Craftsman 580.751500 Owner's Manual

OWNER'S

MANUAL

MODEL NO.

580.751500

_®

HOURS:

Mon.- Frl. 8 a,m. to 5 p.m

(CST)

CAUTION: Read and Follow

all Safety Rules and Instructions

Before Operating This Equipment

5 HORSEPOWER 1800 PS! 2.5 GPM

HiGH PRESSURE WASHER

o Assembly = Operation . Customer Responsibilities

• Service and Adjustment o Repair Parts

SEARS, ROEBUCK

and CO., HoffmanEstates,' IL 60179 U.S.A.

SAFETY RULES

CAUTION: ALWAYS DISCONNECT SP/_K PLUG WIRE AND PLACE WIRE WHERE IT CANNOT CON- TACT SPARK PLUG, TO PREVENT ACCIDENTAL STARTING WHEN SETTING UP, TRANSPORTING, ADJUSTING OR MAKING REPAIRS TO YOUR HIGH PRESSURE WASHER,

TRAINING:

Engine exhaust gases containDEADLY carbonmon- oxide gas. l_is dangerous gas, if breathed in suffi- cient concentrations, can cause unconsciousnessor

even death. Operate thisequipmentonly in the open air where adequate ventilationis availabteo

= Gasoline is highly FIJ_M_L&.BLEand its vapors are

EXPLOSIVE. Do not permitsmoking, open flames, sparks or heat in the vicinitywhile handlinggasoline. Avoid spillinggasoline on a hot engine. Allow unit to

coolfor 2 minutes before refueling. Comply with all laws regulating storageand handhngofgasoline_

= Locate this pressurewasher inareas away from com-

bustiblematerials, combustiblefumes or dust=

= The highpressure equipment is designed to be used

with Sears authorized parts only. If you use this equipmentwithpartsthat do notcomplywithminimum

specifications,the user assumes all nsks and liabili- ties.

• Some chemP-.atsor detergents may be harmful if inhaledor ingested, causingsevere nausea, fainting

or poisoning. The harrr_,_!elements may cause prop. erty damage or severe injury.

• Do not allow CHILDREN to operate the Pressure

Washer at any time.

PREPARATION:

• Operate engine onlyat governedspeed. Runningthe engine at excessive speeds increases the hazard of personalinjury. Do not tamper with partswhich may increaseor decrease the governedspeed.

= Do not wear loose clothing, jewelry or anything that

may be caught in the starteror other rotatingparts.

" Beforestartingthe PressureWasher in coldweather,

check al! parts of the equipmentand be sure ice has

notformed there.

• Unitswith broken or missingparts, or withoutprotec-

tive housingor covers shouldNEVER be operated°

" The muffler and air cleaner must be installed and in

j_oodconditionbeforeoperatingthe PressureWasher.

hesecomponents act as sparkarrestors ifthe engine

backfires.

• Check the fuel systemfor leaks or signsofdeteriora-

tion suchas chafed or spongyhose, loose or missing clamps or damaged tank or cap. Correct all defects

beforeoperating the PressureWasher.

OPERATION:

" Do notspray flammable liquids.

• Never aim the gunat people, animals or plants.

_' Always wear'eye protectionwhen you use this equip-

ment orwhen youare in the vicinitywhere the equip- ment is in use.

• Operate the pressure at no more than the PSI fluid pressurerated for your pressure washer.

= Never move themachine by putlingonthe high pres-

sure hose. Use the handle providedon the top of the uniL

= Always be certainthe spray gun, nozzles and acces-

soriesare correctlyattached.

_' Never use a spray gunwhich does not have a trigger

lockor triggerguard in place and in working order.

=' Use a respiratoror mask whenever there is a chance

that vaporsmay be inhaled. Read all instructionswith the mask so you are certain the mask will providethe

necessaryprotectionagainstinhalingharmfulvapors_

= Highpressurespray may damage fragileitems includ-

ingglass. Do notpoint spraygunat glasswheninthe

jet spray mode.

" Keepthe hoseconnectedto machineor the spray gun

while the system is pressurized. Disconnecting the

hose whilethe unitispressurized is dangerous,

q' Holdthe spraygun firmlyin your handbefore youstart

the uniL Failureto do so could result in an injuryfrom

a whipping spray gun. Do not leave the spray gun unattendedwhile the machine is running.

" The cleaningarea shouldhave adequate slopes and

drainage to reduce the possibility of a fall due to slipperysurfaces°

= Keep water spray away from electric wiring or fatal

electricshockmay resulL

_, DOnotadjust unloader valve to a pressure in excess

ofmachine rating°

_' Do not secure trigger gun in the pull-back (open)

position.

=' Do notby@assany safety device on this machine° o DOnot leave trigger closed for more than 5 minutes

with engine running. This could damage the pump.

• The muffler and engine heat up during operation and

remain hot immediately after shuttingit down° Avoid

contact with a hot muffler or engine or you could be

severelybumed.

• Never allow any part of the body to come in contact with the fluidstream. DO NOT come in contactwitha

fluid stream created by a leak in the high pressure

hose_

o Highpressure streamof fluidthat this equipment can

produce can pieme skin and its undertyingtissues, leadingto sedousinjuryand possibleamputation.

° High pressure spray can cause paint chips or other

particlesto become airborneand fly at highspeeds.

MAINTENANCE AND STORAGE:

=' Operateand storethis uniton a stable surface. =' High pressure hose can develop leaks from wear,

kinking, abuse, etc. Water spraying!from a leak is

capable of injecting material into skin. inspect hose

each time before using it. Check all hoses for cuts, leaks, abrasions or bulging of cover, or dama_]e or

movement of couplings. If any of these conditions

exist, replace hose immediately. Never repair high

pressure hose. Replace it with another hose that meets minimum pressure rating of your pressure

washer.

LOOK FOR THIS SYMBOL TO POINT OUT IMPORI"ANT

SAFETY PRECAUTIONS. IT MEANS "ATTENTIONH! BE- COME ALERT!!! YOUR SAFETY IS INVOLVED."

CONGRATULATIONS on your purchase ofa Sears Crafts- man high pressure washer. It has been designed, engi- neered and manufactured to give you the best possible

dependability and performance. Should you experience any problem you cannot easily

remedy, please contact your nearest Sears Service Cen- tedDepartment or call the 1-800 number listedon the front of this manual. We have competent, welt-trained techni. clans and the proper tools to service or repair this uniL

Please read and retain this manual. The instructionswilt enable you to assemble and maintain your high pressure

washer properly. Always observe the =SAFETY RULES."

MODEL

NUMBER 580,751500

SERIAL NUMBER

DATE OF

PURCHASE ....

THE MODEl.. AND SERIAL NUMBERS WILL BE

FOUND ON A DECAL ATTACHED TO THE PRES- SURE WASHER,,

YOU SHOULD RECORD BOTH SERIAL NUMBER AND DATE OF PURCHASE AND KEEP IN A SAFE PLACE FOR FUTURE REFERENCE,,

MAINTENANCE AGREEMENT ASearsMaintenanceAgreementis availableonthisprod-

uctoContactyournearestSearsstorefor details, CUSTOMER RESPONSIBILITIES

{, Read and observe the safety rules_

= Follow regular schedule in maintaining, caring for and

using your high pressure washer,

=, Follow the instructions under "Customer Responsibili-

ties" and "Storage" sections of this Owner's Manual

PRODUCT SPECIFICATIONS

Pressure Washer Specifications

PUMP PRESSURE FLOW RATE

DETERGENT MIX

DETERGENT RATIO

Adjustable to 1800 ps!

2.5 gpm Use undiluted detergent

Adjustable to 66:!

WATER SUPPLY

TEMPERATURE SUCTION HEIGHT

Not to exceed 140°F

3 FT'. maximum

Engine Specifications

RATED HORSEPOWER

DISPLACEMENT SPARK PLUG: Type:

Set Gap To.

GASOLINE CAPACITY

OIL (20 oz. capac!ty)....

SOLID STATE IGNITION

AIR GAP

12.6 cu. inches Champion RCJ8

or equivalent

0.030 inch (O.76mm)

2 U.S. quarts

SAE 30 weight

0o0125 inch

In the State of California a spark arrestor is required by law (Section 4442 of the California Public Resources Code), Other states may have similar laws_ Federal laws apply on

federal lands.

NOTE: Ifyou equip the engine of your pressure washer with

a spark arrestor muffler, the spark arrestor must be main- tained in effective working order by the owner operator_

You can order a spark arrestor through your Sears Service Center, See Repair Parts section of engine for part num-

berso

TABLE OF CONTENTS

SAFETY RULES ............................................................ 2

PRODUCT SPECIFICATIONS ...................................... 3

ACCESSORIES AND ATTACHMENTS .......................... 5

CONTENTS OF HARDWARE PACK ..................................6

ASSEMBLY ....................................................................... 7-8

OPERATION ................................................................ 9-13

CUSTOMER RESPONSIBILITIES .......................... _4-15

SERVICE AND ADJUSTMENTS .................................. 16

STORAGE .................................................................... 17

TROUBLESHOOTING ......................... _......................... 18

REPLACEMENT PARTS ......................................... 19-29

WARRANTY ................................................................. 29

-A-

Accessories ............... 5

Air Cleaner ............. 9,15

Assembly

Chet".,_Jist................................. 8

Removing from Carton ............... 7

Tools Required ................ 7

Set Up ......................... 7-8

-B-

Before Starting the Engine .._ 11

-C-

Carburetor, ............... 16

Cleaning Tips ............. !3

Customer Responsibilities. 3,14

Changing Oil, engine .............. 15

Changing Oil, pump ................. 16

Checking Oil Level ................. 15

General Recommendations ..... 14

Pressure Washer .................. t4

Replace Spark Plug .............. t 5

Service Ait Cleaner. ............... 15

-E-

Engine Speed ............... 16

-G-

Gun and Wand Assembly., ._ 8, 9

INDEX

m H --

Hardware Pack ............. 6

High Pressure Hose....... 8, 9

-M-

Maintenance

Agreement .......................... 3

Engine ............................... 15

Pressure Washer ................ 14

Pump ......................... 16

-N-

No_le, Adjustable ......... 10

No_le, Optional Turbo ..... 11

Oil

Engine ............................ 12

Pump ............................. 16

Operation

Detergent Application ........... 11

Know Your Pressure Washer ...o. 9

Stopping.......................... 10

To Start Engine ...................... 13

ToTum on Washer ................. 12

Using Adjustable Nozzle .......... 10

Order Parts ........... back page

-p-

Pressure Regulator ......... 10

-R-

Replacement Parts ...... 19-29

-S-

Safety Latch .............. 13

Safety Rules .............. 2

Service and Adjustments o.. 16

Siphoning ............... 13

Specifications ............. 3

Storage

Engine........................... 17

Pressure Washer Pump ......... 17

-T-

Troubleshooting .......... 18

-W-

Warranty ................. 29

ACCESSORIES AND ATTACHMENTS

These accessories and attachments were available when the high pressure washer was purchased,, They are also available at most Sears retail outlets and service centers. Most Sears stores can order these items for you when you provide the model number of your high pressure washer. Some of these accessories may not apply to your pressure

washer°

FLOOR/SIDING

BRUSH KIT

ROTATING BRUSH

KIT

UTILITY BRUSH KIT

18" STAINLESS

STEEL EXTENSION

ELECTRIC TURBO

NOZZLE

ANGLE EXTENSION

KIT

1/4" ID., 25 ft. EXTENSION

HOSE

HIGH PRESSURE

HOSE QUICK. CON-

NECT KIT

ACCESSORY

QUICK CONNECT

3/8" I,,D,50 It. EXTENSION

HOSE

HIGH PRESSURE

HOSETO HOSE

COUPLING

CHEMICAL INJECTION

FOAMER

' TURBO NOZZLE

1800 PS! (max,)

ACCESSORY

QUICK CONNECT

STARTER KIT

TURBO NOZZLE

2200 AND 2500 PSI (max,)

MULTI-PUR-

POSE/HOUSE

WASH

GARDEN HOSE

QUICK CONNECT

WITH 2 ADAPTORS

tC;

DECK WASH

VEHiCLE/BOAT

WASH

PRESSURE

GAUGE

DEGREASER

CONTENTS OF HARDWARE PACK

Parts packed separately in carton

Parts Carton

Main Unit

Gun and Wand Assembly (packed in flat carton)

Owner's Manual

Guide Handle Assembly (packed in flat carton)

Parts packed In Parts Carton

High Pressure Hose

(2) Wheels

Detegent Pickup ':

Tube and Filter'

MotQrOit (3)Parts Bags

Pads Bag contents shown full size ,(fasteners) _

(2) Axle Pins

!l[ifiJliirlliiFllIl![fltiiJllr!!tlU

(2) Hex Head Capscrews - M8 x 40tT_

(2) Washers - #10

(2) Lock Washers - 5/8"

(2) Washers - M8

(2) Washers - M12

(6) Flange Nuts-M8

(2) 5/8" JAM Nuts

Pads Bag contents not

shown full size

Wire Support

(2) Support Leg

Assemblies

Parts Bag contents not

shown full size

Quick Connect

(2) Push Nuts - i/2" Adjustable Nozzle

ASSEMBLY

Read these iv,sttuctions and Operator's Manual in its en- tirety before you attempt to assemble or operate your new high pressure washer° Your highpressure washer has, for the most part, been asserr_ed at the factory, except those parts leftunassembted. Before you can operate your new highpressure washer, you must assemble the wheel kitand property connect the high pressure hose.

IF YOU HAVE ANY PROBLEMS WITH THE ASSEMBLY OF YOUR PRESSURE WASHER, PLEASE CALL THE PRESSURE WASHER HELPLINE AT 1-800-_-3136.

TOOLS REQUIRED FOR ASSEMBLY

o Mallet = 2 adjustable wrenches OR the following wrenches:

=, 5/16" (8mm) combination wrench = 1/2" (13mm) combination wrench

- 5/8' (16mm) combination wrench = 11/16" (18mm) combination wrench = 7/8" (22ram) combination wrench = 15/16" (24mm) combination wrench

TO REMOVE PRESSURE WASHER FROM CARTON

=, Remove two boxes marked "PARTS INSIDE" and re-

move the parts contained in both boxes.

= Remove unit with one hand under pump and one hand

under recoil starter.

Refer to Page 6, "Contents of Hardware Pack" for an illustrated listingof allthe items included with yourpressure washer, Become familiar with each piece before assem- bling the pressure washer,, Check all contents against the illustrations on Page & If any parts are missing or dam- aged, call the Pressure Washer Helpline at 1-800-222-

3136,

HOW TO SET UP YOUR PRESSURE WASHER

TO INSTALL THE WHEEL KIT

Installing the wheel kit requires the tools listed, the guide handle and items included in the parts carton°

° Prop upthe engine end of the main unit. This willallow

you to slip each axle pin into the holes provided on the

side ofthe base (Fig 1).

JAM

LOGK1NASHER

JAM NUT

FLAT v

REVERSE ANGLE

FIG. 1

With the axle pin inserted inside the base, grip the end of the axle pin as shown with an adjustable or 15/16"

combination wrench. This will keep axle from spinning as you fasten axle to the base with a 5/8 lock washer,

a 5/8"-18 JAM nut, and an M12 flat washer..

o Place wheels on the axles so the rib side of hub is

against mounting base.

= Retain each wheel to itsaxle pin by tapping a push nut

onto end of axle with a mallet.

° Attach support legs to base as shown in Fig, 2 with M8

x 20mm hex head capscrews and flange lock nuts,. Tighten with 13mm or 1/2-inch wrench on each fas-

tener.. Be sure legs are straight when you are tinished_

• Attach the guide handle to the base as shown in Fig, 2 with two M8 x 40mm hex head capscrews, two M8 washers and two flange nuts.

Installingthe Handle

GUIDE

HANDLE

WASHER

CAPSCREW

WIRE SUPPORT

CAPSCREW

_NUT

Installing Support Legs

CAPSC

FIG. 2

ASSEMBLY

o Attach wire support to guide handle with #10 self-dd!l-

in_! screws and #10 fiat washers (Fig° 3). The hose mlnder should be to the left and gun holder to the d_tht.

Be sure loop of support is pointingupward. Place vinyl

cap onto gun holder.

VINYL CAP i /

SUPPORT

FIG. 3

WIRE SUPPORT

FASTENERS

TO ASSEMBLE REMAINING COMPONENTS IMPORTANT: YOU MUST ASSEMBLE WAND AND AT-

TACH ALL HOSES BEFORE YOU START ENGINE,. STARTING ENGINE WITHOUT ALL HOSES CON-

NECTED AND WATER SUPPLIED WILL DAMAGE

PUMP°

Remove cap from top of pump and insert oil fill

cap included inparts bag

(Fig 4).

Remove male connector to inspect Intake Supply Screen in water inlet for cleanliness and inspect Inlet Screen on female connector. Reattach male connector to water inlet and attach female connector to garden

hose.

o Unravel high pressure hose, remove protective cap

from end of hose and check that threads are properly covered withteflon tape° Iftape isnot properly applied,

reapply it so threads are fully covered. The tape seals

the connection from hose to gun and wand assembly°

. Attachfitting withteflon tape to gun andwand assembly

(Fig° 6). You may want to spin gun or spin hose to

secure connection. Tighten with adjustable wrench.

FIG. 6

Attach the other end of the high pressure hose to high

pressure fitting on pump (Fig° 7). Tighten with adjust- able wrench.

DETERGENT PICKUPTUBE

HIGH PRESSURE HOSE

FIG. 4

Included with this unit is a Quick-Connect fitting you

attach to Water Inlet on pump. The quick-connect

includes two parts -- a Male Connector factory-in- sta!led on water inlet and a Female Connector (Fig. 5).

WATER INLET

FEMALE CONNECTOR

MALE CONNECTOR

FIG. 5

FIG. 7

= Attach Detergent Pickup Tube and Filter as shown in

Fig. 7.

= To attach the adjustable nozzle, refer to Operation

section, Fig. 10o;to store optional turbo nozzle, refer to Operation section, Fig. 17.

CHECKLIST

* Check that fasteners you used to install wheels and

handle are tight. Vibration during operation may

loosen fasteners that are not tight enough.

° Check for proper hose connections (high pressure and

water supply) and for tight connections and that there

are no kinks, cuts, or damage to the high pressure hose_

. Provide proper water supply (not to exceed 140°F)_ ,, Be sure to read "Safety Rules" and "Operation" sec-

tionsbefore using the pressure washer.

OPERATION

KNOW YOUR HIGH PRESSURE WASHER READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR HIGH PRESSURE WASHER.

Compare the illustrations with your high pressure washer to familiarize yourself with the locations of various controlsand adjustments. Save this manual for future reference,_

SPARK PLUG

DETERGENT PICKUP TUBE

AND RLTER

HIGH PRESSURE HOSE

OIL RLL OPENING

PRESSURE REGULATOR

GUIDE HANDLE

GUN AND WAND ASSEMBLY

ENGINE ON/OFF CONTROL

CUP FOR WAND

INLET

FEMALE CONNECTOR

QUICK-CONNECT

WIRE SUPPORT t

HIGH PRESSURE €

GASOLINE CA!

FIG. 8

RECOIL STARTER

PUMP -- Develops high pressure, PRESSURE REGULATOR -- Allows you to adjust the

pressure of the outlet stream ENGINE ON-OFF CONTROL -- Sets engine in starting

mode for recoil starter; turns OFF runningengine. RECOIL STARTER -- Used for starting the engine man-

uallyo AIR CLEANER - Dry type filter element limits the amount

of dirt and dust that gets in the engine. GUN AND WAND ASSEMBLY-- Controls the application

ofwater ontocleaning surface with triggerdevice° Includes

safety latch.

HIGH PRESSURE HOSE -- Connect one end to water

pump and other to spray wand.

INTAKE SUPPLY FILTER -- Filters inlet water supply. DETERGENT PICKUP TUBE AND FILTER --Mixes water

and detergent in outlet water flow.

HIGH PRESSURE OUTLET -- Connection for high pres-

sure hose. QUICK-CONNECT -- Easy connection for intake water

supply.

OPERATION

HOW TO USE YOUR WASHER

IF YOU HAVE ANY PROBLEMS OPERATING YOUF.. PRESSURE WASHER, PLEASE CALL THE PRESSURE

WASHER HELPLINE AT 1-800-222-3136. STOPPING YOUR PRESSURE WASHEF_

_; First, move engine throttle lever to °OEW position(Fig

9).

OFFr-]IDLE FAST

-J

FIG. 9

Simply shutttng OFF engine will not release pres- sure in the system. Pullthe trigger onthe spray wand assembly to relieve the pressure in the hose.

NOTE: A small amount of water will squirt out when you release the pressure,

SPRAY NO77LES

Your high pressure washer comes equipped with an adjust- able nozzle (Fig. 10). Attach nozzle as shown in Fig. 10 and HAND TIGHTEN the plastic knob Figure 11 shows the optional turbo nozzle.

HOW 'TO USE ADJUSTABLE NOZZLE

WARNING: NEVER ADJUST SPRAY PATTERN WHEN SPRAYING. NEVER PUT HANDS IN FRONT OF SPRAY NOZZLE TO ADJUST SPRAY PAT-

TERN,

, _=." _,_;_:

FIG. 10

"OPTIONAL TURBO NOZZLE

FIG. 11

With theadjustable nozzle you can adjust the spray pattem to be either high pressure or low pressure, You can also

adjust the spray so it isconcentrated in a stream pattern or

expanded into a fan pattern Use this nozzle to apply detergent

_:sr _'_e..-_,-,zz_ attachment torward when you wis!_:. a_jusi the spray to low _ressure mode (Fig° 12). Pus_ the _ozzle backwa_ toachieve high pressure.

,, "rwistir_g the nozzle adjusts the spray pattern from a

narrow stream to an expanded stream.

,, You can also adjust the pressure by turning the pres-

sure control knob (Fig., 13) to the desired pressure setting. Turning this knob all the way clockwise pro- duces the highest pressure. Do not unscrew the pres-

sure control valve more than 3 tunis. It will come off

FIG. 13

NOZZLE IN HIGH PRESSURE MODE

}:. •

t'-.. '-' '

P_,JSH NOZZLE FORWARD gOF

LOW PRESSURE MODE AND DE- TERGENT APPLICATION

._WISTNOZZLE TO EXPAND SPRAY

T_;IST /

NOZZLE TO NARROW

SPRAY STEAM

FIG_ 12

OPERATION

DETERGENT APPUCATION WITH ADJUSTABLE NOZ21JE

IMPORTANT: USE SOAPS DESIGNED SPECIFICALLY FOR PRESSURE WASHERS. HOUSEHOLD DETER- GENTS COULD DAMAGE THE PUMP°

IMPORTANT: YOU MUST ATTACH ALL HOSES BE-

FORE YOU START THE ENGINE, STARTING THE EN-

GINE WITHOUT ALL THE HOSES CONNECTED WILL

DAMAGE THE PUMP. Pressure washers are useful cteaning tools designed to

clean almost any surface in two easy steps+

= The flint step involves applying an appropriate deter-

t/€_etVentsolution to penetrate and loosen grime.

tergent is applied at low pressure to avoid

splashing, overspraying and wastp..Leaveme .soButton on surface for 3 to 5 minutes to allow somtionto WORK.

o The second step involves cleaning the surface you

have prepared with the pressure washer and then rinsing it clean+

To apply detergent follow these steps:

o Hook up water supply (Fig° 16). o Adjust nozzle to select high pressure mode_

NOTE: Detergent will not flow when in the high pressure

mode_

o Start washer and work from the top of the surface to

the bottom+

NOTE: The high pressure mode is most effective when the tip of the wand is held between 8 inches to two feet from

the surface being cleaned.

QUICK+CONNECT

WATER SUPPLY

,, Prepare your detergent

soluUon as required by yourjob.

,, Place small filter of the

clear, detergent siphon- ing tube into the deter- gent container (Fig. 14)+

o Set nozzle to tow pres-

sure mode. Detergent is not siphoned in the high pressure mode (Fig° t2)..

FIG. 14

INCREASE_

o Start washer and apply

detergent to a dry' sur- face, starting from the

bottom and working up.

You can adjust the con-

centration of detergent by tuming the knob on the detergent injector

(Fig_15).

• Turn knob clockwise or

remove siphon from bot-

tle to stop flow of deter- FIG. 15 gent in tow pressure

mode.

NOTE: Detergents are most effective when applied to a dr,/

surface+

PRESSURE WASHING/RINSING

WARNING: BE EXTREMELY CAREFUL IF YOU

MUST USE PRESSURE WAStiER FROM LADDER, SCAFFOLDING OR ANY OTHER RELATIVELY UN- STABLE LOCATION. PRESSURE IN A RUNNING WASHER BUILDS IN THE WAND AS YOU CLIMB. WHEN YOU PRESS THE TRIGGER, THE RECOIL

FROM THE INITIAL SPRAY COULD FORCE YOU TO FALL, OR IF YOU ARE TOO CLOSE TO THE

CLEANING SURFACE, HIGH PRESSURE COULD

FORCE YOU OFF CLIMBING APPARATUS.

FIGo 16

HOW TO USE OPTIONAL TURBO NOZZLE o The rotating turbo nozzle, in essence, expands the

area of the high pressure stream.

e You cannot adjust the spray pattem with this nozzle, o You cannot apply detergent with this nozzle,,

STORING NOZZLES A holder for the nozzles is included on the base,+ You can

keep the adjustable nozzle in this holder (Fig. 17) or even the optional turbo nozzle.

OPTIONAL TURBO NOZZLE

FIG. 17

BEFORE STARTING THE ENGINE

To operate the engine you will need the following:

ENGINE OIL

IMPORTANT: ANY ATTEMPT TO CRANK OR START

THE ENGINE BEFORE iT HAS BEEN PROPERLY SERV-

ICED WITH THE RECOMMENDED OIL RESULTS IN AN ENGINE FAILURE,

A 27 oz.,bottle of SAE 30 weight oil is included in the parts carton,,

OPERATION

GAS

NOTE: When adding oil to the engine crankcase in the future, use only high quality detergent oil rated with API service classification SF, SG or SH rated SAE 30 weight. Use no special additives. Select the oil's viscosity grade according to your expected operating temperature.

Although mutti-viscosity oils (5W30, 10W30, etc.) improve

starting in coldweather, these multi-viscosityoils will result in increased oil consumption when used above 32°F.

Check your engine oil level more frequently toavoid possi- ble damage from running low on oiloOil sump capacity is

20 ounces.

• Position pressure washer so engine islevel. . Clean area around oil fill plug and remove oil fill plug

(Fig. 18)_.

I_G. 18

° Fill oil crankcase to point of overflowing. Oil sump

capacity is 20 U.S_ ounces..

IMPORTANT: THE MOTOR OIL INCLUDED IN THE CARTON CONTAINS 27 OUNCES. IT IS NOT NECES- SARY TO USE THE ENTIRE AMOUNT OF OIL IN THE OIL CONTAINER°

WARNING: NEVER FILL FUEL TANK INDOORS.

NEVER RLL FUEL TANK WHEN ENGINE IS RUN- NING OR HOT. DO NOT SMOKE WHEN FILLING FUEL TANK.

WARNING: NEVER FILL FUEL TANK COM- PLETELY FIJLL FILL TANK TO ABOUT 1/2" BE- LOWTHE BOTTOM OF FILLER NECKTO PROVIDE SPACE FOR FUEL EXPANSION. WIPE AWAY ANY FUEL SPILLAGE FROM ENGINE AND EQUIPMENT BEFORE STARTING.

The manufacturer recommends fresh, clean, unleaded

regular automotive gasoline with a minimum of 77 octane (Leaded regular grade is an acceptable substitute). Tank

capacity is 2 U,S. quarts.

* Use clean fuel and store in approved, clean covered

containers_ Use clean fill funnets_ Never use "stale"

asoline left over from last season or gasoline stored

r long periods.

IMPORTANT: IT IS IMPORTANT TO PREVENT GUM DEPOSITS FROM FORMING IN ESSENTIAL FUEL SYS- TEM PARTS SUCH AS THE CARBURETOR, FUEL FIL-

TER, FUEL HOSE OR TANK DURING STORAGE. ALSO,

EXPERIENCE INDICATES THAT ALCOHOL-BLENDED FUELS (CALLED GASOHOL OR USING ETHANOL OR METHANOL) CAN ATTRACT MOISTURE WHICH LEADS

TO SEPARATION AND FORMATION OF ACIDS DURING STORAGE. ACIDIC GAS CAN DAMAGE THE FUEL SYS- TEM OF AN ENGINE WHILE IN STORAGE. TO AVOID

ENGINE PROBLEMS, THE FUEL SYSTEM SHOULD BE

EMPTIED BEFORE STORAGE OF 30 DAYS OR

LONGER. SEE "STORAGE" ON PAGE 17. NEVER USE

ENGINE OR CARBURETOR CLEANER PRODUCTS IN THE FUEL TANK OR PERMANENT DAMAGE MAY OC- CUR.

,, Clean area around fuel fill cap, remove cap.

. Add "UNLEADED" regular gasoline, slowly, to fuel

tank.

* Install fuel cap and wipe up any spilled gasoline. TO TURN ON WASHER

* Attach one end of a garden hose toa cold water source=

Water supply should not exceed 140°F (55°C)_

= Check that high pressure hose is attached to pump

outlet and that water supply is attached to pump inlet (plastic fitting)_

= Turn ONwater_

* Press trigger on gun and wand assembly to force air

from high pressure hose.

= Start engine according to "TO START ENGINE."

OPERATION

TO START ENGINE

IMPORTANT: DO NOT RUN PUMP WITHOUT THE

WATER SUPPLY CONNECTED AND TURNED ON. YOU

MUST FOLLOW THiS CAUTION OR THE PUMP WILL, BE DAMAGED_

o Press trigger on pressure washer wand to relieve high

pressure and/or purge the inlet hose of air°

o Move engine control lever to CHOKE position (Fig. 19).

IDLE FAST

]

FIG. 19

Move throttle control to FAST position.

Press tdgger and releaseto relieve pressure in system.

Adjust safety latch to the ON position. This disables the trigger so you cannot inadvertently actuate a high

pressure spray (Fig° 20)°

FIG. 20

• Grasp the engine starter recoil handle and pul! back slowly until you feel some resistance. Then pull rope rapidly to overcome compression, prevent kickback and start engine° Let rope return slowly (Fig. 21)_ °

° When engine starts,move choke lever to "RUN" posi-

tion and throttle control to "FAST" position. If engine fails to start, move choke lever to "RUN" position and °

pull starter rope (max. 2 pulls)_

° if engine fails to start, repeat the process up to three ,_

times, then check the Troubleshooting Chart.

FIG. 21

NOTE: The engine is equipped with low oi! level shutdown system. The engine will not start unless the oil crankcase

is filled to proper level. If engine shuts down during opera- tionor you have difficulty starting the engine, check crank- case oil level and add oil if required°

= Once engine has started, place Safety Latch on spray

gun in OFF position_

,, Press trigger on gun and wand assembly. Water

should spray out the nozzle.

= Adjust no_le for correct pressure, spray angle. You

can also turn the pressure control knob to the desired pressure setting_

o Your pressure washer is ready to user

SIPHONING

We recommend that you DO NOT siphon your water sup-

plyoConnect only to household water supply.

TIPS

= Initially clean an area and then check the surface for

damage, if no damage is found, you can assume it is

okay to continue cleaning Detergents work best when

applied to dry surface,

,, For most effective cleaning, keep spray nozzle be-

tween 8 to 24 inches of cleaning surface.

o Allow the detergent to soak in between 3-5 minutes

before washing and rinsing

= For cleaning, startat lower portion ofarea tobe washed

and work upward, using long, even overlapping strokes.

= For rinsing, push the nozzle sleeve to high pressure

and wait for detergent to clear. Start at the top of area to be rinsed, working down with the same action as for cleaning..

o Never use the garden hose inlet to siphon detergent or

wax,

If you get the spray nozzle too close, especially using high pressure mode, you may damage the cleaning surface_

if you have the spray nozzle too far away, the cleaning will not be as effective.

Do not get closer than 6 inches when cleaning automo -

bite tires.

CUSTOMER RESPONSiBiLiTiES

, i i ii ,,Jiiiiiiil,,,,Jl,i

MAINTENANCE SCHEDULE

FILL IN DATES AS YOU COMPLETE

REGULAR SERVICE

Every25

Before Hoursor

MAINTENANCE TASK .... EachUse.......Yearly

PRESSURE WASHER

Check/deaninletfillerandscreen _ Xt ..................

Checkhighpressurehose. X

,,,,,,,,......

Checkdetergenthose. X Checkgunand wand forleaks. X

HOURLY OPERATING INTERVAL

Every100

AfterFirst Hoursor SERVICE

DATES

50 Hours Yearly

Changepumpoil X:I:

........ ; ............... i,,

ENGINE Checkoil level. X

Changeengineoil. _ X*

............ r ........

Serviceair cleaner. X"° Replace/deansparkplug. _ X

Prepareforstorage= Prepareunitforstorageifit isto remainidle

Jlongerthan30 days

1"Clean ifclogged.. Replace ifperforated ortorn. :1:Change oil after first 50 operating hours, then after every 100 hours or yearly.

Change oil after first 5 hours, then after evePj 25 hours.

* Change sooner=when operating under heavy load or high ambient temperature.

GENERAL RECOMMENDATIONS

The warranty of the high pressure washer does not cover items that have been subjected to operator abuse or neg- ligence_ To receive full value from the warranty, operator must maintain high pressure washer as instructed in this manual,.

Some adjustments will need to be made pefiodicaUy to properly maintain your' high pressure washer,

All adjustments in the Service and Adjustments section of this manual should be made at least once each season.

Once a year you should replace the spark plug and

clean or replace the air falter and check the gun and wand assembly for wear_ A new spark plug and clean air filter assure proper fuel-air mixture and help your engine run better and last longer..

BEFORE EACH USE

,, Check engine oil level.

° Check water inlet filter and quick-connect screen for

damage... ° Check high pressure hose for leaks_ ° Check detergent inlet hose and filter for damager

,, Check gun and wand assembly for leaks_

PRESSURE WASHER MAINTENANCE

,_ DANGER: WATER SPRAYING FROM A LEAK iS t

CAPABLE OF INJECTING MATERIAL INTO SKIN. I NEVER REPAIR HIGH PRESSURE HOSE. RE-I PLACEWITH HOSE THAT MEETS MINIMUM PRES- I SURE RATING OF YOUR PRESSURE WASHER. j

Check Inlet Filter and Screen: Remove quick-correct and examine inletscreenonthe femaleo0nnectorandfilteror1pump

inlet fit_ng, Clean if either is dogged or replace if either is tom. Check High Pressure Hose: High pressure hose can

develop leaks from wear', kinking, abuse., Inspect hose each time before using it, Check for cuts, leaks, abrasions or bulging of cover, or damage or movement of coupfings_ If any of these conditions exist, replace hose immediately°

Check Detergent Hose: Examine the filter on the deter- gent hose and clean if clogged. Hose should fit tightly on barbed fitting. Examine hose for leaks or tears. Replace the filter or hose if either isdamaged_

Check Gun and Wand: Examine hose connection to gun and make sure it is secure_ Test trigger by pressing it and making sure it springs back intoplace when you release it.

Put safety latch in ON position and test trigger° You should

not be able to press trigger.

Check Pump Oil: Refer to PUMP MAINTENANCE for information.,

CUSTOMER RESPONSNBHUTY

PUMP MAINTENANCE

I: WARNING: DO NOT ATTEMPTTO DISASSEMBLE

THE PUMP. WITHOUT THE PROPER TECHNIQUE,

ATTEMPTING TO DISASSEMBLE PUMP MAY CAUSE PERSONAL INJURY. FOR SERVICE,CON- SULT A SEARS AUTHORIZED SERVICE CENTER OR CONTACT YOUR PLACE OF PURCHASE.

Pump Oih Change pump oil after first 50 hours of opera-

tion. To change pump oil, follows these steps: o Place a proper container beneath the pump (Fig, 22).

OIL D_RAIN PLUG

FOR PUMP

FIG. 22

o Remove the Oil Fill Plug on bottom of pump and drain

oil into the container.

= When oil has drained completely, reinstall oil drain

plugo

o Remove pump's oil fill plug, insert funnel and add

recommended SAE 80W-90 oil until level reaches full mark on gauge located on side of the pump Capacity is9 ounces (260ml)_

= Reinstall the pump's oil fill plug.

Purge Pump of Air and Containments:

To remove the air from the pump, follow these steps:

o Set up the pressure washer as described in the AS-

SEMBLY section and connect the water supply. o Remove the nozzle attachment from the gun° o Pull the triggeron the gun and hold

To remove the containments from the pump, follow these steps: = Set up the pressure washer as described in the AS-

SEMBLY section, connect the water supply and start

the engine according to instructions in the OPERA-

TION section.

= Remove the nozzle attachment from the gun_ = Pull the trigger on the gun and holdo

o When the water supply is steady and constant, you may

refasten the nozzle attachment and start the pump.

ENGINE MAINTENANCE

CHECKING OIL LEVEL

See "PREPARATION BEFORE USE" for informationon

checking oil level Oil level should be checked priorto each use or at least ever]/5 hours of operation,. Keep oil level maintained..

CHANGING OIL

Change oil after first 5 hours of operation,. Change oil every 25 hours thereafter,. If you are using your pres* sure washer under extremely dirty or dusty conditions, or in extremely hot weather, change oil more often.

Change oil while engine is still warm from running, as

follows:

/_ CAUTION: DISCONNECT SPARK PLUG WIRE 1

FROM SPARK PLUG AND KEEP IT AWAY FROM SPARK PLUG.

Clean area around oil drain plug, remove plug and drain oil completely into a suitable container (Fig.. 23).

FIG. 23

o When all oil has drained, install and tighten oil plug.. = Clean area around oil fill plug and remove oil fill plug.. ° Fill engine crankcase with recommended oil until oil

level is at point of overflowing. About 20 ounces is required, POUR SLOWLY.

° When engine crankcase is filled to proper level, install

and tighten oil fill plug.

SERVICE AIR CLEANER Your engine will not run properly and may be damaged if

you run it using a dirty air cleaner. Clean or replace the air cleaner paper filter once every 100

hours of operation or once a year, whichever comes first. Clean or replace more often ifoperating under dusty or dirty conditions. Replacements are available at your local Sears Authorized Service Center.

To clean or replace air cleaner (Fig. 24 on Page t6):

= Loosen cover screws (these need not be removed) and

remove cover. Thoroughly clean inside of base and

cover.

CUSTOMER RESPONSIBiLiTiES

AIR CLEANER

FIG. 24

Keep dirt and combustible debris off of muffler area,

CLEAN OUT: CHAFF AND

DIRT

o Service cartridge by tapping gently on a flat surface.

Replace if dirty° Do not oil cartridge.

o Insert cartridge (new or used) and reassemble cover to

base as it was removed before. Tighten cover screws securely.

CLEAN COOLING SYSTEM = Clean dirt or chaff from finger' _luardor rotating screen

every 8 hours to prevent engine damage caused by overheating (Fig..25)°

FIG. 25

REPLACE SPARK PLUG

Change the spark plug every 100 hours of operation or once each year, whichever comes first. This will help engine to start easier and run better. See pressure washer specifications for the type of spark plug you need,. Spark plug gap is 0.030 inch (0.76ram).

SERVICE AND ADJUSTMENTS

FINAL ADJUSTMENT

ENGINE ADJUSTMENTS

Carburetor=

Differences in fuel, temperature, altitude or load may re- quire minor carburetor' adjustment. Air cleaner and air cleaner cover must be assembled to carburetor before starting engine.

INmAL ADJUSTMENT = Gently turn NEEDLE VALVE (Fig,, 26) clockwise untilit

justcloses_Valve may be damaged by turningit inward too far..

° Next open NEEDLE VALVE I-1/2 turns counterclock-.

IDLE SPEED THROTTLE

ADJUSTING SCREW STOP

THROTTLE NEEDLE VALVE

FIG. 26

wise,.

This initial adjustment will permit the engine to be started and warmed up

Start engine and let it warm up for at least five minutes_ With engine running, turn NEEDLE VALVE inward

(clocle_ise - lean mixture) until engine just starts to slow.

ENGINE SPEED

i WARNING: NEVER TAMPER WITH ENGINE GOV-

_" ERNOR WHICH IS FACTORY SET FOR PROPER

ENGINE SPEED. OVERSPEEDING ENGINE

ABOVE FACTORY HIGH SPEED SETTING CAN BE

DANGEROUS.

NOZZLE MAINTENANCE

If the nozzle becomes restricted or clogged with foreign materials, such as dirt, excessive pump pressure may develop. A partially clogged nozzle can cause a pulsing sensation during use° This generally is not a pump related problem, but rather a clogged or partially restricted nozzle,

If the nozzle becomes clogged or partially restricted, imme- diately clean the nozzle with the kit included with your pressure washer by following these instructions:

, Shut off the engine and turn off the water supply, ° Separate the wand from the gun. ° Remove nozzle from the end of the wand using a 2mm

or 5/64 allen wrench (like the one included in the kit).

,, Use ttle wire included in the kit (Fig° 26 on Page 17) or

a small paper clip to free the foreign materials clogging or restricting the nozzle..

SERVICE AND ADJUSTMENTS

FIG. 26

Remove additional debris by back flushing water sup- ply through wand. Back flush between 30 to 60 sec-

onds,.Turn wand to stream spray and move nozzle from

low to high while flushing. Reinstall nozzle into the wand,, DO NOT overtighten,

Reconnect the wand to the gun Reconnect the water supply, turn on the water, and

start the engine.. Test the pressure washer by operating with nozzle in

the high and in the low position.

STORAGE

AFTER EACH USE

Water should not remain in the unit for long periods of time..

Sediments of minerals can deposit on pump parts and "freeze" pump action. Follow these procedures after every

use:

Flush detergent hose by placing, the injector filter into

a pail of clear water while running Pressure Washer with nozzle in low pressure mode° Flush for five min- utes,,

Shut off the engine and let it cool, then remove awl hoses.

A CAUTION; BESURE THE THROTTLE LEVER ISIN

. "STOP" POSITION BEFORE YOU CONTINUE. IF

YOUSTART THE ENGINE WITHOUTTHE PROPER WATER SUPPLY CONNECTED, YOU CAN DAM- AGETHE PUMP.

o Empty the pump of all pumped liquids by pulling recoil

handle about 6 times, This should remove most ofthe

liquid in the pump.

o Coil the high pressure hose and inspect it for damage.

Cuts in the hose or fraying of itcould result in leaks and loss ofpressure° Should any damage be found, replace the hose. DO NOT attempt to repair a damaged hose and use it. Replace the hose with the genuine Crafts-

man part_

,, Drain water from hose and properly hang it on the wire

support provided on the guide handle,

NOTE: To protectthe unitfrom freezing temperatures,you can

drawwindshieldwasherfluid intothepumpby pouringthewasher fluid into a 3-footsectionof garden hose connectedto the inlet adapterand pullingtherecoilhandletwice..

° Store in a clean, dry area°

LONG TERM STORAGE

WARNING: NEVER STORE ENGINEWITHFUEL IN

TANK INDOORS OR INENCLOSED, POORLYVEN- TILATED AREAS WHERE FUMES MAY REACH AN

OPEN FLAME, SPARK OR PILOT LIGHT AS ON A

FURNACE, WATER HEATER, CLOTHES DRYER

OR OTHER GAS APPLIANCE.

Ifyou do not plan to use the Pressure Washer for more than

30 days, you must prepare the engine for long term storage..

NOTE: As always, prepare the pressure washer pump as you would after each use_

It is important to prevent gum deposits from forming in essential fuel system parts such as the carburetor, fuel filter, fuel hose or tank during storage° Also, experience

indicates that alcohol..blended fuels (called "gasohol" or

using ethanol or methanol) can attractmoisture whichleads

to separation and formation of acids during storage. Acidic

gas can damage the fuel system of an engine while in

storage

To avoid engine problems, the fuel system should be

emptied before storage of 30 days or longer. Followthese

instructions:

Protect Fuel System: Engines stored over 30 days need

to be protected or drained of fuel to prevent gum deposits

from forming infuel system oron essential carburetor parts°

,, For engi,_e protection use a fuel stabilizer (such as

STA-BIL'_')oMix stabilizer with fuel in fuel tank and run engine for short time to circulate stabilizer through carburetor.

,_ If you did use "gasohot", run engine until engine stops

from lack of fuelo Make sure you have water supply to pump inlet connected and turned ON,.

Change Oil: While engine is still warm, drain oil from

crankcase. Refill with recommended grade°

Oil Cylinder Bore: Remove spark plug and pour about 1/2

ounce (15ml) of engine oil into the cylinder. Cover spark

plug hole with rag_ Crank slowly to distribute oil.

i _ CAUTION, AVOIDSPRAYFROM SPARKPLUG I

HOLE WHEN CRANKING ENGINE SLOWLY.

° Install spark plugo Do not connect spark plug wire.

OTHER

,_ Do not store gasoline from one season to another. o Replace your gasoline can if your can starts to rusL

Rust and/or dirt in your gasoline will cause problems°

= If possible, store your unit indoors and cover it to give

protection from dust and dirt..

o Cover your unit with a suitable protective cover that

does not retain moisture°

TROUBLESHOOTING

CAUSE CORRECTION

Nozzle in low pressure mode, 1,,

PROBLEM

Pumphasfollowingp_oblems: 1. failureto pn_uce pressure,erratic

pressure,chattering,lossof pressure, 2_ lowwatervolume. 3.

4o 5o

6. 7_

9_ 10, 11_

12.

Detergentfails to mixwithspray, 1.

Engine runs good at no-load but "bogs

Enginewillnotstart;or starts

and runsrough

Engine shuts down duringoperation

Low regulator pressure Water inlet is blocked.

Inadequate water supply inlet hose is kinked or leaking Clogged inlet hose strainer.

Detergent line is not submerged. Water supply is over t40°F. Outlet hose is blocked or leaks. Gun leaks., Nozzle is obstructed.

Pumpisfaulty°

Detergentline Is notsubmerged. Chemicalfilter is clogged Nozzleis inhighpressuremode

Enginespeedistooslowo

1. Low oil level

2. Dirty air cleaner

3. Out of gasoline.

4. Stale gasoline,,

5,_ Spark plug wire not connected

to spark plug 6_ Bad spark plug. 7,, Water in gasotine_

80vemhoking 9 Excessively rich fuel mixture.

10o Intake valve stuck open or closed. 11o Engine has lost compression.

1, Out ofgasoline,,

2. Low oil level,.

Pull nozzle backwardfor high pressuremode.

2_ Adjustrogutatortodesiredsetting,

3. Clear inlet

4. Provideadequate waterflow. 5o Straighteninlethose,patchleak.

6o CheckandcleanInlethosestrainer.

7. Submergedetergent line.

8. Providecoolerwater supply.

9. Clear blocks inoutlethose_

10 Replacegun. 11_ Clear _],

12, ContactSearsServiceDepartment,

1. Insert chemical line intodetergent,. 2, Clean or replace filter/deteq;tent line.

& Push nozzle forward for

low pressure mode,

Contact Sears Service DepadrnenL

1. Fill crankcase to proper level.

2, Clean or replace air cleaner.

3. Fill fuel tank.

4, Drain gas tank; fill with fresh fuel.

5. Connect wire to spark plug.

6,, Replace spark plug. 7,, Drain gas tank; fillwith fresh fuel. 8 Open choke full'>,and crank engine_ 9 Contact Sears Service Department.

10o Contact Sears Service Department,

11. Contact Sears Service Department,

1. Fillfuel tank.

2o Fill crankcasetoproperlevel.

Engine lacks power,_

Engine "hunts" or falters.

Dirty air filter.

Choke is openedtoosoon.,

Replace air filter,

Move choke to halfway posffion until engine runs smoolhly_

+ 42 hidden pages

Craftsman 580.751500 Owner's Manual

Specifications and Main Features

Frequently Asked Questions

User Manual