Clear-Com BP410 Quick Reference Manual

Quick Reference Guide

Belt clip

Headset

cable plug

The Beltpack Beltpack Setup

BP410

21 64 3 5

7 78 9 10

1. Battery

2. Increase Volume button (▲)

3. Decrease Volume button (▼)

4. PWR (Power) button

5. Headset cable connector

6. Battery-release latch

7. Power/Mode lights

8. Channel A (Intercom 1) button - Includes 2-wire and

4-wire connections

9. ISO (Isolate) button - To All Wireless Headsets and
Beltpacks, Base, ISO Relay and AUX OUT
(if activated)

10. Channel B (Intercom 2) button - Includes 2-wire
and 4-wire connections

Battery

RELEASE BATTERY button

¾ Insert a fully charged battery in each Beltpack with the

metal contacts inserted rst. Slide it in until it snaps.

NOTE: The battery will not slide in if inserted
incorrectly. Excessive force should not be necessary.

¾ Plug the Beltpack’s headset cable connector into each

Beltpack.

BP410 Beltpack Settings

To Set:

ISO restrict On A button

ISO restrict Off A button and ISO buttons

Handsfree On selected button(s) A button and/or B button and/or ISO and Volume up button (▲)

Handsfree Off selected button(s) A button and/or B button and/or ISO and Volume down button (▼)

Listen-Only mode On Volume down button (▼)

Listen-Only mode Off Volume up button (▲)

To Set: With the power already on...

Increase mic gain (15 steps) Press the B button while repeatedly pressing the Volume up button (▲)

Decrease mic gain (15 steps) Press the B button while repeatedly pressing the Volume down button (▼)

Increase sidetone level (5 steps) Press the A button while repeatedly pressing the Volume up button (▲)

Decrease sidetone level (5 steps) Press the A button while repeatedly pressing the Volume down button (▼)

Copyright © 2016 Clear-Com, LLC, an HM Electronics, Inc. company. All rights reserved.
Clear-Com, the Clear-Com logo and Clear-Com Concert are trademarks or registered trademarks of HM Electronics, Inc.

All functions are from an off state. Press the Power button and release with the
appropriate buttons below.

Part Number: 399G214 Rev A
Date: 12/5/16

General Use

Beltpack Sidetone Adjustment:

¾ Press and hold the A button while you repeatedly press up (▲) to increase or press down (▼) to decrease

audio levels.

Changing the battery:

¾ When a Beltpack battery becomes weak, a headset voice prompt will say “Change battery.”

¾ Press the RELEASE BATTERY button on the belt clip of the pouch, and use your thumb to slide the battery

from the belt-pac.

¾ When charging the battery using the AC50 Battery Charger, the charging time is about 2.5 hours.

The DX410 Console

Beltpack

Registration

Power Switch

STATUS AUTO NULLREG

Audio Channel and

Auto-Null Controls

Local Headset

Controls

Register Beltpack

¾ Make certain the Beltpack is turned Off.

¾ Press REG button on base station.

– STATUS display on the base station shows “o” for registration mode.

¾ On the Beltpack, press and hold ISO while pressing POWER and then release all buttons.

– The power lights blink red, then green and then turn off. One power light remains green.
– The registration number will appear on the base station STATUS display.

AUTO NULL Adjustment (only if using 2-wire interface)

If echo is heard in wireless Beltpacks on A or B:

¾ Use pointed object (e.g. pen) to press and hold the A or B AUTO NULL button for 2 seconds.

CAUTION: Before pressing an AUTO NULL button, be certain there are no open microphones on the wired

system. Notify wired system users that a loud noise may occur in their headsets during the auto null adjustment.

The system may be out of operation for approximately 50 seconds during this adjustment.

Local Headset Communication

¾ SEL button selects communication with A, B or ISO.

– A, B or ISO lights indicate selection.

¾ TALK button

– Press and release quickly to “latch on” for open communication.

– Press and hold while talking for momentary communication – release when nished.

¾ VOLUME control adjusts the audio level in local headset ear piece.

¾ MIC LEVEL control adjusts the audio level going out from local headset microphone.

Technical Support

In The Americas and Asia – Tel: [phone] or 1.800.462.4357 Menu option 1 • Hours: 8:00am-5:00pm Pacic Time • Web: www.clearcom.com

In Europe, Middle East and Africa – Tel: [phone] • Hours: 8:00am-5:00pm GMT • Email: [e-mail]