Claypaky TW C71055, F21230, W C71060 Instruction Manual

1

INSTRUCTIONS MANUAL

Congratulations on choosing a Clay Paky product!
We thank you for your choice. Please note that this product,
as all the others in the rich Clay Paky range, has been
designed and manufactured with total quality to ensure
excellent performance and best meet your expectations and
requirements.

Carefully read this instruction manual in its entirety and keep it
safe for future reference.
It is essential to know the information and comply with the
instructions given in this manual in order to ensure the fitting is
installed, used and serviced correctly and safely.
CLAY PAKY S.p.A. disclaims all liability for damage to the
fitting or to the other property or persons deriving from
installation, use and maintenance that have not been carried
out in conformity with this instructions manual, which must
always accompany the fitting.
CLAY PAKY S.p.A. reserves the right to modify the
characteristics stated in this instructions manual at any time and
without prior notice.

CONTENTS

Page

2
3
3
4

7
13
13
14
15
16
16
17

PRELIMINARY

Contents

Safety information
Unpacking and preparation
Installation and start-up
Control panel
Main menu
Manual zoom
Maintenance
Battery removal
Optional accessories
Technical data
Cause and solution of problems
Channel functions

GLOW UP

& FLIGHT CASE

C C71050
TW C71055
W C71060

F21230

ENGLISH

2

GLOW UP

• Installation

Make sure all parts for fixing the projector are in a good state of repair. Make sure the point of
a

nchorage is stable before positioning the projector.
The safety chain must be properly hooked onto the fitting and secured to the framework, so that,
if the primary support system fails, the fitting falls as little as possible. If the safety chain gets used,
it needs to be replaced with a genuine spare.

• Minimum distance of illuminated objects

The projector needs to be positioned so that the objects hit by the beam of light are at least 0.2
metres (8’ 2”) from the lens of the projector.

• Minimum distance from flammable materials

The projector must be positioned so that any flammable materials are at least 0.20 metres (8") from
e

very point on the surface of the fitting.

• Mounting surfaces

It is permissible to mount the fitting on normally flammable surfaces.

• Maximum ambient temperature

Do not use the project if ambient temperature (Ta) exceeds 40°C.

• IP65 protection rating

The equipment is fully protected against dust (first digit 6) and against jets of water (second digit 5).

• Protection against electrical shock

Connection must be made to a power supply system fitted with efficient earthing (Class I appliance
according to standard EN 60598-1).
It is, moreover, recommended to protect the supply lines of the projectors from indirect contact
and/or shorting to earth by using appropriately sized residual current devices.

• Connection to the power mains

A qualified electrician must perform connection to the power mains.
Check that the mains frequency and voltage correspond to the frequency and voltage for which the
projector was designed and indicated on the electrical data label.
This label also gives the input power. Refer to the latter to evaluate the maximum number of
devices to be connected to the mains to avoid overloads.

• External surface temperature

The maximum temperature that can be reached on the external surface of the fitting, in a thermally
steady state, is 90°C (320°F).

• Maintenance

Before starting any maintenance work or cleaning the projector, cut off power from the supply
mains. After switching off, do not remove any parts of the fitting for at least 10 minutes. The lenses
must be mounted and, if visibly damaged, they have to be replaced with genuine spares.

• Battery

This product contains a lithium iron tetraphosphate rechargeable battery. To protect the
environment, please discard the battery at the end of its life cycle according to current law.
Instructions on how to remove the battery from the equipment are available at www.claypaky.it.

S

AFETY INFORMATION GLOW UP

The products referred to in this manual conform to the European Community Directives to which
they are subject:

• Low Voltage Directive 2006/95/EC

• Electromagnetic Compatibility Directive 2004/108/EC

0.2

90°C

IP65

LiFePo

3

GLOW UP

<Nessuno(a)>

• Installation

Ensure that the Flight Case, when used for charging Glow UP, is positioned at a distance of 15
c

m from any surface or wall, to allow proper ventilation.

• Maximum ambient temperature

Do not operate the device if ambient temperature (Ta) exceeds 40°C.

• IP20 protection rating

The fitting is protected against penetration by solid bodies of over 12mm (0.47”) in diameter (first
digit 2), but not against dripping water, rain, splashes or jets of water (second digit 0).

•

Protection against electrical shock

C

onnection must be made to a power supply system fitted with efficient earthing (Class I appliance
according to standard EN 60598-1).
It is, moreover, recommended to protect the supply lines of the projectors from indirect contact
and/or shorting to earth by using appropriately sized residual current devices.

• Connection to the power mains

A qualified electrician must perform connection to the power mains.
Check that the mains frequency and voltage correspond to the frequency and voltage for which the
projector was designed and indicated on the electrical data label.
This label also gives the input power. Refer to the latter to evaluate the maximum number of
devices to be connected to the mains to avoid overloads.

• Maintenance

Before starting any maintenance work or cleaning, cut off power from the supply mains.

S

AFETY INFORMATION FLIGHT CASE

The products referred to in this manual conform to the European Community Directives to which
they are subject:

• Low Voltage Directive 2006/95/EC

• Electromagnetic Compatibility Directive 2004/108/EC

IP20

4

GLOW UP

U

NPACKING AND PREPARATION

P

acking content - Fig. 1

2

Projector installation - Fig. 2
The projector can be installed on the floor resting on specific rubber feet, on a truss, on the ceiling or wall.

WARNING: the safety chain must be installed except when the projector rests on the floor. (Code 105015/801 available upon request). This
must be secured to the projector support structure and then hooked to the fastening point at the centre of the base.

1

2

3

2

3

1

4

3

Connecting and disconnecting the power cord - Fig. 3
When connecting the power cord the user can choose whether to use the GlowUp in one of the following ways:

1) Power cord connected for battery charge.

2) Power cord connected for projector power (thus bypassing battery operations).
The GlowUp cannot work in both ways simultaneously.

INSTALLATION AND START-UP

099114

OPTIONAL ACCESSORY C71110

1

5

GLOW UP

Switching on the projector - Fig. 6
The projector immediately turns on when the power cord is plugged in or, if used in battery mode, by pressing and holding down keys

A

and Sfor

several seconds.

Clay Paky GLOW UP Address xxx BAT xx%
GLOW UP Software release x.x x xxxxx ??? *

The control panel (Figure 8) has a display and buttons for complete programming and management of the projector menu.
The display can be in one of two conditions: idle status and settings status.
When idle, the projector DMX address and percent battery charge are displayed.
If no button is pressed after a wait period (about 60 seconds) when in menu settings status, the display automatically returns to idle status. It should
be noted that when this condition occurs, any modified value that has not yet been confirmed with the

A

key will be cancelled.

To turn off the GlowUP, hold down keys

A

and Sfor several seconds. A confirmation message will appear (Switch off?).

Press

A

-Yes to turn off the GlowUP or press S-NO to return to the settings menu.

C

ONTROL PANEL

6

Connections to the power mains - Fig. 4

L
N

D

MX

512

Power Supply

4

5

SIGNAL

S

CREEN

DMX 512

5 PIN

1

2

3

4

5

S

IGNAL

SCREEN

1

3

2

DMX 512

3 PIN

SIGNAL

SIGNAL

Connections to the control signal line (DMX) - Fig. 5
Use a cable conforming to specifications EIA RS-485: 2-pole twisted, shielded, 120Ω characteristic impedance, 22-24 AWG, low capacity. Do not use
microphone cable or other cable with characteristics differing from those specified. End connections must be made using XLR type 3 or 5-pin male/female
connectors. A terminating plug must be inserted on the last projector with a resistance of 120 Ω (minimum 1/4 W) between terminals 2 and 3.
IMPORTANT: The wires must not make contact with each other or with the metal casing of the connectors. The casing must be connected to the shield
braid and pin 1 of the connectors.

* see pag. 5

Display symbology

6

GLOW UP

Continued

➔

Initial projector address settings

An initial address must be set on each single project for the control signal.
Address settings: see page 9.

DMX Address

ADDR 001 BAT 40%

DMX C

Yy

W

Time or percent remaining
of the battery charge

Operating mode

(

see page 15)

Link status

(Wireless or Wired)

Errors / Warning

Button functions – Menu SET

• If pressed in idle status: Cyclically switches between idle status and menu settings.

• If pressed while setting a menu: Moves to an upper level without changing anything (exits the function)

Decreases the value displayed (with auto-repetitions), or passes to the next item on the menu
For quick access to the minimum parameter value, press the UP key while holding down the DOWN key.

Increases the value displayed (with auto-repetitions), or passes to the previous item on the menu
For quick access to the maximum parameter value, press the DOWN key while holding down the UP key.

Confirms the displayed value or activates the displayed function or opens the next menu.

SELECT

DOWN

UP

ENTER

Con Il GlowUp in condizione di riposo, il display visuallizza la pagina delle informazioni:

Transmission to DMX cable

Reception from DMX cable

Reception DMX from Radio (wireless)

Transmission DMX from Radio (wireless)

Display symbology- (Stato del Link)

GLOW UP

7

4

3

1

2

1

2

Fuse 6,3x32mm

10AT 250Vac

(030470)

Fuse 6,3x32mm

3AT 250Vac

(030471)

9

8

Charging glow up - Fig. 8
From 1 to 6 Glow Ups can be simultaneously charged by appropriately connecting and powering the flight-case.

Replacing flight case fuses - Fig. 9
Each flight-case has 2 fuses associated with the main power cord connection and one fuse for each Glow UP charge station.

8

GLOW UP

MAIN MENU

M

ENU SET

Continued

➔

P

rogram

1

E

dit scene

E

dit

S

equence

DMX

r

ecorder

Advanced

5

FW

Uploader

Setup Model

CPU Reset

Test

Radio Setup

Charge

Battery hours

Discharge

Battery hours

LED

temperature

Total LED

hours

23

M

anual

Control

Green Channel 2

Stop

Strobe

Dimmer

Stop

S

trobe

P

reset

Colors

R

ed

C

hannel 1

D

immer

C TW W

B

lue

Stop

S

trobe

W

hite

4

Charge

DMX

Monitor

System
version

Charge

Left

Charge

Hours

Information

Radio

F

ixture ID

Display

Contrast

B

attery

Display

F

actory

D

MX

Address

M

ode

Color

temperature

(TW only)

S

etup

9

GLOW UP

Shortcut keys menu:

By pressing the ENTER

A

key and UP B, the DMX address setting function can be quickly accessed.

By pressing the ENTER

A

key and DOWN C, it is possible to assign the desired command to the GlowUp Radio module:

1) Use the UP

B

and DOWN Ckeys to select one of the following settings:

U

nlink Transmitter – Disconnected from the transmitter
Link Receivers – Connected to all free receivers
Unlink Receiver – Disconnected from all receivers

2) Press ENTER

A

to confirm the selection (the display blinks for several seconds) or SELECT Sto keep the current settings and return to the

previous Menu.

By pressing any button when Glow Up is in idle status, the BUTTON FUNCTION menu is accessed.

Press SELECT

S

SET to access the menus (vedi pag. 10):

Program
Setup
Manual Control
Information
Advanced

(L'accesso al Menu ADVANCED è consigliato a personale tecnico qualificato)

Press ENTER AMOD to select the Glow UP operating mode

Use the UP

B

e DOWN Ckeys to select the mode from those available:

Stand Alone / DMX – Press ENTER

A

to confirm (runs “Unlink Transmitter”, receives the DMX at the pre-set address; by using the PLAY  key, a scene

may be chosen to be run locally and the DMX being inactive)

Master/Slave (The "Transmitter" transmits to the "Receivers" the default programme in PLAY) - Press ENTER

A

and select the mode from those available:

• Receiver enables established wired or wireless reception and reads channels, starting from channel DMX 1, without changing the pre-set DMX address.

• Transmitter enables established wired or wireless transmission, transmits starting from channel DMX 1, without changing the pre-set DMX address.

Master/Slave DMX Rec (The "Transmitter" transmits the DMX recording to the "Receivers") - Press ENTER E and select the mode from those available:

• Receiver enables established wired or wireless reception and reads channels, starting from the pre-set DMX address.

• Transmitter enables established wired or wireless transmission, transmits starting from the pre-set DMX address.

NOTE: in a GlowUp series which is part of a battery, it is imperative to first select all the receivers and finally select the Transmitter.



II

UP BPLAY/PAUSE key: activates or pauses a particular mode.

By pressing the UP

B

PLAY  button, the sub-menu can be accessed:

Fixed Colours: it is possible to associate a bit value to each GlowUp channel or you can select a color from the stored ones by accessing the Preset Colors
menu (see table on page 9).

È possibile miscelare Strobo e Dimmer con qualsiasi canale colore impostato

Sequence: it is possible to associate Speed and Fade of the pre-set Sequences (Preset 1,2,3)



DOWN CSTOP key: deactivates the active programme.

Symbol SET  or

II 

MOD

Function Setting Play/Pause Stop Mode

BAT 40

%

??

SET

MOD

Stand Alone / DMX

Master / Slave

Master / Slave DMX Rec

M

ode

Fixed Colours

Sequernces

Play 

10

GLOW UP

PRESET COLORS for Stand Alone “GlowUp C”

Colour Reference

Bit value

RGBW

01 RED - 255 000
02 GREEN -0255 00
03 BLUE -00255 0
04 YELLOW - 255 255 00
05 CYAN -0250 185 0
06 MAGENTA - 255 0 140 0
07 WHITE -000100
08 ORANGE - 255 115 00
09 PINK - 127 00100
10 VIOLET - 255 0 184 200
11 AQUA - 85 255 105 0
12 SKY BLUE - 118 255 150 0
13 FULL WHITE - 255 255 255 255
14 COOL WHITE - 225 255 253 255
15 WARM WHITE - 255 255 220 255
16 WHITE 3200 - 255 176 0 255
17 WHITE 2500 - 255 99 0 255
18 YELLOW LEE 101 133 145 00
19 STRAW LEE 103 255 255 0 240
20 ORANGE LEE 105 246 195 00
21 LIGHT ROSE LEE 107 218 00255
22 DARK PINK LEE 111 255 0 120 255
23 MAGENTA LEE 113 255 0 78 0
24 BLUE LEE 115 0 255 175 0
25 MED BLUE GREEN LEE 116 0 255 160 0
26 DARK BLUE LEE 119 0 180 180 0
27 BRIGHT PINK LEE 128 255 0 141 95
28 MEDIUM BLUE LEE 132 0 255 200 0
29 GOLDEN AMBER LEE 134 255 175 0 25
30 DEEP GOLDEN AMBER LEE 135 255 140 0 25
31 PALE LAVENDER LEE 136 00100 190
32 APRICOT LEE 147 152 122 0 76
33 DARK LAVENDER LEE 180 0 114 144 112
34 CHOCOLATE LEE 156 238 189 0 227
35 JUST BLUE LEE 079 0 187 175 0
36 SURPRISE PINK LEE 194 78 00255
37 SCARLET LEE 024 255 0 58 113
38 SURPRISE PEACH LEE 017 145 00153
39 FIRE LEE 019 255 141 44 0
40 ENGLISH ROSE LEE 108 161 119 0 255
41 MAUVE LEE 126 255 0 208 150
42 BRIGHT BLUE LEE 141 0 255 186 37
43 ALICE BLUE ROSCO 378 0 255 223 140
44 ROSE INDIGO ROSCO 358 00255 133
45 URBAN BLUE ROSCO 081 0 255 187 35
46 COOL BLUE ROSCO 066 0 255 148 153
47 LIGHT SALMON ROSCO 030 255 112 0 162
48 MAYAN SUN ROSCO 318 150 114 0 162
49 CHERRY ROSE ROSCO 332 255 0 92 0
50 FLESH PINK ROSCO 034 255 0 132 255
51

SKELTON EXOTIC SANGRIA

ROSCO 039 255 0 180 100

11

GLOW UP

EDIT SCENE

To create/overwrite/modify a SCENE customised by the user:
1

) Press ENTER

A

–

SCENE 1 appears on the display.

2) Use the UP

B

and DOWN Ckeys to select from the ten available

SCENES.

3) Press ENTER

A

to open a SCENE.

4) A value can be associated with each GlowUp channel inside each
SCENE using the UP

B

and DOWN Ckeys.

5) When finished with settings, press SELECT

S

. A confirmation

message appears: SAVE SCENE X ?.

6) Press ENTER

A

to confirm and save the SCENE or SELECT Sto

r

eturn to the previous menu.

EDIT SEQUENCE

Allows you to create a sequence, made up of a series of SCENES saved
by the user.

1) Press ENTER

A

– MEMORY 1 appears on the display.

2) Use the UP

B

and DOWN Ckeys to select the STEP to be

attributed a SCENE.

3) Press ENTER

A

, and use the UP Band DOWN Ckeys to select

the SCENE to be set (SC0...or NONE).

4) Press ENTER

A

to confirm the selection or SELECT Sto return to

the previous Menu.

DMX RECORDER

To record a scene sequence programmed on the unit.

Il proiettore per
accettare una registrazione deve essere settato in Slave --> Receiver.
Premere ENTER

A

e azzerare la "Memory" premendo nuovamente

ENTER

A

. A questo punto il GlowUp è pronto a memorizzare dati
DMX da centralina (DMX waiting ...).
Una volta effettuata la registrazione premere ENTER

A

per

memorizzare, in caso contrario premere SELECT

S

Esc.

DMX ADDRESS

Allows the user to set the DMX address to be assigned to the projector.

1) Press ENTER

A

– the current DMX address appears on the display.

2) Use the UP

B

and DOWN Ckeys to set the DMX address.

3) Press ENTER

A

to confirm the selection (the display blinks for

several seconds) or SELECT

S

to keep the current settings and

return to the previous Menu.

RADIO

Assigns the desired command to the GlowUP Radio module Radio.

1) Press ENTER

A

– current settings appear on the display.

2) Use the UP

B

and DOWN Ckeys to select one of the following

settings:

Unlink Trasmitter – Disconnected from the transmitter
Link Receivers – Connected to all free receivers
Unlink Receiver – Disconnected from all receivers

3) Press ENTER

A

to confirm the selection (the display blinks for

several seconds) or SELECT

S

to keep the current settings and

return to the previous Menu.

MODE

Assigns the desired command to the GlowUP Radio module

1) Press ENTER

A

– current settings appear on the display.

2) Use the UP

B

and DOWN Ckeys to select one of the following

settings:

• SLAVE PRIORITY: GlowUp runs as a Slave

Press ENTER

A

and use the UP Band DOWN Ckeys to select

la priorità in ricezione del segnale DMX, in caso di conflitto tra segnale
via cavo o wireless

• Cable (default)

• Wireless

PROGRAM MENU

SET UP MENU

Program Edit scene

E

dit

Sequence

DMX

recorder

Setup

Radio

DMX

Address

Mode

12

GLOW UP

Press ENTER Ato confirm the selection (the display blinks for
several seconds) or SELECT

S

to keep the current settings and

return to the previous Menu.

• MASTER OUTPUT: GlowUp runs as a Master

Press ENTER

A

and use the UP Band DOWN Ckeys to select

come si desidera che venga trasmesso il segnale DMX ad altri
apperecchi:

C

able+Wireless
Cable
Wireless

Press ENTER

A

to confirm the selection (the display blinks for

several seconds) or SELECT

S

to keep the current settings and

return to the previous Menu.

• REPEATER: GlowUp runs as a repeater

P

ress ENTER

A

a

nd use the UP

B

a

nd DOWN

C

k

eys to select

how to run GlowUP as a repeater: :
Direction – Press ENTER

A

again and use the UP Band DOWN

C

keys to select whether the repeater should transmit the DMX signal from:

-Wireless to Cable

-Cable to Wireless

Press ENTER

A

to confirm the selection (the display blinks for

several seconds) or SELECT

S

to keep the current settings and

return to the previous Menu.

Function– Press ENTER

A

again and use the UP Band DOWN

C

keys to select whether the repeater should run from:

- Repeat & Play (Il GlowUp ripete ed esegue)

- Repeat Only (Il GlowUp funziona solo come ripetitore)

Press ENTER Ato confirm the selection (the display blinks for
several seconds) or SELECT

S

to keep the current settings and

return to the previous Menu.

Enable/Disable

Press ENTER

A

to confirm the selection (the display blinks for

several seconds) or SELECT

S

to keep the current settings and

return to the previous Menu.

COLOR TEMP (GLOWUP TW)

Allows the user to select the color mixing system.

1) Press ENTER

A

– current settings appear on the display.

2) Use the UP

B

and DOWN Ckeys to select Independent mode or

Constant intensity mode or Max intensity mode.

3) Press ENTER

A

to confirm the selection (the display blinks for

several seconds) or SELECT

S

to keep the current settings and

return to the previous Menu.

FIXTURE ID

Allows you to display the GlowUP ID address.

1) Press ENTER

A

– the ID address appears on the display.

DISPLAY

Allows you to dim the display backlight 60 seconds after switching to idle
status. To turn it back on, simply press any key.

1) Press ENTER

A

– current settings appear on the display.

2) Use the UP

B

and DOWN Ckeys to turn display backlight OFF or ON.

3) Press ENTER

A

to confirm the selection (the display blinks for

several seconds) or SELECT

S

to keep the current settings and

return to the previous Menu.

CONTRAST

Lets the user modify display contrast.

1) Press ENTER

A

– current settings appear on the display.

2) Use the UP

B

and DOWN Ckeys to modify the value from 0 to 10

according to the desired contrast.

3) Press SELECT

S

to return to the previous Menu.

Continued

➔

Color

temperature

(TW only)

Display

Fixture ID

Contrast

GLOW UP

BATTERY DISPLAY

Allows you to select how to display the battery charge in idle status.

1) Press ENTER

A

– current settings appear on the display.

2) Use the UP

B

and DOWN Ckeys to select one of the 3 following

options:
Automatic: displays the remaining battery charge in hours or as a
percentage.

Percentage: displays the percentage of remaining battery charge.
T

ime left: displays the remaining time of the battery charge in hours.

3) Press ENTER

A

to confirm the selection (the display blinks for

several seconds) or SELECT

S

to keep the current settings and

return to the previous Menu.

FACTORY

Used for restoring default values on all options menu items and relevant
submenus.

1) Press ENTER

A

– a confirmation message appears on the display (Ok?)

2

) Press ENTER

A

t

o confirm the selection (the display blinks for

several seconds) or SELECT

S

to keep the current settings.

Allows the user to set a level for each of the following channels in BIT from
the control panel:

GLOWUP C GLOWUP TW GLOWUP W
Red Tunable white Dimmer
Green Dimmer Stop Strobe
Blue Stop Strobe
White
Dimmer
Strop Strobe
Macro Color
Macro Timing
Macro Fading

1) Press ENTER

A

– the first channel (RED) appears on the display.

2) Use the UP

B

and DOWN Ckeys to select the concerned channel.

3) Press ENTER

A

and use the UP Band DOWN Ckeys to assign

the DMX level to the selected channel (value between 0 and 255).

4) Press SELECT

S

to return to the previous Menu.

SYSTEM VERSION

Displays the version of the firmware loaded on the CPU board.

1) Press ENTER

A

– two options appear on the display:

Application release

Boot release (Software di sicurezza)

2) Use the UP Band DOWN Ckeys to select which of the two
firmware version items to be displayed.

3) Press ENTER

A

– the release appears on the display.

4) Press SELECT

S

to return to the previous Menu.

CHARGE %

Allows you to display the percentage of remaining battery charge.

1) Press ENTER

A

to display the percentage.

2) Press SELECT

S

to return to the previous Menu.

CHARGE LEFT

Allows you to display the remaining time of battery charge.

3) Press ENTER

A

to display the remaining hours.

4) Press SELECT

S

to return to the previous Menu.

INFORMATION MENU

13

Battery

D

isplay

Factory

M

anual

Control

Green

Dimmer

Stop

Strobe

Preset
Colors

Red

Blue

White

C TW W

Channel 2

Stop

Strobe

Channel 1 Dimmer

Stop

Strobe

Charge

System
version

Charge

Left

Information

MANUAL CONTROL MENU

14

GLOW UP

CHARGE HOURS

Permette di selezionare come visualizzare la carica della batteria sul
display in stato di riposo.

5) Premere ENTERAper visualizzare le ore di carica della batteria.
6

) Premere SELECT

S

p

er tornare al Menu precedente.

DMX MONITOR

Displays the DMX input level in bit for each GlowUP channel.

1) Press ENTER

A

– the first channel appears on the display.

2) Use the

B

and DOWN Ckeys to select the channel.

3) Press ENTER

A

to display the channel DMX level (value between 0

and 255).

4) Press SELECT

S

to return to the previous Menu.

FW UPLOADER

Used to transfer software from one projector to all other connected
projectors.

1) Press ENTER

A

use the UP() e DOWN() keys to select:

Cable upload: to start the firmware upload via DMX cable.
Radio upload: to start the firmware upload via wireless

2) Press ENTER

A

to transfer firmware or SELECTSto return to the

previous Menu.

SETUP MODEL

Use to change/select the model to be assigned to the projector.

1) Press ENTER

A

– current settings appear on the display.

2) Use the

B

and DOWN Ckeys to select one of the following
models:
COLOR
TUNABLE WHITE
WHITE

3) Press ENTER

A

to confirm the selection (the display blinks for

several seconds) or SELECT

S

to keep the current settings and

return to the previous Menu.

CPU RESET

Used to reset the CPU. Settings will not be reset.

1) Press ENTER

A

– a confirmation message appears on the display

(OK?)

2) Press ENTER

A

to RESET or SELECTSto return to the previous

Menu.

TEST

Used to test the correct operations of effects.

1) Press ENTER

A

.

2) Use the

B

and DOWN Ckeys to select the Test function.

3) Press ENTER

A

to confirm the select and start the TEST or SELECT

S

to keep current settings.

RADIO SETUP

Permette di settare il modo di Trasmissione Radio tra i 2 disponibili.

1) Premere ENTER

A

, ed entrare nel sottomenu 'TX mode' premendo

nuovamente ENTER

A

.

2) Con i tasti UP

B

e DOWN Cselezionare:
G3 - DMX (portata maggiore) oppure
G4 - DMX + RDM (portata inferiore).

3) Premere ENTER

A

per confermare oppure SELECTSper

mantenere l'impostazione corrente.

L'accesso al sottomenu 'RDM discovery' viene fatto nel caso di sostituzione
della scheda Radio a seguito di un'anomalia della stessa, serve per attivare
la comunicazione tra la scheda Radio e la CPU del GlowUp.

Continued

➔

ADVANCED MENU

A

dvanced

FW

Uploader

D

MX

Monitor

C

harge

Hours

Setup Model

CPU Reset

Test

Radio Setup

15

GLOW UP

Premere ENTERAper attivare la ricerca (wait .....) in caso di risultato

positivo apparirà sul display la scritta OK.

CHARGE BATTERY HOURS

Permette di visualizzare le ore totali di carica della batteria dalla
c

ostruzione ad oggi.

1) Press ENTERA– total charge hours appear on the display.

2) Press SELECT

S

to return to the previous Menu.

DISCHARGE BATTERY HOURS

Displays total GlowUp battery powered operating hours from last time
used,

dalla costruzione ad oggi.

1) Press ENTERA– total battery powered operating hours appear on
the display.

2

) Press SELECT

S

t

o return to the previous Menu.

LED TEMPERATURE

Displays the LED working temperature.

1) Press ENTER

A

– two options appear on the display:

Temperature (real-time LED temperature)
Max Temperature (maximum temperature measured on LEDs)

2) Use the UP

B

and DOWN Ckeys to select which of the two

temperature items to be displayed.

3) Press ENTER

A

to display or SELECTSto return to the previous

menu.

To reset the “Max Temperature” value, simultaneously press and hold
down the UP

B

and DOWN Ckeys for several seconds. When “Rst?”

(Reset) appears, confirm by pressing ENTER

A

.

TOTAL LED HOURS

Displays total LED working hours

, dalla costruzione ad oggi.

1) Press ENTERA– total LED working hours appear on the display.

2) Press SELECT

S

to return to the previous Menu.

L

ED

temperature

T

otal LED

hours

D

ischarge

Battery hours

C

harge

Battery hours

16

GLOW UP

Modalità Slave Priority Repeater Master Output

Testo Visualizzato

sul display

S

tand Alone / DMX in play/pause - Off - PLAY (o PAUSE)

- Wireless to Cable + Repeat &Play - PLAYW→C (o PAUSW→C)

- Cable to Wireless + Repeat & Play - PLAYC→W (o PAUSC→W)

- Wireless to Cable + Repeater only -W→C

- Cable to Wireless + Repeater only -C→W

Stand Alone / DMX in stop Cable Off - DMX C

Wireless Off - DMX W

- Wireless to Cable + Repeat &Play - DMXW→C

-

Cable to Wireless + Repeat &Play - DMXC→W

- Wireless to Cable + Repeater only -W→C

- Cable to Wireless + Repeater only -C→W

Master Slave Tx (master addr 1) --Cable MAST C

--Wireless MAST W

--Cable+Wireless MAST CW
Master Slave Rx (slave addr 1) Cable Off - SLV C

(non va in play) Wireless Off - SLV W

- Wireless to Cable + Repeat &Play - SLV W→C

- Cable to Wireless + Repeat &Play - SLV C→W

- Wireless to Cable + Repeater only -W→C

- Cable to Wireless + Repeater only -C→W
DMX Memory Tx (master all addr) --Cable MMTX C

--Wireless MMTX W

--Cable+Wireless MMTX CW
DMX Memory Rx (slave addr N) Cable Off - MMRX C

(non va in play) Wireless Off - MMRX W

- Wireless to Cable + Repeat &Play - MMRX W→C

- Cable to Wireless + Repeat &Play - MMRX C→W

- Wireless to Cable + Repeater only -W→C

- Cable to Wireless + Repeater only -C→W

Manual zoom - Fig. 10
The GlowUP has a manual zoom located on the back of the projector head.

M

ANUAL ZOOM

17

GLOW UP

1

1/4 Turn

2

11

MAINTENANCE

1

2

10

Antenna

Aerial

18

GLOW UP

3

4

6

5

1/4 Turn

2

1

12

B

ATTERY REMOVAL

This product contains lithium iron tetraphosphate rechargeable battery. To protect the environment, please discard the battery at the end
of its working life according to current law.

LiFePo

Periodic cleaning - Fig. 13
To ensure optimal operation and performance for a long time it is essential to periodically clean the parts subject to dust and grease deposits. The fre­quency with which the following operations are to be carried out depends on various factors such as wear and the work environment quality (air humi­dity, dust, salinity, etc.). To remove dirt from external parts, use a soft cloth dampened with any liquid glass cleaning detergent.
It is recommended that the projector undergoes an annual service by a qualified technician for special maintenance involving at least the following
operations:

• General cleaning of internal parts.

• General visual check of internal parts, cabling, mechanical parts, etc.

• Electrical, photometric and functional checks; eventual repairs.

13

Parts requiring frequent cleaning.

19

GLOW UP

1

2

14 15

OPTIONAL ACCESSORIES

MAGNETIC HOLDER
255036/001 black
255036/002 white

PADLOCK
Not commercialized from Clay Paky

20

GLOW UP

365,5

(

14,37")

226

(8,90")

165

(6,49")

T

ECHNICAL DATA

THE PROJECTOR WILL NOT SWITCH ON

TROUBLE

THE PROJECTOR WILL NOT SWITCH ON

DEFECTIVE PROJECTION

REDUCED LUMINOSITY

POSSIBLE CAUSES

CHECKS AND REMEDIES

No power supply.
LED burnt out or defective.
Signal transmission cable faulty or disconnected.
Incorrect addressing.
Fault in the electronic circuits.
Optic fault.
Dust or grease deposits.

Check the power supply voltage or battery charge.
Replace LED.
Replace the cables.
Check addresses (see instructions).
Call an authorised technician.
Call an authorised technician.
Clean (see instructions).

CAUSE AND SOLUTION OF PROBLEMS

Source

4 10 W MC-E Cree leds

Led pilot power

40W

Optics

Optic zoom, manually adjustable, magnetic support
for any additional diffusers

L

ED color temperature

5700°C GlowUP C
6000°C GlowUP W
6200°C cool white GlowUp TW
2700°C warm white GlowUp TW
4200°C cool+warm white GlowUp TW

Head adjustment

+

/-105°

Cooling

High efficiency external die-cast aluminium

Control

• Wireless DMX multimode: Master, Slave and
Reapeter

• Antenna built in the case IP65

• Master: can transmit other slaves the synchroni­sed DMX scenes saved on it, both as macros
and as DMX recorder.

• Repeater: Receives the signal from the master
and re-transmits it to other Slaves hidden from
the master

• XLR 5-pole DMX-in DMX-out standard sockets

• Remote wireless board settings with PC

• Default macros, user programmable macros.

• DMX recorder to save scene sequences.

User interface

• LCD display 2 lines with 16 characters each,

backlit LED, white on black

• 4 membrane buttons

External power

full range 100-240V 50-60Hz, PowerCon connec­tor, for both battery charge and normal operations

Absorbed power

50W max - 170 VA

Body

• Injection pressed ABS case (UV protected)

• Finish: Polished metallic – Painted White or
Black

• carrier handle

• 4 non-slip rubber feet

F

ittings

2 fast-look holes for omega hook-up

Safety

safety chain hole and padlock hole

Weight

7.5 Kg

Protection rating

IP65

Valves

Compensation valve IP65

Battery

• Duration 10 hours full, white, 20 hours color fade

• 4-hour fast charge from flight case, 8 hours in
slow charge with PowerCon

• More than 2,000 charge/deplete cycles

• No memory effect

• No acid leaks

Working position

Works in any position

CE Marking

• In conformity with European Union Low Voltage
Directive 2006/95/CE and Electromagnetic com­patibility directive 2004/108/CE

21

GLOW UP

GLOW UP C

C

HANNEL FUNCTIONS

C

HANNEL CHANNEL MODE

RED

GREEN

BLUE

WHITE

DIMMER

STOP / STROBE

MACRO COLOR

MACRO TIMING

MACRO FADING

1

2

3

4

5

6

7

8

9

GLOW UP TW

CHANNEL

INDEPENDENT CONSTANT INTENSITY MAX INTENSITY

CHANNEL MODE

COOL WHITE 6200°K

WARM WHITE 2700°K

STOP / STROBE

TUNABLE WHITE

DIMMER

STOP / STROBE

TUNABLE WHITE

DIMMER

STOP / STROBE

1

2

3

GLOW UP W

CHANNEL CHANNEL MODE

DIMMER

STOP / STROBE

1

2

22

GLOW UP

BIT % EFFECT

255 100

COLOUR INSERTED

0 0.0

COLOUR EXCLUDED

CHANNEL 1

R

ED

CHANNEL 2

G

REEN

CHANNEL 3

B

LUE

• COLOUR MIXING - channel 1 - 2 - 3

O

peration with option color mixing: RGB

B

IT

%

EFFECT

255 100

WHITE

0 0.0

BLACK

• WHITE - channel 4

• DIMMER - channel 5

BIT % EFFECT

255 100 OPEN (LIGHT)

CLOSED (BLACK)0 0.0

• STOP / STROBE - channel 6

•

MACRO COLOR - channel 7

BIT % EFFECT

248
2

40
232
224
220
216
212
208
204
2

00
196
192
188
184
180
176
172
168
164
1

60
156
152
148
144
140
136
132
128
124
120
116
112
1

08
104
100

96
92
88
84
80
76
72
68
64
60
56
52
48
44
40
36
32
28
24
20

0

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

255
2

47
239
231
223
219
215
211
207
2

03
199
195
191
187
183
179
175
171
167
1

63
159
155
151
147
143
139
135
131
127
123
119
115
1

11
107
103

99
95
91
87
83
79
75
71
67
63
59
55
51
47
43
39
35
31
27
23
19

COLD TONE
WARM TONE
PASTEL TONE
SEQ1
SKELTON EXOTIC SANGRIA
FLESH PINK
CHERRY ROSE
MAYAN SUN
LIGHT SALMON
COOL BLUE
URBAN BLUE
ROSE INDIGO
ALICE BLUE
BRIGHT BLUE
MAUVE
ENGLISH ROSE
FIRE
S

URPRISE PEACH
SCARLET
SURPRISE PINK
JUST BLUE
CHOCOLATE
DARK LAVENDER
A

PRICOT
PALE LAVENDER
DEEP GOLDEN AMBER
GOLDEN AMBER
MEDIUM BLUE
BRIGHT PINK
DARK BLUE
MED BLUE GREEN
BLUE 2
MAGENTA 2
DARK PINK
LIGHT ROSE
O

RANGE 2
S

TRAW
YELLOW 2
WHITE 2500
WHITE 3200
WARM WHITE
COOL WHITE
FULL WHITE
SKY BLUE
AQUAMARINE
VIOLET
PINK
ORANGE
WHITE
MAGENTA
CYAN
YELLOW
B

LUE
GREEN
RED
N

ONE

GLOW UP C

23

GLOW UP

•

COOL WHITE - channel 1

• WARM WHITE - channel 2

GLOW UP TW

• STOP / STROBE - channel 3

BIT % EFFECT

255 100 WARM WHITE

COOL WHITE 0 0.0

•

TUNABLE WHITE - channel 1

• WARM WHITE - channel 2

BIT % EFFECT

255 100 OPEN (LIGHT)

CLOSED (BLACK)

0 0.0

• STOP / STROBE - channel 3

INDEPENDENT

I

NDEPENDENT MODE

COOL WHITE 6200°K

WARM WHITE 2700°K

STOP / STROBE

CONSTANT INTENSITY

C

ONSTANT INTENSITY MAX INTENSITY

MAX INTENSITY

C

ONSTANT INTENSITY & MAX INTENSITY MODE

TUNABLE WHITE

DIMMER

STOP / STROBE

TUNABLE WHITE

DIMMER

STOP / STROBE

100

6

200°C 4200°C 2700°C

0

50

C

OOL WARM

COOL WARM

100

0

50

100

6

200°C 4200°C 2700°C

0

50

100

0

50

BIT % EFFECT

255 100 WHITE INSERTED

WHITE EXCLUDED0 0.0

B

IT

%

EFFECT

255 100 WHITE INSERTED

WHITE EXCLUDED0 0.0

• DIMMER - channel 1

BIT % EFFECT

255 100 OPEN (LIGHT)

CLOSED (BLACK)0 0.0

• STOP / STROBE - channel 2

GLOW UP W

CLAY PAKY г. Москва, Краснопахорское пос., д. Красная Пахра, д.57 Тел: [phone] Web:

www.scircus.ru E-mail: [e-mail]