VIEW® Pro
High-definition, IP, Compressed Audio/Video Encoder, and Decoder
Quick-Start Guide
Table of Contents
THE VIEW PRO ENCODER AND DECODER ....................................1
QUICK-START OVERVIEW
MOUNTING THE ENCODER AND DECODER
THE ENCODER/DECODER IN NETWORK
CONNECTING THE ENCODER
CONNECTING THE DECODER
CONFIGURING THE ENCODER/DECODER
VIEW PRO ACCESSORY KITS
PART NUMBERS
CLEARONE CONTACTS..................................................................12
..............................................................................12
................................................................1
..................................2
......................................7
.........................................................7
.........................................................8
.....................................9
........................................................10
QUICK-START GUIDE
THE VIEW PRO ENCODER AND DECODER
The VIEW Pro E120 encoder takes digital video and audio from source
devices, such as receivers, cable boxes or DVRs, and makes the source
available anywhere on the StreamNet IP network. The VIEW Pro D110
decoder takes the combined video and audio stream, decodes it, and
then sends the video and audio to a display such as a HDTV or projector
and sound system.
IMPORTANT: The VIEW Pro E120 encoder and D110 decoder can
only be used with a StreamNet network configured using StreamNet
Dealer Setup software.
The latest version of the StreamNet Dealer Setup software can be found
on the ClearOne website at:
http://www.clearone.com/resources#enterprise_streaming
QUICK-START OVERVIEW
These steps must be done in the following order to use the VIEW Pro
encoders and decoders in your StreamNet network:
1. Mounting the Encoder/Decoder.
2. The Encoder/Decoder in Network
3. Connecting the Encoder/Decoder
4. Configuring the Encoder/Decoder.
1
VIEW PRO ENCODER/DECODER
MOUNTING THE ENCODER AND DECODER
The VIEW Pro Encoder includes rack-mount ears that attach to the
encoder to facilitate mounting in a standard rack
The VIEW Pro Decoder includes surface-mount ears that attach to
the decoder to facilitate mounting on top of a surface, under a surface,
or on a wall. It also includes mounting clips for the power supply.
Encoder with
Rack Mounting Ears
Decoder with
Surface Mounting Ears
2
QUICK-START GUIDE
The power supply for the decoder can also be mounted to a wall using
the included mounting clips.
An optional VESA Mount Bracket Kit (910-0002-006) is available for
applications where an encoder/decoder must be located on a VESA
mount. The VESA Mount Bracket Kit (910-0002-006) includes a Wall
Bracket that the can VESA Bracket can attach to.
NOTE: The VESA adapter does not attach the decoder to the back of
a monitor, but allows the decoder to be attached to a separate VESA
mount.
3
VIEW PRO ENCODER/DECODER
VESA Bracket
4
QUICK-START GUIDE
Wall Bracket
(Mount to stud or
other solid surface)
Unit with VESA Bracket
hangs on Wall Bracket
5
VIEW PRO ENCODER/DECODER
When the VIEW Pro cables cannot be concealed, cables can be surface
The metal cover
snaps onto the
wall brackets.
Edge protectors prevent
metal cover from making
contact with the cables.
Use included wire ties to
secure the cables to
the wall bracket.
Make 11 inch spacing
between top and bottom
wall bracket mounting
holes.
Mount the wall brackets
to a solid surface.
(Wall screws not included)
Two sections or more kits may be combined to make a longer raceway.
Join them using the included spring pins.
The metal cover may be cut to size as needed.
mounted using the optional 910-0002-003 VIEW Pro Cable Raceway Kit.
This raceway, in 12-inch joinable lengths, can be mounted to the wall to
secure and cover the cables to the VIEW Pro devices.
6
QUICK-START GUIDE
THE ENCODER/DECODER IN NETWORK
The VIEW Pro encoder receives input from an AV source device such as
BluRay Player, DVD Player, etc. and distributes it over a StreamNet TCP/
IP network using a standard 100 Mbit or Gbit Ethernet connection. The
decoders, as counterparts, are installed at the locations of the target
video displays. They operate together: the encoders providing the IP
data for the decoders to deliver to the displays.
CONNECTING THE ENCODER
The VIEW Pro E120 Encoder connections are from the back of the unit as
shown in the following diagram:
7
VIEW PRO ENCODER/DECODER
6 GPIO Ports
DSP forced
air intake
19 VDC
Input from
Power
Adapter
for Control
3 Inputs and
3 Outputs
2 x USB
3.0 Ports
for USB
Audio/Video
Devices
COM2 Port for
Source or 3rd-Party
Device Control
Network Port2
(Currently Not Used)
2 HDMI
Audio/Video Port
Network Port1 3.5mm
Audio Output
(Currently Not Used)
COM1 Port for
Source or 3rd-Party
Device Control
3.5mm Line-level
Audio Intput
Audio Intputs
Power
On/Off
3.5mm IR Input
for IR Learning
Left/Right
Balanced
3.5mm IR
Output for
Source
or 3rd-Party
Control
CONNECTING THE DECODER
The VIEW Pro D110 Decoder connections are from the back of the unit
as shown in the following diagram:
8
QUICK-START GUIDE
CONFIGURING THE ENCODER/DECODER
The VIEW Pro Encoder/Decoder is configured for use in the commercial
or residential network using the StreamNet Dealer Setup program.
StreamNet Dealer Setup is a PC-based program that allows you to
configure devices so that they can communicate across a StreamNet
network. Phases of the software setup include:
• Opening the existing project
• Add the new device
• Configuring the device with system-specific information regarding
Display Outputs, Controls, IP and GPIO
• Saving the project
• Sending the configuration files to the server
These steps involved in these processes are detailed in the DigiLinX
Dealer Setup manual available for viewing or download at www.
ClearOne.com.
Information specific to the VIEW Pro Encoder is contained in the VIEW
Pro - E120 Digital AV Encoder Installation and Users Manual available
for viewing or download at www.ClearOne.com.
Information specific to the VIEW Pro Decoder is contained in the VIEW
Pro - D110 Digital AV Decoder Installation and Users Manual available
for viewing or download at www.ClearOne.com.
9
VIEW PRO ENCODER/DECODER
VIEW PRO ACCESSORY KITS
The following accessory kits are available to meet the mounting and
control needs of your VIEW Pro Encoders and Decoders:
Part Number Kit Name Description
910-0002-001 VIEW Pro Rack
910-0002-002 VIEW Pro Wall
910-0002-003 VIEW Pro Cable
Mount
(Included with
Encoder)
Mount
(Included with
Decoder)
Raceway
(Optional)
Rack Mount Kit for VIEW Pro Encoder E120, Decoder
D110
• 2X - Rack Ear, Extended length
• 6X - Screw, M3 x 6mm, Pan-head, Phillips,
Thread Locking, Black
Wall Mount Kit for VIEW Pro Encoder E120, Decoder
D110
• Bracket 1Ru Rack/Wall Mount
• 2X - Screw, M3 x 6mm, Pan-head, Phillips,
Thread Locking, Black
• 2X - Bracket, 19V PSU Wall mount
Cable Raceway Kit (12 inch) for Wall Mount Kit for
VIEW Pro Decoder D110
• 1X - Extrusion, Cable Raceway Cover, 12 inch
• 2X - Bracket, Cable Raceway Wall-mount Clip
• 2X - Cable Tie (4 inch)
• 2X - Spring Pin, 5-64 inch x 1 inch
• 2X - Plastic, Edge Protector, 3 inch
10
QUICK-START GUIDE
Part Number Kit Name Description
910-0002-004 VIEW Pro IR
910-0002-005 VIEW Pro IR
910-0002-006 VIEW Pro VESA
Receiver
(Optional)
Receiver & Emitter
(Optional)
Bracket
(Optional)
IR Receiver cable for VIEW Pro Encoder E120,
Decoder D110
• 1X - IR Receiver Assembly with 6 ft. cable
IR Receiver Cable, IR Emitter Cable Kit for VIEW Pro
Encoder E120, Decoder D110
• 1X - IR Receiver with 6 ft. cable, 3.5 mm plug
• 1X - IR Emitter with 6 ft. cable, 3.5 mm plug
Wall Mount VESA Bracket Kit for VIEW Pro Encoder
E120, Decoder D110
• 1X - Bracket, VESA and Hanging Mount
• 1X - Bracket, Wall Side Mount
• 2X - Bracket, 19V PSU Wall mount
• 4X - Screw, M4 X 6mm, Pan-Head, Phillips,
Plain
11
VIEW PRO ENCODER/DECODER
PART NUMBERS
910-0000-001 VIEW Pro Encoder E120
910-0001-001 VIEW Pro Decoder D110
CLEARONE CONTACTS
HEADQUARTERS:
Salt Lake City, UT USA
5225 Wiley Post Way
Suite 500
Salt Lake City, UT 84116
Sales: 800.705.2103
Toll Free: 800.945.7730
Fax: 801.303.5711
e-mail: sales@clearone.com
EMEA:
Tel: +44 (0) 1189.036.053
e-mail: global@clearone.com
LATAM:
Tel: 801.974.3621
e-mail: global@clearone.com
TechSales
Tel: 800.705.2103
e-mail: techsales@clearone.com
Technical Support
Tel: 800.283.5936
e-mail: tech.support@clearone.com
APAC:
Tel: +852.3590.4526
e-mail: global@clearone.com
Middle East:
Tel: +852.3590.4526
e-mail: global@clearone.com
Information in this document is subject to change without notice. QSG-0010-001 Revision 1.1 October, 2014
© 2014 ClearOne, Inc. All rights reserved.
12
Loading...