770

2 7

KEY

PART

NO.

NO.

1

156368

2

188999
3 186280 Decal, Hood, R.H. 15 160396
4

186281 Decal, Hood, L.H.

138047

5

133644

6
7

186869 Decal, Chassis
8 172331

186282 Decal, Fender, Craftsman 184310X428

9

10 156439
11

186283 Decal, Hood Side

12 170852

DESCRIPTION

Decal, Oper. Instr.
Decal, Replacement

Decal, Battery
Decal, Customer Maintenance

Decal, Mower Srs
Decal, Fender Danger
Decal, HP Engine

WHEELS AND TIRES

KEY

PART

NO.

NO.

13 146046 Decal, V-Be!t Drive Schematic
14

179128
184842

16
17

184843 Decal, Grille LH
18 164065
19 149516

.,

138311 Decal, Lift Handle

- -

184311X428

- -

188881 Owner's Manual, English

188882 Owner's Manual, Spanish

—

KEY

PART

NO.

NO.

1 59192 Cap Value Tire
2 65139 Stem Value
3 106222X Tire F Ts 15 x 6 0 - 6 Service
4 59904 Tube inner Front #35060
5 106732X624 Rim Asm 6"front White Service
6 278H Fitting Grease
7 9040H Bearing Flange
8 106108X624 Rim Asm 8“ rear White Service

9 122082X Tire R Ts 20 X 10-8 Service

10 7152J Tube Rear 9 5x8 Service
11 104757X428 Cap Axle BIk 1 50 x 1 00

- - 144334 Seaiant, Tire (10 oz. tube)

NOTE: All component dimensions given in U.S. inches

1 inch = 25.4 mm

DESCRIPTION

Decal, Deck B 42”
Decal, V-Bell Schematic
Decal, Grille RH

Decal, Strg.Whl
Decal, Battery Dngr/Psn Eng

Pad Footrest LH STLT
Pad Footrest RH STLT

DESCRIPTION

43

LIFT ASSEMBLY

TRACTOR -- MODEL NUMBER 917.273770

44

LIFT ASSEMBLY

TRACTOR - MODEL NUMBER 917.273770

KEY

PART

NO.

NO.

1

159460

2 159471

105767X

3
4 12000002 E Ring #5133-62

19211621 Washer 21/32 x 1 x 21 Ga.

5

120183X Bearing Nylong

6
7 125631X

122365X Button Plunger Read

8

11

139865

12

139866
13 STD624008
15 173288
16 73350800
17

175689
18 73800800
19 139868

163552 Retainer Spring

20
31 169865
32

73540600

DESCRIPTION

Washer Asm Inner Spring W/Plunger

Shaft Asm. Lift
Pin Groove

Grip Handle Fluted
Link Asm Lift L.H.

Link Asm Lift R.H.
Retainer Spring
Link Front
Nut Jam Hex 1/2-13 unc

Trunnion BIk Zinc

Nut Lock w/Wsh 1/2-13 unc

Arm Suspension Mower

Bearing, Pvt. Lift
Nut Crownlock 3/8-24

NOTE: Ail component dimensions given in U.S. inches

1 inch = 25.4 mm

45

MOWER DECK

TRACTOR -- MODEL NUMBER 917.273770

46

TRACTOR - MODEL NUMBER 917.273770

MOWER DECK

KEY PART KEY PART
NO. NO.

1 165892 Mower Deck Assembly, 42” 55 155046

2 STD533107

138017

3
4

165460

5 STD624008

178024 Bar Sway Deck 101 136420

6

850857

8

STD551137 Washer, Lock 103 19061216

9

10 140296

11

134149 Blade, 42” MulchingStd

.,

139775

- -

138971

13 137645 Shaft Assembly, Mandrel, Vented
14 128774

110485X

15
16 174493
18 72140505 Bolt, Carriage 5/16-18 x 5/8

132827

19
20 159770
21

STD541431
23 177563 Bracket, Deflector
24 105304X

123713X Spring, Torsion, Deflector

25

110452X

26
27

130968X428
28 19111016 Washer 11/32 x 5/8 x 16 Ga.
29 131491 Rod, Hinge

173984 Screw Thdrol Washer Head

30
31 129963
32

153535 Pulley, Mandrel 185

178342 Nut, Toplock, Flanged

33
34 72110612 Bolt Carr. Sh 3/8-16 x 1-1/2 Gr. 5

131494

36
37 STD551037

STD541437

40
44

140088 Guard, Mandrel, L.H.
45 STD624003
46 137729 Screw, Thd. Roll 1/4-20x5/8 and 116-119).

133944

48
52

139888

184907

53
54

178515

DESCRIPTION

Bolt
Bracket Assembly,Sway Bar, 59 141043
Front
Bracket Sway Bar 38/42” Deck
Retainer Spring

Bolt, Hex 3/8-24 X 1.25 Gr.8
Washer, Hardened

(The following blades are
available)

(For mulching mowers only)
Blade, 42" Mulching Premium
(For better wear when mulching)
Blade, 42” Hi-Lift
(For bagging or discharing)

Housing, Mandrel, Vented
Bearing, Bali, Mandrel
Stripper, Vented Mower Deck 131 STD533710

Bolt, Shoulder
Baffle, Vortex
Nut Crownlock 5/16-18 unc

Cap, Sleeve
Nut, Push

Shield, Deflector

Washer, Spacer

Pulley, Idler, Flat Only - Pulley Not included)
Washer 13/32 x 13/16 x 16 Ga.
Nut Crownlock 3/8-16 unc (Std. Deck-Order separately

Retainer components key nos. 101 -106
Washer, Hardened

Bolt, Shoulder 5/16-18 unc
Arm Assembly, Pad, Brake
Washer, Hardened

NO. NO.

56 165723
67

184939 Knob Custom Oval

68 144959
92 STD541437

102

71081010

104

STD551110
105 160793
106 2029J
111 179292
112

179293 Bracket Gauge Wheel Rh

113 17060510

4898H

116
117

165746 Wheel Gauge Std

118 73930600 Nut Centerlock 3/8-16 unc

19121414

119

19131312

129
130 STD523710 Bolt, Fin Hex 3/8-16 unc x 1 Gr. 5

142

165890
143 157109
144 158634 Keeper Belt 42” Clutch Cable
145 165888

171977

146
147

131335

169022 Spring Return Idler

148
149 165898
150 19091210
152

169676
158 17720408

72140614

159
184

19131410 Washer 13/32 x 7/8 x 10 Ga.

188234

..

130794

- -

169583

NOTE: All component dimensions given in U.S. inches

1 inch = 25.4 mm

DESCRIPTION

Arm, Idler

Spacer, Retainer
Guard, TUV Idler

V-Belt
Nut
Mulcher Cover

Screw
Washer #10
Washer, Lock

Latch Assembly, Bagger

Nut, Weld

Bracket Gauge Wheel Lh

Screw 5/16-18 Unc

Bolt Shoulder

Washer 3/8 x 7/8 x 4 Ga.
Washer 13/32 x 13/16 x 12 Ga.

Bolt, Rdhd Sqnk 3/8-16 unc x1
Arm Spring Brake Mower

Bracket Arm Idler 42”

Pulley Idler Flat

Bolt Carriage idler

Spring Extension

Retainer Spring Yellow Zinc
Washer 9/32 X 3/4 X 10 Ga.

Cable Clutch 42 In

Screw Hex Thd Cut 1/4-20 x 1/2

Bolt Rdhd Sqn 3/8-16 unc x 3/4

Head Asm. Cable Clutch

Mandrel Assembly (includes Hou

sing, Shaft and Shaft Hardware

Replacement Mower, Complete

mulcher cover and gauge wheel

47

TRACTOR -- MODEL NUMBER 917.273770

PEERLESS TRANSAXLE-MODEL NUMBER 206-545C

0—27

(St.—29

20-t “I

® 7U SA IJ ^

1BT -VO JJ «.

/

150

1S0-^

48

29

TRACTOR - MODEL NUMBER 917.273770

PEERLESS TRANSAXLE--MODEL NUMBER 206-545C

KEY PART
NO. NO.

1 772147
2 780086A
3 770128 Transaxle Case
4

776395 Countershaft

5 776409 Output Shaft

778364 Spur Gear {38 teeth)

6
6A

778369

7

778330
8 792180
8A 792047

784352

9

10 784378 Shift Rod & Fork
11 778334 Bevel Gear (30 teeth)
12

778309

13 778368
14

778368

15 778370
17

786188

786102

18

792077A

20
21

792078
22

792079

792073A Screw 1/4 - 20 X 1-1/4”

25
25A 792177
26 792125
27

792035
28 788040

780072

29
29A

780160 Thrust Washer
29B

780051
29C 780199

30 780108
31 780001
31A

780195
32

788083 Oil Seal 5/8”
34 780194
35 780193
35A 780197 Flanged Bushing .751
36 790075 Brake Disk
37 790007

799021

38

DESCRIPTION

Transaxie Cover
Needle Bearing 5/8”

Spur Gear {15 teeth)
Spur Gear {11 teeth)
Shift Key
Woodruff Key #9
Shift Collar

Input Bevel Pinion (13 teeth)
Bevel Gear (13 teeth)
(Include. 14)
Bevel Pinion (13 teeth)
(Include. 13)
Ring Gear (43 teeth)
Drive Pin
Spacer 1.130 X .695
Ball 5/16” dia
Set Screw 3/8 -16 x 3/8”
Spring .310 OD X .625 L

Screw 1/4-20 X 1-3/8”
Retaining Ring (pkg of 2)
Retaining Ring
Retaining Ring
Thrust Washer
.627 IDX.031W

.762 IDX.031W
Thrust Washer
.762 IDX.031W
Anti-Rotation Washer .632
Cup Washer

1.127 IDx .032W
Flat Washer .750 ID x .056W
(Use As Needed)
Flat Washer
.750 ID X .062W

Bushing .563
Flanged Bushing 5 / 8” ID

Brake Pad Plate
Brake Pad (pkg of 2)

KEY PART

NO. NO.

39 786026

792076A

40
41A

790079 Brake Lever

42 792073A Screw 1/4 - 20 X 1-1 /4”

42A 792085A Screw 1/4 - 20 X 2 1/4"
43 792075
44

790025
45 786066 Spacer .2625 x 1.0
46 786086 Brake Lever Bracket

47

774690 Axle (11-15/16” Long)

48 774691
49 778356
50 778338

778354 Spur Gear (23 teeth)

51
52 778352 Spur Gear (19 teeth)

53 778350
54

778346
56 778355

57 778337 Spur Gear (13 teeth)
58 778353
59 778351
60 778349

61 778345

65 780189

776422

66
67

776396

69 792170

786187 Spacer .890

70

71

788069

71B 788092

76 780090

77 788078A Inverted Retaining Ring

792144 Spring .430 OD x .5000 L

79

82

778333

83 778338

792154

85

87 788089A

788093A

150
157 788088A

730229A

180

794712

900

DESCRIPTION

Dowel Pin
Flat Washer
.312 ID x .059W

Locknut 5/16-24
Brake Pad Holder

Axle (16 -1 / 2” long)

Spur Gear (29 teeth)
Spur Gear (27 teeth)

Spur Gear (16 teeth)
Spur Gear (15 teeth)
Spur Gear (11 teeth)

Spur Gear (17 teeth)
Spur Gear (21 teeth)
Spur Gear (24 teeth)
Spur Gear (25 teeth)
Flat Washer
.563 ID X .062W
Input Shaft
Shifter & Brake Shaft
Retaining Ring

Square Cut Ring
“0” Ring
Flat Washer

1.128 IDX.058W

Bevel & Spur Gear (30 & 13

teeth)

Spur Gear (27 teeth)
Oil Fill Plug
Oil Seal 9/16”
Liquid Gasket RTV Silicone
Oil Seal 3 /4”
Gear Oil 80W90
Replacement MST

206-545C Transaxle

NOTE: All component dimensions given In U.S

inches 1 inch ^ 25.4 mm

49

TRACTOR -- MODEL NUMBER 917.273770

BRIOGS & STRATTON ENGINE-MODEL NUMBER 407577, TYPE NUMBER 0283-El

50

TRACTOR - MODEL NUMBER 917.273770

BRIGGS & STRATTON ENGINE-MODEL NUMBER 407577, TYPE NUMBER 0283-El

1 ,.^1 ^

1023A

209

914

227

1022

121 CARBURETOR OVERHAUL KIT

276 (gi
633 »

104 “
105 1

S1A fC05>

977 CARBURETOR GASKET SET

51A

937 ®

51B

•-\p)

51B

51B

L^isaii© 562

141

103

51

51A i

« 9

633

0

231

105

131 I 13Q

987 O

® I

----

-

505 ®

616

552

0

S52A 0

742 ©

404 O

S52A e

691 ®

118

51

51

TRACTOR -- MODEL NUMBER 917.273770

BRIOGS & STRATTON ENGINE-MODEL NUMBER 407577, TYPE NUMBER 0283-El

74

1070

474

363

23

726 695?

165»

309 I

I 513

783

697

52

TRACTOR - MODEL NUMBER 917.273770

BRIGGS & STRATTON ENGINE-MODEL NUMBER 407577, TYPE NUMBER 0283-El

KEY PART KEY PART
NO. NO.

1

699751

2

499585 Kit-Bushing/Seal (Magneto Side) 131
3 391086 •Seai-Gi! (Magneto Side) 133
4 699747
5 693998
5A

693999
7 690962

8 499601

690937 •Gasket-Breather 187A

9

10 690960
11 690942 Tube-Breather 192
12 697227

13 690360
15 690946 Plug-Gil Drain
16 691046 Crankshaft 213

690947

20
22

694966

691054

23
24

222698 Key-Flywheel
25 499588 Piston Assembiy (Standard)
25 499590

499604 Ring Set-Piston (Standard)

26
26 499606 Ring Set-Piston (.020” Oversize)
27

690975
28 690229
29 499583
32

690976
33 499596 Valve-Exhaust
34 499597
35 690963 Spring-Valve (Intake) 309 497595
36 690963 Spring-Valve (Exhaust) 310 690323

690964

40
42

499586 Keeper-Valve

690977

45
46 699748 Camshaft

692714

48
50 699801 Manifold-intake 358 699823 Set-Engine Gasket
51 690949 +• Gasket-Intake 363
51A

699803 Gasket-Intake 383 690966
51B

699800 +• 0i Gasket-intake 385 690960
53 690951
54

699816
73 691055
74 691057 Screw (Rotating Screen)
75 691056 Washer (Flywheei) 445 499486
89 690283 Plug-Oil

699721

98

104

694918 0Pin-Float Hinge

698537

105
108 699808 Valve-Choke 0
117 698784
118 699820
121 699814 Kit-Carburetor Overhaul 977
122 699802 Spacer-Carburetor -h

699807 Carburetor

125
127

699810

DESCRIPTION

Cylinder Assembly

Sump-Engine
Head-Cylinder (Cylinder 1) 141
Head-Cylinder (Cylinder 2)

•+Gasket-Cylinder Head 165 693148
Breather Assembiy 187

Screw (Breather Assembly) 188 690960

•Gasket-Crankcase 209 692909
Screw (Cylinder Head) 211

•Seai-Oil (PTO Side) 216
Screw (Engine Sump)
Flywheei 220

Piston Assembiy (.020” Over
size) 240 691035 Filter-Fuel

Lock-Piston Pin
Pin-Piston 267 695134 Screw (Casing Clamp)
Rod-Connecting
Screw (Connecting Rod)

Valve-Intake 305 691005

Retainer-Vaive 311 497608

Tappet-Valve 333 691060 Armature-Magneto

Short Block

Stud (Carburetor)
Screw (intake Manifold)
Screen-Rotating

Kit-idle Speed

0Valve-Float Needle

Jet-Main (Standard)
Jet-Main (High Altitude)

Plug-Welch NOTE

NO. NO.

130 699809 Valve-Throttle

699812
694914 Float-Carburetor

137

698781 0Gasket-Float Bowl
699811 Kit-Choke Shaft

146 690979

699799 Line-Fuel
691049 Line-Fuel (Molded)

690083
691019

212

699805 Link-Throttle
691021
691022

219 698231

690412 Washer (Governor Lever)

222

698761 Bracket-Control

227

691048

231 690718

690957 Retainer-Breather

250
252

690956
691024 Clamp-Casing

265
276 695410

287

690960

304 695277 Housing-Blower

332

691059 Nut (Flywheel)

334

691061 Screw (Magneto Armature)

337

691043
691062

387

808656 Pump-Fuel

404 690442 Washer (Governor Crank)
405 697820
431 699806 Elbow-Intake

447

691003

447A

690960

•

Included in Engine Gasket Set, Key. No. 358
Included in Carburetor Overhaul Kit, Key. No.
121
Included in Carburetor Gasket Set, Key. No.

t

Included in Valve Gasket Set, Key. No. 1095

: All component dimensions given in U.S. inci

1 inch = 25.4 mm

DESCRIPTION

Kit-Throttle Shaft

Key-Timing
Nut (Ring Gear)

Screw (Control Bracket)

Adjuster-Rocker Arm

Spring-Governor
Spring-Governed idle

Bracket-Choke Control
Link-Choke
Gear-Governor

Lever-Governor Control
Screw (Choke Valve)

Collector-Gi!

-r Washer-Sealing
Screw (Dipstick Tube)

Screw (Blower Housing)
Motor-Starter
Bolt (Starter Motor)
Brush Set

Spark Plug
Flywheei Puller

Wrench-Spark Plug

Screw (Fuel Pump)

Screw (Back Plate)
Filter-Air Cleaner Cartridge

Screw (Air Guide Cover)
Screw (Air Guide Cover)

53

TRACTOR -- MODEL NUMBER 917.273770

BRIOGS & STRATTON ENGINE-MODEL NUMBER 407577, TYPE NUMBER 0283-El

KEY PART
NO. NO.

467

691008

474

696459
505 691029
510 497606

692024

513
523 691036
524 691032 •Seal-Dipstick Tube 965 499613 Cover-Oil Pump

691037 Tube-Dipstick

525
544 692034 Armature-Starter 968 499788
552 690552 Bushing-Governor Crank 975
552A

690553
562

690311
573 691009

95162

601
615 698290
616 691045
628 690960

695414

633
635 66538
654

690958

668 691215

690657 •Seal-Governor Shaft

691
695 693149
697 690372
703 691010 Clip
718 690959

499612 Gear-Ring 1051 691265

726
741

690980

742

690328

750 696999
783 693058
788 691039 Bracket-Fue! Pump
789 698330
797

691029

797A 693167 Nut (Brush Retainer) 1119 691183
798 697890
801 691283 Cap-Drive
802

691286 Cap-End

693757 Housing-Starter

803
842

691031 •Seal-Dipstick/Tube

847 499602
851 493880

691012

865
865A 691014
865B

691015

868 690968 *-h Seal-Valve

DESCRIPTION NO. NO.

Knob-Air Cleaner

Alternator

Nut (Governor Control Lever)
Drive-Starter 929 691003 Screw (Choke Control Bracket)

Clutch-Drive

Dipstick

Bushing-Governor Crank
Bolt (Governor Control Lever)

Piate-Back 1005 499603 Fan-Fiywheei

Clamp-Hose

Retainer-Governor Shaft
Crank-Governor 1019 690103 Kit-Label
Screw (Fuel Pump Bracket)

0Seal-Choke/Throttle Shaft

Boot-Spark Piug

Nut (Carburetor)
Spacer 1026 690981

Screw (Ring Gear)
Screw (Drive Cap)

Pin-Locating 1036
Gear-Timing

Retainer-E Ring 1058 275475 Owner’s Manual
Screw (Oil Pump Cover) 1059 698516
Gear-Pinion 1070

Harness-Wiring 1095

Nut (Brush Retainer) 1100 690973
Screw (Rocker Arm)

Dipstick/Tube Assembly

Terminai-Spark Plug

Cover-Air Guide
Cover-Air Guide
Cover-Air Guide

KEY PART

DESCRIPTION

877

393456
914 691127 Screw (Rocker Cover)
918 694000

943 690589
947

699728 Soienoid-Fue!
967

273638 Fiiter-Pre Cleaner

699502
977

699815
987

699813 OSeal-Throttle Shaft

690954

1013
1017

690770
1022 690971 •-I-Gasket-Rocker Cover

1023 499599

1023A 499600

1024 499054

1026A 690982 Rod-Push (Aluminum)

1027 492932

690972 Arm-Rocker

1029

691042 Shaft-Pump

1035

695704 Label-Emission

1054

280275 Cable-Tie

691674

1090 691293

699822

1127 695407

407577-0025Replacement Engine

1329

273521 Repair Manuai

1330

•

included in Engine Gasket Set, Key. No. 358

Included in Carburetor Overhaul Kit, Key. No.

0

121

Inciuded in Carburetor Gasket Set, Key No.

t

977

Ч-

inciuded in Valve Gasket Set, Key No. 1095

Wire/Connector-Aiternator

Hose-Vacuum

•Seal-0 Ring (Oil Pump Cover)

Cover-Air Cleaner
Bowl-Float
Gasket Set-Carburetor

Nipple-Oil Filter
Screen-Oil Pump

Cover-Rocker (Cylinder 1)
Cover-Rocker (Cylinder 2)
Pump-Oil
Rod-Push (Steel)

Fiiter-Oil

Ring-Retaining

Kit-Screw/Washer
Screw (Flywheel Fan)
Retainer-Brush
Gasket Set-Valve
Pivot-Rocker Arm
Screw (Alternator)
Screw (Float Bow!)

NOTE: All component dimensions given in U.S. inches

1 inch = 25.4 mm

54

cn
Cn

SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION

15 DEGREES MAX.

0

VrVnV^^

. . . ■ ■ . - i I . I . . ■ ■ . ■ ' . - L . .. .. .. .. ... .. . .

. .. .. .. .. .. ... I . , . , ^ . , - 1 . I . r

(

WARNING: To avoid serious in|uty, operate your tractor up and
down the face of slopes, never across the face. Do not mow
slopes greater than 15 degree. Make turns gradually to prevent
tipping or loss of control. Exercise extreme caution when
changing direction on slopes.

1. Fold this page along dotted line Indicated above.

2. Hold page before you so that its left edge is vertically parallel to a tree

trunk or other upright structure.

3. Sight across the fold In the direction of hill slope you want to measure.

4. Compare the angle of the fold with the slope of the hill.

Get it fixed, at your home or ours!

Your Home

For repair - in your home - of all major brand appliances,

lawn and garden equipment, or heating and cooling systems,

no matter who made it, no matter who sold it!

For the replacement parts, accessories and

owner’s manuals that you need to do-it-yourself.

For Sears professional installation of home appliances

and items like garage door openers and water heaters.

1-800-4-MY-HOM^ Anytime, day or night

(1-800-469-4663) (USA and Canada)

www.sears.comwww.sears.ca

Our Home

For repair of carry-in products like vacuums, lawn equipment,

and electronics, call or go on-line for the nearest

Sears Parts and Repair Center.

1 -800-488-1222 Anytime, day or night (U.S A only)

www.sears.com

To purchase a protection agreement {U.S.A.)

or maintenance agreement (Canada) on a product serviced by Sears:

1-800-827-6655 (USA)

Para pedir servicio de reparación

a domicilio, y para ordenar piezas:

1-888-SU-HOGARs^

(1-888-784-6427)

© Sears, Rcebuck and Co

® Registered Trademark / Trademark / Service Mark of Sears, Roebuck and Co
® Marca Registrada / Marca de Fábrica / Marca de Servicio de Sears, Roebuck and Co

Marque de commerce / Marque déposée de Sears, Roebuck and Co

1 -800-361 -6665 (Canada)

Au Canada pour service en français:

l-OOO-LE-FOYER'''^

(1-8CX)-538^37)

www sears ca

02410

188881 Rev. 2 10.3.03 TR/M H Printed in U.S.A.