Craftsman 137212520 Owner’s Manual
Operator's Manual
CRFIFrSMAN°
10 in. COMPOUND MITER SAW
AND STAND WITH LASER TRAC ®
Model No. 137.212520
CAUTION:
Before using this Miter Saw,
read this manual and follow
all its Safety Rules and
Operating Instructions
Customer Help Line
For Technical Support
1-800-843-1682
Sears, Roebuck and Co., Hoffman Estates, IL 60179 USA
Visit our Craftsman website: www.sears.com/craftsman
Part No. 137212520001
• Safety Instructions
• Installation
• Operation
• Maintenance
• Parts List
Sears Parts &
Repair Center
1-800-488-1222
SECTION PAGE
Warranty ............................................................. 2
Product Specifications ........................................ 2
Power Tool Safety .............................................. 3
Compound Miter Saw Safety .............................. 4
Electrical Requirements and Safety .................... 4
Accessories and Attachments ............................ 8
Tools Needed for Assembly ................................ 8
SECTION PAGE
Carton Contents .................................................. 7
Know Your Compound Miter Saw ....................... 8
Glossary of Terms ............................................... 9
Assembly and Adjustments ................................. 10
Operation ............................................................ 18
Maintenance ....................................................... 25
Troubleshooting Guide ........................................ 26
Parts List ............................................................. 27
ONE-YEAR FULL WARRANTY ON CRAFTSMAN TOOL
If this Craftsman tool fails due to a defect in material or workmanship within one year from the date of purchase,
CALL 1-800-4-MY-HOME® TO ARRANGE FOR FREE REPAIR (or replacement if repair proves impossible).
If this tool is used for commercial or rental purposes, this warranty will apply for only ninety days from the date of
purchase. This warranty applies only while this tool is in the United States.
This warranty gives you specific legal rights, and you may also have other rights, which vary, from state to state.
Sears, Roebuck and Co., Hoffman Estates, IL 60179
WARNING I
Some dust created by power sanding, sawing, grinding, drilling and other construction activities contains
chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these
chemicals are:
• Lead from lead-based paints
• Crystalline silica from bricks, cement and other masonry products
• Arsenic and chromium from chemically treated lumber
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your
exposure to these chemicals, work in a well ventilated area and work with approved safety equipment such as
dust masks that are specially designed to filter out microscopic particles.
MOTOR
Power Source ...................... 120V AC, 60Hz, 15 Amp
Arbor Shaft Size .................. 5/8 in.
Speed .................................. 4800 RPM (No lead)
Brake ................................... Electric
Double Insulated .................. Yes
MITER SAW
Rotating Table:
Miter Detent Stops ................ 0°, 15°, 22.5°, 31.6°, 45° R & L
Bevel Positive Stops ............. 0°, 45 ° L
Cutting Capacity:
Crosscut ................................... 2-5/8 in. x 5-1/2 in.
Miter 45 ° R & L ......................... 2-5/8 in. x 3-1/2 in.
Bevel 45° L ............................... 1-1/2 in. x 5-1/2 in. L
45 ° Miter and 45 ° Bevel ............ 1-1/2 in. x 3-1/2 in.
Extension Bars ....................... Yes
Stand ....................................... Yes
I_t_ WARNING
To avoid electrical hazards, fire hazards or damage to the tool, use proper circuit protection.
This tool is wired at the factory for 110-120 Volt operation. It must be connected to a 110-120 Volt / 15 Ampere
time delay fuse or circuit breaker. To avoid shock or fire, replace power cord immediately if it is worn, cut or
damaged in any way.
Before using your tool, it is critical that you read and understand these safety rules. Failure to follow these
rules could result in serious injury to you or damage to the tool.
2
GENERAL SAFETY INSTRUCTIONS
BEFORE USING THIS POWER TOOL
Safety is a combination of common sense, staying alert
and knowing how to use your power tool.
WARNING J
To avoid mistakes that could cause serious injury,
do not plug the tool in until you have read and
understood the following.
1. READ and become familiar with the entire Operator's
Manual. LEARN the tool's application, limitations and
possible hazards.
2. KEEP GUARDS IN PLACE and in working order.
3. REMOVE ADJUSTING KEYS AND WRENCHES.
Form the habit of checking to see that keys and
adjusting wrenches are removed from the tool before
turning ON.
4. KEEP WORK AREA CLEAN. Cluttered areas and
benches invite accidents.
12.ALWAYS WEAR EYE PROTECTION. Any power
tool can throw foreign objects into the eyes and
_,_ _ could cause permanent eye damage.
ALWAYS wear Safety Goggles (not
glasses) that comply with ANSI Safety
standard Z87.1 Everyday eyeglasses
have only impact-resistant lenses.
They ARE NOT safety glasses. Safety Goggles are
available at Sears. NOTE: Glasses or goggles not in
compliance with ANSI Z87.1 could seriously injure
you when they break.
13.WEAR A FACE MASK OR DUST MASK. Sawing
operation produces dust.
14.SECURE WORK. Use clamps or a vise to hold work
when practical. It is safer than using your hand and it
frees both hands to operate the tool.
15.DISCONNECT TOOLS FROM POWER SOURCE
before servicing, and when changing accessories
such as blades, bits and cutters.
1&REDUCE THE RISK OF UNINTENTIONAL
STARTING. Make sure switch is in the OFF position
before plugging the tool in.
5. DO NOT USE IN DANGEROUS ENVIRONMENTS.
Do not use power tools in damp locations, or expose
them to rain or snow. Keep work area well lit.
6. KEEP CHILDREN AWAY. All visitors and bystanders
should be kept a safe distance from work area.
7. MAKE WORKSHOP CHILD PROOF with padlocks,
master switches or by removing starter keys.
8. DO NOT FORCE THE TOOL. It will do the job better
and safer at the rate for which it was designed.
9. USE THE RIGHT TOOL. Do not force the tool or an
attachment to do a job for which it was not designed.
10.USE PROPER EXTENSION CORDS. Make sure
your extension cord is in good condition. When
using an extension cord, be sure to use one heavy
enough to carry the current your product will draw.
An undersized cord will result in a drop in line voltage
and in loss of power which will cause the tool to
overheat. The table on page 5 shows the correct
size to use depending on cord length and nameplate
ampere rating. If in doubt, use the next heavier
gauge. The smaller the gauge number, the heavier
the cord.
11.WEAR PROPER APPAREL. Do not wear loose
clothing, gloves, neckties, rings, bracelets or other
jewelry which may get caught in moving parts.
Nonslip footwear is recommended. Wear protective
hair covering to contain long hair.
17.USE RECOMMENDED ACCESSORIES. Consult this
Operator's Manual for recommended accessories.
The use of improper accessories may cause risk of
injury to yourself or others.
1&NEVER STAND ON THE TOOL. Serious injury
could occur if the tool is tipped or if the cutting tool is
unintentionally contacted.
19.CHECK FOR DAMAGED PARTS. Before further
use of the tool, a guard or other part that is damaged
should be carefully checked to determine that it will
operate properly and perform its intended function
- check for alignment of moving parts, binding of
moving parts, breakage of parts, mounting and any
other conditions that may affect its operation. A guard
or other part that is damaged should be properly
repaired or replaced.
20.NEVER LEAVE THE TOOL RUNNING
UNATTENDED. TURN THE POWER "OFF". Do not
walk away from a running tool until the blade comes
to a complete stop and the tool is unplugged from the
powe r souroe.
21 .DO NOT OVERREACH. Keep proper footing and
balance at all times.
22.MAINTAIN TOOLS WITH CARE. Keep tools sharp
and clean for best and safest performance. Follow
instructions for lubricating and changing accessories.
23.WARNING: Dust generated from certain materials
can be hazardous to your health. Always operate
saw in well-ventilated area and provide for proper
dust removal.
SPECIFIC SAFETY INSTRUCTIONS FOR
THIS COMPOUND MITER SAW
1&IMPORTANT: After completing the cut, release the
trigger and wait for the blade to stop before returning
the saw to the raised position.
1. DO NOT USE THIN KERF BLADES they can deflect
and contact guard and can cause possible injury to
the operator.
2. DO NOT operate the miter saw until it is completely
assembled and installed according to these
instructions.
3. IF YOU ARE NOT thoroughly familiar with the
operation of miter saws, seek guidance from your
supervisor, instructor or other qualified person.
4. ALWAYS hold the work firmly against the fence and
table. DO NOT perform any operation free hand (use
clamp wherever possible).
5. KEEP HANDS out of the path of the saw blade. If the
workpiece you are cutting would cause your hands
to be within 6-3/4 in. of the saw blade, the workpiece
should be clamped in place before making the cut.
6. BE SURE the blade is sharp, runs freely and is free
of vibration.
7. ALLOW the motor to come up to full speed before
starting a cut.
8. KEEP THE MOTOR AIR SLOTS CLEAN and free of
chips or dust.
9. ALWAYS MAKE SURE all handles are tight before
cutting, even if the table is positioned in one of the
positive stops.
10.BE SURE both the blade and the collar are clean
and the arbor bolt is tightened securely.
11.USE only blade collars specified for your saw.
12.NEVER use blades larger in diameter than 10 inches.
13.NEVER apply lubricants to the blade when it is
running.
14.ALWAYS check the blade for cracks or damage
before operation. Replace a cracked or damaged
blade immediately.
15.NEVER use blades recommended for operation at
less than 4800 RPM.
1&ALWAYS keep the blade guards in place and use at
all times.
17.NEVER reach around the saw blade.
20.MAKE SURE the blade has come to a complete stop
before removing or securing the workpiece, changing
the workpiece angle or changing the angle of the
blade.
21 .NEVER cut metals or masonry products with this
tool. This miter saw is designed for use on wood and
wood-like products.
22.NEVER cut small pieces. If the workpiece being cut
would cause your hand or fingers to be within 6-3/4
in. of the saw blade the workpiece is too small.
23.PROVIDE adequate support to the sides of the saw
table for long work pieces.
24.NEVER use the miter saw in an area with flammable
liquids or gases.
25.NEVER use solvents to clean plastic parts. Solvents
could possibly dissolve or otherwise damage the
material.
26.SHUT OFF the power before servicing or adjusting
the tool.
27.DISCONNECT the saw from the power source and
clean the machine when finished using.
28.MAKE SURE the work area is clean before leaving
the machine.
29.SHOULD any part of your miter saw be missing,
damaged, or fail in any way, or any electrical
component fail to perform properly, lock the switch
and remove the plug from the power supply outlet.
Replace missing, damaged, or failed parts before
resuming operation.
I=1ai |-'t ::( LuJI-'t::l ::l i
POWER SUPPLY AND MOTOR SPECIFICATIONS
The AC motor used in this saw is a universal,
nonreversible type. See "MOTOR" in the "PRODUCT
SPECIFICATIONS" section on page 2.
[,A WARNING J
To avoid electrical hazards, fire hazards, or damage
to the tool, use proper circuit protection. Your saw
is wired at the factory for 120 V operation. Connect
to a 120 V, 15 A circuit and use a 15 A time delay
fuse or circuit breaker. To avoid shock or fire, if
power cord is worn or cut, or damaged in any way,
have it replaced immediately.
18.MAKE SURE the blade is not contacting the
workpiece before the switch is turned ON.
ELECTRICALREQUIREMENTS- cont'd
DOUBLEINSULATED[]
The power tool is double insulated to provide a double
thickness of insulation between you and tool's electrical
system. All exposed metal parts are isolated from
the internal metal motor components with protecting
insulation.
Replacement parts - When servicing, use only
identical replacement parts.
Polarized plugs - This saw has a plug that looks like
the one shown below:
To reduce the risk of electrical shock, this saw has a
polarized plug (one blade is wider than the other). This
plug will fit in a polarized outlet only one way. If the plug
does not fit fully in the outlet, reverse the plug. If it still
does not fit, contact a qualified electrician to install the
proper outlet. Do not change the plug in any way.
4. FUSES may "blow" or circuit breakers may trip
frequently if:
a. MOTOR is overloaded - overloading can occur
if you feed too rapidly or make too many start/
stops in a short time.
b. LINE VOLTAGE is more than 10% above or
below the nameplate voltage rating. For heavy
loads, the voltage at motor terminals must equal
the voltage specified on the nameplate.
c. IMPROPER or dull saw blades are used.
5. Most motor troubles may be traced to loose or
incorrect connections, overload, low voltage or
inadequate power supply wiring. Always check the
connections, the load and supply circuit if the motor
doesn't run well. Check minimum gauge for the
length of cord you are using on the chart below.
GUIDELINES FOR EXTENSION CORDS
Use a proper extension cord. Make sure your extension
cord is in good condition. When using an extension
cord, be sure to use one heavy enough to carry the
current your product will draw. An undersized cord will
cause a drop in line voltage, resulting in loss of power
and overheating. The table below shows the correct size
to use depending on cord length and nameplate ampere
rating. If in doubt, use the next heavier gauge. The
smaller the gauge number, the heavier the cord.
[A WARNING I
Double insulation does not take the place of normal
safety precautions when operating this tool.
To avoid electrocution:
1. Use only identical replacement parts when servicing
a tool with double insulation. Servicing should be
performed by a qualified technician.
2. Do not use power tools in wet or damp locations or
expose them to rain or snow.
MOTOR SAFETY PROTECTION
IMPORTANT
To avoid motor damage, the motor should be blown out
or vacuumed frequently to keep sawdust from interfering
with the motor ventilation.
1. Connect this saw to a 120 V circuit. This circuit
must not be less than a #12 wire with a 20 A time
lag fuse or a #14 wire with a 15 A time lag fuse.
NOTE: When using an extension cord on a circuit
with a #14 wire, the extension cord must not exceed
25 feet in length.
2. If the motor will not start, release the trigger switch
immediately. UNPLUG THE SAW. Check the saw
blade to make sure it turns freely. Ifthe blade is free,
try to start the saw again. If the motor still does not
start, refer to the TROUBLESHOOTING GUIDE.
3. If the tool suddenly stalls while cutting wood, release
the trigger switch, unplug the tool and free the blade
from the wood. The saw may now be started and
the cut finished.
Be sure your extension cord is properly wired and
in good condition. Always replace a damaged extension
cord or have it repaired by a qualified person before
using it. Protect your extension cords from sharp
objects, excessive heat and damp or wet areas.
Use a separate electrical circuit for your tools, This
circuit must not be less than a #12 wire with a 20 A
time lag fuse era #14 wire with a 15 Atime lag fuse.
NOTE: When using an extension cord on a circuit with
a #14 wire, the extension cord must not exceed 25 feet
in length. Before connecting the tool to the power line,
make sure the switch is in the OFF position and the
electric current is rated the same as the current stamped
on the motor nameplate, running at a lower voltage will
damage the motor.
(When using 120 volts only)
Ampere Rating
More Than Not More Than
0 6
6 10
10 12
Total length of Cord
25ft. 50ft. 100ft. 150ft.
8 16 16 14
8 16 14 12
6 16 14 12
CAUTION: In all cases make certain the receptacle in
question is properly grounded, If you are not sure,
have a certified electrician check the receptacle.
RECOMMENDED ACCESSORIES
WARNING I
• Use only accessories recommended for this
miter saw. Follow instructions that accompany
accessories. Use of improper accessories may
cause hazards.
• The use of any cutting tool except 10 in. saw
blades which meet the requirements under
recommended accessories is prohibited. Do
not use accessories such as shaper cutters or
dado sets. Ferrous metal cutting and the use of
abrasive wheels is prohibited.
• Do not attempt to modify this tool or create
accessories not recommended for use with
this tool. Any such alteration or modification is
misuse and could result in a hazardous condition
leading to possible serious injury.
ACCESSORIES
Visit your Sears Hardware Department or see the
Sears Power and Hand Tool Catalog to purchase
recommended accessories for this power tool.
IAWARNING
To avoid the risk of personal injury, do not modify this
power tool or use accessories not recommended by
Sears.
Supplied
Blade Wrench
Not supplied
Adjustable Wrench
Hex Key 2.5 mm
Combination Square
Philips Screwdriver
COMBINATION SQUARE MUST BE TRUE
Should not gap or overlap when square is flipped over
(see dotted figure).
Straight edge or
a 3/4 in. board,
Draw light line on board this edge must be
along this edge. perfectly straight.
WARNING I
Read warnings and conditions on your CARBIDE TIPPED
SAW BLADE. Do not operate the saw without the proper
saw blade guard in place. Carbide isa very hard but
brittle material. Care should be taken while mounting,
using, and storing carbide tipped blades to prevent
accidental damage. Slight shocks, such as striking the
tip while handling, can seriously damage the blade.
Foreign objects in the workpiece, such as wire or nails,
can also cause tips to crack or break off. Before using,
always visually examine the blade and tips for bent
blade, cracks, breakage, missing or loose tips, or other
damage. Do not use if damage is suspected. Failure
to heed safety instructions and warnings can result in
serious bodily injury.
Gap from untrue square
when flipped over.
UNPACKING YOUR MITER SAW
IA WARNING I
To avoid injury from unexpected starting or
electrical shock, do not plug the power cord into a
source of power during unpacking and assembly.
This cord must remain unplugged whenever you are
working on the saw.
1. Remove the miter saw from the carton.
IMPORTANT: Do not lift miter saw by the Trigger
Switch handle. It may cause misalignment. Lift
machine by the built-in carry handle.
2. Place the saw on a secure stationary work surface.
3. Separate all parts from the packing material. Check
each one with the illustration to make certain all items
are accounted for, before discarding any packing
material.
WARNINGI
If any part is missing or damaged, do not attempt
to assemble the miter saw, or plug in the power
cord until the missing or damaged part is correctly
replaced. To avoid electric shock, use only identical
replacement parts when servicing double insulated
tools. Call 1-800-4-MY-HOME ®for replacement parts.
Hold-Down Clamp Lock Knobs
__ Blade Wrench
Hold-Down Clamp
Miter Saw
Dust Bag Elbow
Dust Bag
Short Bottom Support Short Upper Support Hardware Bag
Miter Handle
Long Bottom Support
Foot Pad
Extension Table
Stand Legs
Screws
Long Upper Support
Batteries
CuttingHead
Switch Handle
LaserGuide
LowerBladeGuard
BevelScale
SlidingFence
Bevel Lock Handle
Positive Stop Locking Lever
Stand
ON/OFF Trigger Switch
........ Carrying Handle
Motor
Stop Latch
J Right Extension Table
Stop Plate
Quick-Cam Miter Table Lock
Laser Guide Locking Lever
Upper Blade Guard _.
Dust Bag
Left Extension Table
Stop Plate
Safety Lock-Off Button
Cover Plate
\
Laser Guide Tab
Table Table Insert
iJ --_Extension Table Lock Knob
J
Mounting Hole
Base
Miter Lock Handle
Miter Scale
Positive Miter Detents
8
COMPOUND MITER SAW TERMS
ARBOR LOCK - Allows the user to keep the blade
from rotating while tightening or loosening the arbor bolt
during blade replacement or removal.
WRENCH STORAGE - Convenient storage to prevent
misplacing the blade wrench.
WOODWORKING TERMS
BASE - Supports the table, holds accessories and
allows for workbench or leg set mounting.
BEVEL LOCKING HANDLE - Locks the miter saw at a
desired bevel angle.
BEVEL SCALE - To measure the bevel angle of the
saw blade 0° to 45° left.
COVER PLATE SCREW - Loosen this screw and rotate
the plate for access to the blade arbor bolt.
FENCE - Helps to keep the workpiece from moving
when sawing. Scaled to assist with accurate cutting.
LOWER BLADE GUARD - Helps protect your hands
from the blade in the raised position, it retracts as the
blade is lowered.
MITER HANDLE - Used to rotate the table, and to
rotate the saw to a right or left cutting position.
MITER SCALE - Measures the miter angle 0° to 45° left
and right.
MOUNTING HOLES - To mount the miter saw to a
stable sutrace.
ON/OFF TRIGGER SWITCH - To start the tool, push
the safety lock-off button and squeeze the trigger.
Release the trigger to turn off the miter saw.
POSITIVE STOP LOCKING LEVER - Locks the miter
saw at a preset positive stop for the desired miter angle.
STOP LATCH - Locks the miter saw in the lowered
position for compact storage and transportation.
SWITCH HANDLE - The switch handle contains
the trigger switch and safety lock-off button. The blade
is lowered into the workpiece by pushing down on the
handle. The saw will return to its upright position when
the handle is released.
ARBOR - The shaft on which a blade is mounted.
BEVEL CUT - An angle cut made through the face of
the workpiece.
COMPOUND OUT - A simultaneous bevel and miter
cut.
CROSS CUT - A cut made across the width of the
workpiece.
FREEHAND - Performing a cut without using a fence
(guide), hold down or other proper device to prevent the
workpiece from twisting during the cutting operation.
GUM - A sticky sap from wood products.
HEEL - Misalignment of the blade.
KERF - The amount of material removed by blade cut.
MITER CUT - An angle cut made across the width of
the workpiece.
RESIN - A sticky sap that has hardened.
REVOLUTIONS PER MINUTE (RPM) - The number of
turns completed by a spinning object in one minute.
SAW BLADE PATH - The area of the workpiece or
table top directly in line with the travel of the blade or the
part of the workpiece which will be cut.
SET - The distance between two saw blade tips, bent
outward in opposite directions to each other. The further
apart the tips are, the greater the set.
WORKPIECE - The item being cut. The surfaces of a
workpiece are commonly referred to as faces, ends and
edges.
WARNING LABELS - Read and understand for your
own safety. Make sure all labels are present on machine
and legible.
ASSEMBLY INSTRUCTIONS
1,4 WARNING I
To avoid injury, do not connect this miter saw to the
power source until it is completely assembled and
adjusted and you have read and understood this
Operator's Manual.
ASSEMBLE STAND (FIG. A)
1. Unpack all parts and group by type and size. Refer to
the parts list on page 30 for correct quantities.
2. Attach one long upper support (4) to top of leg (1)
using one carriage bolt (2) and nut (5).
NOTE: Do not tighten bolts until stand is properly
aligned (see step #8).
3. Attach other end of long upper support to the top of
another leg using one carriage bolt and one nut.
4. Attach one long bottom support (3) to the center of
each leg using carriage bolt and nut. This completes
the front frame section.
5. Assemble the rear frame section in exactly the same
manner.
6. Join the front and rear frame assemblies using
two short upper supports (6) and two short bottom
supports (8), carriage bolts and nuts.
7. Place all four foot pads (7) onto each leg.
8. Place the stand on a level surface and adjust it so all
legs are contacting the floor and are at similar angles
to the floor. Tighten all bolts.
NOTE: Stand should not rock after all bolts are
tightened.
ASSEMBLE MITER SAW TO STAND
1. Carefully place the miter saw on top of stand.
2. Line up the four mounting holes in the saw base to
the stand.
3. Fasten the saw to the stand using the four mounting
screws (9), four washers (10) and four nuts (11).
NOTE: Place a washer on each bolt before inserting
it into the saw base and through the support, then
thread the nut onto the bolt. (see Fig. A)
4. Tighten all four nuts.
NOTE: DO NOT OVER TIGHTEN THE LOCK NUTS
HOLDING SAW TO THE STAND. THIS COULD
DAMAGE THE SAW BASE.
Fig. A
Saw Base (saw not
shown for clarity of vi._w). _
2
5
_'-7
Loading...