Code 3 CommandStik MR6MC Installation & Operation Manual
Installation and Operation Instructions
MR6MC COMMANDSTIK
UNIVERSAL SUV VERSION
MR6MC COMMANDSTIK 2011+ DODGE
CHARGER VERSION
Installation & Operation Manual
CommandStik™ With
MR6MC Light Heads
Interior Lighting System
CONTENTS:
Introduction: CommandStik With MR6MC
Light Heads
The CommandStik with MR6MC Multi Color Tech-
nology is an interior lighting system that ts in the
rear deck area. The CommandStik has room for up
to six MR6MC Multi Color light heads.
Introduction................................................................1
Product Specications................................................1
Unpacking & Pre-Installation......................................2
Installation & Mounting - Universal............................2
Installation & Mounting - 2011+ Dodge Charger.....3-4
Wiring Instructions......................................................5
Flash Pattern Selection..............................................6
Troubleshooting..........................................................7
Exploded View-Parts List...........................................7
Warranty.....................................................................8
Product Specications:
MR6MC Light Head Options: Red/Amber, Blue/Amber
Size Full Unit:------27.50” long X 1.25” tall X 3.50” deep------------------------------------------------------------------------Weight: 4.5 lbs
Input Voltage: ---------------------------------------------------------------------------------------------------------------------------------------12VDC
Input Current: Startup Current-------------------------------------------------------------------------------------------------------------0.007 Amps
Current @ Power-----------------------------------------------------------------------------------------------------------------------------0.005 Amps
Max Current----------(6) Light Hd ---------------------------------------------------------------------------------------------------------11.30 Amps
Mounting Hardware - All mounting hardware is packed in a small bag inside the main carton. There are two
brackets used to mount the CommandStik to the vehicle. These are discussed in detail later.
920-0546-00 Rev. A
Page 1 of 8
Unpacking & Pre-installation
Carefully remove the CommandStik and place it on a at surface, taking care not to scratch the lenses or damage the cable
coming out of the unit. Examine the unit for transit damage, broken lamps, etc. Report any damage to the carrier and keep
the shipping carton.
Standard units are built to operate on 12 volt D.C. negative ground (earth) vehicles. If you have an electrical system other
than 12 volt D.C. negative ground (earth), and have not ordered a specially wired light bar, contact the factory for instructions.
Test the unit before installation. To test, touch the black wire to the ground (earth) and the other wires to +12 volts D.C., in accordance with the instructions attached to the cable (an automotive battery is preferable for this test). A battery charger may
be used, but note that some electronic options may not operate normally when powered by a battery charger. If problems
occur at this point, contact the factory. Note: Before beginning the installation process, be absolutely certain that the
Light Bar functions as desired (See page 4 & 5 for options)!
IMPORTANT! Read all instructions before installing and using. Installer: This manual must be delivered to the end user.
WARNING! Failure to install or use this product according to manufacturers recommendations may result in
1. Proper installation combined with operator training in the use, care, and maintenance of emergency warning devices are essential to
ensure the safety of emergency personnel and the public.
2. Emergency warning devices often require high electrical voltages and/or currents. Exercise caution when working with live electrical
connections.
3. This product must be properly grounded. Inadequate grounding and/or shorting of electrical connections can cause high current arcing,
which can cause personal injury and/or severe vehicle damage, including re.
4. Proper placement and installation is vital to the performance of this warning device. Install this product so that output performance of the
system is maximized and the controls are placed within convenient reach of the operator so that s/he can operate the system without losing
eye contact with the roadway.
5. It is the responsibility of the vehicle operator to ensure daily that all features of this product work correctly. In use, the vehicle operator
should ensure the projection of the warning signal is not blocked by vehicle components (i.e., open trunks or compartment doors), people,
vehicles or other obstructions.
6. The use of this or any other warning device does not ensure all drivers can or will observe or react to an emergency warning signal. Never
take the right-of-way for granted. It is your responsibility to be sure you can proceed safely before entering an intersection, drive against
trafc, respond at a high rate of speed, or walk on or around trafc lanes.
7. This equipment is intended for use by authorized personnel only. The user is responsible for understanding and obeying all laws regarding
emergency warning devices. Therefore, the user should check all applicable city, state, and federal laws and regulations. The manufacturer
assumes no liability for any loss resulting from the use of this warning device.
property damage, serious injury, and/or death to those you are seeking to protect!
Do not install and/or operate this safety product unless you have read and understand the safety information
contained in this manual.
WARNING! When drilling into any vehicle surface, make sure that the area is free from any electrical
wires, fuel lines, sensors, vehicle upholstery,etc. that could be damaged.
Installation Instructions: Universal Version
Step 1 Assemble the mounting brackets to the CommandStik with the the supplied 1/4"-20 screws and internal tooth
lock washers and tighten the screws nger tight (see page 7 exploded view for orientation).
Step 2 Using the CommandStik assembly as a template, locate the CommandStik in the desired location for the light
bar in the vehicles rear deck area and mark the location of the customer supplied carriage bolts using the square holes
in the CommandStik 90 degree mounting brackets. Note: The square holes in the CommandStik's 90 degree mounting
brackets are sized for 1/4-20 carriage bolts.
Step 3 Drill the required mounting holes through the vehicles fabric and sheet metal to provide a hole for the customer
supplied mounting bolts. Note: in many cases some sort of spacer will be required between the vehicle's fabric
and it's sheet metal to keep the fabric from collapsing as you tighten the hardware. The spacer should be made
out of a suitable plastic or metal for safety.
Step 4 Install the customer supplied carriage bolts, washers and lock washers through the square holes in the Com-
mandStik's 90 degree mounting brackets and through the holes in the vehicle's rear deck fabric and sheet metal and
tighten all fasteners securely.
Caution: Drilling into the housing of the light bar could damage wiring or other internal components.
920-0546-00 Rev. A
Page 2 of 8
Installation Instructions: 2011+ Dodge Charger Version
Step 1 Fasten the CommandStik Mounting Brackets with the the supplied 1/4"-20 X 3/8” long screws, 1/4” internal tooth
lock washers, & 1/4” at washers and tighten the screws nger tight (see Figure 1 below for bracket orientation). Make sure
you thread the screws into the inner mounting holes in the brackets as shown.
Step 2 Remove the (2) outer child restraint covers shown in Figure 2 on page 4. Position the CommandStik in the rear deck
of the vehicle with the mounting brackets positioned in the child restraint pockets and align the threaded holes in the mounting brackets with the existing holes in the vehicle. See Figure 3 on page 4.
Step 3 Remove the fabric cover from inside the vehicle’s trunk, thread a supplied 1/4”-20 X 5/8” Phillips Pan Head Machine
Screw with a 1/4” internal tooth lock washer, & 1/4” at washer through the existing hole in the child restraint area & into the
threaded holes in the Pemserts in each of the CommandStik Mounting Brackets (see Page 5 Figure 4). Leave the screws
just slightly loose. Note: It is extremely helpful to have an assistant line up and hold the CommandStik’s Mounting
Brackets in location to prevent movement while you are threading the screws into the holes.
Step 4 Center the CommandStik in the rear deck area and tighten all of the screws. Replace the fabric cover inside the
vehicle’s trunk & snap the round plastic plugs into the holes in the top of the CommandStik to plug the holes.
Caution: Drilling into the housing of the light bar could damage wiring or other internal components.
Step 5 To replace the plastic child restraint covers you will have to trim the covers to clear the CommandStik’s Mounting
Brackets then re install the covers.
1/4"-20 X 3/8" LONG
PHILLIPS PAN
HEAD SCREW
1/4" INTERNAL
TOOTH LOCK
WASHER
PLASTIC
HOLE PLUG
1/4" FLAT
WASHER
MOUNT TO
INNER MOUNTING
BRACKET HOLES
UNDER SIDE VIEW
1/4"-20 X 5/8" LONG
PHILLIPS PAN
HEAD SCREW
TOP SIDE VIEW
920-0546-00 Rev. A
FIGURE 1
Page 3 of 8
Loading...