Comnet CL-SFP1, CL-SFP3, CLRJ2COAX Specsheet
Small Form-Factor Pluggable
Copper Range Extender Module
CL-SFP
EXTENDER
The ComNet™ CopperLine® CL-SFP is a small form-factor pluggable Ethernet extender
module that improves bandwidth and distance of existing copper networks. It helps
avoid installation costs of new fiber lines on site by allowing full 10 Mbps or 100 Mbps
Ethernet bandwidth to be extended over 2-wire twisted pair or coaxial cable.
Housed in a small form-factor pluggable (SFP) module enclosure, it is designed for
plug-and-play installation into any 100BASE-FX Ethernet unit with an MSA-compliant
port. These must be used in pairs, with a CL-SFP module installed at both ends of the
connection, or a CopperLine unit installed at one end.
FEATURES
› Extends Ethernet up to 3,000 feet (914 m) at 10 Mbps or
1,000 feet (305 m) at 100 Mbps over 1 pair UTP cable.
› Extends Ethernet up to 5,000 feet (1,524 m) at 10 Mbps or
2,000 feet (610 m) at 100 Mbps over Coaxial cable using the
optional CLRJ2COAX or CLRJ2COAXCAB adapters.
› Automatic local/remote device selection ensures ultimate
flexibility and ease of use.
› Small Form-Factor Pluggable (SFP) module can be
plugged into any Ethernet switch with SFP ports that
support 100BASE-FX*
› Tested and certified by an independent laboratory for full
compliance with the environmental requirements (ambient
operating temperature, mechanical shock, vibration, humidity
with condensation, high-line/low-line voltage conditions
and transient voltage protection) of NEMA TS-1/TS-2 and
CALTRANS Traffic Signal Control Equipment Specifications
› Lifetime Warranty
APPLICATIONS
› Retrofit existing analog CCTV installations to
Ethernet-based systems
› CCTV systems for Casinos, airports, school campuses
* The ComNet Copperline CL-SFP modules are fully compatible with
all ComNet Ethernet products supporting 100BASE-FX SFP modules.
The modules cannot be used in ports that only support 1000BASE-FX
SFP modules.
Please contact ComNet technical support before purchasing this
product if you intend to use it with any other 3rd party manufacturer
in order to check compatibility.
LIFETIME WARRANTY WWW.COMNET.NET TECH SUPPORT: 1.888.678.9427
CL-SFP
Small Form-Factor Pluggable
Copper Range Extender Module
INSTALLATION & OPERATION
CL-SFP is a book-end solution that can work only with an additional CL-SFP or
ComNet™ CopperLine® unit.
Follow the instructions below to install and connect CL-SFP:
Plug one of the two CL-SFP into the 100BASE-FX SFP slot of a device/switch. Repeat
this step for the second CL-SFP in the pair.
Connection
Connect CL-SFP devices using a twisted 2-wire cable (use pins 1 & 2) or Coax
Always connect CL-SFP to another CL-SFP device or a ComNet™ CopperLine® unit. If an
CL-SFP was connected to a regular port of any Ethernet device, such as a switch, reset
the CL-SFP by unplugging and re-inserting the unit.
Link synchronization may take up to one minute.
LED Indicators Use 100BaseTX LED on the host
Distance figures are obtained using in-house testing mirroring
installations. Factors such as coaxial and copper cable quality, the
number of connectors and splices in the cable run, and environmental
conditions encountered within the installation might affect the actual
transmission distance and should be taken into consideration.
SPECIFICATIONS
Interface
Type 100BaseTX
Connector SFP / MSA Compliant
Connectors RJ-45
Data Rate 10 or 100 Mbps
Mechanical
Operating Voltage 3.3 V
Power Consumption 1 W Max
Dimensions (H x W x L) 0.48 × 0.55 × 2.91 in (12.4 × 14.0 × 74.1 mm)
Weight 1.06 oz (30.0 g)
Environmental
Operating Temp -40°C to +75°C
Storage Temp -40°C to +85°C
Relative Humidity 0 to 90%, non-condensing
ORDERING INFORMATION
Part Number Description
CL-S FP1 10 Mbps Copper Range Extending SFP
CL-S FP3 100 Mbps Copper Range Extending SFP
CLRJ2COAX Adapter for RJ-45 to COAX
CLRJ2COAXC AB Adapter Cable for RJ-45 to Coax
CLESP Single Port Ethernet Surge Protector
Optional Accessories RJ-45 Breakout Wiring Kit (Includes cable and terminal block)
TYPICAL APPLICATION
Network Switch Network Switch
Install into
SFP Port
Network Switch Network Switch
Install into
SFP Port
UTP/Coax
CL-SFP CL-SFP
CL-SFP
Extended Distance
UTP/Coax
Extended Distance
CopperLine
Extender
Install into
SFP Port
3 CORPORATE DRIVE
8 TURNBERRY PARK ROAD
|
DANBURY, CONNECTICUT 06810
|
GILDERSOME
|
MORLEY
|
|
USA
T: 203.796.5300
|
LEEDS, UK LS27 7LE
|
F: 203.796.5303
|
T: +44 (0)113 307 6400
|
TECH SUPPORT: 1.888.678.9427
|
F: +44 (0)113 253 7462
|
INFO-EUROPE@COMNET.NET
|
INFO@COMNET.NET
30 Mar 2015© 2015 Communic ation Networ ks. All Right s Reserve d. “ComNet ” and the “ComNe t Logo” are regis tered tra demarks of Comm unication Net works.
Loading...