Craftsman 917.273390 User Manual

Download

Page 1

Owner’s Manual

CRRFTSMRN

LAWN TRACTOR

18.0 HP, 42” Mower Electric Start

6 Speed Transaxle

Model No.

917.273390

This product has a low emission engine which operates differently from previously built engines. Before you start the engine, read and understand this Owner’s Manual.

IMPORTANT:

Read and follow all Safety Rules and Instructions before

operating this equipment.

Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.

Visit our Craftsman website:www.sears.com/craftsman

For answers to your questions about

this product, Call:

1 -800-659-5917

Sears Craftsman Help Line

5 am - 5 pm, Mon - Sat

Page 2

TABLE OF CONTENTS

Warranty.......................... ......................2

Safety Rules

Product Specifications Assembly/Pre-Ope ration .

Operation......................... ....................11

Maintenance Schedule....

.....................

......

......................

......................8

....................

Maintenance.......................

Service and Adjustments....

Storage

Troubleshooting..................

Repair Parts........................

Sears Service

................................

......................

..................17

..................21

..................27

..................28

..................32

....Back Cover

WARRANTY

LIMITED WARRANTY ON CRAFTSMAN RIDING EQUIPMENT For two (2) years from the date of purchase, if this Craftsman Riding Equipment is

maintained, lubricated and tuned up according to the instructions in the owner’s manual. Sears will repair or replace free of charge any parts that are found to be defective in material or workmanship according to the guidelines of coverage listed below. Sears will also provide free labor for these applicable warranted parts for the two full years. During the first 30 days of purchase, there will be no charges to service the product at your home for issues covered by this warranty. (See exclusions below). For your conve nience, IN HOME warranty service will still be available after the first 30 days of pur chase, but a trip charge will apply. This charge will be waived if the Craftsman product is dropped off at an authorized Sears location. For the nearest authorized Sears location, please call 1-800-4-MY-HOME®. This warranty applies only while this product is within the United States.

This Warranty does not cover:

• Expendable items which become worn during normal use, including but not limited to blades, spark plugs, air cleaners, belts, and oil filters. Standard Maintenance Servicing, oil changes, or tune-ups

• Tire replacement or repair caused by punctures from outside objects, such as nails, thorns, stumps, or glass.

• Repairs necessary because of operator abuse, including but not limited to, damage caused by towing objects beyond the capability of the riding equipment, impacting objects that bend the frame or crankshaft, or over-speeding the engine.

• Repairs necessary because of operator negligence, including but not limited to, elec trical and mechanical damage caused by improper storage, failure to use the proper grade and amount of engine oil, failure to keep the deck clear of flammable debris, or failure to maintain the equipment according to the instructions contained in the owner’s manual.

• Engine (fuel system) cleaning or repairs caused by fuei determined to be contami nated or oxidized (stale). In general, fuel should be used within 30 days of its pur chase date.

• Normal deterioration and wear of the exterior finishes, or product label replacement. Riding equipment used for commercial or rental purposes.

LIMITED WARRANTY ON BATTERY For ninety (90) days from date of purchase, if any battery included with this riding equip ment proves defective in material or workmanship and our testing determines the battery will not hold a charge. Sears will replace the battery at no charge. During the first 30 days of purchase, there will be no charges to replace the battery at your HOME. After the first 30 days, for your convenience, IN-HOME warranty service will still be avail able but a trip charge will apply. This charge will be waived if the Craftsman product is dropped off at an authorized Sears location. For the nearest authorized Sears location, please call 1-800-4-MY-HOME®.

This battery warranty applies only while this product is within the United States. This warranty gives you specific legal rights, and you may also have other rights, which

vary, from state to state. Sears, Roebuck and Co.,Dept.817WA, Hoffman Estates, IL 60179

Page 3

SAFETY RULES

IMPORTANT: This cutting machine is capable of amputating hands and feet and throw ing objects. Failure to observe the following safety instructions could result in serious injury or death.

AwARNING: In order to prevent ac

cidental starting when setting up, trans porting, adjusting or making repairs, always disconnect spark plug wire and place wire where it cannot contact spark plug.

AwARNING: Do not coast down a hill in

neutral, you may lose control of the tractor.

WARNING: Tow only the attachments

that are recommended by and comply with specifications of the manufacturer of your tractor. Use common sense when towing. Operate only at the lowest possible speed when on a slope. Too heavy of a load, while on a slope, is dangerous. Tires can lose traction with the ground and cause you to lose control of your tractor.

AwaRNING: Engine exhaust, some of

its constituents, and certain vehicle com ponents contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.

AwaRNING: Battery posts, terminals

and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.

Wash hands after handling.

I qeneral operation

• Read, understand, and follow all instruc tions in the manual and on the machine before starting.

• Only allow responsible adults, who are familiar with the instructions, to operate the machine.

• Clear the area of objects such as rocks, toys, wire, etc., which could be picked up and thrown by the blade.

• Be sure the area is clear of other people before mowing. Stop machine if anyone enters the area.

• Never carry passengers.

• Do not mow in reverse unless abso lutely necessary. Always look down and behind before and while backing.

• Be aware of the mower discharge direc tion and do not point it at anyone. Do not operate the mower without either the entire grass catcher or the guard in place. Slow down before turning.

Never leave a running machine unat tended. Always turn off blades, set parking brake, stop engine, and remove keys before dismounting. Turn off blades when not mowing. Stop engine before removing grass catcher or unclogging chute. Mow only in daylight or good artificial light.

Do not operate the machine while under the influence of alcohol or drugs. Watch for traffic when operating near or crossing roadways.

Use extra care when loading or un loading the machine into a trailer or truck.

Data indicates that operators, age 60 years and above, are involved in a large percentage of riding mower-related in juries. These operators should evaluate their ability to operate the riding mower safely enough to protect themselves and others from serious injury.

• Keep machine free of grass , leaves or other debris build-up which can touch hot exhaust / engine parts and burn . Do not allow the mower deck to plow leaves or other debris which can cause build up to occur. Clean any oil or fuel spillage before operating or storing the machine . Allow machine to cool before storage.

II. SLOPE OPERATION

Slopes are a major factor related to lossof-control and tipover accidents, which can

result in severe injury or death. All slopes

require extra caution. If you cannot back up the slope or if you feel uneasy on it, do not mow it.

Page 4

SAFETY RULES

DO:

• Mow up and down slopes, not across.

• Remove obstacles such as rocks, tree limbs, etc.

• Watch for holes, ruts, or bumps. Un even terrain could overturn the machine.

Tall grass can hide obstacles.

• Use slow speed. Choose a low gear

so that you will not have to stop or shift while on the slope.

• Follow the manufacturer’s recommend ations for wheel weights or counter weights to improve stability.

• Use extra care with grass catchers or other attachments. These can change the stability of the machine.

• Keep all movement on the slopes slow and gradual. Do not make sudden changes in speed or direction.

• Avoid starting or stopping on a slope. If tires lose traction, disengage the blades and proceed slowly straight down the slope.

DO NOT:

• Do not turn on slopes unless neces sary, and then, turn slowly and gradually downhill, if possible.

• Do not mow near drop-offs, ditches, or embankments. The mower could suddenly turn over if a wheel is over the edge of a cliff or ditch, or if an edge caves in.

• Do not mow on wet grass. Reduced traction could cause sliding.

• Do not try to stabilize the machine by putting your foot on the ground.

• Do not use grass catcher on steep slopes.

III. CHILDREN

Tragic accidents can occur if the operator is not alert to the presence of children. Children are often attracted to the ma chine and the mowing activity. A/ever as sume that children will remain where you last saw them.

• Keep children out of the mowing area and under the watchful care of another responsible adult.

• Be alert and turn machine off if children enter the area.

• Before and when backing, look behind and down for small children.

• Never carry children. They may fall off and be seriously injured or interfere with safe machine operation.

• Never allow children to operate the machine.

• Use extra care when approaching blind corners, shrubs, trees, or other objects that may obscure vision.

IV. SERVICE

• Use extra care in handling gasoline and other fuels. They are flammable and vapors are explosive.

- Use only an approved container.

- Never remove gas cap or add fuel with the engine running. Allow engine to cool before refueling. Do not smoke.

- Never refuel the machine indoors.

- Never store the machine or fuel container inside where there is an open flame, such as a water heater.

• Never run a machine inside a closed area.

• Keep nuts and bolts, especially blade attachment bolts, tight and keep equip ment in good condition.

• Never tamper with safety devices. Check their proper operation regularly.

• Keep machine free of grass, leaves, or other debris build-up. Clean oil or fuel spillage. Allow machine to cool before storing.

• Stop and inspect the equipment if you strike an object. Repair, if necessary, before restarting.

• Never make adjustments or repairs with the engine running.

• Grass catcher components are subject to wear, damage, and deterioration, which could expose moving parts or allow objects to be thrown. Frequently check components and replace with manufacturer’s recommended parts, when necessary.

• Mower blades are sharp and can cut. Wrap the blade(s) or wear gloves, and use extra caution when servicing them.

• Check brake operation frequently. Ad just and service as required.

Page 5

SAFETY RULES

Be sure the area is clear of other people before mowing. Stop machine if anyone enters the area. Never carry passengers or children even with the blades off. Do not mow in reverse unless abso

lutely necessary. Always look down and behind before and while backing. Never carry children. They may fall off and be seriously injured or interfere with safe machine operation. Keep children out of the mowing area and under the watchful care of another responsible adult. Be alert and turn machine off if children enter the area. Before and when backing, look behind and down for small children. Mow up and down slopes (15° Max), not across.

Remove obstacles such as rocks, tree limbs, etc. Watch for holes, ruts, or bumps. Uneven terrain could overturn the machine. Tali grass can hide obstacles.

Use slow speed. Choose a low gear so that you will not have to stop or shift while on the slope. Avoid starting or stopping on a slope. If tires lose traction, disengage the blades and proceed slowly straight down the slope.

If machine stops while going uphill, disengage blades, shift into reverse and back down slowly.

Do not turn on slopes unless necessary, and then, turn slowly and gradually downhill, if possible.

Page 6

PRODUCT SPECIRCATIONS

Gasoline Capacity 1.25 Unleaded

and Type:

Oil Type (API-SF-SJ):

Oil Capacity;

Spark Plug: Champion RC12YC (Gap: .030")

Ground Speed Forward: (MPH): 1st 1.1

Tire Pressure: Front:

Charging System: 3 Amps Battery

Battery: Amp/Hr:

Blade Bolt Torque: 27-35 Ft. Lbs.

CONGRATULATIONS on your purchase of a new iractor. It has been designed, engi neered and manufactured to give you the best possible dependability and performance. Should you experience any problem you cannot easily remedy, please contact a Sears or other qualified service center. We have competent, well-trained techni cians and the proper tools to service or repair this tractor. Please read and retain this manual. The instructions will enable you to assemble and maintain your tractor properly. Always observe the “SAFETY RULES”.

Regular SAE 30 (above 32°F)

SAE 5W-30(below 32°F) W/Filter 3.5 Pints

W/0 Filter 3.0 Pints

2nd 3rd 4th 5th 6th

Reverse:

Rear;

5 Amps Headlights

Min. CCA;

Case Size: U1R

1.4

2.2

3.3 4 4

4.9

1.4 14 PSI

12 PSI

28 230

CUSTOMER RESPONSIBILITIES

• Read and observe the safety rules.

• Follow a regular schedule in main taining, caring for and using your tractor.

• Follow the instructions under “Mainte

nance” and “Storage” sections of this

owner’s manual.

AwaRNING: This tractor is equipped with an internal combustion engine and should not be used on or near any unim proved forest-covered, brush-covered or grass-covered land unless the engine’s exhaust system is equipped with a spark arrester meeting applicable local or state laws (if any). If a spark arrester is used, it should be maintained in effective working order by the operator.

In the state of California the above is re quired by law (Section 4442 of the Califor nia Public Resources Code). Other states may have similar laws. Federal laws apply on federal lands. A spark arrester for the muffler is available through your nearest Sears service center (See REPAIR PARTS section of this manual).

REPAIR PROTECTION AGREEMENTS

Congratulations on making a smart pur chase. Your new Craftsman® product is designed and manufactured for years of dependable operation. But like all products, it may require repair from time to time. That’s when having a Repair Protection Agreement can save you money and aggravation.

Purchase a Repair Protection Agreement now and protect yourself from unexpected hassle and expense.

Here’s what’s included in the Agreement;

• Expert service by our 12,000 profe sional repair specialists.

• Unlimited service and no charge for parts and labor on all covered repairs.

• Product replacement if your covered product can’t be fixed.

• Discount of 10% from regular price of service and service-related parts not covered by the agreement; also, 10% off regular price of preventive mainte nance check.

• Fast help by phone - phone support from a Sears technician on products requiring in-home repair, plus conve nient repair scheduling.

Once you purchase the Agreement, a simple phone call is all that it takes for you to schedule service. You can cal! anytime day or night, or schedule a service ap pointment online. Sears has over 12,000 professional repair specialists, who have access to over 4.5 million quality parts and accessories. Thai’s the kind of professionalism you can count on to help prolong the life of your new purchase for years to come. Purchase your Repair Protection Agreement today!

Some limitations and exclusions apply. For prices and additional information

call 1-800-827-6655.

SEARS INSTALLATION SERVICE

For Sears professional installation of home appliances, garage door openers, water heaters, and other major home items, in the U S.A. call 1-800-4-MY-HOME®

Page 7

Steering

Wheef Insert

UNASSEMBLED PARTS

Steering Wheel

{1 ) Large Flat Washer

(1) Hex Bolt 1/4-28x1-1/4 (1) Locknut 1/2-20

tn=i-i=r

Steering Wheel

Adapter

T T

Seat

^ 17/32 X 1 -3/16 X 12 Gauge

(1) Knob

(1) Washer

(1) Locknut 1/4-28

Steering Extension

Steering

Boot

Shaft

Keys

(2) Keys

(1) Oil Drain Tube For Future Use

Slope Sheet

Video Cassette

Page 8

ASSEMBLY/PRE-OPERATION

Your new tractor has been assembled at the factory with the exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness. Review the video cassette before you begin.

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assembly

easier. Standard wrench sizes you need

are listed below.

(1) 3/4“ wrench (1) Pliers (2) 7/16“ wrench (1) Utility knife (1) Tire pressure gauge

When right or left hand is mentioned in this manual, it means when you are in the operating position (seated behind the steering wheel).

TO REMOVE TRACTOR FROM CARTON

UNPACK CARTON

1. Remove all accessible loose parts and parts boxes from carton.

2. Cut along dotted lines on all four pan els of carton. Remove end panels and lay side panels flat.

3. Check for any additional loose parts or cartons and remove.

BEFORE REMOVING TRACTOR FROM SKID

ATTACH STEERING WHEEL

ASSEMBLE EXTENSION SHAFT AND

BOOT

1. Slide extension shaft onto lower steer ing shaft. Align mounting holes in ex tension and lower shafts and install 1/4 hex bolt and locknut. Tighten securely.

IMPORTANT: Tighten bolt and nut se

curely to 10-12 ft. lbs torque.

2. Place tabs of steering boot over tab slots in dash and push down to secure.

INSTALL STEERING WHEEL

3. Position front wheels of the tractor so they are pointing straight forward.

4. Remove steering wheel adapter from steering wheel and slide adapter onto steering shaft extension.

5. Position steering wheel so cross bars are horizontal (left to right) and slide inside boot and onto adapter.

6. Assemble large flat washer, 1/2 hex nut and tighten securely.

7. Snap steering wheel insert into center of steering wheel.

8. Remove protective materials from trac tor hood and grill.

IMPORTANT: Check for and remove any staples in skid that may puncture tires where tractor is to roil off skid.

INSTALL SEAT

Adjust seat before tightening adjustment knob.

1. Remove adjustment knob and flat washer securing seat to cardboard packing and set aside for assembly of seat to tractor.

2. Pivot seat upward and remove from the cardboard packing. Remove the cardboard packing and discard.

3. Place seat on seat pan so head of shoulder bolt is positioned over large slotted hole in pan.

4. Push down on seat to engage shoulder bolt in slot and pull seat towards rear of tractor.

Page 9

Pivot seat and pan forward and as semble adjustment knob and fiat washer loosely. Do not tighten. Lower seat into operating position and

sit in seat.

Slide seat until a comfortable position is reached which allows you to press clutch/brake pedal ail the way down.

Get off seat without moving its ad

justed position.

Raise seat and tighten adjustment

9. knob securely.

CHECK BATTERY

1. Lift seat pan to raised position. NOTE: If this battery is put into service after month and year indicated on label (label located between terminals) charge battery for minimum of one hour at 6-10 amps. (See "BATTERY" in Maintenance section of this manual for charging instruc tions).

NOTE: You may now roil or drive your tractor off the skid. Follow the appropriate instruction below to remove the tractor from the skid.

TOROLLTRACTOROEFSKID (See Operation section for location and function of controls)

1. Press lift lever plunger and raise attachment lift lever to its highest po sition.

2. Release parking brake by depressing clutch/brake pedal.

3. Place gearshift lever in neutral (N)

position.

4. Roll tractor forward off skid.

5. Remove banding holding deflector shield up against tractor.

TO DRIVE TRACTOR Off SKID (See Operation section for location and function of controls)

AwARNING: Before starting, read, un derstand and follow ail instructions in the Operation section of this manual. Be sure tractor is in a well-ventilated area. Be sure the area in front of tractor is clear of other people and objects.

1. Be sure all the above assembly steps have been completed.

2. Check engine oil level and fill fuel tank with gasoline.

3. Sit on seat in operating position, depress clutch/brake pedal and set the

parking brake.

4. Place gear shift lever in neutral (N)

position.

5. Press lift lever plunger and raise attachment lift lever to its highest posi tion.

6. Start the engine. After engine has started, move throttle control to idle

position.

7. Depress clutch/brake pedal into full

"BRAKE" position and hold. Move gear

shift lever to 1st gear.

8. Slowly release clutch/brake pedal and slowly drive tractor off skid.

9. Apply brake to stop tractor, set park

ing brake and place gearshift lever in neutral position.

10. Turn ignition key to "STOP" position.

Continue with the instructions that follow.

Page 10

INSTALL MULCHER PLATE (If previously removed)

1. Raise and hold deflector shield in upright position.

2. Place front of mulcher plate over front of mower deck opening and slide into place, as shown.

3. Hook front latch into hole on front of

mower deck.

4. Hook rear latch into hole on back of

mower deck.

AcaUTION: Do not remove deflector shield from mower.

TO CONVERT TO BAGGING OR

DISCHARGING

Simply remove mulcher plate and store in a safe place. Your mower is now ready for discharging or installation of optional grass catcher accessory.

NOTE: It is not necessary to change

blades. The mulcher blades are designed for discharging and bagging also.

wrlCwix I iiiC r fiCwOwitC

The tires on your tractor were overin flated at the factory for shipping purposes. Correct tire pressure is important for best cutting performance.

• Reduce tire pressure to PSI shown in

“PRODUCT SPECIFICATIONS” section of this manual.

TIDC DQ^CCI ID^

CHECK DECK LEVELNESS

For best cutting results, mower hous

ing should be properly leveled. See “TO

LEVEL MOWER HOUSING” in the Service and Adjustments section of this manual.

CHECK FOR PROPER POSITION OF ALL BELTS

See the figures that are shown for replac ing motion and mower blade drive belts in the Service and Adjustments section

of this manual. Verify that the belts are

routed correctly.

CHECK BRAKE SYSTEM

After you learn how to operate your trac tor, check to see that the brake is properly adjusted. See “TO ADJUST BRAKE” in the Service and Adjustments section of this manual.

^CHECKLIST

Before you operate and enjoy your new tractor, we wish to assure that you receive the best performance and satisfaction from this Quality Product.

Please review the following checklist: / All assembly instructions have been

completed. / No remaining loose parts in carton. / Battery is properly prepared and

charged. (Minimum 1 hour at 6 amps). / Seat is adjusted comfortably and tight

ened securely. / All tires are properly inflated. (For ship

ping purposes, the tires were overin

flated at the factory). / Be sure mower deck is properly leveled

side-to-side/front-to-rear for best cutting

results. (Tires must be properly inflated

for leveling). / Check mower and drive belts. Be sure

they are routed properly around pulleys

and inside all belt keepers. / Check wiring. See that all connections

are still secure and wires are properly

clamped. While learning how to use your tractor, pay

extra attention to the following important items:

/ Engine oil is at proper level. / Fuel tank is filled with fresh, clean, regu

lar unleaded gasoline. / Become familiar with all controls - their

location and function. Operate them

before you start the engine. / Be sure brake system is in safe oper

ating condition.

Page 11

OPERATION

These symbols may appear on your tractor or in literature supplied with the product.

Learn and understand their meaning.

REVERSE

NEUTf?

NEUTRAL HIGH

ENGINE OFF LIGHTS ON ENGINE ON ENGINE START PARKING BRAKE PARKING BRAKE PARKING BRAKE

R N

H L |\| *^

LOW CHOKE

(§) 0 oil

FAST

SLOW

LOCKED UNLOCKED

01 ij ^ r~~n

OVER TEMP FUEL OIL PRESSURE BATTERY REVERSE FORWARD MOWER HEIGHT MOWER LIFT

LIGHT

ATTACHMENT ATTACHMENT

CLUTCH ENGAGED CLUTCH DISENGAGED DANGER, KEEP HANDS KEEP AREA CLEAR

FREE WHEEL

(Automatic Models only)

AND FEET AWAY

DANGER indicates a hazard which, if not avoided, will result in death or serious injury.

WARNING indicates a hazard which, if not avoided, could result in death or serious injury.

CAUTION indicates a hazard which, if not avoided, might resuit in minor or moderate injury.

(SEE SAFETY RULES SECTION)

IGNITION

.Jim

SLOPE HAZARDS

Failure to follow instructions could result in serious injury or death. The safety alert symbol

is used to identify safety inform ation about hazards which can

result in death, serious injury and/or property damage.

CAUTION when used without the alert symbol, indicates a situation that could result in damage

to the tractor and/or engine.

HOT SURFACES indicates a hazard which, if not avoided, could result in death, serious injury and/or property damage.

FiRE indicates a hazard which, if not avoided, could result in death, serious injury and/or property damage.

Page 12

KNOW YOUR TRACTOR

READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR

Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and adjustments. Save this manual for future reference.

Our tractors conform to the safety standards of the

American National Standards Institute.

AMMETER - Indicates charging (-i-) or discharging (-) of battery. ATTACHMENT CLUTCH LEVER - Used to engage the mower blades, or other at tachments mounted to your tractor. ATTACHMENT LIFT LEVER - Used to

raise, lower, and adjust the mower deck or other attachments mounted to your tractor. CLUTCH/BRAKE PEDAL - Used for declutching and braking the tractor and starting the engine. GEARSHIFT LEVER - Selects the speed and direction of tractor.

IGNITION SWITCH - Used for starting and

stopping the engine.

LIFT LEVER PLUNGER - Used to release

attachment lift lever when changing its

position. LIGHT SWITCH POSITION - Turns the headlights on and off. PARKING BRAKE LEVER - Locks clutch/

brake pedal into the brake position. THROTTLE/CHOKE CONTROL - Used for starting and controlling engine speed.

Page 13

FORESnHTK BETTER

The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your tractor or performing any adjustments or repairs. We recommend a wide vision safety mask over spectacles or standard safety glasses.

HOWTO USE YOUR TRACTOR

TO SET PARKING BRAKE

Your tractor is equipped with an operator presence sensing switch. When engine is running, any attempt by the operator to leave the seat without first setting the parking brake will shut off the engine.

1. Depress clutch/brake pedal all the way down and hold.

2. Pull parking brake lever up and release pressure from clutch/brake pedal.

Pedal should remain in brake position. Make sure parking brake will hold trac

tor secure.

Attachment Clutch Lever “Engaged” Position

ignition Key

Throttle/ Choke Control

Clutch/ Brake

Pedal

“Disengaged”

Position

STOPPING

MOWER BLADES -

• To stop mower blades, move attachment

clutch lever to “DISENGAGED” position.

GROUND DRIVE -

• To stop ground drive, depress clutch/

brake pedal all the way down.

• Move gearshift lever to neutral (N)

position.

ENGINE -

• Move throttle control to slow position.

NOTE: Failure to move throttle control to slow position and allowing engine to idle before stopping may cause engine to “backfire”.

• Turn ignition key to “STOP” position and

remove key. Always remove key when leaving tractor to prevent unauthorized use.

• Never use choke to stop engine.

“Disengaged" Position

Parking Brake

“Engaged"

Position

Gearshift

“Brake” Position

IMPORTANT: Leaving the ignition switch in any position other than "STOP“ will cause the battery to discharge and go dead. NOTE: Under certain conditions when tractor is standing idle with the engine

running, hot engine exhaust gases may cause “browning” of grass. To eliminate this possibility, always stop engine when stopping tractor on grass areas.

AcAUTION: Always stop tractor com

pletely, as described above, before leaving the operator's position.

TO USE THROTTLE CONTROL

Always operate engine at full throttle.

• Operating engine at less than full

throttle reduces the battery charging

rate.

• Full throttle offers the best bagging and

mower performance.

TO MOVE FORWARD AND BACKWARD

The direction and speed of movement is controlled by the gearshift lever.

1. Start tractor with clutch/brake pedal de pressed and gearshift lever in neutral

(N) position.

2. Move gearshift lever to desired po sition.

3. Slowly release clutch/brake pedal to start movement.

MPORTANT: Bring tractor to a complete

stop before shifting or changing gears.

Failure to do so will shorten the useful life

of your transaxle.

TO ADJUST MOWER CUTTING HEIGHT

The position of the attachment lift lever determines the cutting height.

• Grasp lift lever.

• Press plunger with thumb and move

lever to desired position. The cutting height range is approxi mately 1-1/2 to 4". The heights are mea sured from the ground to the blade tip with the engine not running. These heights are approximate and may vary depending upon soil conditions, height of grass and types of grass being mowed.

Page 14

• The average lawn should be cut to ap proximately 2-1/2 inches during the cool season and to over 3 inches during hot months. For healthier and better looking lawns, mow often and after moderate growth.

• For best cutting performance, grass over 6 inches in height should be mowed twice. Make the first cut relatively high; the second to desired height.

TO OPERATE MOWER

Your tractor is equipped with an operator

presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine. You must

remain fully and centrally positioned in the seat to prevent the engine from hesitating or cutting off when operating your equip

ment on rough, rolling terrain or hills.

1. Select desired height of cut.

2. Start mower blades by engaging at

tachment clutch control. TO STOP MOWER BLADES disengage attachment clutch control.

AcAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped, or the deflector shield in place.

If slowing is necessary, move throttle

control lever to slower position.

If stopping is absolutely necessary, push clutch/brake pedal quickly to brake posi tion and engage parking brake. Move gearshift lever to 1st gear. Be sure you have allowed room for tractor to roil slightly as you restart movement. To restart movement, slowly release parking brake and clutch/brake pedal. Make all turns slowly.

TO TRANSPORT

Raise attachment lift to highest position with attachment lift control. When pushing or towing your tractor, be sure gearshift lever is in neutral (N) position.

Do not push or tow tractor at more than five (5) MPH.

NOTE: To protect hood from damage when transporting your tractor on a truck or a trailer, be sure hood is closed and secured to tractor. Use an appropriate

means of tying hood to tractor {rope, cord,

etc.).

TOWING CARTS AND OTHER ATTACH

MENTS

Tow only the attachments that are recom

mended by and comply with specifications of the manufacturer of your tractor. Use common sense when towing. Too heavy of a load, while on a slope, is dangerous. Tires can lose traction with the ground and cause you to lose control of your tractor.

TO OPERATE ON HILLS

AwARNING: Do not drive up or down

hills with slopes greater than 15° and do not drive across any slope. Use the slope guide at the back of this manual.

• Choose the slowest speed before start ing up or down hills.

• Avoid stopping or changing speed on hills.

BEFORE STARTING THE ENGINE

CHECK ENGINE OIL LEVEL

The engine in your tractor has been shipped, from the factory, already filled with summer weight oil.

1. Check engine oil with tractor on level ground.

2. Remove oil fill cap/dipstick and wipe clean, reinsert the dipstick and screw cap tight, wait for a few seconds, re move and read oil level. If necessary, add oil until “FULL mark on dipstick is reached. Do not overfill.

• For cold weather operation you should

change oil for easier starting (See the oil viscosity chart in the Maintenance section of this manual).

• To change engine oil, see the Mainte

nance section in this manual.

Page 15

ADD GASOLINE

• Fill fuel tank to bottom of filler neck. Do not overfill. Use fresh, clean, regular unleaded gasoline with a minimum of 87 octane. (Use of leaded gasoline will increase carbon and lead oxide deposits and reduce valve life). Do not mix oil with gasoline. Purchase fuel in quan tities that can be used within 30 days to assure fuel freshness.

AcaUTION: Wipe off any spilled oil or

fuel. Do not store, spill or use gasoline near an open flame. IMPORTANT: When operating in temper atures below32°F(0°C), use fresh, clean winter grade gasoline to help insure good cold weather starting. CAUTION: Alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separa tion and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. See Storage Instructions for additional information. Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

TO START ENGINE

When starting the engine for the first time or if the engine has run out of fuel, it will take extra cranking time to move fuel from the tank to the engine.

1. Sit on seat in operating position, depress cluichybrake pedal and set parking brake.

2. Place gear shift lever in neutral (N) position.

3. Move attachment clutch to disengaged position.

4. Move throttle control to choke position.

NOTE: Before starting, read the warm and cold starting procedures below.

5. Insert key into ignition and turn key clockwise to start position and release

key as soon as engine starts. Do

not run starter continuously for more than fifteen seconds per minute. If the engine does not start after several attempts, move throttle control to fast position, wait a few minutes and try again. If engine still does not start,

move the throttle control back to the choke position and retry.

WARM WEATHER STARTING (50° F and above)

6. When engine starts, move the throttle control to the fast position.

• The attachments and ground drive can

now be used. If the engine does not accept the load, restart the engine and allow it to warm up for one minute using the choke as described above.

COLD WEATHER STARTING ( 50° F and below)

6. When engine starts, leave throttle control in choke position until engine warms up and begins to run roughly. Once rough running begins, imme diately move the throttle control to the fast position. Engine warm-up may take from several seconds to several

minutes (the colder the temperature,

the longer the warm-up).

• The attachments can also be used dur

ing the engine warm-up period. NOTE: If at a high altitude (above 3000 feet) or in cold temperatures (below 32 F) the carburetor fuel mixture may need to be adjusted for best engine performance (see TO ADJUST CARBURETOR” in the Service and Adjustments section of this manual).

Page 16

MOWING TIPS

• Mower should be properly leveled for best mowing performance. See “TO LEVEL MOWER HOUSING” in the Service and Adjustments section of this manual.

• The left hand side of mower should be used for trimming.

• Drive so that clippings are discharged onto the area that has already been cut. Have the cut area to the right of the tractor. This will result in a more even distribution of clippings and more uniform cutting.

• When mowing large areas, start by turning to the right so that clippings will discharge away from shrubs, fences, driveways, etc. After one or two rounds, mow in the opposite direction making left hand turns until finished.

MULCHING MOWING TIPS

IMPORTANT: For best performance, keep

mower housing free of built-up grass and

trash. Clean after each use.

• The special mulching blade will recut the grass clippings many times and

reduce them in size so that as they fall onto the lawn they will disperse into the grass and not be noticed. Also, the mulched grass will biodegrade quickly to provide nutrients for the lawn. Always mulch with your highest engine (blade) speed as this will provide the best recut ting action of the blades.

• Avoid cutting your lawn when it is wet. Wet grass tends to form clumps and interferes with the mulching action. The best time to mow your lawn is the early afternoon. At this time the grass has dried, the newly cut area will not be exposed to direct sunlight.

• For best results, adjust the mower cutting height so that the mower cuts off only the top one-third of the grass blades. For extremely heavy grass, re duce your width of cut on each pass and mow slowly.

If grass is extremely tall, it should be mowed twice to reduce load and pos sible fire hazard from dried dippings. Make first cut relatively high; the second to the desired height. Do not mow grass when it is wet. Wet grass will plug mower and leave undesirable clumps. Allow grass to dry before mowing.

Always operate engine at full throttle when mowing to assure better mowing

performance and proper discharge of material. Regulate ground speed by selecting a low enough gear to give the mower cutting performance as well as the quality of cut desired. When operating attachments, select a ground speed that will suit the terrain and give best performance of the at tachment being used.

MAX 1/3

Certain types of grass and grass conditions may require that an area be mulched a second time to completely hide the clippings. When doing a sec ond cut, mow across (perpendicular) to the first cut path. Change your cutting pattern from week to week. Mow north to south one week then change to east to west the next week. This will help prevent matting and graining of the lawn.

Page 17

MAINTENANCE

MAINTENANCE SCHEDULE

FILL IN DATES AS YOU COMPLETE REGULAR SERVICE

Check Brake Operation Check Tire Pressure

Check Operator Presence and

Interlock Systems

Check for Loose Fasteners

Sharpen/Replace Mower Blades

Lubrication Chart

Check Battery Level

Clean Battery and Terminals

Check Transaxle Cooling Chock V-Bolts

Check Engine Oil Level Change Engine Oil (with oil filter)

Change Engine Oil (without oil filter) Clean Air Filter

Clean Air Screen Inspect Muffier/Spark Arrester Replace Oil Filter (If equipped) Clean Engine Cooling Fins Replace Spark Plug Replace Air Filter Paper Cartridge Replace Fuel Filter

1 - Change more oiten when operating under a heavy Joad or

in high ambient temperatures.

2 - Service more often when operating in dirty or dusty conditions.

✓ ✓ ✓

✓ ✓

✓

SERVICE DATES

✓ 5 ✓

✓ 3 ✓ ✓

✓ 4 ✓ ✓ ✓

✓

•^1.2

✓ l£ ✓

✓ 2

✓

✓ 2 ✓ ✓

✓ 2

3 - Replace blades more often when mowing in sandy soil. 4 - Not required it equipped with maintenance-free battery. 5 - Tighten front axle pivot bolt to 35 ft.-lbs, maximum.

Do not overtighten.

✓

GENERAL RECOMMENDATIONS

The warranty on this tractor does not cover items that have been subjected to operator abuse or negligence. To receive ful! value from the warranty, operator must maintain tractor as instructed in this manual. Some adjustments will need to be made periodically to properly maintain your tractor. At least once a season, check to see if you should make any of the adjustments described in the Service and Adjustments section of this manual.

• At least once a year you should replace the spark plug, clean or replace air filter, and check blades and belts for wear. A new spark plug and clean air filter assure proper air-fuel mixture and help your engine run better and last longer.

BEFORE EACH USE

Check engine oil level.

Check brake operation.

Check tire pressure.

Check operator presence and

interlock systems for proper operation.

Check for loose fasteners.

LUBRICATION CHART

®SAE 30 or 10w30 Motor Oil ©General Purpose Grease ©Refer to Maintenance “ENGINE” Section

IMPORTANT: Do not oil or grease the pivot points which have special nylon bearings. Viscous lubricants will attract dust and dirt that will shorten the life of the self-lubricating bearings. If you fee! they must be lubricated, use only a dry, powdered graphite type lubricant sparingly.

Page 18

TRACTOR

Always observe safety rules when per forming any maintenance.

BRAKE OPERATION If tractor requires more than six (6) feet

stopping distance at high speed in highest

gear, then brake must be adjusted. (See “TO ADJUST BRAKE” in the Service and Adjustments section of this manual).

TIRES

• Maintain proper air pressure in al! tires

(See “PRODUCT SPECIFICATIONS” section of this manual).

• Keep tires free of gasoline, oil, or insect

control chemicals which can harm rub ber.

• Avoid stumps, stones, deep ruts, sharp

objects and other hazards that may cause tire damage.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant

may be purchased from your local parts dealer. Tire sealant also prevents tire dry

rot and corrosion.

SYSTEM

Be sure operator presence and interlock systems are working properly. If your trac tor does not function as described, repair the problem immediately.

• The engine should not start unless the

clutch/brake pedal is fully depressed and attachement clutch control is in the disengaged position.

• When the engine is running, any at

tempt by the operator to leave the seat without first setting the parking brake should shut off the engine.

• When the engine is running and the

attachment clutch is engaged, any at tempt by the operator to leave the seat should shut off the engine.

• The attachment clutch should never op

erate unless the operator is in the seat.

BLADE CARE

For best results mower blades must be

kept sharp. Replace bent or damaged

blades.

IMPORTANT: To ensure proper assembly, center hole in blade must align with star on mandrel assembly.

4. Reassemble blade bolt, lock washer

and flat washer in exact order as shown.

5. Tighten blade bolt securely (27-35 Ft. Lbs. torque).

IMPORTANT: Blade bolt is heat treated. If bolt needs replacing, replace only with

approve bolt shown in the Repair Parts.

Mandrel Assembly

Edge Up I

Lock Washer —

^r^Bfade

Flat Washer

Blade Bolt

TO SHARPEN BLADE

NOTE: We do not recommend sharp

ening blade - but if you do, be sure the blade is balanced.

Care should be taken to keep the blade

balanced. An unbalanced blade will cause excessive vibration and eventual damage

to mower and engine.

• The blade can be sharpened with a file or on a grinding wheel. Do not attempt to sharpen while on the mower.

• To check blade balance, you will need a 5/8“ diameter steel bolt, pin, or a cone balancer. (When using a cone balancer, follow the instructions supplied with balancer.)

NOTE: Do not use a nail for balancing blade. The lobes of the center hole may

appear to be centered, but are not.

• Slide blade on to an unthreaded portion of the steel bolt or pin and hold the bolt or pin parallel with the ground. If blade is balanced, it should remain in a horizontal position. If either end of the blade moves downward, sharpen the heavy end until the blade is balanced.

BLADE REMOVAL

1. Raise mower to highest position to al low access to blades.

2. Remove blade bolt, lock washer and fiat washer securing blade.

3. Install new or resharpened blade with trailing edge up towards deck as shown.

Page 19

BATTERY

Your tractor has a battery charging system which is sufficient for normal use. How ever, periodic charging of the battery with an automotive charger will extend its life.

• Keep battery and terminals clean.

• Keep battery bolts tight.

• Keep small vent holes open.

• Recharge at 6-10 amperes for 1 hour. NOTE: The original equipment battery on your tractor Is maintenance free. Do not attempt to open or remove caps or covers. Adding or checking level of electrolyte is not necessary.

TO CLEAN BATTERY AND TERMINALS Corrosion and dirt on the battery and

terminals can cause the battery to “leak” power.

1. Disconnect BLACK battery cable first then RED battery cable and remove battery from tractor.

2. Rinse the battery with plain water and dry.

3. Clean terminals and battery cable ends with wire brush until bright.

4. Coat terminals with grease or petro

leum jelly.

5. Reinstall battery (See “REPLACING

BATTERY" in the SERVICE AND AD

JUSTMENTS section of this manual).

NOTE: Although multi-viscosity oils (5W30, 10W30 etc.) improve starting in cold weather, the oils will result in in creased oil consumption when used above 32°F. Check your engine oil level more frequently to avoid possible engine dam age from running low on oil. Change the oil after every 50 hours of op eration or at least once a year if the tractor is not used for 50 hours in one year. Check the crankcase oil level before start ing the engine and after each eight (8) hours of operation. Tighten oil fill cap/ dipstick securely each time you check the oil level.

TO CHANGE ENGINE OIL

Determine temperature range expected before oil change. Ail oil must meet API service classification SF-SJ.

• Be sure tractor is on level surface.

• Oil will drain more freely when warm.

• Catch oil in a suitable container.

1. Remove oil fill cap/dipstick. Be careful not to allow dirt to enter the engine

when changing oil.

2. Remove yellow cap from end of drain valve and install the drain tube onto the fitting.

Oil Drain Valve

TRANSAXLE COOLING

Keep transaxle free from build-up of dirt

and chaff which can restrict cooling.

V-BELTS

Check V-beits for deterioration and wear after 100 hours of operation and replace

if necessary. The belts are not adjustable. Replace belts if they begin to slip from

wear.

ENGINE

LUBRICATION

Only use high quality detergent oil rated with API service classification SF-SJ. Select the oil’s SAE viscosity grade according to your expected operating temperature.

SAE VISCOSITY GRADES

] I I

C -SO -20 -10 0 50 20 30 40

TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OiL CHANGE

30 32 40 60 so 100

I I i

Drain

Tube

3. Unlock drain valve by pushing inward slightly and turning counterclockwise.

4. To open, pull out on the drain valve.

5. After oil has drained completely close and lock the drain valve by pushing

inward and turning clockwise until the

pin is in the locked position as shown.

6. Remove the drain tube and replace the cap onto the end of the drain valve.

7. Refill engine with oil through oil fill dip stick tube. Pour slowly. Do not overfill.

For approximate capacity see “PROD UCT SPECIFICATIONS” section of this manual. Use gauge on oil fill cap/dipstick for

checking level. For accurate reading, tighten dipstick cap securely onto the tube before removing dipstick. Keep oil at “FULL’ line on dipstick. Tighten cap onto the tube securely when finished.

Page 20

ENGINE OIL filter

Replace the engine oil filter every season

or every other oil change if the tractor is

used more than 100 hours in one year.

AIR FILTER

Your engine will not run properly using a dirty air filter. Replace pre-cleaner after

every 25 hours of operation or every

season. Service paper cartridge every

100 hours of operation or every season,

whichever occurs first.

Service air cleaner more often under dusty

conditions.

1. Pull up on air filter cover handle and rotate towards engine.

2. Remove cover.

3. Carefully remove air filter cartridge and pre-cleaner from base.

4. Clean base carefully to prevent debris from falling into carburetor.

NOTE: If very dirty or damaged, replace

cartridge.

5. Place new pre-cleaner and cartridge firmly in base.

6. Align tabs on cover with slots in blower housing and replace cover.

7. Hook handle on cover and push down on handle to close.

IMPORTANT: Petroleum solvents, such as kerosene, are not to be used to clean the cartridge. They may cause deterio

ration of the cartridge. Do not oil car tridge. Do not use pressurized air to clean cartridge.

CLEAN AIR SCREEN

Air screen must be kept free of dirt and chaff to prevent engine damage from overheating. Clean with a wire brush or compressed air to remove dirt and stub

born dried gum fibers.

ENGINE COOLING SYSTEM

Debris may clog the engine’s air cool ing system. Remove blower housing and

clean area shown to prevent overheating and engine damage.

Air Screen

Clean out chaff and debris

MUFFLER

Inspect and replace corroded muffler and spark arrester (if equipped) as it could cre ate a fire hazard and/or damage.

SPARK PLUG(S)

Replace spark plug(s) at the beginning of each mowing season or after every

100 hours of operation, whichever occurs first. Spark plug type and gap setting are shown in “PRODUCT SPECIFICATIONS” section of this manual.

IN-LINE fuel filter

The fuel filter should be replaced once

each season. If fuel filter becomes clogged, obstructing fuel flow to carbu

retor, replacement is required.

1. With engine cool, remove filter and plug fuel line sections.

2. Place new fuel filter in position in fuel line with arrow pointing towards carbu retor.

3. Be sure there are no fuel line leaks and clamps are properly positioned.

4. Immediately wipe up any spilled gaso line.

Clamp

Fuel Filter

Page 21

CLEANING

• Clean engine, battery, seat, finish, etc. of all foreign matter.

• Keep finished surfaces and wheels free of al! gasoline, oil, etc.

• Protect painted surfaces with auto motive type wax.

SERVICE AND ADJUSTMENTS

WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY

SERVICE OR ADJUSTMENTS:

1. Depress clutch/brake pedal fully and set parking brake.

2. Place gearshift lever in neutral (N) position.

3. Place attachment clutch in “DISENGAGED” position.

4. Turn ignition key to “STOP” and remove key.

5. Make sure the blades and all moving parts have completely stopped.

6. Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

We do not recommend using a garden hose or pressure washer to clean your tractor unless the engine and transmis sion are covered to keep water out. Water in engine or transmission will shorten the useful life of your tractor. Use compressed air or a leaf blower to remove grass, leaves and trash from tractor and mower.

TRACTOR

TO REMOVE MOWER

Mower will be easier to remove from the

right side of tractor.

Place attachment clutch in “DISEN

GAGED” position.

Move attachment lift lever forward to lower mower to its lowest position.

Roll belt off engine pulley. Remove small retainer spring, and remove clutch spring off pulley bolt.

Remove large retainer spring, slide collar off and push housing guide out of bracket.

Disconnect anti-sway bar from chassis

6. bracket by removing retainer spring.

Small Retainer Spring

Clutch Spring

Small Retainer Spring

Clutch Spring

7. Disconnect suspension arms from rear deck brackets by removing retainer springs.

8. Disconnect front links from deck by

removing retainer springs.

9. Raise lift lever to raise suspension arms. Slide mower out from under trac tor.

MPORTANT: If an attachment other than the mower deck is to be mounted on the tractor, remove the front links and hook the clutch spring Into square hole in frame.

TO INSTALL MOWER

1. Raise attachment lift lever to its highest position.

— Square Hole

Engine Pulley

Front Link

Retainer Spring

Anti-Sway Bar

Coliar-

Housing Guide

Large Retainer Spring

Bracket

Retainer Springs {Both Sides)

Deflector Shield

Page 22

Slide mower under tractor with deflec tor shield to right side of tractor. Lower lift lever to its lowest position.

Connect front links to mower deck and secure with retainer springs. Connect suspension arms to rear

5. deck brackets and secure with retainer springs.

Connect anti-sway bar to chassis bracket and secure with retainer spring.

Push clutch cable housing guide into bracket, slide collar onto guide and secure with large retainer spring. Place fiat washer and clutch spring on

8. idler pulley bolt and secure with small retainer spring.

Install belt onto engine pulley.

TO LEVEL MOWER HOUSING

Adjust the mower while tractor is parked on level ground or driveway. Make sure tires are properly inflated (See “PROD

UCT SPECIFICATIONS” section of this manual). If tires are over or underinflated,

you will not properly adjust your mower.

SIDE-TO-SIDE ADJUSTMENT

• Raise mower to its highest position.

• At the midpoint of both sides of mower, measure height from bottom edge of mower to ground. Distance “A” on both sides of mower should be the same or within 1/4" of each other.

• If adjustment is necessary, make adjust ment on one side of mower only.

• To raise one side of mower, tighten lift

FRONT-TO-BACK ADJUSTMENT IMPORTANT: Deck must be level side-to

side. If the following front-to-back adjust

ment is necessary, be sure to adjust both front links equally so mower will stay level side-to-side.

To obtain the best cutting results, the

mower housing should be adjusted so that the front is approximately 1/8" to 1/2"

lower than the rear when the mower is in

its highest position. Check adjustment on right side of trac tor. Measure distance “D” directly in front and behind the mandrel at bottom edge of

mower housing as shown.

• Before making any necessary adjust

ments, check that both front links are equal in length.

• If links are not equal in length, adjust

one link to same length as other link.

• To lower front of mower loosen nut “E”

on both front links an equal number of turns.

• When distance “D” is 1/8" to 1/2"

lower at front than rear, tighten nuts T” against trunnion on both front links.

• To raise front of mower, loosen nut “F”

from trunnion on both front links. Tighten nut “E” on both front links an equal num ber of turns. The two front links must

remain equal in length.

• When distance “D” is 1/8" to 1/2" lower

at front than rear, tighten nut “F” against trunnion on both front links.

• Recheck side-to-side adjustment.

Page 23

TO REPLACE MOWER BLADE DRIVE

BELT

The mower blade drive belt may be re placed without tools. Park the tractor on level surface. Engage parking brake.

BELT REMOVAL -

1. Remove mower from tractor (See “TO REMOVE MOWER” in this section of manual).

2. Work belt off both mandrel pulleys and idler pulleys.

3. Pull belt away from mower.

BELT INSTALLATION -

1. Work belt around both mandrel pulleys and idler pulleys

2. Make sure belt is in all pulley grooves and inside all belt guides.

3. Install mower (See “To Install Mower” in this section of this manual).

Mandrel Pulley -

Measure distance between brake oper

ating arm and nut “A” on brake rod.

If distance is other than 1-1/2“, loosen jam nut and turn nut “A” until distance becomes 1-1/2“. Retighten jam nut against nut “A”.

Road test tractor for proper stopping distance as stated above. Readjust

if necessary. If stopping distance is stiil greater than five (5) feet in highest gear, further maintenance is neces sary. Replace brake pads or contact a Sears or other qualified service center.

With Parking Brake “Engaged”

Mandrel Pulley

TO CHECK AND ADJUST BRAKE

Your tractor is equipped with an adjustable brake system which is mounted on the

right side of the transaxle.

If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be checked and adjusted.

TO CHECK BRAKE

1. Park tractor on a level, dry concrete or paved surface, depress clutch/brake pedal all the way down and engage parking brake.

2. Place gear shift lever in neutral (N) position.

The rear wheels must lock and skid when you try to manually push the tractor for ward. If the rear wheels rotate, the brake needs to be adjusted or the pads need to be replaced.

TO ADJUST BRAKE

1. Depress clutch/brake pedal all the way down and engage parking brake.

TO REPLACE MOTION DRIVE BELT

Park the tractor on level surface. Engage parking brake. For assistance, there is a belt installation guide deca! on bottom side of left footrest.

BELT REMOVAL -

1. Remove mower (See “TO REMOVE MOWER” in this section of manual).

NOTE: Observe entire motion drive belt and position of all belt guides and keepers.

2. Remove belt from stationary idler and clutching idler.

3. Remove belt downward from around engine pulley.

4. Pul! belt slack toward rear of tractor.

Remove belt upwards from transaxle

pulley by deflecting belt keepers.

5. Remove belt from center span keeper and pul! belt away from tractor.

BELT INSTALLATION -

1. Carefully work new belt down between transaxle belt keepers and onto the

input pulley.

2. Slide belt into the center span keeper.

3. Pul! belt toward front of tractor and roll around the top groove of engine pulley.

4. Install belt through stationary idler and clutching idler.

Page 24

5. Make sure beit is in all pulley grooves and inside all belt guides and keepers.

6. Install mower (See “TO INSTALL MOWER” in this section of manual).

TRANSAXLE GEAR SHIFT LEVER NEU TRAL ADJUSTMENT

The transaxle should be in neutral when the gear shift lever is in neutral (N) (lock

gate) position. The adjustment is preset

at the factory; however, if adjustment is

needed, proceed as follows:

1. Make sure transaxle is in neutral (N). NOTE: When the tractor rear wheels move

freely, the transaxle is in neutral.

2. Loosen adjustment bolt in front of the right rear wheel. Position the gear shift lever in the neu

3. tral (N) position. Tighten adjustment bolt securely.

4. NOTE: If additional clearance is needed

to get to adjustment bolt, move mower deck height to the lowest position.

„ , , Neutral Lock Gate Gearshift Lever- '

Adjustment Bolt

TO ADJUST STEERING WHEEL ALIGN MENT

If Steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steer ing wheel and reassemble with crossbars horizontal. Tighten securely.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not adjustable on your tractor. If damage has occurred to affect the front wheel toe-in or camber, contact a Sears or other qualified service center.

TO REMOVE WHEEL FOR REPAIRS

1. Block up axle securely.

2. Remove axle cover, retaining ring and washers to allow wheel removal (rear wheels have a square key - Do not lose).

3. Repair tire and reassemble. NOTE: On rear wheels only: align

grooves in rear wheel hub and axle. Insert

square key.

4. Replace washers and snap retaining ring securely in axle groove.

5. Replace axle cover. NOTE: To seal tire punctures and prevent

flat tires due to slow leaks, purchase and

use tire sealant from Sears. Tire sealant

also prevents tire dry rot and corrosion.

Washers

Retaining Ring

Axle Cover

Square Key (Rear Wheel Only)

TO START ENGINE WITH A WEAK BAT-

AwaRNING: Lead-acid batteries gen

erate explosive gases. Keep sparks, flame and smoking materials away from bat teries. Always wear eye protection when around batteries.

If your battery is too weak to start the

engine, it should be recharged. (See "BAT TERY" in the MAINTENANCE section of

this manual).

If “Jumper cables” are used for emergency starting, follow this procedure:

IMPORTANT: Your tractor is equipped with a 12 volt system. The other vehicle

must also be a 12 volt system. Do not use your tractor battery to start other vehicles.

TO ATTACH JUMPER CABLES -

1. Connect one end of the RED cable to the POSITIVE (+) terminal of each battery(A-B), taking care not to short against tractor chassis.

Page 25

2. Connect one end of the BLACK cable to the NEGATIVE (-) terminal (C) of fully charged battery.

3. Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER -

1. BLACK cable first from chassis and then from the fully charged battery.

2. RED cable last from both batteries.

Weak or Dead Battery

Fully Charged Battery

REPLACING BATTERY

^WARNING: Do not short battery

terminals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery,

remove metal bracelets, wristwatch bands, rings, etc.

Positive terminal must be connected first to prevent sparking from accidental grounding.

1. Lift seat pan to raised position.

Disconnect BLACK battery cable first

then RED battery cable and carefully

remove battery from tractor. Install new battery with terminals in

same position as old battery.

First connect RED battery cable to

positive (+) terminal with hex bolt and

keps nut as shown. Tighten securely.

Slide terminal cover over terminal

Connect BLACK grounding cable to

negative {-) terminal with remaining hex bolt and keps nut. Tighten securely.

Terminal

Cable

TO REPLACE HEADLIGHT BULB

1. Raise hood.

2. Pull bulb holder out of the hole in the backside of the grill.

3. Replace bulb in holder and push bulb

holder securely back into the hole in

the backside of the grill.

4. Close hood.

INTERLOCKS AND RELAYS

Loose or damaged wiring may cause your tractor to run poorly, stop running, or prevent it from starting.

• Check wiring. See electrical wiring

diagram in the Repair Parts section.

TO REPLACE FUSE

Replace with 20 amp automotive-type plug-in fuse. The fuse holder is located behind the dash.

TO REyOVE HOOD AND GRILL AS SEMBLY

Raise hood.

Unsnap headlight wire connector.

Stand in front of tractor. Grasp hood at

sides, tilt toward engine and lift off of tractor.

When replacing hood, be sure to re connect the headlight wire connector.

Page 26

ENGINE

Maintenance, repair, or replacement of the emission control devices and systems, which

are being done at the customers expense,

may be performed by any non-road engine repair establishment or individual. Warranty repairs must be performed by an authorized engine manufacturer's service outlet.

TO ADJUSTTHROTTLE CONTROL CABLE

The throttle control has been preset at the factory and adjustment should not be nec

essary. Check adjustment as described below before loosening cable. If adjust ment is necessary, proceed as follows:

1. With engine not running, move throttle control lever from slow to choke posi tion. Slowly move lever from choke to fast position.

2. Check that holes “A” in governor control lever and hole in governor plate line-up. If holes “A” are not aligned, loosen clamp screw and move throttle cable until holes are aligned. Tighten clamp screw securely.

IMPORTANT: Damage to the needle

valve and the seat in carburetor may result

if screw is turned in too tight. PRELIMINARY SETTING -

1. Air cleaner assembly must be assem bled to the carburetor when making carburetor adjustments.

2. Be sure the throttle control cable is adjusted properly (see above).

FINAL SETTING -

1. Start engine and allow to warm for five minutes. Make final adjustments with engine running and shift/motion control lever in neutral (N) position.

2. Move throttle control lever to slow posi tion. With finger, rotate and hold throttle lever against idle speed screw. Turn idle speed screw to attain 1750 RPM.

3. While still holding throttle lever against idle speed screw, turn idle mixture valve full travel clockwise then coun terclockwise until engine runs rough. Turn valve to a point midway between those two positions. Release throttle lever.

TO ADJUST CARBURETOR

NOTE: The carburetor on this engine is

low emission. It is equipped with an idle fuel adjusting needle with a limiter cap, which allows some adjustment within the

limits allowed by the cap. Do not attempt to remove the limiter cap. The limiter cap cannot be removed without breaking the adjusting needle. The carburetor has been preset at the factory and adjustment should not be nec

essary. However, minor adjustment may

be required to compensate for differences

in fuel, temperature, altitude or load. If the carburetor does need adjustment, proceed as follows:

In general, turning idle mixture valve in

(clockwise) decreases the supply of fuel to the engine giving a leaner fuel/air mix ture. Turning the idle mixture valve out

(counterclockwise) increases the supply of fuel to the engine giving a richer fuel/air

mixture.

ACCELERATION TEST -

4. Move throttle control lever from slow to fast position. If engine hesitates or dies, turn idle mixture valve out (coun terclockwise) 1/8 turn. Repeat test and continue to adjust, if necessary, until engine accelerates smoothly.

High speed stop is factory adjusted. Do not adjust - damage may result. IMPORTANT: Never tamper with the engine governor, which is factory set

for proper engine speed. Overspeed

ing the engine above the factory high speed setting can be dangerous. If you think the engine-governed high speed

needs adjusting, contact a Sears or other qualified service center, which has proper

equipment and experience to make any

necessary adjustments.

Page 27

STORAGE

Immediaîeiy prepare your tractor for stor age at the end of the season or if the trac tor WÜI not be used for 30 days or more.

AwARNING: Never store the tractor

with gasoline in the tank inside a building where fumes may reach an open flame or spark. Allow the engine to coo! before storing in any enclosure.

TRACTOR

Remove mower from tractor for winter storage. When mower is to be stored for a period of time, clean it thoroughly, remove all dirt, grease, leaves, etc. Store in a dean, dry area.

1. Clean entire tractor (See “CLEANING” in the Maintenance section of this manual).

2. Inspect and replace belts, if necessary (See belt replacement instructions in

the Service and Adjustments section of this manual).

3. Lubricate as shown in the Maintenance

section of this manual.

4. Be sure that all nuts, bolts and screws

are securely fastened. Inspect moving parts for damage, breakage and wear.

Replace if necessary.

5. Touch up ail rusted or chipped paint

surfaces; sand lightly before painting.

BATTERY

• Fully charge the battery for storage.

• After a period of time in storage, battery

may require recharging.

• To help prevent corrosion and power

leakage during long periods of storage, battery cables should be disconnected and battery cleaned thoroughly (see “TO CLEAN BATTERY AND TERMINALS” in the Maintenance section of this manual).

• After cleaning, leave cables discon

nected and place cables where they cannot come in contact with battery terminals.

• If battery is removed from tractor for

storage, do not store battery directly on concrete or damp surfaces.

ENGINE

FUEL SYSTEM

MPORTANT: It is important to prevent

gum deposits from forming in essential fuel system parts such as carburetor, fuel hose, or tank during storage. Also, alcohol

blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can dam age the fuel system of an engine while in storage.

• Empty the fuel tank by starting the en gine and letting it run until the fuel lines and carburetor are empty.

• Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

• Use fresh fuel next season.

NOTE: Fuel stabilizer is an acceptable alternative in minimizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or stor age container. Always follow the mix ratio found on stabilizer container. Run engine at least 10 minutes after adding stabilizer to allow the stabilizer to reach the car buretor. Do not empty the gas tank and carburetor if using fuel stabilizer.

ENGINE OIL

Drain oil (with engine warm) and replace with clean engine oil. (See “ENGINE” in the Maintenance section of this manual).

CYLiNDER(S)

1. Remove spark plug(s).

2. Pour one ounce of oil through spark

plug hole(s) into cylinder(s).

3. Turn ignition key to “START” position

for a few seconds to distribute oil.

4. Replace with new spark plug(s).

OTHER

• Do not store gasoline from one season

to another.

• Replace your gasoline can if your can

starts to rust. Rust and/or dirt in your gasoline will cause problems.

• If possible, store your tractor indoors

and cover it to give protection from dust and dirt.

• Cover your tractor with a suitable pro

tective cover that does not retain mois ture. Do not use plastic. Plastic cannot breathe which allows condensation to form and will cause your tractor to rust.

MPORTANT: Never cover tractor while

engine and exhaust areas are still warm.

Page 28

TROUBLESHOOTING CHART:

See appropriate section In manual unless directed to Sears service center

PROBLEM CAUSE CORRECTION Will not Start

Hard to start

1. Out of fuel.

2. Engine not “CHOKED” properly.

3. Engine flooded.

4. Bad spark plug.

5. Dirty air filter.

6. Dirty fuel filter.

7 Water in fuel.

8. Loose or damaged wiring.

9. Carburetor out of adjustment.

10. Engine valves out of adjustment.

1. Dirty air filter.

2. Bad spark plug.

3. Weak or dead battery.

4. Dirty fuel filter.

5. Stale or dirty fuel.

6. Loose or damaged wiring.

7. Carburetor out of adjustment.

8. Engine valves out of adjustment.

1. Fill fuel tank.

2. See “TO START ENGINE" in Operation section.

3. Wait several minutes before attempting to start. Replace spark plug. Clean/replace air filter. Replace fuel filter. Empty fuel tank and carbure tor, refill tank with fresh gas oline and replace fuel filter.

8. Check all wiring.

9. See “To Adjust Carburetor” in Service and Adjustments section.

10. Contact a Sears or other qualified service center.

Clean/replace air filter. Replace spark plug. Recharge or replace battery. Replace fuel filter. Empty fuel tank and refill tank with fresh, clean gasoline. Check all wiring. See “To Adjust Carburetor” in Service and Adjustments section. Contact a Sears or other

8. qualified service center.

Engine will not

turn over

Engine clicks but

will not start

1. Clutch/brake pedal not depressed.

2. Attachment clutch is engaged.

3. Weak or dead battery.

4. Blown fuse.

5. Corroded battery terminals.

6. Loose or damaged wiring.

7. Faulty ignition switch.

8. Faulty solenoid or starter.

9. Faulty operator presence switch(es).

1. Weak or dead battery.

2. Corroded battery terminals.

3. Loose or damaged wiring.

4. Faulty solenoid or starter.

1. Depress clutch/brake pedal.

2. Disengage attachment clutch.

3. Recharge or replace battery.

4. Replace fuse.

5. Clean battery terminals.

6. Check all wiring.

7. Check/replace ignition switch.

8. Check/replace solenoid or starter.

9. Contact a Sears or other qualified service center.

1. Recharge or replace battery.

2. Clean battery terminals.

3. Check all wiring.

4. Check/replace solenoid or starter.

Page 29

TROUBLESHOOTING CHART:

See appropriate section In manual unless directed to Sears service center

PROBLEy CAUSE CORRECTION Loss of power

1. Cutting too much grass/too fast.

2. Throttle in “CHOKP position.

3. Build-up of grass, leaves and trash under mower.

4. Dirty air filter.

5. Low oil ievel/dirty oil.

6. Faulty spark plug.

7. Dirty fuel filter.

8. Stale or dirty fuel.

9. Water in fuel.

10. Spark plug wire loose.

11. Dirty engine air screen/fins.

12. Dirty/ciogged muffler.

13. Loose or damaged wiring.

14. Carburetor out of adjustment.

15. Engine valves out of adjustment.

Raise cutting height/reduce speed. Adjust throttle control. Clean underside of mower housing. Clean/replace air filter. Check oil level/change oil. Clean and regap or change spark plug.

Replace fuel filter.

Empty fuel tank and refill tank with fresh, clean gasoline.

Empty fuel tank and carbure tor, refill tank with fresh gas oline and replace fuel filter.

10. Connect and tighten spark plug wire.

11. Clean engine air screen/fins.

12. Clean/replace muffler.

13. Check all wiring.

14. See “To Adjust Carburetor” in Service and Adjustments section.

15. Contact a Sears or other qualified service center.

Excessive

vibration

Engine continues to run when operator leaves seat with attach

ment clutch engaged

Poor cut - uneven 1. Worn, bent or loose blade.

1. Worn, bent or loose blade.

2. Bent blade mandrel.

3. Loose/damaged part(s).

1. Faulty operator-safety presence control system.

2. Mower deck not level.

3. Buildup of grass, leaves, and trash under mower.

4. Bent blade mandrel.

5. Clogged mower deck vent holes from buildup of grass, leaves, and trash around mandrels.

Replace blade.

Tighten blade bolt.

Contact a Sears or other qualified service center. Tighten loose part(s).

Replace damaged parts.

1. Check wiring, switches and connections. If not corrected, contact Sears or other qualified service center.

1. Replace blade. Tighten blade bolt.

2. Level mower deck.

3. Clean underside of mower housing.

4. Contact a Sears or other qualified service center.

5. Clean around mandrels to open vent holes.

Page 30

TROUBLESHOOTING CHART:

See appropriate section In manual unless directed to Sears service center

PROBLEM CAUSE CORRECTION Mower blades will

not rotate

1. Obstruction in clutch

mechanism. Worn/damaged mower drive belt. Frozen idler pulley. Frozen blade mandrel.

1. Remove obstruction.

2. Replace mower drive belt.

3. Replace idler pulley.

4. Contact a Sears or other qualified service center.

Poor grass discharge

Headlight(s) not

working

(if so equipped)

1. Engine speed too slow.

2. Travel speed too fast.

3. Wet grass.

4. Mower deck not level.

5. Low/uneven tire air pressure.

6. Worn, bent or loose blade.

7. Buildup of grass, leaves and trash under mower.

8. Mower drive belt worn.

9. Blades improperly installed.

10. Improper blades used.

11. Clogged mower deck vent holes from buildup of grass, leaves, and trash around mandrels.

1. Switch is “OFF”.

2. Bulb(s) or lamp(s) burned out.

3. Faulty light switch.

4. Loose or damaged wiring.

5. Blown fuse.

Place throttle control in

“FAST” position.

Shift to slower speed.

Allow grass to dry before mowing.

Level mower deck. Check tires for proper air

5. pressure.

6. Replace/sharpen blade.

Tighten blade bolt.

7. Clean underside of mower housing.

8. Replace mower drive belt.

9. Reinstall blades sharp edge down.

10. Replace with blades listed in this manual.

11 .Clean around mandrels to

open vent holes.

1. Turn switch “ON”.

2. Replace bulb(s) or lamp(s).

3. Check/replace light switch.

4. Check wiring and connections.

5. Replace fuse.

Battery wifi not charge

Engine “backfires’

when turning engine “OFF”

1. Bad battery cell(s).

2. Poor cable connections.

3. Faulty regulator (if so equipped).

4. Faulty alternator.

1. Engine throttle control not set at “SLOW” position for

30 seconds before stopping engine.

1. Replace battery.

2. Check/clean all connections.

3. Replace regulator.

4. Replace alternator.

1. Move throttle control to “SLOW” position and allow

to idle for 30 seconds before stopping engine.

Page 31

SCHEMATIC

TRACTOR - - MODEL NUMBER 917.273390

i-O O

ATT'MENT CLUTCH

BLACK (CLUTCH OFF)

STARTER

iGNmON SWITCH

POSITION CIRCUIT "MAKE”

OFF M+G+A1 NONE

RUN/LIGHT B+A1 A2-PL

RUN B+A1 NONE

START B + S -p A1 NONE

IGNiTION

FUEL SHUT-OFF SOLENOID

(IF SO EQUIPPED)

UNIT

CHARGiNB SYSTEM OUTPUT 3 AMP DC e 3600 BPM

(2 PLUGS ON

TWIN CYL. ENGINES)

36 VOLTS AC MIN. e 3600 HPM (CHABOINQ SYSTEM DISCONNECTED)

NOTE

YOUR TRACTOR iS

EOUIPPED WITH A SPECIAL ALTERNATOR SYSTEM. THE LIGHTS ARE NOT

CONNECTED TO THE

BATTERY, BUT HAVE THEIR OWN ELECTRICAL SOURCE.

BECAUSE OF THIS, THE

BRIGHTNESS OF THE LIGHTS WILL CHANGE WITH ENGINE

SPEED. AT IDLE THE LIGHTS WILL DIM. AS THE ENGINE IS

SPEEDED UP. THE LIGHTS

NON-REMOVABLE

CONNECTIONS

WILL BECOME THEIR BRIGHTEST

REMOVABLE

CONNECTIONS

WIRING INSULATED CUPS

NOTE; IF WIRING INSULATED CLIPS WERE REMOVED FOR

SERVICING OF UNIT, THEY SHOULD BE REPLACED TO PROPERLY SECURE YOUR WIRING.

SPARK

^ PLUG A

U GAP •

HEADLIGHTS

Page 32

ELECTRICAL

REPAIR PARTS

TRACTOR - - MODEL NUMBER 917.273390

Page 33

ELECTRICAL

TRACTOR - - MODEL NUMBER 917.273390

KEY PART NO. NO.

163465 2 74760412 Bolt Hex Hd 1/4-20 unc x 3/4 8 176689 16 176138 21

183759 22 4152J

4799J

146147 Cable Battery 6 Ga. w/16 wire red

25 26 175158 27

73510400 4207J

121305X Switch Plunger Nc Gray

29 30 175566 33 140403 40 179720 Harness Ign 41

71110408

131563 Cover Terminal Red 43 178861 Solenoid

121433X Ammeter Rectangular 6 Amp

45 52

141940 90 180499

NOTE:: All component dimensions give in U.S. inches

1 inch = 25.4 mm

DESCRIPTION

Battery Box Battery Fender

Switch, Interlock Harness Asm Light W/4152j Buib Light #1156

Cable Battery 6 Ga. 11" red

Fuse 20 AMP Nut, Keps Hex 1/4-20 unc

Cable Ground 6 Ga. 12* black

Switch Ign Key Ign Molded Craftsman

Bolt BIk. Fin Hex 1/4-20 unc x 1/2

Protection Wire Loop

Cover Battery Terminal

Page 34

TRACTOR - - MODEL NUMBER 917.273390

CHASSIS AND ENCLOSURES

Page 35

TRACXOR“

CHASSIS AND ENCLOSURES

KEY PART NO. NO.

174619

2 176554 Drawbar

155272 Bumper Hood/Dash

5 9 168337X013

10 STD533710 11

174996 13 172105X010 14

17490608 17

185682X558

184921

STD541437 Nut

26 28 188636 Grille Lens Asm Laser 29 174332X599 Lens, Laser 30 174738X558 31 139976 37

17490508

38 175710

174714

39 60 72140606 64

154798

73680600 114 158112 Keeper Beit Rear LH

115 17060620 142 175702

143 186689 144 175582 Bracket Pnt Footrest STLT

156524

145

189747

166

206 170165 207

17670508

208 17670608 ScrewThdrol 3/8-16x1/2

17000612 Screw Hex Wsh Thdr 3/8-16 x 3/4

209 211 145212 212

175143 Insert Lens Reflective

5479J

- -

MODEL NUMBER 917.273390

DESCRIPTION

Chassis Stamping

Dash Bolt, Carriage 3/8-16x1 Panel, Dash, L.H. Panel, Dash, R.H. ScrewThdrol 3/8-16 X 1/2 Hood Assembly Laser Bumper Hood Large 1.75

Fend/Ftrest Pnt STLT Bracket, Fender Support Screw Thdrol 5/16-18x1 /2 Tyt Bracket Asm. Pivot Mower Rear Bracket Pivot Laser Bolt Rdhd Sqnk 3/8-16 unc x 3/4 Dash Lower STLT Nut Crownlock 3/8-16 unc

Screw 3/8-16 X 1-1/4 Plate Reinforcement STLT Bracket Swaybar Chassis

Jod Pivot Chassis/Hood Screw Hi-Lo #13-16 X 5/8 w/patch Bolt Shoulder 5/16-18 TT Screw Thdrol 5/16-18x1 /2 TYTT

Nut Hexfiange Lock Plug, Button

NOTE: All component dimensions given in U.S. inches

1 inch = 25.4 mm

Page 36

GROUND DRIVE

TRACTOR - - MODEL NUMBER 917.273390

Page 37

TRACTOR - - MODEL NUMBER 917.273390

GROUND DRIVE

KEY PART KEY PART NO. NO.

1 Transaxle (See Breakdown)

2 146682

123666X

3 4

12000028 121520X

17060512 Screw 5/16-18 X 3/4

6 8 165866

10 STD561210 11 105701X

74550412 Boit 1/4-28unf Gr. 8 W/Patch

13 14

10040400

74490544 Boit Hex FLGHD 5/16-18 Gr. 5

15 16 STD541431 18 74780616

STD541437 Nut Lock Hex W/Wsh 3/8-16 unc 84

19 21 106933X 22 130804 24

73350600

106888X

STD551037 Washer 13/32 x 13/16 x 16 Ga. 112

26 27

STD561210 28 175765 29 71673 Cap, Parking Brake 120 73900600 30 174973 Bracket, Transaxle 150 175456 32 74760512 Boit Hex Hd 5/16-18 unc X 3/4 34

175578 Shaft, Foot Pedal 156 120183X Bearing, Nylon

35 36 19211616 37 1572H Pin, Roil

179114

72110622

39 41

175556

127783 Pulley, Idler, V-Groove 166 17490510 Screw 5/16-18 x 5/8 154407 Bellcrank, Clutch

123205X Retainer, Belt

72110612 Bolt HexHd 3/8-16 X 1-1/2

STD541437 Nut Crownlock 3/8-16 unc 197

51 52

STD541431

10571 OX Link, Clutch 202 72110614

105709X Spring, Return, Clutch 212 145212 Nut Hex Fig. Lock

55 56 17060620 57

130801

59 169691

17120614

61 62

8883R

DESCRIPTION

Peerless 206-545C Spring Brake Return Pulley Transaxle 66 154778 Ring Retainer Strap Torque 30 Degrees

Rod Shift Fender Adjust Pin Cotter 1/8x1 CAD 77 123583X

Washer Plate Shift Washer Lock Hvy Heiicai

Nut Lock Hex W/lns. 5/16-18 unc

Bolt Fin Hex 3/8-16 X 1 Gr. 5 Knob 85 150360

Rod, Brake 89 158391X428 Console, Shift Nut, Hex Jam 3/8-16 unc

Spring, Brake Rod 96

Pin Cotter 1/8 X 3/4 CAD. Rod, Parking Brake

Washer

Pulley, Composite, Flat Bolt RDHD 3/8-16 unc x 2-3/4 Gr.5 Keeper, Belt Idler

Nut, Crowniock 5/16-18 unc

Screw 3/8-16 X 1.04 V-Beit Keeper, Center Span NOTE: All component dimensions given in U.S. Screw. 3/8-16X.875 Cover, Pedal

NO. NO.

63 175410 Pulley, Engine 64 173937 65 STD551143

70 134683 74 137057 Spacer

121749X Washer 25/32 x 1-1/4 x 16 Ga.

75 76 STD581075

121748X

78 79 2228M 80 131486

165594 Shaft Asm Cross Tapered

81 82 165711 Spring Torsion 83 19171216

166228 Link Transaxle

124346X

4497H Retainer Spring 1" Zinc/Cad 19091210 127285X

113 116 72140608

151 19133210

166002 158 165589 159 183900 161 72140406 Bolt Rdhd Sqnk 1/4-20 x 3/4 Gr 5 162

73680400 Nut Crownlock 1/4-20 unc 163 74780416 165 165623

165492

168 169 165580

178394 Keeper BeltT/A

170

169613 198 169593

inches 1 inch = 25.4 mm

DESCRIPTION

Bolt Hex 7/16-20 X 4 Gr. 5-1.5 Washer Keeper Belt Engine Hydro Keeper Belt Engine

E-Ring Key, Square

Washer 25/32 x 1 -5/8 x 16 Ga. Key Woodruff Arm Shift

Washer 17/32 x 3/4 x 16 Ga. Nut Lock Center 1/4-20 Nut Self-Thd Wsh-hd 1/4 Zinc Washer 9/32 x 3/4 x 10 Ga.

Strap Torque 90 Degrees Bolt Rdhd Sqneck 3/8-16x1.25 Nut Lock Fig 3/8-16 Spacer Retainer Washer 13/32 x 2 x 10 Ga. Washer Srrted 5/161D x 1.125 Bracket Shift Mount Hub Tapered Flange Shift Lt

Bolt Hex Fin 1/4-20 unc x 1 Gr 5 Bracket Pivot Lever

Bolt Shoulder 5/16-18 x .561 Plate Fastening

Nyliner Snap-in 5/8”!D Washer Nyi 7/8 ID x .105” Hyd Bolt Carr Sh 3/8-16x1 -3/4 Gr.5

Page 38

TRACTOR - - MODEL NUMBER 917.273390

STEERING ASSEMBLY

—38

-12

-39

Page 39

TRACTOR

STEERING ASSEMBLY

KEY PART NO. NO. DESCRIPTION

1 139768 Steering Wheel 2 184706 Axle Assembly 3 169840 Spindle Assembly, L.H. 4 169839 Spindle Assembly, R.H. 5 6266H Bearing, Race, Thrust, Hardened 6 121748X Washer 25/32 x 1 -5/8 x 16 Ga. 8 12000029 Ring, Klip

10 175121 Draglink

11 STD551137 Washer, Lock

12 73940800 Nut Hex Jam Toplock 1/2-20 unf

13 136518 Spacer Brg Axle Front

15 145212 Nut, Hexfiange Lock

17 180641 Shaft Assembly, Steering 26 126847X Bushing, Link, Drag 28 19131416 Washer 13/32 X 7/8 X 16 Ga. 29 17000612 Screw 3/8-16x3/4 30 STD561210 Pin 32 130465 Rod, Tie 36 155099 Bushing, Steering 37 152927 Screw 38 139769 Insert, Steering Wheel 39 19183812 Washer 9/16 x 2-3/8 40 73540600 Nut Crownlock 3/8-24 41 186737 Adaptor, Steering Wheel 42 145054x428 Boot, Steering Shaft 43 121749X Washer 25/32 x 1-1/4 x 16 Ga. 44 180640 Extension Shaft Steering 46 184946X505 Cap, Spindle Red 51 73540400 Nut Crownlock 1/4-28 54 71130420 Bolt Hex 1/4-28 unfx 1-1/4 Gr. 8 65 160367 Spacer Brace Axle 67 72110618 BoltRdhdSqnk 3/8-16x2-1/4 68 169827 Axle, Brace 71 175146 Steering Asm 82 169835 Bracket Susp Chassis Front 87 173966 Washer Flat .781 x 1-1/2 x .14 88 175118 Bolt Shoulder 7/16-20 91 175553 Clip Steering 95 188967 Washer Hardened .793 x 1.637 x .060

MODEL NUMBER 917.273390

NOTE: All component dimensions given in U.S. inches

1 inch = 25.4 mm

Page 40

ENGINE

TRACTOR - - MODEL NUMBER 917.273390

KEY PART NO. NO.

170545 Control, Throttle

17720408 3 4 137352 Muffler

13 165291 14

148456

169837

23 29 137180 31 184900 32 140527

123487X Clamp, Hose

33 37

137040 Line, Fuel

181654

124028X

40 44 17670412

17000612 Screw Hex Wsh Thdr 3/8-16 x 3/4

45 46 19091416 Washer 9/32 x 7/8 x 16 Ga. 72

183906 78 17060620 81 73510400

DESCRIPTION

Screw, Hex Head, Thread Cutting 1/4-20 x 1/2

Engine, (See Breakdown) Briggs Modei No. 31H777-0297-E1

Gasket Tube Drain Oil Easy Shield Brn/Dbr Guard Arrestor, Spark Tank, Fuel Cap Assembly, Fuel Sears, Vented

Plug, Drain Oil Easy Bushing Snap Screw, Hex vi/asher Head, Thd., Roll. 1/4-20 x 3/4

Screw Socket Head 5/16-18 x 1 Screw 3/8-16 X 1-1/4

Nut Keps Hex 1/4-20 unc

NOTE: All component dimensions given in U.S. inches

1 inch = 25.4 mm

Page 41

SEAT ASSEMBLY

TRACTOR - - MODEL NUMBER 917.273390

KEY PART KEY PART NO. NO.

1 140122 Seat

140551 3 71110616 4

19131610

5 145006 Clip, Push-In Hinged

STD541437

6 7 124181X Spring, Seat 22

8 17000616

19131614 Washer 13/32 x 1 x 14 Ga.

10 182493 11

166369 Knob Seat

12 121246X Bracket, Switch Mounting

DESCRIPTION

Bracket, Pivot, Seat 14 72050412 Bolt Washer 13/32x 1 xIOGa.

Nut Screw 3/8-16 X 1-1/2 24 19171912 Pan, Seat

NO. NO.

121248X

13 15 134300

121250X Spring

16 17 123976X Locknut, Flange 1/4 Gr. 5

21 171852

STD541431 127018X Bolt Shoulder 5/16-18 x .62

NOTE: All component dimensions given in U.S.

inches 1 inch = 25.4 mm

DESCRIPTION

Bushing, Snap Bolt, Carriage 1/4-20 x 1-1/2 Spacer, Split .28 x .88

Bolt, Shoulder 5/16-18 unc Nut Washer 17/32 x 1-3/16 x 12 Ga.

Page 42

TRACTOR--MODEL NUMBER 917.273390

DECALS

KEY PART KEY PART NO. NO.

DESCRiPTION

NO. NO.

DESCRIPTiON

156368

189100 Decal, HP Engine 3 184728 4

184729 5 189643

133644 Decal, Customer Maintenance

6 7

184730 Decal, Hood Side 8 172331 Decal, Deck 9 184899

10 156439 11

179128

Decal, Oper. (nstr. Decal, Hood, R.H.

Decal, Hood, L.H. Decal, Hood Replacement

Decal, Fender, Craftsman Decal, Fender Danger Decal, Deck “B" 42”

WHEELS & TIRES

146046 183827

13 14

160396 138047 Decal, Battery Diehard

16 20 149516

138311 184310X428 Pad, Footrest LH STLT 184311X428 Pad, Footrest RH STLT

- -

189279

- -

189280

Decal, V-Belt Drive Schematic Decal, Lower Dash Decal, V-Belt Schematic

Decal, Battery Dngr/Psn Eng Decal, Lift Handle

Owner's Manual, English Owner's Manual, Spanish

KEY PART NO. NO.

59192 65139 106222X 59904

106732X624

278H

9040H

8 106108X624 9 106268X

10 7152J

104757X428 144334

DESCRiPTION

Valve Cap, Tire Stem, Valve Tire, Front Tube, Front Tire (Not Provided, Service Item Only) Rim, Front Fitting, Grease {Front Wheei Only) Bearing, Flange (Front Wheel Only) Rim, Rear

Tlrp Rpar

Tube, Rear Tire (Not Provided, Service Item Only) Cap, Axle Sealant, Tire 10 oz.

NOTE: All component dimensions given in U.S.

inches 1 inch = 25.4 mm

Page 43

LIFT ASSEMBLY

TRACTOR - - MODEL NUMBER 917.273390

KEY

PART

NO.

159460

2 159471 Shaft Assembly, Lift

105767X

3 4 12000002 E-Ring

19211621 Washer 21/32 x 1 x 21 Ga.

120183X Bearing, Nyion

6 7 125631X

122365X Button, Plunger, Red

139865

139866 13 STD624008 15 173288 16 73350800 17

175689 18 73800800 19 139868

163552 Retainer Spring

20 31 169865 32

73540600

NOTE: All component dimensions given in U.S. inches

1 inch = 25.4 mm

DESCRIPTION

Lift Lever Inner Wire Assembly Pin, Groove

Grip, Handle, Fluted Link, Lift, L.H.

Link, Lift, R.H. Retainer Spring Link, Front Nut, Hex, Jam 1/2-13 unc Trunnion Locknut, Hex, with Washer Insert 1/2-13 unc Arm, Suspension, Rear

Bearing, Pvt, Lift Nut, Crowniock 3/8-24

Page 44

MOWER DECK

TRACTOR - - MODEL NUMBER 917.273390

Page 45

MOWER DECK

TRACTOR - - MODEL NUMBER 917.273390

KEY PART NO. NO.

1 165892 Mower Deck Assembly, 42”

2 STD533107

138017 Bracket Assembly,Sway Bar, Front

3 4

165460

5 STD624008

178024

850857 Bolt, Hex 3/8-24 X 1.25 Gr. 8

STD551137 Washer, Lock

10 140296 11

134149

- -

139775

• -

138971

13 137645 14 128774 Housing, Mandrel, Ventecf

110485X Bearing, Bail, Mandrel

15 16 174493 18 72140505

132827 Bolt, Shoulder

19 20 159770 21

STD541431 23 177563 24 105304X

123713X Spring, Torsion, Deflector

110452X Nut, Push

26 27

130968X428 Shield, Defiector 28 19111016 Washer 11/32 x 5/8 x 16 Ga. 29 131491 Rod, Hinge 184

173984 Screw Thdrol DOD PT Hex

30 31 187690 32

153535 Pulley, Mandrel housing, shaft and shaft hardware

178342 Nut, Topiock, Flanged

33 34 72110612 Bolt Carr. Sh. 3/8-16 X 1-1/2 Gr. 5

131494 Pulley, Idler, Flat

36 40 73900600

140088 45 STD624003 46 137729

133944 Washer, Hardened

DESCRIPTION NO. NO.

Bolt Bracket Sway Bar 38/42” eck

Retainer Spring

Bar Sway Deck

Washer, Hardened (The following blades are available) Blade, Muiching (For muiching mowers only) Blade, 42" Mulching Premium (For better wear when mulching) Blade, 42" Hi-Lift (For bagging or discharging) Shaft Assembly, Mandrel, Vented

Stripper, Mower Deck Bolt, Carriage 5/16-18 x 5/8

Baffle, Vortex

Nut Crownlock 5/16-18 unc Bracket, Defiector Cap, Sleeve

Washer, Spacer

Nut Lock Fig. 3/8-16 unc Guard, Mandrel, L.H.

Retainer Screw, Thd. Roll 1/4-20 x 5/8

KEY PART

DESCRIPTION

139888 184907

53 54

178515 55 155046 56 165723 59 141043 67

149846 68 144959 92

73800600 Nut Lock Hex w/tns. 3/8-16

101 136420 102

71081010

103 19061216 104

STD551110

105 160793 106 2029J

19131312 Washer 13/32 x 13/16 x12 Ga.

129 130 STD523710 131 STD533710 142

165890

143 157109 144 158634 Keeper Belt 42” Clutch Cable 145 165888

171977 Bolt Carriage Idler

146 147

131335

169022 Spring Return Idler

148 149 165898 150 19091210 152

169676

158 17720408

72140614

159

19131410

188234

185

- -

130794

• -

169583

Bolt, Shoulder 5/16-18 unc Arm Assembly, Pad, Brake Washer, Hardened Arm, Idler Spacer, Retainer Guard, TUV Idler Knob Custom Oval V-Belt

Mulcher Cover Screw Pan Hd Phillips 10-24 x 5/8 Washer #10 Washer, Lock #10 Latch Assembly, Bagger Nut, Weld

Bolt, Fin Hex 3/8-16 unc x1 Gr. 5 Bolt, Rdhd Sqnk 3/8-16 unc x 1 Arm Spring Brake Mower Bracket Arm Idler 42”

Pulley Idler Flat Spring Extension Retainer Spring Yellow Zinc

Washer 9/32 x 3/4 x 10 Ga. Cable Clutch 42 In Screw Hex Thd Cut 1/4-20 x 1 /2 Bolt Rdhd Sqn 3/8-16 uncx 1-3/4 Washer 13/32 x 7/8 x 10 6a. Head Assy. Cable Clutch Mandrel Assembly (includes

only-pulley not included) Replacement Mower, Complete (Std. Deck-Order separately mulcher cover components key nos. 101-106)

NOTE; All component dimensions given in U.S.inches

1 inch = 25.4 mm

Page 46

TRACTOR - - MODEL NUMBER 917.273390

PEERLESS TRANSAXLE - - MODEL NUMBER 206-545C

29C

'71

^^30 '1

'<1-1

,S7

Page 47

TRACTOR - - MODEL NUMBER 917.273390

PEERLESS TRANSAXLE - - MODEL NUMBER 206-545C

REF PART NO. NO.

1 772147 2 780086A 3 770128 Transaxte Case 4 5 776409 6 6A 7 8 792180 8A 792047 Woodruff Key #9 9

10 784378

11 778334 Bevel Gear (30 teeth)

13 778368

15 778370

18 20 21 22 25

25A 792177 26 792125 27 28 788040 29

29A 29B 29C 780199 30 780108 31 780001

31A 32 34 780194 35 780193 Flanged Bushing 5 / 8” ID

35A 780197 36 790075 37 790007 38 39 786026 Dowel Pin 40

776395 778364 Spur Gear (38 teeth)

778369 778330

784352 Shift Coilar

778309

778368

786188 786102 Spacer 1.130 X .695

792077A 792078 792079 792073A Screw 1/4 -20 X 1-1/4”

792035 780072 Thrust Washer .627 ID x .031W

780160 780051

780195 788083 Oil Seal 5/8”

799021 792076A Flat Washer .312 ID x .059W

DESCRIPTION

Transaxle Cover

Needle Bearing 5/8” Countershaft

Output Shaft Spur Gear (15 teeth)

Spur Gear (11 teeth) Shift Key

Shift Rod & Fork Input Bevel Pinion (13 teeth)

Bevel Gear (13 teeth) (Include.

14) Bevel Pinion (13 teeth) (Include.

13) Ring Gear (43 teeth) Drive Pin

Ball 5/16”dia Set Screw 3/8 -16 x 3/8” Spring .310 OD X .625 L

Screw 1/4-20 x 1-3/8” Retaining Ring (pkg of 2) Retaining Ring Retaining Ring

Thrust Washer .762 ID x .031W Thrust Washer .762 ID x .031W Anti-Rotation Washer .632

Cup Washer 1.127 ID x .032W Fiat Washer .750 ID x .056W (Use As Needed) Fiat Washer .750 ID x .062W

Bushing .563 Flanged Bushing .751

Brake Disk Brake Pad Plate Brake Pad (pkg of 2)

PART

NO. NO.

41A

42 792073A Screw 1/4 - 20 X 1-1 /4”

42A 792085A Screw 1/4 - 20 X 2 1/4” 43 792075 44 45 786066 46 786086 47 48 774691 Axle (16-1 /2” long) 49 778356 50 778338 51 52 778352 Spur Gear (19 teeth) 53 778350 54 56 778355 57 778337 Spur Gear (13 teeth) 58 778353 59 778351 60 778349 61 778345 65 780189 66 67 69 792170 70 71

71B 788092 76 780090 77 788078A inverted Retaining Ring 79 82

83 778338 85 87 788089A

150

157 788088A

180 900

790079

790025

774690

778354 Spur Gear (23 teeth)

778346

776422 Input Shaft 776396

786187 788069

792144 778333

792154 Oil Fill Plug 788093A 730229A

794712

DESCRIPTION

Brake Lever

Locknut 5/16-24 Brake Pad Holder Spacer .2625 x 1.0 Brake Lever Bracket Axle (11-15/16” Long)

Spur Gear (29 teeth) Spur Gear (27 teeth)

Spur Gear (16 teeth) Spur Gear (15 teeth) Spur Gear (11 teeth)

Spur Gear (17 teeth) Spur Gear (21 teeth) Spur Gear (24 teeth) Spur Gear (25 teeth) Flat Washer .563 ID x .062W

Shifter & Brake Shaft Retaining Ring Spacer .890 Square Cut Ring

“0” Ring

Flat Washer 1.128 ID x .058W Spring .430 OD X .5000 L

Bevel & Spur Gear (30 & 13

teeth)

Spur Gear (27 teeth)

Oil Seal 9/16"

Liquid Gasket RTV Silicone Oil Seal 3 /4” Gear Oil 80W90

Replacement MST - 206-545C Transaxie

NOTE: All component dimensions given in U.S. inch

1 inch 25.4 mm

Page 48

TRACTOR--MODEL NUMBER 917.273390

BRiGGS ENGINE-MODEL NUMBER 31H777,TYPE NUMBER 0297-El

Page 49

TRACTOR - - MODEL NUMBER 917.273390

BRiGGS ENGINE-MODEL NUMBER 31H777,TYPE NUMBER 0297-El

1095 VALVE GASKET SET

% a

617 tJ

868 é)

1022

333 I

8S1 S®

Page 50

TRACTOR--MODEL NUMBER 917.273390

BRiGGS ENGINE-MODEL NUMBER 31H777,TYPE NUMBER 0297-El

977 CARBURETOR GASKET SET

137 I

276 (

240

187

527

601 (

Page 51

TRACTOR - - MODEL NUMBER 917.273390

BRiGGS ENGINE-MODEL NUMBER 31H777,TYPE NUMBER 0297-El

KEY PART KEY PART NO. NO.

DESCRIPTION

NO. NO.

DESCRIPTION

1 697174 Cylinder Assembly 2 3 391086 4 5 7 9 697109

20 22

23 24 25

26 699051 Ring Set (Standard) 133 494381

27 28 697099 29 697126

32 692852 Screw (Connecting Rod) 142 33 695760 34 35 691279 Spring-Valve (Intake) 188 691693 36 691279 Spring-Valve (Exhaust) 37 40 43 691968 Slinger-Governor/Oil 216 691840 Link-Choke 45 46 48 50 690193 Manifold-Intake 51 53 54 73 697133 74 697897 Screw (Rotating Screen) 78 691003 89 690283 Plug-Oil 93 94 94A 95 691636 Screw (Throttle Valve) 95A 98 495800 Kit-ldie Speed 98A

399265

697188 Sump-Engine 698147 Head-Cyiinder 117A 699457

699168

697113

697110 13 690360 15 690946

697127 Crankshaft

690947

692125

693557

222698

699052

699054

697559 Ring Set (.020” Oversize)

698469

697263

695761 Vaive-Intake

697108 Guard-Flywheel

691752

690564

698492 Camshaft 227 691374 Lever-Governor Control

697762 Short Block

692137

690227

691148

690602

498030 Kit-ldie Mixture

695425 Kit-ldie Mixture (Nikki) 306

690718 0 Screw (Throttle Valve (Nikki)

695408 Kit-ldie Speed (Nikki) 0 104

690525 0 104A

694918 0 105 231855 0 105A

696136 0

Kit-Bushing/Seal (Magneto Side)

•

Seal-0il (Magneto Side)

•4- Gasket-Cylinder Head

•

Gasket-Breather 118A

Tube-Breather 121 697241 Kit-Carburetor Overhaul

•

Gasket-Crankcase

Screw (Cylinder Head) Plug-Gil Drain 125A Carburetor (For Complete

•

Seal-Oil (PTO Side) 698445) Screw (Crankcase Cover/Sump) Flywheel Key-Flywheel Piston Assembly (Standard) Piston Assembly (.020"

Oversize) 131A

Lock-Piston Pin Pin-Piston 137 Rod-Connecting (Standard) 137A Rod-Connecting (.020” Undersize)

Vaive-Exhaust

202 691841 Link-Mechanical Governor

Retainer-Valve 209 692208

Tappet-Valve

•Q%+ Gasket-intake Stud (Carburetor) Screw (intake Manifold) Screen-Rotating 267 695134 Screw (Casing Clamp)

Screw (Flywheel Guard)

0 Bushing-Throttle Shaft 305

Pin-Float Hinge Pin-Fioat Hinge (Nikki)

Valve-Float Needle 977 Valve-Float Needle (Nikki) +

222 694042

231 691636 232 691842 Spring-Governor

238 691843 Cap-Valve 240 394358 Filter-Fuel 265

276 692255 276A 304

305A

307

•

690577

106

690464

108 108A

695419 Vaive-Choke (Nikki)

117 694352

118 697228

699458

121A 699521 Kit-Carburetor Overhaul (Nikki) 125 698445

127

695005 127A 690727 130 691750 Valve-Throttle 130A

699500 131 494379

699501 Kit-Throttie Shaft (Nikki)

133A 694914 Fioat-Carburetor (Nikki) 135 698780 Tube-Fuel Transfer

281165

698781 0 141 495097 141A

698778

697140 0 146 691639 187

697098 Line-Fuei

192

691986

691024 Clamp-Casing

695410

697783

697102 Screw (Blower Housing)

697103

697107 Shieid-Cylinder

691003

included in Engine Gasket Set, Key. No. 358 included in Carburetor Gverhaul Kit, Key. No. 121 included in Carburetor Gasket Set, Key. No.

Included in Valve Gasket Set, Key. No. 1095

Seat-In let

Vaive-Choke (Manual Choke)

0 Jet-Main (Standard)

Jet-Main (Standard) (Nikki)

Jet-Main (High Attitude) Jet-Main (High Attitude) (Nikki)

Carburetor

Carburetor, Service with

Ptug-Welch Ptug-Welch (Nikki)

Valve-Throttle (Nikki)

Kit-Throttle Shaft

Fioat-Carburetor

0t Gasket-Float Bowl

Gasket-Float Bowl (Nikki) Kit-Choke Shaft (Manual Choke) Kit-Choke Shaft (Nikki)

Nozzle-Carburetor

Key-Timing

Screw (Control Bracket) Adjuster-Rocker Arm

Spring-Governor

Bracket-Control

Screw (Choke Valve)

0t Washer-Sealing

Washer-Sealing

Housing-Blower

Screw (Blower Housing)

Screw (Cyiinder Shield)

NOTE: All component dimensions given in U.S. inches

1 inch = 25.4 mm

Page 52

TRACTOR--MODEL NUMBER 917.273390

BRiGGS ENGINE-MODEL NUMBER 31H777,TYPE NUMBER 0297-El

KEY PART NO. NO.

309 693551 310 690323 311 497608 333 495859 Armature-Magneto 334 337 358 697191 363 19203 383 B9838 404 431 445 462 474

503 505 691251 510 693699 513 523 697086 524 691032 525 527 698467 544 692034 552 697144 Bushing-Governor Crank 559 693675 Screw (Remote Choke Stop) 562 579 691029 584 697112

601 614 616 617 634

634A 635 691909 643 654 684 697157 Screw (Breather Passage Cover) 691 692 690572 Spring-Detent 697 690372 Screw (Drive Cap) 718 690959 729 741 750 691033 757 697607 758 759 783 693713 789 698329 797 693167 Nut (Brush Retainer) 801 691283 Cap-Drive 802 803 830 691095 842 847 851

691061 691043

691691 697122 697634

691261 696459 691532 Strap-Starter

692024

697184 Tube-Dipstick

691119

95162 691620 692012 Crank-Governor 692138 690801

698779

697417 Retainer-Air Filter 690958

692407 • Seal-Governor Shaft

691224 697128

697134 Counterweight 697392 Pin-Counterweight

691286 693757 Housing-Starter

691031 697611 692424 Terminal-Spark Plug

DESCRIPTION

Motor-Starter Bolt (Starter Motor) Brush Set

Screw (Magneto Armature) Plug-Spark Gasket Set-Engine

Flywheel Puller Wrench-Spark Plug Washer (Governor Crank)

Elbow-intake

Filter-Air Cleaner Cartridge Washer (Starter Cable)

Alternator

Nut (Governor Control Lever)

Drive-Starter

Clutch-Drive

Dipstick

• Seal-Dipstick Tube

Clamp-Tube

Starter-Armature

Bolt (Governor Control Lever)

Nut (Starter Cable)

Cover-Breather Passage

Clamp-Hose

Pin-Cotter

0 • Seal-0 Ring (Intake Manifold)

0 Spring/Seal Assembly (Manual

Choke)

0 Spring/Seal Assembly (Nikki)

Boot-Spark Plug

Nut (Carburetor)

Pin-Locating

Clip-Wire

Gear-Timing

Screw (Oil Pump Cover)

Link-Co unte rweight

Gear-Pinion

Harness-Wiring

Cap-End

Stud (Rocker Arm)

• Seal-0 Ring (Dipstick Tube) Dipstick/Tube Assembly

KEY PART NO. NO.

868 690968 •+ Seal-Valve 914 943 690589 947 947A 950 965 499613 Cover-Oil Pump 967 968 697446 975 495933 975A 699502 Bowl-Float (Nikki) 977 690192 Gasket Set-Carburetor 987 987A 698777

1005 1017 1019 1022 1023 1024 499054 1026 692003

1027 492932 1029 691751 1034 690822 Guide-Push Rod 1035 1036 695700 1040 698368 1044 1051 691265 1058 275038 Owner's Manual 1059 698516 Kit-Screw/Washe r 1070 1090 691293 1091 691333 1095 690190 Gasket Set-Valve 1119 691183 1127 695407 1263 1264 697104 Screw (Breather Reed) 1265 697125 1266 1266A 1267 697662 Latch-Blower Housing 1270 697156 1279 690960 1329 1330

• 0

i +

NOTE: All component dimensions given in U.S. inches

690960

694393 Solenoid-Fuel 695423 691657 Screw (Float Bowl)

697015 Filter-Pre Cleaner

691326 0 Seal-Throttle Shaft

697111 690770 Screen-Oil Pump 698814 272475 692492 Cover-Rocker Arm

692011

693784 Shaft-Pump

698139

690372

697124 Reed-Breather

691917 697123 0 Seal-O Ring (Intake Elbow)

31H777-0202 Replacement Engine 272147 Repair Manual

included in Engine Gasket Set, Key. No. 358 included in Carburetor Overhaul Kit, Key. No. 121 included in Carburetor Gasket Set, Key. No. 977 included in Valve Gasket Set, Key. No. 1095

1 inch = 25.4 mm

DESCRIPTION

Screw (Rocker Cover)

• Seal-0 Ring (Oil Pump Cover)

Solenoid-Fuel (Nikki)

Cover-Air Cleaner Bowl-Float

0 Seal-Throttle Shaft (Nikki)

Fan-Flywheel

Kit-Label

•+ Gasket-Rocker Cover

Pump-Oil Rod-Push (Intake) Rod-Push (Exhaust) Filter-Oil

Arm-Rocker

Label-Emission Plate-Trim Screw (Flywheel) Ring-Retaining

Screw (Flywheel Fan) Retainer-Brush Cap-Limiter

Screw (Alternator) Screw-Float Bowl

Support-Blower Housing

•0 Seal-O Ring (Intake Elbow)

Plug-AVS Counterweight Screw (Blower Housing Support)

Page 53

SERVICE NOTES

Page 54

SERVICE NOTES

Page 55

Ol Ol

SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION

~ 5.^0r>t

,1 n I > wu, m r>mv>m>vvv>vvv>mv>vvv>vvv>vvvvwmvvy>mvvvv>vvvv>mvvvv>vvvv>m>vvvvvvv>vvvv>m>vvv>mvvvvnvvv>mvvvvnvvv>vvvvvvv>mv>ffl

WARNING: To avoid serious injury, operate your tractor up and down the face of siopes, never across the face. Do not mow slopes greater than 15 degrees. Make turns graduaily to prevent tipping or ioss of control. Exercise extreme caution when changing direction on slopes.

1. Foid this page aiong dotted line indicated above.

2. Hoid page before you so that its ieft edge is verticaily paraiiel to a tree

trunk or other upright structure.

3. Sight across the fold in the direction of hill slope you want to measure.

4. Compare the angle of the fold with the slope of the hill.

■vvvvvwvvw^

Page 56

Get it fixed, at your home or ours!

Your Home

For repair - in your home - of all major brand appliances,

lawn and garden equipment, or heating and cooling systems,

no matter who made it, no matter who sold it!

For the replacement parts, accessories and

owner’s manuals that you need to do-it-yourself.

For Sears professional installation of home appliances

and items like garage door openers and water heaters.

1-800-4-MY-HOM^ Anytime, day or night

(1-800-469-4663) (U.S.A. and Canada)

www.sears.com www.sears.ca

Our Home

For repair of carry-in products like vacuums, lawn equipment,

and electronics, call or go on-line for the nearest

Sears Parts and Repair Center.

1 -800-488-1222 Anytime, day or night (U.S.A. only)

www.sears.com

To purchase a protection agreement (U.S.A.)

or maintenance agreement (Canada) on a product serviced by Sears:

1 -800-827-6655 (U S A.) 1 -800-361 -6665 (Canada)

Para pedir servicio de reparación

a domicilio, y para ordenar piezas:

1-888-SU-HOGARS^

(1-888-78¿h6427)

® Registered Trademark / ™ Trademark / Service Mark of Sears, Roebuck and Co. ® Marca Registrada / Marca de Fábrica / Marca de Servicio de Sears, Roebuck and Co.

Marque de commerce / Marque déposée de Sears, Roebuck and Co.

Au Canada pour service en français:

1-600-LE-FOYER^c

(1-800-533-6937)

www.sears.ca

02410

189279 Rev. 1 3.25.04 MH Printed in U.S.A.

Craftsman 917.273390 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

Owner’s Manual

LAWN TRACTOR

IMPORTANT:

1 -800-659-5917

II. SLOPE OPERATION

DO NOT:

III. CHILDREN

IV. SERVICE

CUSTOMER RESPONSIBILITIES

REPAIR PROTECTION AGREEMENTS

SEARS INSTALLATION SERVICE

UNASSEMBLED PARTS

Steering Wheel

Keys

Slope Sheet

Video Cassette

ASSEMBLY/PRE-OPERATION

TOOLS REQUIRED FOR ASSEMBLY

BEFORE REMOVING TRACTOR FROM SKID

INSTALL MULCHER PLATE (If previously removed)

CHECK DECK LEVELNESS

CHECK FOR PROPER POSITION OF ALL BELTS

CHECK BRAKE SYSTEM

OPERATION

KNOW YOUR TRACTOR

TO START ENGINE

MOWING TIPS

MAINTENANCE

Lubrication Chart

GENERAL RECOMMENDATIONS

BEFORE EACH USE

TRACTOR

V-BELTS

ENGINE

AIR FILTER

CLEANING

SERVICE AND ADJUSTMENTS

ENGINE

TO ADJUSTTHROTTLE CONTROL CABLE

STORAGE

TRACTOR

BATTERY

OTHER

Hard to start

will not start

Excessive

Poor cut - uneven 1. Worn, bent or loose blade.

Poor grass discharge

Headlight(s) not

Battery wifi not charge

SCHEMATIC

REPAIR PARTS

GROUND DRIVE

ENGINE

SEAT ASSEMBLY

DECALS

WHEELS & TIRES

LIFT ASSEMBLY

MOWER DECK

SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION

Your Home

Our Home

1-600-LE-FOYER^c