Cobra CPP15000 User Manual
The Cobra line of quality products includes:
CB Radios
Dash Cams
Radar Detectors
Marine VHF Radios
Power Inverters
Accessories
www.cobra.com
CPP15000
JumPack XL H2O User Manual
Portable Power - Anytime, Anywhere!
Thank you for purchasing the Cobra CPP15000 JumPack
XL H2O portable jump starter powerpack. Before using
this product, please read these instructions carefully to
learn about the features and capabilities of the JumPack
XL H2O and how to get the best performance.
Note: Please charge your CPP15000 JumPack XL H2O
completely prior to using it for the rst time.
©2017 Cobra Electronics Corp. Part No. 480-1098-P Printed in China Version A
™
IMPORTANT SAFETY INSTRUCTIONS
Precautions when working with the JumPack XL H2O:
WARNING: Keep the unit clear of fire and water.
WARNING: Shock Hazard. Keep away from children. Do not
insert foreign objects into the Jump Start Cable Output, the
USB Output Port, or the Charge Adapter Input Jack. Do not
submerge this product in water, expose to rain, snow,
condensation, or spray for long periods. Do not open the
JumPack XL to replace the internal battery. There are no user
replaceable parts inside the JumPack XL H2O.
WARNING: Explosion Hazard. Do not use this product where
there are flammable fumes or gases, such as an inadequately
vented bilge of a boat or near propane tanks. Do not use this
product in an enclosure containing automotive-type lead-acid
batteries.
WARNING: Fire Hazard
Do not crush or puncture.
Caution: Operating temperature
Do not expose to temperatures over +113° F (+45° C) or under -14° F
(-10° C). Using at high or low temperatures may reduce the internal
battery capacity and shorten the battery life.
Note: In extreme cold weather conditions, please store indoors for
best results.
The JumPack XL H2O is supplied with a rechargeable Li-Cobalt battery.
This battery is self-contained and not consumer replaceable. The unit
and battery must be disposed of properly when it no longer holds a
charge. Proper charging practices will increase the life of the batteries.
For information on battery recycling call toll free 800-822-8837.
Precautions when working with vehicle batteries:
WARNING: Explosion and fire hazard
1.
Follow all instructions published by the battery manufacturer and the
manufacturer of the equipment in which the battery is installed.
2. Make sure the area around the battery is well-ventilated.
3. Never smoke or allow a spark or flame in the vicinity of the
engine or batteries.
4. Be careful not to drop a metal object on the battery or allow a
metal tool to simultaneously touch the positive and negative
cable ends or battery terminals.
5. Remove personal metal items such as rings, bracelets,
necklaces, and watches when working with batteries. Batteries
produce a short-circuit current high enough to weld a ring or
other similar objects to metal, causing a severe burn.
6. If you need to remove a battery, always remove the negative
terminal from the battery first. Make sure all accessories are
off to prevent causing a spark.
7. Someone should be within range of your voice, or close enough
to come to your aid when you work near batteries.
8.
Have plenty of fresh water, soap and a supply of baking soda on
hand in the area of the batteries in case of contact with battery
acid. Baking soda neutralizes lead acid battery electrolyte.
2 3
Product:
Tri-Color Status LED
Battery Level
Light Bar
USB 5V 3A
Outputs
LED Flashlight
Charge Adapter
CHARGE
INPUT
Car Charger
Output
3 AMP USB
OUTPUT
JUMPSTART
CAR CHARGER
OUTPUT
Jump Start Cable
Output
Input
Flashlight/Battery
Charge Level Button
Direct-to-Battery
Jump Start Cable
Car Charger Cable
with Clamps
AC
Adapter
4 5
Jumpack Charge
Adapter Cable
Operation:
Recharging the JumPack:
Battery Level Light Bar
Flashlight/Battery
Charge Level Button
The CPP15000 JumPack can be recharged with the included Car Charger
Cable and JumPack Charge Adapter Cable or with the included AC Adapter.
When the JumPack is charging, the light bar will show the current battery
charge level. The last section of the light bar that is lit will blink to show
that the JumPack is charging and turn off automatically when the
JumPack is fully charged.
For best battery performance the JumPack should be fully recharged
every 3 months.
Caution: Operating temperature
Do not expose to temperatures over +113° F (+45° C) or under +14°
F (-10° C). Using at high or low temperatures may reduce the internal
battery capacity and shorten the battery life.
Note: In extreme cold weather conditions, please store indoors for
best results.
3 AMP USB
OUTPUT
CHARGE
OR
INPUT
CAR CHARGER
JUMPSTART
OUTPUT
Note: When charging a device(s) the charge level may be
lower than the actual battery charge level because the
JumPack cannot accurately measure the charge level
during rapid charging. To confirm the actual battery
charge level, disconnect the device(s) being charged and
press the button.
NOTES: The JumPack is designed for gasoline and diesel
powered passenger cars and light duty trucks in good working
1st Section on: 10%-40% charge
2nd Section on: 40%-65% charge
3rd Section on: 65%-85% charge
4th Section on: 85%-100% charge
order and with batteries that are not damaged but require
assistance commonly due to leaving lights on, cold
temperature, sitting unused for limited periods of time.
Check Battery Charge Level:
To check the battery charge level, press the Flashlight/Battery Charge
Level Button on the top of the unit with no device connected.
The green Battery Level Light Bar will show the remaining
battery charge level:
6 7
The JumPack uses a special high current battery to provide
up to 600 peak amps to start your engine. It can provide
400 amps starting current to jump start up to 3 cars on one
charge. After this, the unit must be recharged.
The JumPack is intended to jump start a vehicle with a
battery that is not completely discharged.
Starting a vehicle by connecting directly to the battery:
Tri-Color Status LED:
The Status LED will illuminate and the color will change
if the following conditions are present:
Jump Start:
START
1
. For best results, make sure the JumPack is fully charged.
2. Turn off all vehicle accessories.
3.
Connect the Jump Start Cable to the JumPack
(the LED will
turn RED).
4. Connect the RED clamp to the POSITIVE post of the battery.
5.
Connect the BLACK clamp to the NEGATIVE post of the battery.
6.
Check the Tricolor Status LED. When the LED is
GREEN the JumPack is ready to start the vehicle.
7.
Start the vehicle.
NOTE: If your vehicle does not start after 3 attempts,
call a mechanic.
When the engine starts:
1. Disconnect the Jump Start Cable from the JumPack and
the vehicle battery.
2. Leave the engine running for at least twenty minutes to
allow the vehicle’s battery to recharge.
If the engine does not start:
LED CONDITION
No LED
depleted. Check the
level and verify the connection of the Jump Start
Cable to the
Red FLASH Reverse the clamps.
Connection not detected or the JumPack battery is
JumPack
battery charge
JumPack
.
Reverse polarity connection.
Red FLASH and FLASH GREEN LIGHT BAR T
nearly depleted. Charge the JumPack.
Yellow FLASH - The JumPack is transferring
charge to the vehicle’s battery.
Wait for the LED to turn GREEN.
Yellow SLOW FLASH - JumPack internal battery is
too hot for a safe jump start attempt. Wait for the
battery to cool down and the LED to turn GREEN.
Green The JumPack is ready to help start
your vehicle.
he JumPack internal battery is
NOTE: The JumPack will make a clicking sound every 5
seconds. This is part of normal operation.
• The LED may flash YELLOW. Wait for the LED to turn
GREEN and try again starting with step 6.
8 9
Starting a vehicle using the accessory 12V port
inside the vehicle:
1
. For best results, make sure the JumPack is fully charged.
3 AMP USB
OUTPUT
CHARGE
INPUT
JUMPSTART
CAR CHARGER
OUTPUT
2. Turn off all the vehicle accessories.
3. Disconnect the JumPack Charge Adapter Cable from the
JumPack Car Charger Cable.
4.
Connect the Car Charger Cable to the JumPack
(the LED will turn RED)
.
5. Turn the ignition switch to the Accessory position.
6. Connect the plug to the 12 Volt accessory port of the vehicle
(once car charging begins,
the LED will flash YELLOW)
.
8. Wait for the LED to turn GREEN.
9. Start the vehicle.
If the engine starts:
1. Disconnect the Car Charger Cable from the 12V accessory port
and from the JumPack.
2. Leave the engine running for at least twenty minutes to
Tri-Color Status LED:
The Status LED will illuminate and the color will change
if the following conditions are present:
LED CONDITION
No LED
depleted. Check the
level and verify the connection of the Car Charger
Cable to the
Red Car charging failed. Check that the vehicle ignition
switch is in Accessory position.
Red FLASH JumPack to charge it sufciently. Try a jumpstart with
the clamps and direct-to-battery method.
Red FLASH and FLASH GREEN LIGHT BAR T
nearly depleted. Charge the JumPack.
Yellow FLASH - The JumPack is charging the car battery.
Wait for the GREEN LED before attempting to
jumpstart.
Connection not detected or the JumPack battery is
JumPack
battery charge
JumPack
.
The vehicle battery is too discharged for the
he JumPack internal battery is
Yellow FAST FLASH - Charging almost complete.
Green Try to start your vehicle.
allow the vehicle’s battery to recharge.
NOTE: The car charging will take up to 15 minutes. If your
vehicle does not start with the inside the car method try to
jump start with the direct-to-batery method.
10 11
NOTE: The JumPack will make a clicking sound every 5
seconds. This is part of normal operation.
Charging a 5V USB Device:
To charge a 5V USB device, connect the device’s cable to either of
the JumPack’s two USB Outputs.
The JumPack will turn on and start charging the device
automatically. The green light bar will indicate that the device
is charging.
Once the device reaches its charge capacity and ceases charging,
the light bar will turn off.
NOTE: If the tri-color status LED turns RED while it’s charging,
there is a problem and connected devices will not charge.
Try reconnecting the device(s) or using a different cable(s).
3 AMP USB
OUTPUT
CHARGE
INPUT
LED Flashlight:
1. Press and hold the Flashlight/Battery/Charge Level Button for 3
seconds to turn on the LED flashlight.
2. Press again to activate the strobe function.
3. Press again to activate the SOS function.
4. Press again to turn Off.
CAR CHARGER
JUMPSTART
OUTPUT
Product Features:
• Lithium Cobalt rechargeable battery.
• 400 Amp Starting Current / 600 Amp Peak Current.
• Dual 5V/3 Amp USB Outputs for rapid charging of portable devices.
• High Intensity LED flashlight, strobe and SOS .
Rechargeable by Car Adapter or 120 VAC Wall Adapter.
•
•
UL2743 Certified
Product Specification:
• Li-Cobalt rechargeable battery: 14.8V/44.4Wh
• Size: 7.25” x 3.97” x 1.62”
• Weight: 1.50 lbs.
• Recharge time: 4 hours
• Starting/Peak Current: 400 Amps/600 Amps
• USB Output: 5V 3 Amps each
• Car Charger Output: 15V 10 Amps
• Charge Input: 13.0 ~ 16.0VDC 1 Amp
12 13
FCC Statement:
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates uses and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/television technician
for help.
WARNING: Any modifications made to this device that are not expressly
approved by party responsible for compliance could void the user’s authority
to operate this device.
®
Cobra
and the snake design are registered trademarks of
Cobra Electronics Corporation, USA.
Cobra Electronics Corporation™ is a trademark of Cobra
Electronics Corporation, USA.
PROPOSITION 65 WARNING: This product contains a chemical known to
the State of California to cause cancer and birth defects or other
reproductive harm.
Limited 1-Year Warranty:
For Products Purchased in the U.S.A.
Cobra Electronics Corporation warrants that its Cobra CPP15000
JumPack XL H2O Charger, and the component parts thereof, will be free of
defects in workmanship and materials for a period of one year from the
date of first consumer purchase. This warranty may be enforced by the first
consumer purchaser, provided that the product is utilized within the U.S.A.
Cobra will, without charge, repair or replace, at its option, defective
products or component parts within the warranty period upon delivery to
the Cobra Factory Service Department, accompanied by proof of the date
of first consumer purchase, such as a duplicated copy of a sales receipt.
You must pay any initial shipping charges required to ship the product
for warranty service, but the return charges will be at Cobra’s expense,
if the product is repaired, this warranty gives you specific rights, and
you may also have other rights which vary from state to state.
Exclusions: This limited warranty does not apply:
1. To any product damaged by accident.
2. In the event of misuse or abuse of the product, or as a result of
unauthorized alterations or repairs.
3. If the serial number has been altered, defaced or removed.
4. If the owner of the product resides outside the U.S.A.
All implied warranties, including warranties of merchantability and
fitness for a particular purpose are limited in duration to the length of
this warranty.
Cobra shall not be liable for any incidental, consequential or other
damages; including, without limitation, damages resulting from loss of
use or cost of installation.
Some states do not allow limitations on how long an implied warranty
lasts and/or do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitations may not apply to you.
For Products Purchased Outside The U.S.A.
Please contact your local dealer for warranty information.
14 15
Product Service:
For any questions about operating or installing this new Cobra
product, or if parts are missing…PLEASE CALL COBRA
FIRST…do not return this product to the store. If this product
should require factory service, please call Cobra before sending the
product. This will ensure the fastest turn-around time on any repair.
If Cobra asks that the product be sent to its factory, the following
must be furnished to have the product serviced and returned:
For Warranty Repair include some form of proof-of-purchase,
1.
such as a mechanical reproduction or carbon of a sales receipt.
Make sure the date of purchase and product model number are
clearly readable. If the originals are sent, they cannot be returned.
2. Send the entire product.
3. Enclose a description of what is happening with the product.
Include a typed or clearly printed name and address of where
the product is to be returned, with phone number (required
for shipment).
4. Pack product securely to prevent damage in transit. If possible,
use the original packing material.
Ship prepaid and insured by way of a traceable carrier such as
5.
United Parcel Service (UPS) or Priority Mail with delivery
confirmation to avoid loss in transit to: Cobra Factory Service,
Cobra Electronics Corporation, 6500 West Cortland Street,
Chicago, Illinois 60707 U.S.A.
6. If the product is in warranty, upon receipt of the product it will
either be repaired or exchanged depending on the model.
Please allow approximately 3 – 4 weeks before contacting Cobra
for status. If the product is out of warranty, a letter will
automatically be sent with information as to the repair charge or
replacement charge.
For any questions, please call 773-889-3087 for assistance or visit
us online at www.cobra.com.
Customer Support & Trademarks:
Customer Support
Should there be any problems with this product or further information
needed on it s features please visit www.cobra.com for support, frequently
asked ques tions, Declarations of Conformit y, and the electronic manual.
Waste Electrical and Electronic Equipment Information
This product has required the ex traction and use of natural resources for
its production. I t may contain hazardous substances that could impact
health and the environment, if not properly disposed. In order to avoid
the dissemination of those substances in our environment and to
diminish the pressure on the natural resources, we encourage you to use
the appropriate take-back systems for product disposal. T hose sys tems
will reuse or recycle most of the materials of the product you are disposing
in a sound way.
The crossed out wheeled bin symbol informs you that the product
should not be disposed of along with municipal waste and invites you
to use the appropriate separate take-back systems for product disposal.
If you need more information on the collection, reuse and recycling
systems, please contact your local or regional was te administration.
You may also contact your supplier for more information on the
environmental per formances of this product.
The product label is located on the bottom of the unit.
Trademark Statements
Cobra, JumPack and the snake design are proprietary trademarks of
Cobra Electronics Corporation, USA.
16 17
Loading...