Page 1
Page 1 399G185 Rev A 08/03/16
Press to slide open
the battery latch
Quick
Guide
FreeSpeak II® O2 wireless beltpack
Start
A FreeSpeak II O2 wireless beltpack gives you simultaneous access to up to f ive c hannels of talk/lis ten
communication, with the ability to s witch among them a s d esired. It commun icate s with the following FS II
components:
• The Base station (FSII-BASE or FSII-BASE-II) or Eclipse HX (with E-Que-HX) that routes
communication to a nd from the beltpacks and other audio devices.
• Transceiver/Antennas (FSII-TCVR-19, FSII-TCVR-24) that provide custom coverage zones in which the
beltpacks operate.
• Antenna splitters (PD220 3 or FSII-SPL) that run up to 5 separate transceivers/antennas.
For more information about th e system, see the FreeSpeak II User Guide.
Inserting batteries
Use your thumb to s lid e open the battery latch, and insert the 3 x
AA batteries into the battery compartment ensuring the correct
alternate orientation as illustr a te d.
The batteries may be Alka line or Nickel Metal Hydride (NiMH).
To set the battery type across the system:
For FSII-BASE, within the Configuration Tool
Select System Tab > AA Battery Type
For FSII-BASE-II, within the CCM
Select Home Tab > General > Wireless > AA Battery Type
For Eclipse HX, within the EHX configuration system.
Select Configuration > Preferences > Wireless Beltpacks
Select the appropriate battery type (default is Alkaline)
Note: Selecting the incorrect battery type will not harm the
beltpack but may cause incorrec t r ea ding of battery life remain in g.
Using the Beltpack
Ensure the beltpack has charged batteries and press a nd hold the recessed power button for three seconds
to switch it on. I f you are using the beltpack with a FreeSpeak II Base station, the system has a de fault audio
set-up so the system can simply be wired an d powered before basic use. The default set-up has two partyline
(conference) audio channels (A and B). Each channel talks to:
• All the beltpacks on that channel
• The head set on the Base station.
To turn the beltpack off, press and hold the power button for three seconds.
To customize an audio channel configu r ation, please refer to the FreeSpeak II User Guide.
Page 2
Quick Start Guide | FreeSpeak II® O2 wireless beltpack (FSII BP19, FSII BP24)
Page 2 399G185 Rev A 08/03/16
LED
flashlight
LED flashlight
control
Headset
socket
3 . 5
mm stereo
jack line input
Micro USB connector
The beltpack has four keys labelled A, B, C, and
D. You can program each of these keys to
determine their communication destinations, a nd
the type of communication possibl e.
FS II Beltpack connectors
1) Connect a headset, using the XLR
connector on the b a se / rear of the
beltpack.
2) Press the appropriate key. While the key
is held down, au d io tr a nsmits on that
channel. When the key is released, audio
no longer transmits. To latch a key on
for hands-free use, quickly tap the key.
Press the key to release the latch.
3) Speak into the headset micr ophone.
4) To adjust the volu me of incoming audio
for a channel, turn the appropriate
rotary control.
5) You can configure the beltpa c k Reply key
to reply to incoming c a lls or to call a
specified destination. S ee
the
FreeSpeak II User Guide.
Entering and exiting Menu mode
Use Menu mode to:
• Configure the s e ttings for the beltpack
• Read beltpack information such as software version
• Perform a site su r vey to maximize signa l s tr e ngth and coverag e.
To enter Menu mode, press and hold the Menu key for three secon ds . To exit Menu mode, press the Menu
key again. For more information about u s ing Menu mode on the beltpack, see the FreeSpeak User Guide.
Copyright © 2016 HME Clear-Com Ltd. All rights r es erved.
Loading...