Keep this booklet for future reference.
IMPORTANT: The remote control must not be exposed to excessive heat sources.
EN
I
Digital
Thank you for choosing a CME remote control.
The Control 5 digital remote control is ideal for replacing up to 5 remote controls for TV - SAT (satellite decoder) - TER
(Digital Terrestrial decoder) - DVD (Dvd player and Blu Ray) – PVR (Personal Video Recorder, Media Center). The remote
control has a permanent memory, so it does not lose its settings even if there are no batteries in it.
USE OF THE BUTTONS AND FUNCTIONS
The functions of the buttons described below are available only if they are on your original device.
ON/OFF switches the device OFF and
in some cases ON
Selects analogue/digital
Buttons for selecting the device to be
controlled.
TELETEXT buttons
Numeric keypad
Selects digital TV and radio
MUTE turns sound OFF and ON
Volume control +/–
For moving around within the MENU
For selecting an external
input source
Fastext functions or for selecting sub-
menus using colours
For selecting the next programme
P+ or the previous programme P–
Confi rm selection
DVD and PVR forward/back functions
6
DVD/PVR RECORD PAUSE
STOP PLAY buttons
Specifi c buttons for decoder
INSERTING THE BATTERIES
Before using the remote control, insert the batteries and programme it.
Do not leave fl at batteries inserted, as liquid may leak and damage the remote control
SETTING CODES
SETTING CODES USING INTERNET
The remote control requires 2 new 1.5V alkaline AAA/LR03 batteries. Insert them
SETTING BY MOBILE PHONE
as illustrated.
Try pressing a number button and check that the red light remains lit continuously
until you release the button. If the light fl ashes, the batteries inserted are not
charged and are about to go fl at, therefore you must substitute them.
The Control 5 digital remote control is a universal remote, so its memory contains data relating to numerous devices of
various brands available on the market.
Each original device has a specifi c code which must be used to set up the remote control.
So to use the Control 5 digital you must enter the specifi c code for each device you wish to control.
So use one of the following methods to identify the correct code and set it in your remote control:
A) - INTERNET (recommended)
B) - MOBILE PHONE (SMS)
C) - MANUAL SEARCH
If you have an Internet connection available, follow the on-line guide on the www.cme.it website to identify the specifi c
codes for the devices you wish to command. Then set the codes manually in your CME remote control as described in the
ENTERING THE CODE DIRECTLY procedure.
(this service is free; the only expense is due to sending the SMS, according to the fees applied by the mobile service carrier)
For those who do not have access to the Internet, CME now provides the opportunity to receive the codes to be set on the
remote control directly on their mobile phones.
Write an SMS including the following: 5C, Type, Brand, Model
Fixed text that must always be entered
Specify the type of device to be controlled by means of one of the
following codes: TV - STB (digital or satellite decoder) - DVD -
AUX (other audio video device).
set the brand of the device to be controlled
set the model of the device to be controlled, usually found on a
label at the back of the device (if the model is unknown, do not write
anything after the brand)
EXAMPLE:
5C, TV, PHILIPS, 32PFL3614
5C, TV, PHILIPS,
32PFL3614
7
SETTING CODES USING A MANUAL SEARCH
CHECK
Check that the other buttons correspond to the functions of the original remote control; if not, it is likely that the code
found is incorrect, but is used for a very similar device. In that case, repeat the procedure from point 2.
If the manual search for the code is successful, obtain the code in use by following the DISPLAY CODE IN USE
procedure and make a note of it inside the battery cover.
WARNING - separate data with a comma and be as precise as possible so that the information system can search for
NOTE: If no SMS is received on the mobile phone or if the message ERROR / NO CODE is displayed,
the system was not able to process the data; do not attempt to send it again and only use the MANUAL SEARCH to set the
code.
data and answer correctly.
Send the SMS to 0039 345 7518893 and wait for a reply by SMS.
After receiving the code list by SMS, set the fi rst code on the remote control as described in the ENTERING THE CODE
DIRECTLY procedure.
Stand in front of the device already turned on with the CME remote control and press the ON/OFF button
button if the device is a DVD)
. If the device does NOT turn off
(or if the DVD does not start playing)
, try to set the next code
(or the PLAY
on the SMS list on the remote control. Repeat the operation until the device responds. When the device responds, confi rm
that the other buttons are also operating correctly. If so, the remote control is ready to use. Otherwise, an inaccurate code,
used for a very similar device, is being entered; ignore the SMS list and see paragraph MANUAL SEARCH to identify a more
suitable code.
(only to be performed if the specifi c code could not be found)
1. Switch on the device to be programmed:
- if it is a TV, SAT or TER select a programme
- if it is a DVD insert a DVD.
2. Press and hold down for 6 seconds the device selection
button corresponding to the device you wish to enter the
code for.
3. Release the button. The indicator light will fl ash. Point the
remote control at the device and press the ON/OFF key
(or PLAY if it is a DVD). If the device does NOT switch off
(or if the DVD does not start playing) press the same button again slowly (it may be necessary to press the button
several times).
4. When the device responds correctly, press OK. Three
long fl ashes indicate that the operation has been carried
out correctly.
or or oror
6 SEC.
or
8
DISPLAY CODE IN USE
If they do not appear, repeat the procedure. If the result is still negative, it means the code indicated
is not included in the remote control.
ENTERING THE CODE DIRECTLY
(only to be performed if you know the specifi c code to be set)
NOTE: During the search the indicator stops fl ashing and the remote control exits the programming mode in the
following cases:
• if for 12 seconds the button indicated is not pressed or if another button is pressed
• if the list of codes to fi nd is terminated. If this happens, visit the www.cme.it website
1. Press and hold down for 6 seconds the device selection
button corresponding to the device you wish to enter the
code for.
2. Release the button. The indicator light fl ashes.
Immediately enter the specifi c code previously found.
(e.g. 1306).
3. Three long fl ashes indicate a correct setting.
If you set up the remote control using the MANUAL SEARCH
procedure, obtain and make a note of the code in use as follows:
or or oror
6 SEC.
1. Press and hold down for 6 seconds the device selection
or or oror
6 SEC.
button corresponding to the device you wish to enter the
code for.
2. Release the button. The indicator light will fl ash. Press
the TV / radio button for an instant.
3. After a pause of several seconds, the indicator light produces four sets of fl ashes, spaced out, corresponding to
the code to be obtained. Count the number of fl ashes.
Each set of fl ashes corresponds to one fi gure in the
code. Ten fl ashes correspond to the fi gure 0.
4. Make a note of the code obtained on the label on the inside of the battery cover. You may need it in future.
Code obtained = 1306
9
TROUBLESHOOTING
PROBLEM
INFO - LINE
The device does not respond and the indicator light
does not come on when a button is pressed.
SOLUTION
Check that the batteries are charged and inserted
correctly and if necessary replace them with 2 new
1,5 V AAA/LR03 alkaline type batteries.
The device does not respond but the indicator light
comes on.
Make sure that the remote control is pointing at the
device and that there are no obstacles in the way.
If necessary, enter the remote control code again by
repeating the programming procedure.
When you press a button the indicator light fl ashes
Substitute the batteries, which are about to go fl at.
and the device does not respond to commands.
The remote control does not execute all commands
correctly.
You may be using an incorrect code.
Enter the remote control settings again by repeating
the programming procedure.
If you have any queries regarding the new Control 5 digital CME remote control:
carefully read this Instructions Booklet which will allow you to solve most problems.
•
consult the www.cme.it website where you will fi nd all the answers you need quickly and easily.
•
2 year WARRANTY
The warranty is voided if the product is tampered
with or used improperly.
Remote control model Control 5 digital CME
Purchase date
The symbol showing a wheelie bin with a cross through it which appears on the device indicates that at the end of its useful life the product must be
collected separately from other waste. Therefore, at the end of the device’s life, you must take it to appropriate centres for the differentiated collection
of electrical and electronic waste, or return it to the retailer when purchasing a new device of equivalent type, on a one-for-one basis. Suitable
differentiated collection to allow subsequent recycling of the decommissioned device, with environmentally-compatible treatment and disposal, help
to prevent any negative effects on the environment and health and to promote the recycling of the materials of which the device is made. Improper
disposal of the product by the user will be subject to the sanctions in Legislative Decree No. 22/1997 (article 50 and subsequent articles of Legislative
Decree No. 22/1997).
10
Retailer stamp
Loading...