Clay Paky WATER COLUMN User Manual
5 cm
®
ENGLISH
WATER COLUMN
ongratulations on choosing a Clay Paky product! We thank you for your
C
ustom. Please note that this product, as all the others in the rich Clay Paky
c
range, has been designed and made with total quality to ensure excellent
erformance and best meet your expectations and requirements.
p
NSTRUCTIONS MANUAL
I
Carefully read this instructions manual in its entirety and keep it safe for future
eference.
r
It is essential to know the information and comply with the instructions given
in this manual in order to ensure the fitting is installed, used and serviced
orrectly and safely.
c
CLAY PAKY S.p.A. disclaims all liability for damage to the fitting or to other
roperty or persons deriving from installation, use and maintenance that have
p
ot been carried out in conformity with this instructions manual, which must
n
always accompany the fitting.
LAY PAKY S.p.A. reserves the right to modify the characteristics stated in
C
his instructions manual at any time and without prior notice.
t
1
It is permissible to mount the fitting on normally flammable surfaces.
• Maximum ambient temperature
For the fitting to operate well and reliably, the ambient temperature should not
exceed 35°C (95°F).
• IP20 protection rating
The fitting is protected against penetration by solid bodies with a diameter of over
12 mm (0.47”) (first digit 2), but not against dripping water, rain, splashes or jets of
water (second digit 0).
• Protection against electrical shock
This fitting is classified, in accordance with the type of protection against electrical
shock, in Class I. It must therefore be connected to a power supply system with
efficient earthing.
It is, moreover, recommended to protect the supply lines of the fitting from indirect
contact and/or shorting to earth by using appropriately sized residual current
devices.
SAFETY INFORMATION
2
npacking
• U
pen the cardboard box, remove the device from the packaging and place it on the
O
floor.
emove all the accessories supplied as standard from the packaging.
R
• Packing contents
Besides the projector, the packing also
ontains the following accessories:
c
This instructions manual
-
ode 099561 (1).
c
N. 1 socket for mounting on cable
-
ode 030210 (2).
c
N. 1 lamp Decostar 12V 50W
-
ode L10056 (3).
c
UNPACKING AND PREPARATION
2
3
1
Cylinder cleaning
•
f the cylinder is dusty, clean it with water and neutral soap only, and dry with a soft,
I
non-abrasive cloth.
Caution: Use an absorbent cloth (4) to protect the gap where the cylinder connects
o the base, to ensure water cannot get in and damage the electric parts.
t
• Fitting the lamp
Refer to the instructions for changing the lamp
provided in section 3 MAINTENANCE.
• Installing the device
The unit must be mounted on the floor or on a
stable structure able to support the total weight
of the cylinder when filled with water.
Rest the unit on the special shock-resistent
rubber pads (5).
5
6
ENGLISH
4
• Hooking up to the supply mains
The operations for connecting to the electricity mains must be carried out by a
qualified electrical installer.
Check that the mains frequency and voltage correspond to the frequency and
voltage for which the projector is designed, given on the electrical data label.
This label also gives the input power. Refer to this to evaluate the maximum number
of fittings to connect to the electricity line in order to avoid overloading. es.
• Maintenance
Before starting any operation on the device, disconnect the mains power supply.
The maximum temperature of the device’s outside surface when at full operating
temperature is 60°C (140°F).
After switching off, do not remove any part of the device for 5 minutes, after which
there is virtually no risk that the lamp will explode. If the lamp has to be replaced,
wait a further 10 minutes to avoid burns. The device is designed so that any pieces
of broken glass produced if the lamp explodes will be retained; to ensure this, the lid
giving access to the lamp compartment must be closed when the device is in
operation.
• Lamp
- Carefully read the "operating instructions" provided by the lamp manufacturer.
- Immediately replace the lamp if damaged or deformed by heat.
The products referred to in this manual conform to the European
Community Directives to which they are subject:
• Low Voltage 2006/95/CE
• Electromagnetic Compatibility 2004/108/CE
•
Filling the cylinder
An absorbent cloth (4) should be placed at the
base of the cylinder before filling starts.
Once the Water Column has been positioned
as required, fill it to 5 cm below the top rim
using distilled water (capacity about 30 litres)
to minimise the formation of scale deposits.
When filling, take care not to allow water to
flow along the outside of the hose, or into the
opening in the base.
After filling, remove the protective soft cloth
and close the top of the cylinder by fitting the
cap provided (6).
4
3
1975
77,76”
ø150
ø5,91”
285
11,22”
356
14,02”
356
14,02”
L
N
onnecting to the mains power supply
• C
The device must be connected to the electricity supply system by means of the
onnector (2) provided.
c
ach device should be connected by means of a switch of its own, so that it can be
E
witched on and off separately from a distance.
s
4
HE LAMP DOES NOT COME ON
T
O OR TOO FEW BUBBLES
N
OLOUR DISC DOES NOT TURN
C
IGHT TOO DIM
L
TROUBLESHOOTING
PROBLEMS
2
ower supply
P
After all the operations described above have been carried out, supply power to the
device and check that the lamp lights up, and that bubble production and the rotation
f the colour disc begin.
o
3
•
Changing the lamp
ndo the wing-nuts (8) and open the lid
U
(7) giving access to the lamp compartment. Remove the faulty lamp (9) from
he socket (10), then take the new lamp
t
rom its pack. Read the "instructions for
f
use" provided by the lamp manufacturer
arefully, and fit it into the socket (10),
c
checking that the tabs are properly positioned. Replace the lid (7) and tighten the
wing-nuts (8).
MAINTENANCE
9
7 8
POSSIBLE CAUSES
•
Lamp burnt out.
•
No mains power supply.
•
Transformer has failed.
•
Compressor has failed.
•
orous element dirty.
P
•
otor has failed.
M
•
Dust or grease deposits.
5
ower supply
P
•
100-120V 60Hz
•
200-240V 50Hz
The projector is designed to work at
the frequency and voltage given on
the electrical data label on the back of
the appliance.
Lamp
Halogen dichroic lamp.
- Voltage: 12V.
- Power: 50W.
- Nominal lifetime: 4,000 hours.
- Colour temperature: 3,100 K.
- Cap: GU5,3.
TECHNICAL DATA
CHECKSAND REMEDIES
eplace the lamp.
R
Check that the power supply
onnector is receiving power, and/or
c
hat the fuses have not blown.
t
ontact an authorised technician.
C
ontact an authorised technician.
C
Contact an authorised technician..
Contact an authorised technician.
lean (see instructions).
C
perating position
O
Operates in vertical position.
Weight, capacity and dimensions
•
Weight: 12 Kg (empty) (26 lbs 6 ozs).
•
Capacity: about 30 litres.
10
•
Changing the fuses
Extract the fuse-box (11), taking hold of it
by the side tangs. Replace the blown
fuses with new fuses of the type stated on
the label (12) on the fuse-box (11) and put
the box back in place.
12
13
•
Routine cleaning
To maintain optimum performance and
efficiency over the long-term, the parts
where dust and grease accumulate must
be cleaned periodically. To remove dirt
from the protective glass (13) of the lamp
and colour filters (14), use a soft cloth
dipped in any window-cleaning liquid.
The inside surface of the cylinder should be cleaned every year, emptying out the
water it contains.
Clean the outside and inside of the cylinder using water with neutral soap only.
Dry with a soft (non abrasive) cloth.
14
11
Colour disc
Continuously rotating colour disc
1 rev/min, 8 colours: red, blue,
orange, violet, green, pink, yellow
and white.
The colour filters on the wheel can
easily be replaced with other filters in
polycarbonate or dichroic glass
Bubbles
•
Bubble generation cycle (interval
between bursts): 3 seconds.
•
Duration of burst: 4.5 seconds.
Maximum power absorption
110VA.
Safety devices
•
2 line fuses.
•
Degree of protection IP20.
•
Conforms to EC directives.
Body
•
ABS base.
•
Clear plastic (PMMA) cylinder.
4
Loading...