Craftsman 580.76225 User Manual

SmARSOwner's Manual

CRAFTSMAN°

6.0 HORSEPOWER
2250 PSI 2.2 GPM

HIGH PRESSURE WASHER

Model No.

580.762250

PRESSURE WASHER /

CAUTION: Before using this
product, read this manual and

follow all Safety Rules and

Operating Instructions.

HOURS: Mon,- Fri. 8 a.m. to 5 p.m. (CST)

SEARS, ROEBUCK and CO., Hoffman Estates, IL 60179 U.S.A.

PartNo.21009Draft3 (2/25/97)

CUSTOMER

HEUPUNE

SAFETY RULES .......................... 2-3

ASSEMBLY .............................. 4-5

OPERATION ............................ 6-10

MAINTENANCE ...................... .V.!1,131 _

SERVICE AND ADJUSTMENTS ._. .....

............. 14

STORAGE ....................... : ....... 15

TROUBLESHOOTING ....................... 16

NOTES .................................. 17

REPLACEMENT PARTS .................. 18-25

HOW TO ORDER PARTS ............ BACK PAGE

LI'MiTI"ED ONE YE_AB_.Y'_kBBAN_;ON CRAFTSMAN HIGH PRESSURE WASHER

For on6_ye'_Tfro"rnthe date of p__ehase, when this Craftsman High Pressure Washer is maintained and operat-
ed according to the-instruction_'h_ the oWner's-rfianual, Sears will repair, free of charge, any defect in material

and wo_mans ihip__

If this washer is used for commercial purposes, this warranty applies for only 90 days from the date of pur-

chase, if-this high-pressureWasher is u§ed for rental purposes, this warranty applies for only 30 days after

date of purchase ..........................

This warranty does not cover:

• Expendable items such as spark plugs and air filters, which become worn during normal use.

• Repairs necessary because of operator abuse or negligence, including damage resulting from no water being
supplied to pump or failure to maintain the equipment according to the instructions contained in the owner's man-

ual.

WARRANTY SERVICE IS AVAILABLE BY RETURNING THE HIGH PRESSURE WASHER TO THE NEAR-

EST SEARS STORE OR OTHER CRAFTSMAN OUTLET IN THE UNITED STATES.

This warranty gives you specific legal rights and you may also have other rights, which vary from state to
state.

SEARS, ROEBUCK AND CO., D/817 WA, Hoffman Estates, IL 60179

CAUTION: ALWAYS DISCONNECT SPARK PLUG WIRE AND PLACE WIRE WHERE IT CANNOT CON-

,_ TACT SPARK PLUG, TO PREVENT ACCIDENTAL STARTING WHEN SETTING UP, TRANSPORTING,

I_ AUTION: Before using this product,

TRAINING:

• Engine exhaust gases contain DEADLY carbon
monoxidegas. This dangerous gas, if breathed in suf-

ficientconcentrations,can cause unconsciousness or

; even death. Operate this equipment only in the open

air where adequate ventilation is available.

• :-i_Gasolineis highly FLAMMABLE and its vapors are

i: EXPLOSIVE. Do not permit smoking, open flames,

i :sparks or heat in the vicinity while handling gasoline.

o: _Avoidspilling gasoline on a hot engine. Allow unit to

_i:!_€ool for 2 minutes before refueling. Comply withall

laws regulating storage and handling of gasoline.

ADJUSTING OR MAKING REPAIRS TO YOUR HIGH PRESSURE WASHER.

Locate this pressure washer in areas away from com-
bustible materials, combustible fumes or dust.

read this manual and follow all Safety
Rules and Operating Instructions.

The high pressure equipment is designed to be used
with Sears authorized parts only. If you use this

equipment with parts that do not comply with mini-
mum specifications, the user assumes all risks and

liabilities.

• Some chemicals or detergents may be harmful if
inhaled or ingested, causing severe nausea, fainting
or poisoning. The harmful elements may cause prop-
erty damage or severe injury.

• Do not allow CHILDREN to operate the Pressure
Washer at any time.

PREPARATION:

• Operate engine only at governed sp_'ed, Running the
engine at excessive speeds increases the hazard of
personal injury. Do not tamper with parts which may

increase or decrease the governed speed.

• Do not wear loose clothing, jewelry or anything that
may be caught in the starter or other rotating parts.

• Before starting the Pressure Washer in cold weather,
check all parts of the equipment and be sure ice has
not formed there, '

• Unitswith broken Ormissingparts,or without

protective housingor covers shouldNEVER be
operated.

• The muffler and air cleaner mustbe installedand
in good conditionbefore operating the Pressure

Washer. These componentsact as spark

arrestorsif the engine backfires.

• Checkthe fuelsystem for leaks or signs of deteri-
orationsuchas chafed or spongy hose, looseor
missingclamps or damaged tank or cap. Correct
all defects before operatingthe Pressure

Washer.

OPERATION:

• Do not spray flammable liquids.

• Never allow any,part of the bod.y..._come in con-

tact with the flu_ostream, uu NU/come in con-
tact with a fluid stream created by a leak in the

highpressure hose.

• High pressure stream of fluidthat this equipment
can producecan pierce skin and its underlying

tissues, leadingto serious injury and possible
amputation.

• Never aim the gun at people, animals or plants.

• High pressure spray can cause paint chips or
otherjoarticlesto become airborneand fly at high

speeos.

• Always wear eye protection when you use this
equipment or when you are in the vicinity where the
equipment is in use.

• Operate the pressure at no more than the PSI
fluid pressure rated for your pressure washer.

• Never move the machine by pulling on the high
pressure hose. Use the handle provided on the

top of the unit.

• Always be certain the spray gun, nozzles and

accessories are correctly attached.

• Never use a spray gun which does not have a
trigger lock or trigger guard in place and in work-

ing order.

• Use a respirator or mask whenever there is a
chance that vapors may be inhaled. Read all

instructions with the mask so you are certain the
mask will provide the necessary protection

against inhaling harmful vapors.

• Highpressure spray may damage fragile items
including glass. Do not point spray gun at glass

when in the jet spray mode.

• Keep the hose connected to machine or the
spray gun while the system is pressurized.

Disconnectingthe hose while the unit is pressur-
ized is dangerous.

• Holdthe spraygun firmly in yourhand before you
start the unit. Failure to do so could result in an

injury from a whipping spray g.un. Do not leave
the spray gun unattended while the machine is

running.

• The cleaning area should have adequate slopes
and drainage to reduce the possibility of a fall

due to slippery surfaces.

• Keep water spray away from electric wiring or
fatal electric shock may result.

• Do not adjust unloader valve to a pressure in
excess of machine rating.

• Do not secure trigger gun in the pull-back (open)
position.

• Do not by-pass any safety device on this

machine.

• The muffler and engine heat up during operation
and remain hot immediately after shutting it

down. Avoid contact with a hot muffler or engine
or you could be severely burned.

MAINTENANCE AND STORAGE:

• Operate and store this unit on a stable surface.

• High pressure hose can develop leaks from wear,
kinking, abuse, etc. Water spraying from a leak is

capable of injecting material into skin.Inspect
hose each time before using it. Check all hoses

for cuts, leaks, abrasions or bulging of cover, or
damage or movement of couplings. If any of
these conditions exist, replace hose immediately.

Never repair high pressure hose. Replace it with
another hose that meets minimum pressure rat-

ing of your pressure washer.

Note: In the State of California a sparkarrestor is
required by law (Section 4442 of the California

Public Resources Code). Other states may have

similar laws. Federal laws apply on federal lands.
Note: If you equip the engine of your pressure wash-

er with a spark arrestor muffler, the spark arrestor
must be maintained in effective working order by the
owner/operator.

You can order a spark arrestor (part # 398067)

through your Sears Service Center.

LOOK FOR THIS SYMBOL TO POINT OUT IMPORTANT SAFETY PRECAUTIONS.
IT MEANS "ATrENTION!!! BECOME ALERT!!! YOUR SAFETY IS INVOLVED."

I

CARTON CONTENTS

The following parts are shipped loosewith your pressure
washer:

• Main Unit -- pressurewasher with wheels and guide

handle

• Product IntroductionVideo

• Nozzle Cleaner Kit

• High Pressure Hose

• Parts Box (whichincludes itemslisted below

• Spray Gun

• Wand Extensionwith Hi-Lo AdjustableNozzle

• Wire Form

• Motor Oil

Become familiar with each piece before assemblingthe

pressurewasher. Check allcontentsagainstthe illustra-
tion on Page 6. If any parts are missingor damaged, call
the PressureWasher Helplineat 1-800-222-3136.

TOOLS REQUIRED FOR ASSEMBLY

• Remove the unit by rolling it out the opening in the
carton, then check carton for additionallooseparts.

HOW TO SET UP YOUR PRESSURE WASHER

For the most part, your Craftsman High Pressure Washer

has been assembled at thefactory. You must, however,
attach the wire form, assemble the spray gun, and attach
the high pressure hose to the pump and spray gun.

Note: Included with your unit is a video cassette that
demonstrateshow to set up yourpressure washer. If

you have a viedo cassette recorderyou may wish toview
the video beforeassemblingyour unit.

• Insertthe wire support withthe longer arm positioned
on the left. Fromthis viewthe hookshould resemble
a "J".

2 adjustable wrenches OR the following wrenches

• 11/16" (17mm) wrench

• 7/8" (23mm) wrench

TO REMOVE PRESSURE WASHER FROM
CARTON

Remove loose parts and parts box includedwith pres-
sure washer. The high pressure hose is packed in the
bottom of the carton on the guide handle end.

Remove the hose.

• Slice two corners at guide handle end of carton from
top to bottom so the panel can be folded down flat,

then remove all packing material.

• Raise guide handle and secure in place.

Loosen knobs to

,/

raise handle

LONG

ARM

SHORT

ARM

Cut lie wraponchemical injectiontube. Remove chemi-
calinjectionfilter, threadchemicaltube through thewire

form and reinsert filter intotube.

Tighten knobs
when handle

straight.

Cut tie wrap from high pressure hose. Connect

• • Place assembled spray gun on holder.
high pressure hose to gun witheither two

adjustable wrenchs or one 11/16" and one 7/8"
wrench.

Remove plastic cap and connect high pressure

hose to pump.

HIGH PRESSURE

OUTLET

Connect nozzle extension to spray gun.

CHECKLIST

Before you operate your new high pressure washer,
to be sure you receive the bestperformance and sat-
isfaction from this quality product, please review the
following checklist:

• All assembly instructions have been completed.

• The high pressure hose connections to the spray
gun and to the pump are tight and secure.

CAUTION: Any attempt to crank or

A

start the engine before it has been
properly serviced with the recommend-

ed oil may result in an engine failure.
See Page 9 for instructions on adding

oil and proper oil specifications.

While learninghow to use your high pressure
washer, pay extra attention to the following important

items:

• Engine oil is at proper level

• Be sure gas tank is filled properlywith clean, -

fresh, unleadedgasoline.

• Becomefamiliar with all controls- their location
and funcUon. Operatethose controlsbefore start-

ingthe engine.