Craftsman 486243223 Owner’s Manual
Owner's Manual
CAST SPREAD
Model No. 486.243223
®
DO NOT RETURN TO STORE
For Missing Parts or Assembly
Questions Call 1-866-576-8388
CAUTION:
Before using this product,
read this manual and follow
all Safety Rules and
Operating Instructions.
Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.
www.sears.com/craftsman
,, Safety
,, Assembly
,, Operation
,, Maintenance
,, Parts
FORM NO. 40986 (12/03/07)
SAFETY RULES .......................................................... 2
HARDWARE PACKAGE CONTENTS ......................... 3
CARTON CONTENTS ................................................. 3
ASSEMBLY ............................................................... 4-6
OPERATION ................................................................ 7
MAINTENANCE .......................................................... 8
STORAGE ................................................................... 8
NOTES ................................................................... 9-10
REPAIR PARTS ....................................................... 11
PARTS ORDERING/SERVICE ..................... Back Page
LIMITED ONE YEAR WARRANTY ON CRAFTSMAN SPREADER
For one year from the date of purchase, when this spreader is maintained and lubricated according to the operating
and maintenance instructions in the owner's manual, Sears will repair any defect in material or workmanship free of
charge. If this spreader is used for commercial or rental purposes, this warranty applies for only 90 days from the date of
purchase.
This warranty does not cover repairs necessary because of operator negligence or abuse, including the failure to maintain
the equipment according to instructions contained in the owner's manual.
WARRANTY SERVICE IS AVAILABLE BY CONTACTING THE NEAREST SEARS SERVICE CENTER/DEPARTMENT
IN THE UNITED STATES.
This warranty applies only while this product is in the United States.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Sears, Roebuck and Co. D/817 WA. Hoffman Estates, Chicago, IL 60179
The model number and serial numbers will be found on a
decal attached to the spreader.
You should record both the serial number and the date of
purchase and keep in a safe place for future reference.
Read the towing vehicle owners manual and towing
vehicle safety rules. Know how to operate your tractor
before using the broadcast spreader attachment.
Read the chemical label instructions and cautions for
handling and applying the chemicals purchased for
spreading.
Wear eye and hand protection when handling and
when applying lawn or garden chemicals.
Never operate tractor and spreader attachment
without wearing substantial footwear, and do not allow
anyone to ride or sit on spreader attachment frame.
Never allow children to operate the tractor or spreader
attachment, and do not allow adults to operate without
proper instructions.
MODEL NUMBER:
SERIAL NUMBER:
DATE OF PURCHASE:
Always begin with the transmission in first (low) gear
and with the engine at low speed, and gradually
increase speed as conditions permit. Maximum towing
speed - 6 M.RH.
When towing broadcast spreader do not drive too
close to a creek or ditch and be alert for holes and
other hazards which could cause you to loose control
of the broadcast spreader and tractor.
Before operating vehicle on any grade (hill) refer to
the safety rules in the vehicle owner's manual con-
cerning safe operation on slopes. Stay off steep
slopes!
Follow maintenance and lubrication instructions as
outlined in this manual.
486.243223
Look for this symbol to point out important safety precautions. It means J Attention!! Become alert!! Your safety
is involved.
B
/
J
/ j
F7
L
REF. QTY. DESCRIPTION
A 2 Hex Bolt, 1/4" x 1-1/2"
B 4 Hex Bolt, 1/4" x 1-3/4"
C 4 Hex Bolt, 1/4" x 2"
D 8 Nut, 1/4"
E 1 Hair Cotter Pin, 1/8"
F 3 Plastic Cap
L
/J" K
j.J
REF. QTY. DESCRIPTION
G 1 Agitator Hairpin
H 2 Washer, 1/4"
I 2 Hex Flange Bearing
J 2 Spacer
K 2 Hub Cap
L 1 Hitch Pin
3
/
4
CARTON CONTENTS
1. Hopper
2. Control Cable
3. Frame Tube
4. Impeller Assembly
5. Hitch Tube, R.H. (Right Hand)
6. Hitch Tube, L.H. (Left Hand)
7. Hitch Control Tube
3
10
8. Hitch Brackets (2)
9. Drive WHeel
10. Wheel
TOOLS REQUIRED FOR ASSEMBLY
(2) 7/16" Wrenches
REMOVAL OF PARTS FROM CARTON
• Remove all parts and hardware packages from the
carton. Lay out all parts and hardware and identify
using the illustrations on page 3.
• Insert the two hex flange bearings (I) into the frame
tube. See figure 1.
• Attach the hopper to the frame tube using two 1/4" x
1-1/2" hex bolts (A), 1/4" washers (H), and 1/4" nylock
nuts (D) as shown in figure 3. Tighten.
• Insert the agitator hairpin (G) into the hole at the top
of the impeller. See figure 3.
G
..... A
÷
H
H
FIGURE 3
I
FIGURE 1
• Insert each side of the axle of the impeller assembly
into the frame tube. See figure 2.
Attach the drive wheel (9) to the right (indented) side
of the axle. Secure the wheel in place with a hub cap
(K). See figure 4.
J
K
FIGURE 4
FIGURE 2
4
Loading...