Compuprint 9050 LAN Installation

Ethernet 10/100Base-T Connection
Installation Guide

Table of Contents

Table of Contents ........................................................................ 2
LAN Interface Port ....................................................................... 4
LED Indicators ......................................................................... 4
Installing the Controller Board ............................................... 5
Handling the Controller Board ............................................ 5
Replacing the Controller Board ............................................ 6
Connecting Printer to the LAN ............................................... 9
Selecting LAN Interface in the Printer Setup ............................. 10
Printing Power-On Configuration Setup Page ............................ 10
Configuring the LAN Interface Through the Printer
Operator Panel ....................................................................... 12
Windows Environment ............................................................. 13
Software Installation & Configuration in Windows 98
Environment ........................................................................... 13
Port Installation .................................................................. 13
TCP/IP Protocol - Printer Installation ............................... 14
TCP/IP Protocol - Port Configuration ................................ 19
NetBEUI Protocol - Printer Installation ............................ 23
NetBEUI Protocol - Port Configuration ............................. 28
Software Installation & Configuration in Windows 2000
Environment ........................................................................... 31
Port Installation .................................................................. 31
TCP/IP Protocol - Port Configuration ................................ 32
TCP/IP Protocol - Printer Installation ............................... 35
NetBEUI Protocol - Port Configuration ............................. 39
NetBEUI Protocol - Printer Installation ............................ 42
UNIX Environment ..................................................................... 46
Port Installation & Configuration ......................................... 46
Linux 7.x & Solaris 7.x Operating Systems .......................... 49
Configuring a Remote Printer for the Red Hot Linux 7.x
Operating System ............................................................... 49
Configuring a Remote Printer for the Solaris 7.x
Operating System ............................................................... 50
............................................ 4
Table of Contents........................................................................ 2
LAN Interface Port...........................
Windows Environment ............................................................. 1
3
UNIX Environment..................................................................... 46
2 78413025-001
AS/400 Environment ................................................................. 51
Configuring AS/400 for ASCII (TCP/IP protocol) ................. 51
Configuring with ADDTCPIFC .......................................... 51
Configuring a Router Definition with ADDTCPRTE ........ 52
Configuring a Local Domain and Host Name .................... 52
Configuring a TCP/IP Host Table Entry ............................ 52
Configuring AS/400 for Printing ............................................ 53
Setting up Printing for ASCII Files ................................... 53
Monitoring Printer & Remote Printer Configuration .............. 56
tion .............. 56
Printer Configuration ............................................................. 57
NIC Setup ............................................................................... 58
System Setting ........................................................................ 59
Setting the Security Password ............................................... 60
FCC Notes .................................................................................. 62
ICES-003/NMB-003 Notes ......................................................... 62
EEC Regulations ....................................................................... 62
Notes ......................................................... 62
................ 62
AS/400 Environment ................................................................. 51
Monitoring Printer & Remote Printer Configura
FCC Notes.................................................................................. 62
ICES-003/NMB-003
EEC Regulations .......................................................
784103025-001 3

LAN Interface Port

A B
The interface ports are located on the rear of the printer:
A. Parallel Interface Port B. LAN Interface Port:
1. Ethernet 10/100Base-T Connector
2. Green 10/100Mbit/sec. Transmission Speed Led
3. Yellow Traffic Led

LED Indicators

The led indicator modes are described in the following table:
LED Status Description
Green Led
Yellow Led
4 78413025-001
Lit Transmission speed at 10Mbit/sec.
Unlit Transmission speed at 100Mbit/sec.
Blinks Transmitting or receiving packets from
the network.
Unlit No transmitting or receiving packets
from the network.

Installing the Controller Board

Follow the reported instruction in case of Controller Board replacement.

Handling the Controller Board

Attention: Do not remove the Controller Board from the protective package until instructed to do so. Static electricity, though harmless to you, can damage sensitive Controller Board components. Use the information in this section to avoid damaging a Controller Board.
- Limit your movement. Your movement can create static electricity that, when released to the Controller Board, can damage the electronic components on the Controller Board. Sliding your foot across carpeting is an example of how you create unwanted static electricity.
- Handle the Controller Board only by the edges and prevent others from making direct contact with it.
- Before removing the Controller Board from the protective package, ground the package to exposed metal at the back of the printer. This will release any static charge that may have developed on the package or on your body. Hold the package against the metal for at least two seconds.
- When you are instructed, remove the Controller
Board and install it directly into the Controller Board slot without setting it down. If you have removed the Controller Board from the protective package and cannot immediately insert it in the printer, place the protective package on a flat surface, and set the Controller Board on top of the
protective package.
784103025-001 5

Replacing the Controller Board

Attention: Ensure that the printer is powered off before installing or removing the Controller Board. If the Controller Board is installed while the printer is powered on, the controller will not synchronize with the printer mechanism board. Unpredictable printer behavior will result. Perform the following steps to replace the Controller Board:
1. Ensure that the printer is powered off. Installing the Controller Board with the printer power on will result in unpredictable printer behavior.
2. Use the screwdriver that came in the Controller Board box to remove the existing Controller Board and pull out the card.
3. Use the information under “Handling the Controller Board” on the preceding page as you remove the Controller Board from its shipping box and from the protective package.
6 78413025-001
4. Align the left and right sides of the Controller Board with the guides in the printer and slide it into the slot.
5. Gently push the Controller Board into the printer until it is seated in the connector inside the printer. The Controller Board is correctly seated in the printer when the Controller Board metal plate is aligned with the back profile of the slot.
784103025-001 7
6. Attach the Controller Board with the two screws using the screwdriver that came in the Controller Board box.
8 78413025-001

Connecting Printer to the LAN

MMaakkee ssuurree tthhee ppoowweerr sswwiittcchh iiss iinn 00 ppoossiittiioonn ((OOFFFF))..
1. Insert the LAN cable into the Ethernet 10/100Base-T connector.
2. Insert the power cable into the printer connector and the other power cable end into a convenient outlet.
3. Press the power switch in I position (ON) to turn the printer on.
Make sure that the LAN Interface Port Green Led is lit.
784103025-001 9

Selecting LAN Interface in the Printer Setup

It is necessary to configure the printer to the LAN connection. The printer configuration is performed using the operator panel.
The functions concerning the LAN interface are selected in the printer Power-On Configuration setup described in the User Manual included in the Printer Documentation & Driver CD­ROM.

Printing Power-On Configuration Setup Page

If you want to see the current LAN interface setting, print the Power-On Configuration setup page as follows:
1. Make sure that the printer is turned off.
2. Press and hold the
powering on the printer until the RELEASE KEY message is displayed. As soon as the released, the following message will be displayed:
PRINT OUT? NO
3. Press the key, the following message will be
displayed:
PRINT OUT? YES
4. The printout starts.
10 78413025-001
PROGRAM key pressed while
PROGRAM key gets
See a Power-On Configuration setup printout sample in the following page:
PPoowweerr--OOnn CCoonnffiigguurraattiioonn SSeettuupp PPaaggee SSaammppllee
- CONFIGURATION SETUP PRINTOUT ­FIRMWARE CODE: ver. 00.02 78412961 MAC ADDRESS: 00066D03852D
EMUL. OPTIONS EMUL. EPSON LQ CHAR. SET CS2 NATION CP437 AUTO LF NO BAR CODE NATIV
INTERFACE I/F TYPE AUTO
PARALL INTERFACE 1284 BIDIR. I/F SELECT-IN HOST DATA BITS 8 INPUT BUFFER 2K
LAN INTERFACE IP ASSIGN FIXED INIT IP ADDRESS 010.000.200.044 INIT NET MASK 255.255.000.000 DEF. GATEWAY ID 010.000.255.240 INIT HOST NAME CMP_03852D INIT WORKGROUP Compuprint SMTP ENABL. YES MAIL SERV.ADDRES 010.000.254.252 EMAIL ADDRESS admin@sferalwwt.com SENDER ADDRESS 9065@sferalwwt.com
FUNCTIONS BUZZER YES SEQUENCE NONE RIBBON BLACK BAR CODE 1200 DPI TEXT DIRECT BI GRAPH DIRECT BI BARCODES DIR. UNI GRAPH H.S. YES P.ON PATH MACRO MENU ENGLISH TEAR ADJUST 0
784103025-001 11

Configuring the LAN Interface Through the Printer Operator Panel

1. Press the PROGRAM key while powering the printer on, and keep the key pressed until the RELEASE KEY message is displayed.
2. Press the key until you find the LAN INTERFACE item, and set the following paramenters:
- INIT IP ADDRESS
- INIT NET MASK
- DEF. GATEWAY ID
Contact your system administrator for the correct values.
12 78413025-001

Windows Environment

In the Local Area Network printing environment, the PCs can share a printer, that is, different users can use the same printer.
Software installation must be carried out on every PC requiring access to the Compuprint printer. For the communication between the PCs and the Compuprint printer is necessary that the same LAN protocol is used for all connected devices: the TCP/IP or the NetBEUI protocol in a Windows environment

Software Installation & Configuration in Windows 98 Environment

Port Installation

Check that the Printer is powered on and the Green Power led of the LAN Interface Port is lit.
Insert the CD-ROM labeled Compuprint Ethernet LAN.
1. Run the “Compuprint PP” program from the Drivers\Microsoft\Print Port directory. The Compuprint Print Port Install Shield Wizard screen appears:
2. Follow the Compuprint Print Port Setup program instructions. This program installs the Compuprint print port.
784103025-001 13

TCP/IP Protocol - Printer Installation

1. Go to “Start-Settings-Printers” on your PC.
2. Invoke the “Add Printer Wizard”. Click Next button. The following screen appears:
3. Select “Local printer” and click Next button. You will see the “Printers” list option.
14 78413025-001
4. If the printer is not listed and the printer comes with the installation disk. Click Have Disk button. The “Install From Disk” screen appears:
5. Insert the CD-ROM labeled Compuprint Ethernet LAN into the drive. Click Browse button. The “Open” screen appears. Go to the \drivers\microsoft\win98 folders and select the total.inf file.
6. Click OK button. The following screen appears:
784103025-001 15
7. Click OK button. Select your Compuprint model printer (9065, 9080, 9300, 10300).
10300
8. Click Next button. Click the “LPT1” port to use with this printer and then click Next button again.
16 78413025-001
9. Type the name for this printer in the “Printer Name” screen. Click Next button.
10300
10. The “Print Test Page” screen appears. If you want to print the test page, select Yes, then click Finish button to end the procedure.
784103025-001 17
If there are not installed Windows 98 files useful to continue this
procedure in your PC, the following screen appears:
Insert the CD-ROM labeled Windows 98 Second Edition into the drive. Click OK button to copy the files. When the files are copied, insert the CD-ROM labeled Compuprint Ethernet LAN and click OK button.
18 78413025-001

TCP/IP Protocol - Port Configuration

Now configure the port to be connected to the printer.
1. Check in “Printers” window if your Compuprint printer is installed (“Compuprint 10300” in the example). Click on “Compuprint 10300” icon, then click on File selection on the menu bar. Select Properties.
10300
2. The Compuprint printer properties screen appears:
10300
10300
784103025-001 19
3. Click Details button. In the screen that appears you can select the port to be connected to the printer. Click Add Port button.
10300
10300
10300
4. The “Add Port” screen appears. Click “Other” selection. Select “Compuprint Print Port “as the port to use. Click OK button.
20 78413025-001
5. Select “Compuprint Port 9100”. Click OK button to confirm.
6. In the “Port 9100 settings” screen you can configure this port.
To specify the IP-address see the values set in the INIT IP
ADDRESS parameter of the LAN INTERFACE item in the Power­On Configuration setup you find in the User Manual included
in the Printer Documentation & Drivers CD-ROM. Then enter a Port Name in the Port Name field. Click OK
button to confirm.
If you want to set the default network IP-address and Port Name
values, click Browse Network button.
784103025-001 21
7. Click Apply button and then OK button to confirm.
10300
10300
10300
Port configuration is now complete.
22 78413025-001

NetBEUI Protocol - Printer Installation

1. Go to “Start-Settings-Printers” on you PC.
2. Invoke the “Add Printer Wizard”. Click Next button. The following screen appears:
3. Select “Local printer” and click Next button. You will see the “Printers” list option.
784103025-001 23
4. If the printer is not listed and the printer comes with the installation disk. Click Have Disk button. The “Install From Disk” screen appears:
5. Insert the CD-ROM labeled Compuprint Ethernet LAN into the drive. Click Browse button. The “Open” screen appears. Go to the \drivers\microsoft\win98 folders and select the total.inf file.
6. Click OK button. The following screen appears:
24 78413025-001
7. Click OK button. Select your Compuprint model printer (9065, 9080, 9300, 10300).
10300
8. Click Next button. Click the “LPT1” port to use with this printer and then click Next button again.
784103025-001 25
9. Type the name for this printer in the Printer Name field. Click Next button.
10300
10. The “Print Test Page” screen appears. If you want to print the test page, click Yes, then click Finish button to end the procedure.
If there are not installed Windows 98 files useful to continue this
procedure in your PC, the following screen appears:
26 78413025-001
Insert the CD-ROM labeled Windows 98 Second Edition into the drive. Click OK button to copy the files. When the files are copied, insert the CD-ROM labeled Compuprint Ethernet LAN and click OK button.
784103025-001 27

NetBEUI Protocol - Port Configuration

Now configure the port to be connected to the printer.
1. Check in “Printers” window if your Compuprint printer is installed (in the example, the “Compuprint 10300” printer). Click on “Compuprint 10300” icon , then click on File selection on the menu bar. Select Properties.
10300
2. The “Compuprint 10300 Properties” screen appears.
10300
10300
28 78413025-001
3. Click Details button. In the screen that appears you can select the port to be connected to the printer. Click Add Port button.
10300
10300
10300
4. The “Add Port” screen appears. Click “Other” selection. Select “Local Port“ as the port to use. Click OK button.
784103025-001 29
5. The “Port name” screen appears. Enter a port name in the Port Name field (the port name must be present in the local network as hostname, the print queue as prt1). Click OK button to confirm.
\\Hostname\prin t queue_name
6. Click Apply button and then OK button to confirm.
10300
10300
10300
Port configuration is now complete.
30 78413025-001

Software Installation & Configuration in Windows 2000 Environment

Port Installation

Check that the Printer is powered on and the Green Power led of the LAN Interface Port is lit.
Insert the CD-ROM labeled Compuprint Ethernet LAN.
1. Run the “Compuprint PP” program from the
drivers\microsoft\Print Port directory. The Compuprint Print Port Install Shield Wizard screen appears:
2. Follow the Compuprint Print Port Setup program
instructions. This program installs the Compuprint print port.
784103025-001 31

TCP/IP Protocol - Port Configuration

1. Go to “Start-Settings-Printers” on you PC.
2. Invoke the “Add Printer Wizard”. The following screen is prompted. Click Next button.
3. The “Local or Network Printer” screen appears, select “Local printer”.
32 78413025-001
4. Click Next button and the following screen appears:
Now the wizard detects and installs the new Plug and Play printers if you want to install the printer manually, click Next button.
5. In the “Select the Printer Port” screen, click on Create a new port field to select “Compuprint Print Port” as the port to use.
784103025-001 33
6. Click Next button. The “Add New Port” screen appears. Select “Compuprint Port 9100”. Click OK button.
7. The “Port 9100 Settings” screen appears:
To specify the IP-address, see the values set in the INIT IP
ADDRESS parameter of the LAN INTERFACE item in the Power­On Configuration setup you find in the User Manual included
in the Documentation & Drivers CD-ROM.
Then enter a Port Name in the Port Name field. Click OK button to confirm.
If you want to set the default network IP-address and Port Name
values, click Browse Network button.
Port configuration is now complete.
34 78413025-001

TCP/IP Protocol - Printer Installation

Now to install the Compuprint printer to be connected to the new port, click the OK button of the “Port 9100 Settings” screen.
1. You will see the “Printers” list option. If the printer is not listed and the printer comes with the installation disk. Click Have Disk button. The “Install From Disk” screen appears:
2. Insert the CD-ROM Compuprint Ethernet LAN into the drive. Copy the files from the \drivers\microsoft\Win2000 folders and select the compprint.inf file.
784103025-001 35
3. Click OK button. Select your Compuprint model printer (9065, 9080, 9300, 10300).
10300
4. Assign a name for your printer (e.g. Compuprint 10300).
10300
36 78413025-001
5. To share this printer with the other users, provide a share name.
6. Click Next button. The “Location and Comment” screen appears. Write the Location and the Comment you desire.
784103025-001 37
7. Click Next button. The “Print Test Page” screen appears. If you want to see the final printer setting configuration, click “Yes”.
8. This is the Test Page:
10300
10300
9. Click Finish button to end the printer installation procedure.
38 78413025-001

NetBEUI Protocol - Port Configuration

1. Go to “Start-Settings-Printers” on you PC.
2. Invoke the “Add Printer Wizard”. The following screen is prompted. Click Next button.
3. The “Local or Network Printer” screen appears, select “Local printer”.
784103025-001 39
4. Click Next button and the following screen appears:
Now the wizard detects and installs the new Plug and Play printers if you want to install the printer manually, click Next button.
5. In the “Select the Printer Port” screen, click on Create a new port to select “Local Port” as the port to use.
40 78413025-001
6. The “Port name” screen appears. Enter a port name in the Port Name field (the port name must be present in the local network as hostname, the print queue as prt1). Click OK button to confirm.
\\Hostname\print queue_name
784103025-001 41

NetBEUI Protocol - Printer Installation

Now to install the Compuprint printer to be connected to this new port, click on Next button of the “Port Name” screen.
1. You will see “Add Printer Wizard” screen. If the printer is not listed and the printer comes with the installation disk. Click Have Disk button. The “Install From Disk” screen appears.
2. Insert the CD-ROM Compuprint Ethernet LAN into the drive. Copy the files from the \drivers\microsoft\Win2000 folders and select the compprint.inf file name.
42 78413025-001
3. Click OK button. Select your Compuprint model printer (9065, 9080, 9300, 10300).
10300
4. Assign a name for your printer (e.g. Compuprint 10300).
10300
784103025-001 43
5. To share this printer with the other users, provide a share name.
6. Click Next button. The “Location and Comment” screen appears. Write the Location and the Comment you desire.
44 78413025-001
7. Click Next button. The “Print Test Page” screen appears. If you want to see the final printer setting configuration, click “Yes”.
8. This is the Test Page:
10300
10300
9. Click Finish button to end the printer installation procedure.
784103025-001 45

UNIX Environment

To configure the printer in Unix environment, you have to run the “cmpwizard.sh” script from the drivers\unix directory included in this CD-ROM , except for Linus 7.x and Solaris 7.x operating systems described later in this section.

Port Installation & Configuration

Check that the Printer is powered on and the Green Power led of the LAN Interface Port is lit.
It is necessary to be SUPER USER.
Insert the Compuprint Ethernet LAN CD-ROM.
1. From the shell bush, run the “cmpwizard.sh” script from
the drivers\unix directory included in the CD-ROM labeled Compuprint Ethernet LAN. See the following screen:
2. Select the operating system (n.7).
46 78413025-001
3.
Add the IP address. This address m
ust match the IP address selected in the INIT IP ADDRESS parameter the LAN INTERFACE item in the Power-On Configuration setup you find in the User Ma
nual included in the Printer Documentation & Driver C ROM.
4. Enter the Logical Port Name. The Logical Port Name is
“prt1”.
of
D-
784103025-001 47
5. Enter the Print Server Name. The printer server name
is “ps1”.
6. If this configuration is ok , enter “y” to confirm.
The installation is now complete. If you want to print the test file, enter the lpr -Pps1 test command.
48 78413025-001

Linux 7.x & Solaris 7.x Operating Systems

To configure the printer for the Linux 7.x and Solaris 7.x operating systems, follow the corresponding procedure described below:

Configuring a Remote Printer for the Red Hot Linux 7.x Operating System

1. Open the “/etc/hosts” file as root user in a Terminal windows.
2. Add the IP address and the Printer Name information.
Here is an example of an “/etc/hosts” file:
Ip-address Printer-name
10.0.128.220.1
10.0.128.220.2 prt2
3. Type “printconf-gui&” from a prompt.
4. Click New button. You are asked to enter a queue name for the printer. Type the queue name you want.
5. Then select “Type of queue”. Select Unix Printer (lpd queue) in the “Queue type” box.
6. Insert the printer name used in “/etc/hosts” file (i.e. prt1 or prt2 ) in the “Server” or “Remote Hosts” box.
7. Insert the local spool directory (where the print jobs for the Unix computer are to be placed) in the “Queue” or “Spool Directory” box.
8. Select text only in the “Printer Driver” box. Set up the configuration you want and then click OK button.
9. Click File ->Save Changes in the “printconf-gui” window.
10. Restart lpd to have (let) the printer daemon receive the new printer entry.
If the print job is rejected when it is sent to test the printer, ask the
remote computer’s administrator to check permission in the
“/etc/lpd.perms” file.
prt1
784103025-001 49

Configuring a Remote Printer for the Solaris 7.x Operating System

1. Open the “/etc/hosts” file as root user in a Terminal windows.
2. Add the IP address and the Printer Name information.
Here is an example of an “/etc/hosts” file:
Ip-address printer-name
10.0.128.220.3 prt1
10.0.128.220.4 prt
Type “admi inal w ws. ntool&” in a Term indo
3.
4. Select
5. Select Edit->Add->Access to Print Printer Menu”.
6. Insert the printer name you want in the box.
7. Insert the printer name or prt2) in the “Printer Server” box.
8. Click Apply and then OK button.
Now you are ready to use the printer.
Browse button and then Printers.
used in “/etc/hosts” file (i.e. prt1
2
in the “Admintool
“Printer Name”
50 78413025-001

AS/400 Environment

Configuring AS/400 for ASCII (TCP/IP protocol)

Configuring with ADDTCPIFC

AD ce to AS/400.
DTCPIFC is used to add a TCP/IP interfa
This step configures r con ion to a TCP/IP network.
1. At the AS/400 command line, r the following command:
ADDTCPIFC INTNETADR(127.000.000.000)LIND(ETHLAN) SUBNETMASK (
This screen should look like the following one:
the AS/400 fo nect
ente
255.255.254.000)
Internet address …………………………….. :
Subnet mask …………
Line description ………………………………:
T
o specify the IP-address and the Subnet Mask, see the values set respectively in the parameters of the LAN INTERFACE item in the Power-On Configuration setup you find in the User Manual included in the Printer Documentation & Driver CD-ROM.
784103025-001 51
……………………… :
INIT IP ADDRESS and INIT NET MASK
127.000.000.000.
255.255.254.000
ETHLAN
Configurin
g a Router Definition with
ADDTCPRTE
If necessary, use the ADDTCPRTE command definition. This is required than on a local segment.
if the printer is somewhere other
Configuring a Local Domain an
The AS/400 print commands require a local name and name. If you have already configured LAN attached TCP/IP printers on the AS/400 system, you will have a local domain name and hostname configured on the system.
To configure the local domain, command.
Confi
Although it is y, it is suggested that you take this step. Add the AS/400 name and the LAN IP address to the “Host Table Entries”.
guring a TCP/IP Host Table Entry
optional to create a TCP/IP host table entr
you will run the CFGTCO
to create a route
d Host Name
host
52 78413025-001

Configuring AS/400 for Printing

The procedure for that you:
1. Setup the printing capability
2. Verify the setup w
In order to accomplish this configuration, you need following information:
a) Remote Printer Queue Name
Set for any of ‘pr1’ through ‘pr4’.
The Remote Printer Queue name must be all lower case.
b) IP Address
See the IP Address value set in the INIT IP ADDRESS parameter of the LAN INTERFACE item in the Power-On Configuration setup you find in the User Manual included in the Printer Documentation & Driver CD­ROM.
configuring an AS/400 for printing requires
ith a print job.
the

Setting up Printing for ASCII Files

The next step in configuring the AS/400 is to setup the remote printing capability. There are two ways to do this:
you can specify the LPR parameters manually each
time you send a file to the printer.
use remote writer and a remote output queue for
automatic printing to the printer.
784103025-001 53
y
TToo UUssee LLPPRR MMaannuuaalllly
1. Start TCP/IP, if it not already running, b STRTCP command
2. At
3. The following example shows
the AS/400 command line, enter ‘LPR’.
need to specify:
only the parameters you
y entering the
Remote System
Printer Queue
Dest
Transform SCS to ASCII
Manufacture Model
Internet Address
where,
Remote
INTNETADR, which then prompts you to specify the IP address of your printer.
Printer Queue: set to “pr1” through “pr4”. The remote printer queue name must be all lower case, entered in single quotes.
Destination Type: specify “OTHER” for the parameter.
Transform: specify “YES”. Manufacturer Type and Model: select a manufacturer type and
model. Select “IBM6400EP” for Epson emulation or “IBM or “IBM42023” for IBM Proprinter.
Internet Address: specify the IP address of the printer.
System: enter the host name of your printer or
r Type and
RMTSYS
PRTQ
DESTTYP
TRANSFORM
MFRTYPMDL
INTNETADR
INTNETADR
d1prn
OTHER ination Type
YES
IBM6400EP
127.000.000.000.
DESTTYP
6400”
54 78413025-001
TToo CCrreeaattee aann AAuuttoommaattiicc RReemmoottee OOuuttppuutt QQuueeuuee
1. From the AS/400 command line, enter
2. The following exam
ple shows only the parameters you
CRTOUTQ.
need to specify:
Output Queue Remote system Remote printer queue Writer to Autostart Connection type Destination type Transform Manufacturer type Internet Address
w
here,
Output q
ueue: enter the name of the AS/400 output queue.
OUTQ
RMTSYS
RMTPRTQ
AUTOSRTWTR
E CNNTYP
DESTTYP
TRANSFORM
MFRTYPMDL
INTNETADR
USERNAME INTNETADR d1prn 1 IP XAUTOQXAIX YES IBM6400EP
127.000.000.000.
Remote System: enter the host name of your printer or INTNETADR, which then prompts you to specify the IP address of your printer.
Remote Printer Queue: set to “pr1” through “pr4”. The remote printer queue name must be all lower case, entered in single quotes.
Writer to Autostart: set the value to “1”. Connection Type: specify th
is value as “IP”.
Destination Type: specify “XAUTOQXAIX”. Transform: specify “YES”. Manufacturer Type: select a manuf
Select “IBM6400EP” for Epson emulation or “IBM640 “
IBM42023” for IBM Proprinter.
acturer type and model.
0PR” or
Internet Address: specify the IP address of the printer.
784103025-001 55
M n te Pro itoring Printer & Remo inter
Configuration
The following procedu B itoring the sta he netw nd
rowser for mon tus of t ork printer a
for the printer remote configura eed a
1. ter web r t ddress as
To browse the prin page, ente he IP A
web page address
T correspond w dres t in the INIT IP
he IP Address must ith the IP Ad s se
ADDRESS parameter of the LAN I iteNTERFACE m, see the User
Manual included in the Printer D n & ocumentatio Driver CD-ROM.
The “Printer Web Page” sc
re describes the use of the Internet
tion. Proc s follows:
.
reen appears:
This Printer Web Page contain information about network printers:
Printer Configuration: current printer status that you can configure by remote control.
Printer Status: current ribbon and print head life.
56 78413025-001
s the following types of
rinter Reset: feature to reboot the printer.
P
roduct support: reference to contact Compuprint.
P
You can select the and
Product Support screens to see the corresponding pages
described in the following sections.
P Status, Printer Reset
rinter Configuration, Printer
rinP ter Configuration
To obtain the Printer Configurati the Printer Configuration button. The following screen appears:
This page contains a series of tables with the corresponding printer set-up: for a detailed description of the parameters and values contained in the Configuration and Macro Menus refer to the User Manual.
on information tables, click on
784103025-001 57

NIC Setup

When pressing the Interface button the following screen appears:
58 78413025-001
You can now choose the network printer configuration. When the parameters are set as necessary, click on the Submit button at the end of the table. If a password has already been set in the Security item, to enter the remote printer configuration mode, you need to type the network password.
The User Name is : root The default password is : root

System Setting

Click on the System button. The following page appears:
You can now choose between loading the default factory setting overwriting the current parameters and setting the security password.
784103025-001 59

Setting the Security Password

In the System page, click on the Security Settings button. The first time the following screen appears:
Type the User Name (root) and the password (root) and button. The following screen appears:
OK
60 78413025-001
It is now possible to indicate a password to protect the setting. Click on the
Submit button, the following screen appears:
Remind yo
eset Printer page to save the changes.
R
u, that it is necessary to select
Reboot Printer in the
784103025-001 61

FCC Notes

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operations of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

ICES-003/NMB-003 Notes

.
TThhiiss CCllaassss AA ddiiggiittaall aappppaarraattuuss ccoommpplliieess wwiitthh CCaannaaddiiaann IICCEESS--000033.
Cet appareil numérique de la classe A est confor Canada.
me à la norme NMB-003 du

EEC Regulations

This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.
This equipment is in compliance with the essential requirements and other relevant provisions of the UE Directives 89/336, 73/23, 92/31, 93/68.
62 78413025-001
Loading...