LASER DISTANCE METER CONDTROL SMART 20
User manual
Display
5 
6
1.Main display line
2.Secondary display line
3.Battery charge level
4.Measuring unit
5.Laser beam indication
6.Reference point
LASER DISTANCE METER CONDTROL SMART 20
User manual
MESSAGE CODES
While operation, the following codes/symbols may appear on the display:
Message |
Cause |
Solution |
|
204 |
Calculation error |
Refer to user manual, repeat |
|
the procedure. |
|||
|
|
||
208 |
Excessive current |
Please contact the distributor |
|
or authorized service center. |
|||
|
|
||
220 |
Batteries are low |
Replace the batteries. |
|
|
Operating |
Cool down the device to |
|
252 |
temperature is |
temperature within 0…+400С. |
|
|
too high |
|
|
|
Operating |
Warm up the device to |
|
253 |
temperature is |
temperature within 0…+400С |
|
|
too low |
|
|
255 |
Received signal is |
Make measurements against |
|
|
too weak |
surface with better reflective |
|
|
|
properties. Use a reflecting |
|
|
|
plate. |
|
|
|
|
LASER DISTANCE METER CONDTROL SMART 20
User manual
Congratulations on your purchase of laser distance meter CONDTROL SMART 20.
Safety instructions can be found in the end of this user manual and should be carefully read before you use the device for the first time.
FUNCTIONS/APPLICATIONS
Laser distance meter SMART 20 is intended to measure distance at indoor building areas.
PACKAGE
1. Laser distance meter – 1pc.
2. Batteries (type ААА) - 2 pcs.
3. User manual – 1 pc.
SPECIFICATIONS
Working range |
0,2…20m* |
|
|
Smallest unit displayed |
1mm |
|
|
Measuring accuracy |
±3mm** |
|
|
|
Class II, |
Laser type |
630-670nm, |
|
< 1mW |
Continuous measurement (tracking) |
+ |
|
|
Display backlight |
+ |
LASER DISTANCE METER CONDTROL SMART 20
User manual
OPERATION Insert/replace batteries
Remove the battery cover. Insert the batteries, observing correct polarity. Put the battery cover back. Remove the batteries when the device is not used for a long time to avoid corrosion and battery depletion. Both batteries should be replaced at the same time. Both batteries must be of the same brand with the same charge level. Replace batteries when you see symbol 
on the display.
Switch on/off |
|
Switch on: press and hold for 1 sec. button |
. |
The device will turn on and enter single distance measuring mode. Laser beam will turn on simultaneously. Laser beam automatically turns off in 30 seconds after the last operation.
Switch off: press and hold for 1 sec. button |
. |
|
In order to save battery power the device will |
switch off |
|
automatically within 3 minutes after the last operation.
LASER DISTANCE METER |
|
CONDTROL SMART 20 |
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
User manual |
|
|
|
|
|
|
|
|
|
|
|
Make |
measurements against |
|
256 |
|
Received signal is |
surface with lower reflective |
|||
|
properties. |
Use a reflecting |
||||
|
|
too strong |
plate. |
|
|
|
|
|
Outside of |
Carry |
out |
measurements |
|
261 |
|
within |
the |
range acceptable |
||
|
|
measuring range |
for this device. |
|||
500 |
|
Hardware error |
Switch on/off the device several |
|||
|
times. If this error still appears, |
|||||
|
|
|
|
please contact the distributor |
||
|
|
|
|
or authorized service center. |
||
LASER DISTANCE METER CONDTROL SMART 20
User manual
CARE AND MAINTENANCE
Attention! The instrument is a high precision device and requires careful handling. The following recommendations will extend the life of the device:
-Do not point the device at the sun
-Protect the device from bumps, falls and excessive vibration; do not let liquids, construction dust and foreign objects get inside the device.
-Do not expose the device to extreme temperatures.
-If liquids get inside the device first remove batteries, then contact a service center.
-Do not store or use the device under high humidity conditions for a long time.
-Clean the device with soft wet cloth.
-Keep device optics clean and protect it from mechanical damage.
-Сarry out control measurements occasionally, especially if the device is subject to excessive mechanical or other impact, before and after making important measurements.
LASER DISTANCE METER CONDTROL SMART 20
User manual
UTILIZATION
Expired tools, accessories and package should be passed for waste recycle. Please send the product to the following address for proper recycle:
CONDTROL GmbH
Wasserburger Strasse 9
84427 Sankt Wolfgang
Germany
Do not throw the product in municipal waste!
AccordingtoEuropeandirective2002/96/ЕCexpiredmeasuring tools and their components must be collected separately and submitted to environmentally friendly recycle of wastes.
LASER DISTANCE METER |
|
CONDTROL SMART 20 |
||
|
|
|
|
|
|
|
|
|
User manual |
|
|
|
||
Automatic shutdown of laser |
|
30sec. |
||
|
|
|||
Automatic shutdown of laser distance meter |
180sec. |
|||
|
|
|
||
Storage temperature |
|
-10…+60°С |
||
|
|
|
||
Working temperature |
|
0…+40°С |
||
|
|
|
|
|
Battery |
|
2 х 1.5V AAA LR3 |
||
|
(alkaline) |
|||
|
|
|
|
|
|
|
|
|
|
Battery life |
|
up to 5000 |
||
|
measurements |
|||
|
|
|
|
|
|
|
|
||
Dimensions |
|
100х40х25mm |
||
|
|
|
||
Weight |
|
80g |
||
|
|
|
|
|
*Use a reflecting plate to increase the measurement range during daylight or if the target has poor reflective properties.
**In favorable conditions (good target surface properties, room temperature) up to 10 m. In unfavorable conditions, such as intense sunshine, poorly reflecting target surface or considerable temperature variations, accuracy can decrease at distance over 10m.
LASER DISTANCE METER CONDTROL SMART 20
User manual
Display backlight
When the device is on, backlight turns on automatically when you press button 
. The backlight will turn off automatically in 10 seconds after last operation.
Reference point
Reference point is the bottom end of the device.
Measuring unit.
Press simultaneously buttons 
and 
to select the reference point – m (meter) or ft (foot).
MEASUREMENTS
1) Single distance measurement
Short press button 
to switch on the device. Laser beam will be on. Point the laser beam at the target and short press button 
for single distance measurement. The result of measurement will appear in the main line on the display.
To perform next single distance measurement press button 
to turn on the laser beam and then press 
again.
LASER DISTANCE METER CONDTROL SMART 20
User manual
PRODUCT DESCRIPTION
Display
Switch on / turn on laser beam
/ make measurement /continuous measurement
Switch off/clear
LASER DISTANCE METER CONDTROL SMART 20
User manual
2) Continuous measurement (tracking)
When in single distance measurement mode press and hold for 1 sec. button 
. The device will take measurements one after the other, showing the last measured value. To stop continuous measurement press button 
or 
.
To exit the mode short press 
.
LASER DISTANCE METER CONDTROL SMART 20
User manual
SAFETY REGULATIONS
The user manual should be read carefully before you use the device for the first time. Unintended use of the device can be dangerous for human’s health and cause serious injury. Keep this user manual. If the device is given to somebody for temporary use, be sure to enclose user manual to it.
-Do not misuse the device.
-Donotremovewarningsignsandprotectthemfromabrasion, because they contain information about safe operation of the device.
Laser radiation!
Do not stare into beam Class 2 laser
<1 mW, 630-670 nm IEC 60825-1: 2007-03
-Do not look into the laser beam or its reflection, with unprotected eye or through an optical instrument. Do not point the laser beam at people or animals without the need. You can dazzle them.
-To protect your eyes close them or look aside.
-It is prohibited to disassemble or repair the device yourself.
Entrust device repair to qualified personnel and use original spare parts only.
-Do not use the device in explosive environment, close to flammable materials.
LASER DISTANCE METER CONDTROL SMART 20
User manual
- Avoid heating the batteries to avoid the risk of explosion and electrolyte leakage. In case of liquid contact with skin, wash it immediately with soap and water. In case of contact with eyes, flush with clean water during 10 minutes and consult the doctor.
LASER DISTANCE METER CONDTROL SMART 20
User manual
WARRANTY
All CONDTROL GmbH products go through post-production control and are governed by the following terms of warranty. The buyer’s right to claim about defects and general provisions of the current legislation do not expire.
1)CONDTROL GmbH agrees to eliminate all defects of the device, discovered during the warranty period, that represent defect in material or workmanship in full volume and at its own expense.
2)The warranty period is 24 months and starts from the date of purchase by end consumer (see the original supporting document).
3)The warranty doesn’t cover defects resulting from wear and tear or improper use, malfunction of the device caused by failure to observe the instructions of this user manual, untimely maintenance and service and insufficient care, the use of nonoriginal accessories and spare parts. Modifications in design of the device relieve the seller from responsibility for warranty works. The warranty doesn’t cover cosmetic damage, that doesn’t hinder normal operation of the device.
4)CONDTROL GmbH reserves the right to decide on replacement or repair of the device.
5)Other claims not mentioned above, are not covered by the warranty.
6)After warranty works are carried out by CONDTROL GmbH warranty period is not renewed or extended.
7)CONDTROL GmbH is not liable for loss of profit or
LASER DISTANCE METER CONDTROL SMART 20
User manual
inconvenience associated with a defect of the device, the rental cost of alternative equipment for the period of repair.
This warranty applies to German law except provision of the United Nations Convention on contracts for the international sale of goods (CISG).
In warranty case please return the device to retail seller or send it with defect description to the following address:
CONDTROL GmbH
Wasserburger Strasse 9
84427 Sankt Wolfgang
Germany
Loading...