Craftsman 315349720 Owner’s Manual

OPERATOR'S MANUAL

SMRN I

10 in. TABLE SAW

Model No.

315.349720

WARNING: To reduce the risk of injury, the

user must read and understand the operator's manual before using this product.

Customer Help Line: 1-800-932-3188

Product distributed in the United States by Sears Brands Management Corporation Hoffman Estates, IL 601 79 Visit the Craftsman web page: www.sears.com

990000155 6-4-12 (REV:02)

Save this manual for future reference

0( 0s

• Introduction ...................................................................................................................................................................... 2

• Warranty ........................................................................................................................................................................... 2

• General Safety Rules .................................................................................................................................................... 3-4

• Specific Safety Rules .................................................................................................................................................... 4-5

• Symbols ............................................................................................................................................................................ 6

• Electrical ........................................................................................................................................................................... 7

• Glossary of Terms ............................................................................................................................................................. 8

• Features ...................................................................................................................................................................... 9-12

• Tools Needed ................................................................................................................................................................. 12

• Loose Parts .................................................................................................................................................................... 13

• Assembly .................................................................................................................................................................. 14-20

• Operation .................................................................................................................................................................. 21-34

• Adjustments .............................................................................................................................................................. 35-37

• Maintenance ................................................................................................................................................................... 37

• Troubleshooting ........................................................................................................................................................ 38-39

• Illustrated Parts List.................................................................................................................................................. 40-46

• Parts Ordering/Service ..................................................................................................................................... Back Page

This tool has many features for making its use more pleasant and enjoyable. Safety, performance, and dependability have been given top priority in the design of this product making it easy to maintain and operate.

ONE YEAR FULL WARRANTY ON CRAFTSMAN TOOL If this Craftsman tool fails due to a defect in material or workmanship within one year from the date of purchase. Call

1-800-4-MY-HOME ® to arrange for free repair. If this tool is used for commercial or rental purposes, this warranty will apply for only ninety days from the date of purchase. This warranty applies only while this product is in the United States.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Sears, Roebuck and Co., Dept. 817WA, Hoffman Estates, IL 60179

_k WARNING:Read and understand all instruc-

tions. Failure to follow all instructions listed below,

may result in electric shock, fire and/or serious personal injury.

READ ALL INSTRUCTIONS

• KNOW YOUR POWER TOOL. Read the operator's manual carefully. Learn the saw's applications and limitations as well as the specific potential hazards

related to this tool.

• GUARD AGAINST ELECTRICAL SHOCK BY PREVENTING BODY CONTACT WITH GROUNDED

SURFACES. For example, pipes, radiators, ranges,

refrigerator enclosures.

• KEEP GUARDS IN PLACE and in good working order.

• REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting

wrenches are removed from tool before turning it on.

• KEEP WORK AREA CLEAN. Cluttered areas and benches invite accidents. DO NOT leave tools or

pieces of wood on the saw while it is in operation.

• DO NOT USE IN DANGEROUS ENVIRONMENTS. Do not use power tools in damp or wet locations or

expose to rain. Keep the work area well lit.

• KEEP CHILDREN AND VISITORS AWAY. All visitors

should wear safety glasses and be kept a safe distance from work area. Do not let visitors contact

tool or extension cord while operating.

• MAKE WORKSHOP CHILDPROOF with padlocks and master switches, or by removing starter keys.

• DON'T FORCE TOOL. It will do the job better and

safer at the feed rate for which it was designed.

• USE RIGHT TOOL. Don't force the tool or attachment

to do a job it was not designed for. Don't use it for a

purpose not intended.

• USE THE PROPER EXTENSION CORD. Make sure

your extension cord is in good condition. Use only a cord heavy enough to carry the current your product

will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. A wire gauge size (A.W.G.) of at least 14 is recommended for an extension cord 25 feet or less in length. If in

doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord.

• DRESS PROPERLY. Do not wear loose clothing,

gloves, neckties, or jewelry. They can get caught and draw you into moving parts. Rubber gloves and

nonskid footwear are recommended when working

outdoors. Also wear protective hair covering to contain

long hair.

• ALWAYS WEAR SAFETY GLASSES WITH SIDE

SHIELDS. Everyday eyeglasses have only impact-

resistant lenses, they are NOT safety glasses.

• SECURE WORK. Use clamps or a vise to hold work when practical. It's safer than using your hand and frees both hands to operate tool.

• DON'T OVERREACH. Keep proper footing and

balance at all times.

• MAINTAIN TOOLS WITH CARE. Keep tools sharp

and clean for better and safer performance. Follow instructions for lubricating and changing accessories.

• DISCONNECT TOOLS. When not in use, before servicing, or when changing attachments, blades, bits,

cutters, etc., all tools should be disconnected.

• AVOID ACCIDENTAL STARTING. Be sure switch is off when plugging in any tool.

• USE RECOMMENDED ACCESSORIES. Consult the

operator's manual for recommended accessories. The use of improper accessories may risk injury.

• NEVER STAND ON TOOL. Serious injury could

occur if the tool is tipped or if the cutting tool is unintentionally contacted.

• CHECK DAMAGED PARTS. Before further use of the tool, a guard or other part that is damaged should

be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting and any other conditions

that may affect its operation. A guard or other part that

is damaged must be properly repaired or replaced by an authorized service center to avoid risk of personal injury.

• USE THE RIGHT DIRECTION OF FEED. Feed work

into a blade or cutter against the direction of rotation of blade or cutter only.

• NEVER LEAVE TOOL RUNNING UNATTENDED. TURN THE POWER OFF. Don't leave tool until it

comes to a complete stop.

• PROTECT YOUR LUNGS. Wear a face or dust mask if the cutting operation is dusty.

• PROTECT YOUR HEARING. Wear hearing protection

during extended periods of operation.

• DO NOT ABUSE CORD. Never yank cord to

disconnect from receptacle. Keep cord away from heat, oil, and sharp edges.

• WHEN OPERATING A POWER TOOL OUTSIDE, USE AN OUTDOOR EXTENSION CORD MARKED "W-A"

OR "W'. These cords are rated for outdoor use and

reduce the risk of electric shock.

• KEEP BLADES CLEAN, SHARP, AND WITH SUFFICIENT SET. Sharp blades minimize stalling

and kickback.

• KEEP HANDS AWAY FROM CUTTING AREA. Keep

hands away from blades. Do not reach underneath

work or around or over the blade while blade is

rotating. Do not attempt to remove cut material when blade is moving.

• BLADE COASTS AFTER BEING TURNED OFF.

• NEVER USE IN AN EXPLOSIVE ATMOSPHERE.

Normal sparking of the motor could ignite fumes.

• INSPECT TOOL CORDS PERIODICALLY. If damaged, have repaired by a qualified service technician at

an authorized service facility. The conductor with

insulation having an outer surface that is green with

or without yellow stripes is the equipment-grounding conductor. If repair or replacement of the electric cord

or plug is necessary, do not connect the equipment- grounding conductor to a live terminal. Repair or

replace a damaged or worn cord immediately. Stay

constantly aware of cord location and keep it well away from the rotating blade.

• INSPECT EXTENSION CORDS PERIODICALLY and replace if damaged.

• GROUND ALL TOOLS. If tool is equipped with three- prong plug, it should be plugged into a three-hole

electrical receptacle.

• CHECK WITH A QUALIFIED ELECTRICIAN or

service personnel if the grounding instructions are not completely understood or if in doubt as to whether the

tool is properly grounded.

• USE ONLY CORRECT ELECTRICAL DEVICES:

3-wire extension cords that have 3-prong grounding

plugs and 3-pole receptacles that accept the tool's plug.

• DO NOT MODIFY the plug provided. If it will not fit the

outlet, have the proper outlet installed by a qualified

electrician.

• KEEP TOOL DRY, CLEAN, AND FREE FROM

OIL AND GREASE. Always use a clean cloth when cleaning. Never use brake fluids, gasoline, petroleum-

based products, or any solvents to clean tool.

• STAY ALERT AND EXERCISE CONTROL. Watch what you are doing and use common sense. Do not

operate tool when you are tired. Do not rush.

• DO NOT USE TOOL IF SWITCH DOES NOT TURN IT ON AND OFF. Have defective switches replaced by an

authorized service center.

• USE ONLY CORRECT BLADES. Do not use blades with incorrect size holes. Never use blade washers

or blade bolts that are defective or incorrect. The maximum blade capacity of your saw is 10 in.

(254 ram).

• BEFORE MAKING A CUT, BE SURE ALL ADJUSTMENTS ARE SECURE.

• BE SURE BLADE PATH IS FREE OF NAILS. Inspect for and remove all nails from lumber before cutting.

• NEVER TOUCH BLADE or other moving parts during

use.

• NEVER START A TOOL WHEN ANY ROTATING

COMPONENT IS IN CONTACT WITH THE WORKPIECE.

• DO NOT OPERATE A TOOL WHILE UNDER THE

INFLUENCE OF DRUGS, ALCOHOL, OR ANY MEDICATION.

• WHEN SERVICING use only identical replacement parts. Use of any other parts may create a hazard or

cause product damage.

• USE ONLY RECOMMENDED ACCESSORIES listed in this manual or addendums. Use of accessories that

are not listed may cause the risk of personal injury.

Instructions for safe use of accessories are included

with the accessory.

• DOUBLE CHECK ALL SETUPS. Make sure blade is tight

and not making contact with saw or workpiece before connecting to power supply.

• FIRMLY BOLT THE SAW TO A WORK BENCH OR LEG STAND at approximately hip height.

• NEVER OPERATE THE SAW ON THE FLOOR.

• GUARD AGAINST KICKBACK. Kickback occurs

when the blade stalls rapidly and workpiece is driven

back towards the operator. It can pull your hand into

the blade resulting in serious personal injury. Stay out of blade path and turn switch off immediately if blade

binds or stalls.

• USE RIP FENCE. Always use a fence or straight edge

guide when ripping.

• SUPPORT LARGE PANELS. To minimize risk of blade pinching and kickback, always support large panels.

• REMOVE ALL FENCES AND AUXILIARY TABLES before transporting saw. Failure to do so can result in

an accident causing possible serious personal injury.

• ALWAYS USE BLADE GUARD, RIVING KNIFE, AND ANTI-KICKBACK PAWLS on all "through-sawing"

operations. Through-sawing operations are those in

which the blade cuts completely through the workpiece

as in ripping or cross cutting. Keep the blade guard down, the anti-kickback pawls down, and the riving

knife in place.

• ALWAYS SECURE WORK firmly against the rip fence

or miter gauge. NEVER use the rip fence during the

same operation as the miter gauge.

• WHEN MAKING NON-THROUGH RIP CUTS, always

use a push stick, push block, and/or featherboard so

your hands do not come within 3 inches of the saw

blade.

• WHEN RIPPING NARROW STOCK, always use a

push stick, push block, or featherboard.

• NEVERperformanyoperation"freehand"which meansusingonlyyourhandstosupportorguidethe

workpiece.Alwaysuseeithertheripfenceormiter gaugetopositionandguidethework.

• NEVERstandorhaveanypartofyourbodyinlinewith

thepathofthesawblade.

• NEVERreachbehind,over,orwithinthreeinchesof

thebladeorcutterwitheitherhandforanyreason.

• MOVE THE RIP FENCE out of the way when cross

cutting.

• DO NOT USE THE MITER GAUGE AND RIP FENCE

during the same operation.

• NEVER use rip fence as cutoff gauge when cross

cutting.

• NEVER attempt to free a stalled saw blade without first

turning the saw OFF and disconnecting the saw from the power source.

• PROVIDE ADEQUATE SUPPORT to the rear and sides

of the saw table for wide or long workpieces.

• AVOID KICKBACKS (work thrown back toward you) by:

a) Keeping blade sharp. b) Keeping rip fence parallel to the saw blade. c) Keeping riving knife, anti-kickback pawls, and

blade guard in place and operating.

d) Not releasing the work before it is pushed all the

way past the saw blade using a push stick.

e) Not ripping work that is twisted or warped or

does not have a straight edge to guide along the fence.

• IF THE POWER SUPPLY CORD IS DAMAGED, it

must be replaced only by the manufacturer or by an

authorized service center to avoid risk.

• AVOID AWKWARD OPERATIONS AND HAND POSITIONS where a sudden slip could cause your

hand to move into the cutting tool.

• USE ONLY RECOMMENDED ACCESSORIES listed in this manual or addendums. Use of accessories that

are not listed may cause the risk of personal injury.

Instructions for safe use of accessories are included

with the accessory.

• MAKE SURE THE WORK AREA HAS AMPLE LIGHTING to see the work and that no obstructions

will interfere with safe operation BEFORE performing any work using the table saw.

• ALWAYS TURN OFF SAW before disconnecting it, to

avoid accidental starting when reconnecting to power supply.

• ONLY USE BLADES within the thickness range

stamped on the riving knife.

• THIS TOOL should have the following markings:

a) Wear eye protection.

b) Use saw blade guard and riving knife for every

operation for which it can be used, including

all through sawing. c) Keep hands out of the line of saw blade. d) Use a push stick when required. e) Pay particular attention to instructions on reducing

risk of kickback. f) Do not perform any operation freehand.

g) Never reach around or over the saw blade.

h) Never operate saw on floor or below waist height.

• NEVER CUT MORE THAN ONE PIECE OF

MATERIAL AT A TIME.

SAVE THESE INSTRUCTIONS. Refer to them

frequently and use to instruct other users. If you loan someone this tool, loan them these instructions also.

CALIFORNIA PROPOSITION 65

WARNING: This product and some dust created by power sanding, sawing, grinding, drilling, and other

construction activities may contain chemicals, including lead, known to the State of California to cause cancer, birth defects, or other reproductive harm. Wash hands after handling.

Some examples of these chemicals are:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other masonry products and,

• arsenic and chromium from chemically treated lumber.

Your risk from exposure to these chemicals varies, depending on how often you do this type of work. To reduce your exposure, work in a well-ventilated area and with approved safety equipment, such as dust masks that are specially designed to filter out microscopic particles.

Thefollowingsignalwordsandmeaningsareintendedtoexplainthelevelsofriskassociatedwiththisproduct.

SYMBOL SIGNAL MEANING

,_ DANGER:

,_ WARNING:

,_ CAUTION:

NOTICE:

Some of the following symbols may be used on this tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and safer.

SYMBOL

Safety Alert

Read Operator's Manual

Eye Protection

NAME

Indicates an imminently hazardous situation, which, if not avoided, will result in death or serious injury.

Indicates a potentially hazardous situation, which, if not avoided, could result in death or serious injury.

Indicates a potentially hazardous situation, which, if not avoided, may result in minor or moderate injury.

(Without Safety Alert Symbol)) Indicates important information not related to an injury hazard, such as a situation that may result in property damage.

DESIGNATION/EXPLANATION

Indicates a potential personal injury hazard.

To reduce the risk of injury, user must read and understand opera- tor's manual before using this product.

Always wear eye protection with side shields marked to comply with ANSI Z87.1.

@ @

min

,-%,

n o

[]

.../min

No Hands Symbol

Wet Conditions Alert

Volts

Amperes

Hertz

Minutes

Alternating Current

No Load Speed

Class II Construction

Per Minute

Failure to keep your hands away from the blade will result in

serious personal injury.

Do not expose to rain or use in damp locations.

Voltage

Current

Frequency (cycles per second)

Time

Type of current

Rotational speed, at no load

Double-insulated construction

Revolutions, strokes, surface speed, orbits, etc., per minute

EXTENSION CORDS Use only 3-wire extension cords that have 3-prong

grounding plugs and 3-pole receptacles that accept the

tool's plug. When using a power tool at a considerable

distance from the power source, use an extension cord heavy enough to carry the current that the tool will draw.

An undersized extension cord will cause a drop in line

voltage, resulting in a loss of power and causing the motor to overheat. Use the chart provided below to determine the minimum wire size required in an extension cord. Only

round jacketed cords listed by Underwriter's Laboratories

(UL) should be used.

**Ampere rating (on tool faceplate)

0-2.0 2.1-3.4 3.5-5.0 5.1-7.0 7.1-12.0 12.1-16.0

Cord Length Wire Size (A.W.G.)

25' 16 16 16 16 14 14

50' 16 16 16 14 14 12

100' 16 16 14 12 10 --

**Used on 12 gauge - 20 amp circuit.

NOTE: AWG = American Wire Gauge

When working with the tool outdoors, use an extension

cord that is designed for outside use. This is indicated by the letters "W-A" or "W" on the cord's jacket.

Before using an extension cord, inspect it for loose or

exposed wires and cut or worn insulation.

SPEED AND WIRING

The no-load speed of this tool is approximately 5,000 rpm. This speed is not constant and decreases under a load or

with lower voltage. For voltage, the wiring in a shop is as important as the motor's horsepower rating. A line intend-

ed only for lights cannot properly carry a power tool mo-

tor. Wire that is heavy enough for a short distance will be too light for a greater distance. A line that can support one

power tool may not be able to support two or three tools. GROUNDING INSTRUCTIONS

This product must be grounded. In the event of a malfunc- tion or breakdown, grounding provides a path of least

resistance for electric current to reduce the risk of electric shock. This tool is equipped with an electric cord having

an equipment-grounding conductor and a grounding plug.

The plug must be plugged into a matching outlet that is

properly installed and grounded in accordance with all local codes and ordinances.

Do not modify the plug provided. If it will not fit the outlet, have the proper outlet installed by a qualified electrician.

WARNING: Improper installation of the ground-

ing plug can result in a risk of electric shock. When repair or replacement of the cord is required, do

not connect the grounding wire to either flat blade terminal. The wire with insulation having an outer surface that is green with or without yellow stripes is the grounding wire.

WARNING: Keep the extension cord clear of the working area. Position the cord so that it will not get

caught on lumber, tools or other obstructions while

you are working with a power tool. Failure to do so

can result in serious personal injury.

WARNING: Check extension cords before each

use. If damaged replace immediately. Never use product with a damaged cord since touching the damaged area could cause electrical shock resulting in serious injury.

ELECTRICAL CONNECTION

This product is powered by a precision built electric

motor. It should be connected to a power supply that is 120 V, AC only (normal household current), 60 Hz. Do not operate this product on direct current (DC). A substantial voltage drop will cause a loss of power and

the motor will overheat. If the saw does not operate when

plugged into an outlet, double check the power supply.

Check with a qualified electrician or service personnel if

the grounding instructions are not completely understood,

or if in doubt as to whether the tool is properly grounded. Repair or replace a damaged or worn cord immediately.

This product is for use on a nominal 120 volt circuit and

has a grounding plug similar to the plug illustrated in fig- ure 1. Only connect the product to an outlet having the same configuration as the plug. Do not use an adapter with this product.

GROUNDING

120 V GROUNDEDOUTLET

Fig. 1

Anti-Kickback Pawls (flooring, radial arm, and table

saws)

A device which, when properly installed and maintained, is designed to stop the workpiece from being kicked back toward the front of the saw during a ripping operation.

Arbor

The shaft on which a blade or cutting tool is mounted. Bevel Cut

A cutting operation made with the blade at any angle other than 90 ° to the table surface.

Compound Cut

A cross cut made with both a miter and a bevel angle.

Cross Cut

A cutting or shaping operation made across the grain or the width of the workpiece.

Cutterhead (planers and jointer planers)

A rotating cutterhead with adjustable blades or knives. The blades or knives remove material from the workpiece.

Dado Cut

A non-through cut which produces a square-sided notch or trough in the workpiece (requires a special blade).

Featherboard

A device used to help control the workpiece by holding it securely against the table or fence during any ripping

operation.

FPM or SPM

Feet per minute (or strokes per minute), used in reference to blade movement.

Freehand

Performing a cut without the workpiece being guided by a fence, miter gauge, or other aids.

Gum A sticky, sap-based residue from wood products.

Heel

Alignment of the blade to the fence. Kerr

The material removed by the blade in a through cut or the slot produced by the blade in a non-through or partial cut.

Kickback A hazard that can occur when the blade binds or stalls,

throwing the workpiece back toward operator. Miter Cut

A cutting operation made with the workpiece at any angle to the blade other than 90 °.

Non-Through Cuts

Any cutting operation where the blade does not extend completely through the thickness of the workpiece.

Pilot Hole (drill presses)

A small hole drilled in a workpiece that serves as a guide for drilling large holes accurately.

Push Blocks (jointer planers)

Device used to feed the workpiece over the jointer planer cutterhead during any operation. This aid helps keep the operator's hands well away from the cutterhead.

Push Blocks (flooring and table saws)

Device used to hold the workpiece during cutting opera- tions. This aid helps keep the operator's hands well away

from the blade.

Push Sticks (flooring and table saws)

Device used to push the workpiece during cutting opera- tions. A push stick should be used for narrow ripping operations. The aid helps keep the operator's hands well away from the blade.

Resaw

A cutting operation to reduce the thickness of the workpiece to make thinner pieces.

Resin

A sticky, sap-based substance that has hardened.

Revolutions Per Minute (RPM)

The number of turns completed by a spinning object in one minute.

Ripping or Rip Cut

A cutting operation along the length of the workpiece.

Riving Knife (flooring and table saws)

A metal piece, slightly thinner than the blade, which helps keep the kerf open and also helps to prevent kickback.

Saw Blade Path

The area over, under, behind, or in front of the blade. As it applies to the workpiece, that area which will be or has been cut by the blade.

Set

The distance that the tip of the saw blade tooth is bent (or set) outward from the face of the blade.

Snipe (planers)

Depression made at either end of a workpiece by cutter blades when the workpiece is not properly supported.

Through Sawing

Any cutting operation where the blade extends completely through the thickness of the workpiece.

Throw-Back

The throwing back of a workpiece usually caused by the workpiece being dropped into the blade or being placed

inadvertently in contact with the blade.

Workpiece or Material

The item on which the operation is being done. Worktable Surface where the workpiece rests while performing a cutting, drilling, planing, or sanding operation.

PRODUCT SPECIFICATIONS

Blade Arbor .............................................................. 5/8 in.

Blade Diameter .......................................................... 10 in.

Blade Tilt ................................................................. 0° - 45°

Rating ............................................... 120 V, AC only, 60 Hz

Input ..................................................................... 15 Amps

No Load Speed .................................... 5,000 r/min. (RPM)

Cutting Depth at 0° ...................................................... 3 in.

Cutting Depth at 45°.............................................. 2-1/2 in.

MITER

GAUGE

OUTFEED

SUPPORT

ANTI-KICKBACK

PAWLS

FRONT

RAIL

BLADE

RIVING GUARD

KNIFE

RIP

FENCE

SLIDINGTABLE

EXTENSION

LOCKING

LEVER

SCALE

TABLELOCKING

LEVER

STORAGE

BRACKET(S)

BEVEL

LOCKING BEVEL

LEVER SCALE

BLADE

WRENCH

STORAGE

HEIGHT/BEVEL

ADJUSTING

HANDWHEEL

SWITCH

BEVEL

INDICATOR

Fig. 2

KNOWYOURTABLESAW

See Figure 2.

The safe use of this product requires an understanding of the information on the tool and in this operator's manual as well as a knowledge of the project you are attempting. Before use of this product, familiarize yourself with all op- erating features and safety rules.

ANTI-KICKBACK PAWLS - Kickback is a hazard in which the workpiece is thrown back toward the operator. The

teeth on the removable anti-kickback pawls point away from the workpiece. If the workpiece should be pulled back toward the operator, the teeth dig into the wood to help prevent or reduce the possibility of kickback.

BEVEL SCALE - The easy-to-read scale on the front of the cabinet shows the exact blade angle.

BLADE - This saw is provided with a 10 in. carbide blade. The blade is raised and lowered with the height/bevel adjusting handwheel. Bevel angles are locked with the bevel locking lever.

_1_ WARNING: Do not use blades rated less than the

speed of this tool. Failure to heed this warning could result in personal injury.

BLADE GUARD - Always keep the removable blade guard down over the saw blade for through-sawing cuts.

BEVEL LOCKING LEVER - This lever, placed just under the saw table surface on the front of the cabinet, locks the

angle setting of the blade.

HEIGHT/BEVEL ADJUSTING HANDWHEEL - Located on the front of the cabinet, use this handwheel to lower

and raise the blade for height adjustments or blade re- placement. This handwheel also makes the adjustment for bevel angles easy.

MITER GAUGE - The miter gauge aligns the wood for a cross cut. The easy-to-read indicator shows the exact angle for a miter cut.

MITER GAUGE GROOVES - The miter gauge rides in the grooves on the saw table.

OUTFEED SUPPORT - This table extension at the back of the tool gives the operator additional support when cut-

ting long workpieces. RIP FENCE - A sturdy metal fence guides the workpiece

and is secured with the locking handle. RIVING KNIFE - A removable metal piece of the blade

guard assembly, slightly thinner than the saw blade, which helps keep the kerf open and prevent kickback. When in the through sawing, or "up" position, it is higher than the saw blade. When in the non-through sawing, or "down" position, it is below the saw blade teeth.

SCALE - Located on the front rail, the easy-to-read scale provides precise measurements for rip cuts.

SLIDING TABLE EXTENSION - Located on the right side of the saw table, this table extension gives the operator

additional support when cutting wide workpieces. SWITCH ASSEMBLY - This saw has an easy access

power switch located below the front rail. To lock the switch in the OFF position, remove the switch key from the switch. Place the key in a location that is inaccessible to children and others not qualified to use the tool.

OPERATING COMPONENTS

The upper portion of the blade projects up through the table and is surrounded by an insert called the throat plate. The height of the blade is set with a handwheel on the front of the cabinet. To accommodate wide panels, the

saw table has rails on each side. Detailed instructions are provided in the Operation section of this manual for the

basic cuts: cross cuts, miter cuts, bevel cuts, and com- pound cuts.

The rip fence is used to position work for lengthwise cuts. A scale on the front rail shows the distance between the

rip fence and the blade. It is very important to use the blade guard assembly for all

through-sawing operations. The blade guard assembly includes: riving knife, anti-kickback pawls, and plastic blade guard.

SWITCH ASSEMBLY

See Figure 3.

This saw is equipped with a switch assembly that has a built-in locking feature. This feature is intended to prevent unauthorized and possible hazardous use by children and

others.

TO TURN YOUR SAW ON:

• With the switch key inserted into the switch, lift the

switch to turn on ( I ).

TO TURN YOUR SAW OFF:

• Press the switch down to turn off ( O ). TO LOCK YOUR SAW:

• Press the switch down.

• Remove the switch key from the switch and store in a safe, secure location.

WARNING: ALWAYS remove the switch key when the tool is not in use and keep it in a safe place. In the event of a power failure, turn the switch off ( 0 )

and remove the key. This action will prevent the tool from accidentally starting when power returns.

WARNING: ALWAYS make sure your workpiece is

not in contact with the blade before operating the switch to start the tool. Failure to heed this warning may cause the workpiece to be kicked back toward

the operator and result in serious personal injury.

WARNING: To reduce the risk of accidental start-

ing, ALWAYS make sure the switch is inthe off ( 0 ) position before plugging tool into the power source.

SWITCH SWITCH

ON OFF

SWITCHKEY _ /_

SWITCHIN LOCKEDPOSITION

Fig. 3

BLADES

For maximum performance, it is recommended that you use the 10 in. carbide-tipped combination blade pro- vided with your saw. Additional blade styles of the same high quality are available for specific operations such as ripping. Your local dealer can provide you with complete

information. Kerf width must be within the limits stamped on the riving

knife.

The following tools (not included or drawn to scale) are needed for assembly and making adjustments:

WARNING: Do not use blades rated less than the

speed of this tool. Failure to heed this warning could result in personal injury.

FRAMINGSQUARE

COMBINATION

SQUARE

PHILLIPS

SCREWDRIVER

FLATHEAD

SCREWDRIVER

U AND8 mmSOCKET

C-CLAMPS

Fig. 4

Thefollowingitemsareincludedwithyourtablesaw:

A. Anti-Kickback Pawls ............................................... 1

B. Blade Guard ............................................................ 1

C. Miter Gauge ............................................................. 1

D. Blade Wrench .......................................................... 2

E. Handle Assembly .................................................... 1

R Rip Fence ................................................................ 1

G. Push Stick ............................................................... 1

H. Indicator ................................................................... 1

Fig. 5

I. Screw ....................................................................... 2

J. Stand Legs ............................................................... 2

K. Sliding Table Assembly ............................................ 1

L. End Cap ................................................................... 1

M. Hex Key .................................................................... 1

N. Switch Key ............................................................... 1

O. Leg Brace ................................................................. 2

R Screw ....................................................................... 8

Q. Lock Nut ................................................................... 8

UNPACKING This product requires assembly.

• Carefully lift saw from the carton and place it on a level work surface.

NOTE: This tool is heavy. To avoid back injury, keep your knees bent and lift with your legs, not your back, and get help when needed.

WARNING: Do not use this product if any parts on the Loose Parts List are already assembled to your

product when you unpack it. Parts on this list are not assembled to the product by the manufacturer and require customer installation. Use of a product that may have been improperly assembled could result in

serious personal injury.

• Inspect the tool carefully to make sure no breakage or damage occurred during shipping.

• Do not discard the packing material until you have carefully inspected the tool, identified all loose parts,

and satisfactorily operated the tool.

NOTE: Remove the foam block from between the

saw's housing and the motor by first beveling the blade (see page 25).

• The saw is factory set for accurate cutting. After assembling it, check for accuracy. If shipping has

influenced the settings, refer to specific procedures

explained in this manual.

• If any parts are damaged or missing, please call

1-800-932-3188 for assistance.

WARNING: If any parts are damaged or missing, do

not operate this tool until the parts are replaced. Use of this product with damaged or missing parts could

result in serious personal injury.

WARNING: Do not attempt to modify this tool

or create accessories not recommended for use with this tool. Any such alteration or modification is

misuse and could result in a hazardous condition leading to possible serious personal injury.

WARNING: Do not connect to power supply until

assembly is complete. Failure to comply could result in accidental starting and possible serious personal

injury.

WARNING: Do not lift the saw without help. Hold

it close to your body. Keep your knees bent and lift with your legs, not your back. Ignoring these precau-

tions can result in back injury.

WARNING: Never stand directly in line with the

blade or allow hands to come closer than 3 in. to the blade. Do not reach over or across the blade. Failure

to heed this warning can result in serious personal

injury.

WARNING: To avoid serious personal injury,

always make sure the table saw is securely mounted

to a workbench or an approved leg stand. NEVER

operate the saw on the floor.

MOUNTING HOLES

The table saw must be mounted to a firm supporting surface such as a workbench or leg stand. If bolted to a workbench, remove the four locking knobs. Four bolt holes have been provided in the saw's base for this pur- pose. Each of the four mounting holes should be bolted securely using 3/8 in. machine bolts, lock washers, and hex nuts (not included). Bolts should be of sufficient length to accommodate the saw base, lock washers, hex nuts, and the thickness of the workbench. Tighten all four bolts securely.

Carefully check the workbench after mounting to make sure that no movement can occur during use. If any tip- ping, sliding, or walking is noted, secure the workbench to the floor before operating.

TO ASSEMBLE THE QUICKSTAND R_

See Figures 6- 7.

NOTE: Do not use this leg stand with other equipment or for other purposes. The arrows on the leg brace identify the top end (short end) of the leg brace.

• Match arrows on the top end of the leg brace with the arrows on the top of the stand leg as shown in figure 6.

• Place the upper holes on the left side leg brace over

the upper holes on the leg assembly. Secure in place with a screw and lock nut.

• Place the upper holes on the right side leg brace under

the upper holes on the second leg assembly. Secure in

place with a screw and lock nut.

• Repeat above steps for the second leg assembly and leg brace.

NOTE: Only mount the saw when the stand is completely opened.

+ 32 hidden pages