Code 3 CW2450, CW2451 Installation & Operation Instructions

!

Installation and Operation Instructions

CW2450 & CW2451 LED WORKLAMPS

CODE3 INC. CW2450 and CW2451 LED Worklamps feature a fully
adjustable mounting bracket that allows it to be rotated 360º as well
as angled upwards or downwards. A convenient (removable) handle
made of reinforced nylon allows easy repositioning. Other features
include an aluminum heatsink housing, tough polycarbonate lens,
on/off switch and nine 3-watt LEDs that produce a high-intensity
beam. These worklamps are designed to perform in the harshest

of work environments and offer all the benets of LED technology

including the brightest white light output, a long, maintenance-free
service life and extremely low current consumption.

IMPORTANT! Read all instructions before installing and using. Installer: This manual must be

delivered to the end user. CODE 3 is not responsible for the misuse of our work light products by un­authorized personnel.

WARNING!

Failure to install or use this product according to manufacturer’s recommendations may result in property
damage, serious bodily/personal injury, and/or death to you and those you are seeking to protect!

Do not install and/or operate this safety product unless you have read and understand the safety
information contained in this manual.

1. Proper installation combined with operator training in the installation, use, care and maintenance of vehicle equipment accessories is
essential to ensure the safety of you and those you are trying to protect.

2. Exercise caution when working with live electrical connections.

3. This product must be properly grounded. Inadequate grounding and/or shorting of electrical connections can cause high

current arcing, which can cause personal injury and/or severe vehicle damage, including re.

4. Proper placement and installation are vital to the performance of this worklamp. Install this product so that output
performance of the system is maximized and the controls are placed within convenient reach of the operator so that s/he can
operate the system without losing eye contact with the work area.

5. It is the responsibility of the vehicle operator to ensure during use that all features of this product work correctly. In use, the
vehicle operator should ensure the projection of the beam is not blocked by vehicle components (i.e., open trunks
or compartment doors), people, vehicles, or other obstructions.

6. The manufacturer assumes no liability for any loss resulting from the use of this device.

SAA

NOTE: Black die cast Aluminum housing gets very hot to the touch after operating constantly for several hours.

Specications:

Input Voltage: 12-36 VDC

Input Current: 2.2 Amps @ 12VDC

Weight: 2.2 lbs. approx.

Output Power (Lumens): 1300 (Raw)
1100 (Effective)

T13795 REV. 1

Installation Instructions:

1. Select a mounting location for the unit on a at surface. Place the
unit base, at side down, on the surface.

2. Use the four holes in the base to mark the drill locations for
mounting. It may be necessary to remove the light head from the
base by turning the base handle counter-clockwise until the head
can be removed. For reference, the mounting holes are 50mm x
30mm square, center-to-center.

3. Drill four 5.5mm diameter through holes through the mounting
surface. Align the base with the mounting holes and place the M5
hex head bolts through the base and the holes. Place a washer
on the other end of the bolt and tighten with the M5 nut. Repeat
for the other three bolts.

4. Place the light head back in the base and turn the handle clock
wise until the head is captured. Position the light in the
appropriate direction and fully tighten using the handle.

Page 1 of 2

Wiring Instructions:

Black Wire: Ground
Red Wire: Connect to fused power

See wiring diagram for further instruction

Manufacturer Limited Warranty and Limitation of Liability:

Manufacturer warrants that on the date of purchase this product will conform to Manufacturer’s specications for this product (which are available from the
Manufacturer upon request), and Manufacturer further warrants that this product is free from defects in materials and workmanship. This Limited Warranty
extends for 36 months from the date of purchase. Other warranties may apply, call Manufacturer for details. Manufacturer will, at its discretion, repair or
replace any product found by the Manufacturer to be defective and subject to this Limited Warranty.

DAMAGE TO PARTS OR PRODUCTS RESULTING FROM TAMPERING, ACCIDENT, ABUSE, MISUSE, NEGLIGENCE, UNAPPROVED MODIFICATIONS, FIRE OR
OTHER HAZARD; IMPROPER INSTALLATION OR OPERATION; OR NOT BEING MAINTAINED IN ACCORDANCE WITH THE MAINTENANCE PROCEDURES SET
FORTH IN MANUFACTURER’S INSTALLATION AND OPERATING INSTRUCTIONS VOIDS THIS LIMITED WARRANTY.

ORAL STATEMENTS OR REPRESENTATIONS ABOUT THE PRODUCT WHICH MAY HAVE BEEN MADE BY SALESPEOPLE, DEALERS, AGENTS OR OTHER
MANUFACTURER’S REPRESENTATIVES DO NOT CONSTITUTE WARRANTIES. THIS LIMITED WARRANTY MAY NOT BE AMENDED, MODIFIED, OR EN­LARGED EXCEPT BY A WRITTEN AGREEMENT SIGNED BY AN AUTHORIZED OFFICIAL OF MANUFACTURER WHICH EXPRESSLY REFERS TO THIS LIMITED

WARRANTY.

Exclusion of Other Warranties: MANUFACTURER MAKES NO OTHER WARRANTIES, EXPRESS OR IMPLIED. THE IMPLIED WARRANTIES

FOR MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY EXCLUDED AND SHALL NOT APPLY TO THE PRODUCT. BUYER’S SOLE
AND EXCLUSIVE REMEDY IN CONTRACT, TORT, OR UNDER ANY OTHER THEORY AGAINST MANUFACTURER REGARDING THE PRODUCT AND ITS USE
SHALL BE THE REPLACEMENT OR REPAIR OF THE PRODUCT AS DESCRIBED ABOVE.

Limitation of Liability: IN THE EVENT OF LIABILITY FOR DAMAGES ARISING OUT OF THIS LIMITED WARRANTY OR ANY OTHER CLAIM

RELATED TO THE MANUFACTURER’S PRODUCTS, MANUFACTURER’S LIABILITY FOR DAMAGES SHALL BE LIMITED TO THE AMOUNT PAID FOR THE
PRODUCT AT THE TIME OF THE ORIGINAL PURCHASE. IN NO EVENT SHALL MANUFACTURER BE LIABLE FOR LOST PROFITS, THE COST OF SUBSTITUTE
EQUIPMENT OR LABOR, PROPERTY DAMAGE, OR OTHER SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES BASED UPON ANY CLAIM FOR BREACH
OF CONTRACT, IMPROPER INSTALLATION, NEGLIGENCE, OR OTHER CLAIM, EVEN IF MANUFACTURER OR A MANUFACTURER’S REPRESENTATIVE HAS
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. MANUFACTURER SHALL HAVE NO FURTHER OBLIGATION OR LIABILITY WITH RESPECT TO THE
PRODUCT OR ITS SALE, OPERATION AND USE, AND MANUFACTURER NEITHER ASSUMES NOR AUTHORIZES THE ASSUMPTION OF ANY OTHER OBLIGA­TION OR LIABILITY IN CONNECTION WITH SUCH PRODUCT.

This Limited Warranty denes specic legal rights. You may have other legal rights which vary from state to state. Some states do not allow the exclusion or
limitation

10986 North Warson Road

St. Louis, MO 63114

Customer Service

[phone]

[e-mail]

www.code3esg.com

A Division of ESG

|

www.eccogroup.com

©2015 CODE 3 INC.

T13795 Rev. 1 Page 2 of 2