ClearOne VIEW Lite EJ100 Quick Start Manual

VIEW® Lite EJ100 Digital AV Encoder

JPEG2000 Based Audio/Video Encoder

Quick-Start Guide

PRODUCT OVERVIEW .................................................................. 1

VIEW

®

LItE AV oVEr IP StrEAmIng SyStEm

........................................ 1

DEVIcE APPLIcAtIon

............................................................................ 1

ENCODERS AND DECODERS IN A NETWORK ........................... 1

PARTS INCLUDED ......................................................................... 3

MOUNTING THE EJ100 ENCODER .............................................. 3

CONNECTING THE EJ100 ENCODER .......................................... 4

CONFIGURING THE ENCODER ................................................... 6

COMPLIANCE ................................................................................ 6

PART NUMBERS ............................................................................ 7

Table of Contents

QUICK-START GUIDE

1

PRODUCT OVERVIEW

VIEW

®

LItE AV oVEr IP StrEAmIng SyStEm

The VIEW Lite platform is designed to stream high-quality audio and
video over a TCP/IP network (AVoIP™). An encoder, such as a VIEW Lite
EJ100, takes digital video and audio from a source device, such as a
receiver, cable box or DVR, and makes the source available anywhere on
the dedicated Ethernet LAN network. A decoder, such as the VIEW Lite
DJ100, takes the combined video and audio stream and decodes it. The
DJ100 then sends the video and audio to a display such as a HDTV or
projector and sound system.

DEVIcE APPLIcAtIon

The EJ100 is a high-definition, Internet Protocol, JPEG2000 based
Audio/Video encoder. The EJ100 connects to a TCP/IP network using a
Gigabit Ethernet connection. Used with the DJ100, the EJ100 encoder is
designed to be installed at the location of the target AV source.

Installation should be done by a qualified Dealer Service representative.

ENCODERS AND DECODERS IN A NETWORK

The VIEW Lite EJ100 encoder receives input from an AV source device
such as BluRay Player, DVD Player, etc. and distributes it over a
dedicated TCP/IP network using a standard Gigabit Ethernet connection.
The VIEW Lite decoder, as a counterpart, is installed at the location of the
target video display(s). They operate together; the encoders providing
the IP data for the decoders to deliver to the displays.

VIEW LITE EJ100 ENCODER

2

QUICK-START GUIDE

3

PARTS INCLUDED

The following items are included with the VIEW Lite EJ100 Encoder:

• 1X VIEW Lite EJ100 Encoder Unit

• 1X 12V DC Power Adapter

• 1X Detachable Plug

• 1X Phoenix Euroblock (Male, 3.5 mm, 3 pins)

• 1X IR Emitter (3.9 ft / 1.2 m)

• 1X IR Wideband Receiver (3.9 ft / 1.2 m, 30 kHz ~ 50 kHz)

• 2X Mounting Ears with Screws

Verify that all items have been received. If there is any issue, please
contact your ClearOne representative.

MOUNTING THE EJ100 ENCODER

The VIEW Lite EJ100 Encoder comes with mounting ears that facilitate
mounting on a table or wall.

Mounting ears shown separately

Mounting ears attached to the unit

VIEW LITE EJ100 ENCODER

4

A. LED

» Power: Solid red indicates the unit is powered on.
» Status:

• Off (no light): Unit powered off, or in the boot process.

• Blinking blue: Unit is disconnected from the EJ100 or

an active video source, or the network is down.

• Solid blue: Unit is connected to the EJ100 and a video
stream is displayed.

B. Mode Switch: Set the mode for the RS-232 function. Under

the default Normal Mode, a RS-232 connection enables serial
command control of display or 3rd-party devices. Under Debug
Mode, it enables debugging.

C. DIP Switch: Routes audio and video together with IR, and USB

signals between DJ100 and EJ100 units. To route video from
a particular source to display, toggle switches on the EJ100 to
match the positions on the chosen DJ100. To unlink a EJ100
from an DJ100, reset the EJ100 factory defaults.

NOTE: Before using the DIP switch, check that routing operations
are not performed by other tools. If they are, the switch function is

disabled. Press and hold the Reset Button to enable the switch.

CONNECTING THE EJ100 ENCODER

VIEW Lite EJ100 Front Panel

Power LED
Indicator

Status LED
Indicator

Mode
Switch

DIP
Switch

QUICK-START GUIDE

5

VIEW Lite EJ100 Rear Panel

A. 12V DC Input: Power provided by the power supply.
B. Reset Button: Press and hold for 5+ seconds for factory reset.
C. Ethernet/PoE Port: A RJ-45 10/100/1000Mbps Ethernet/PoE

port that connects to a PoE power injector, or PoE Ethernet
Network Switch for power, monitoring, and/or configuration.

• Left/Green LED: Indicates a good network connection.

• Right/Yellow LED: Blinks to indicate network activity.

D. 3.5mm Audio Input: Jack for analog audio input that replaces

the HDMI audio when plugged in.

E. 3.5mm Audio Output: Jack for analog audio output extract from

HDMI.

F. RS-232 Ports: Port for debugging and display/3rd-party device

serial command control.

G. USB Type B Port: Connectivity to a PC, MAC, or laptop for USB

HID (KVM) functionality.

H. HDMI In Port: Connectivity to an AV source device.
I. HDMI Loopback Output Port: Connectivity to an AV display

device for loopback output.

RS232 Serial
Command

3.5mm
IR Input

3.5mm
IR Output

Network/PoE
Port

3.5mm
Audio Input

12V DC Input

HDMI

Audio/

Video Input

Reset Button 3.5mm

Audio Output

USB 2.0
Port

HDMI

Audio/Video

Loopback Output

VIEW LITE EJ100 ENCODER

6

CONFIGURING THE ENCODER

The EJ100 is set up for use in an Ethernet network using the VIEW Lite
CONSOLE software, a PC-based program that allows you to configure
devices so they can communicate across an Ethernet network.

These processes are detailed in the VIEW Lite CONSOLE User Manual
available for viewing or download at www.ClearOne.com.

COMPLIANCE

Details on compliance can be found on the ClearOne website under “Resource
Library”.

J. IR Input Connector: Compatible with IR sensor (3.5mm) for

Network Passthrough.

K. IR Output Connector: Compatible with IR emitter (3.5mm) for

source display or 3rd-party control.

QUICK-START GUIDE

7

PART NUMBERS

910-0100-001 VIEW Lite Encoder EJ100
910-0100-002 VIEW Lite Decoder DJ100
910-0100-003 VIEW Lite Controller CJ100

CONTACT INFORMATION

HEADQUARTERS:

5225 Wiley Post Way
Suite 500
Salt Lake City, UT 84116

Sales:

Tel: [phone]
e-mail: [e-mail]

US & Canada:

Tel: [phone]
TollFree: 800.945.7730
Fax: [phone]

TechSales

Tel: [phone]
e-mail: [e-mail]

International:

Tel: [phone]
e-mail: [e-mail]

TechSupport

Tel: [phone]
e-mail: [e-mail]

© 2018 ClearOne, Inc. All rights reserved.

Information in this document is subject to change without notice. QSG-0058-001 Revision 1.0 JULY 2018