Clay Paky SPHERISCAN C11260, SPHERILIGHT C11270 Instruction Manual

1

INSTRUCTION MANUAL

Congratulations on choosing a Clay Paky product!
We thank you for your custom.
Please note that this product, as all the others in the rich Clay
Paky range, has been designed and made with total quality to
ensure excellent performance and best meet your expectations
and requirements.

ENGLISH

SPHERISCAN

SPHERILIGHT

C11260

C11270

PR

E

LIM

IN

A

R

Y

INDEX

Page Contents

2 Safety Information

4 Unpacking and preparation

5 Installation and start-up

6 Control panel

8 Menu setting

16 Maintenance

26 Technical information

27 Cause and solution of problems

28 Channel functions

2

SPHERISCAN - SPHERILIGHT

Carefully read this instruction manual in its entirety and keep it safe for future reference. It is essential to know the
i

nformation and comply with the instructions given in this manual to ensure the fitting is installed, used and serviced
correctly and safely. CLAY PAKY S.p.A. disclaims all liability for damage to the fitting or to other property or persons
deriving from installation, use and maintenance that have not been carried out in conformity with this instruction
manual, which must always accompany the fitting. CLAY PAKY S.p.A. reserves the right to modify the
characteristics stated in this instruction manual at any time and without prior notice.

• Installation

Make sure all parts for fixing the projector are in a good state of repair.
Make sure the point of anchorage is stable before positioning the projector.
The safety chain must be properly hooked onto the fitting and secured to the framework, so that, if the primary
support system fails, the fitting falls as little as possible.
If the safety chain gets used, it needs to be replaced with a genuine spare.

• Minimum distance of illuminated objects

The projector needs to be positioned so that the objects hit by the beam of light are at least 3 metres (9’10”) from
the lens of the projector.

• Minimum distance from flammable materials

The projector must be positioned so that any flammable materials are at least 0.20 metres (8") from every point on
the surface of the fitting.

• Maximum ambient temperature

Do not operate the fixture if the ambient temperature (Ta) exceeds 40° C (104° F).

• IP54 protection rating

The fixture is protected against dust (first digit 5) and splash (second digit 4).

• Protection against electrical shock

Connection must be made to a power supply system fitted with efficient earthing (Class I appliance according to
standard EN 60598-1).
It is, moreover, recommended to protect the supply lines of the projectors from indirect contact and/or shorting to
earth by using appropriately sized residual current devices.

• Connection to mains supply

Connection to the electricity mains must be carried out by a qualified electrical installer.
Check that the mains frequency and voltage correspond to those for which the projector is designed as given on the
electrical data label.
This label also gives the input power to which you need to refer to evaluate the maximum number of fittings to
connect to the electricity line, in order to avoid overloading.
If the projector is used in residential environment, in some cases it might be necessary to adopt appropriate
measures to avoid EMI disturbances to broadcast receiver equipment.

• Temperature of the external surface

The maximum temperature that can be reached on the external surface of the fitting, in a thermally steady state, is
150°C (302°F).

• Maintenance

Before starting any maintenance work or cleaning the projector, cut off power from the mains supply.
After switching off, do not remove any parts of the fitting for at least 10 minutes. After this time the likelihood of the
lamp exploding is virtually nill. If it is necessary to replace the lamp, wait for another 20 minutes to avoid getting burnt.
The fitting is designed to hold in any splinters produced by a lamp exploding. The lenses must be mounted and, if
visibly damaged, they have to be replaced with genuine spares.

• Lamp

The fitting mounts a high-pressure lamp that needs an external igniter. This igniter is fitted onto the apparatus.

- Carefully read the "operating instructions" provided by the lamp manufacturer.

- Immediately replace the lamp if damaged or deformed by heat.

• Photobiological Safety

CAUTION. Do not look directly at the light source.
Do not look at the light beam with optical devices or any other tool that could cause light convergence.
The fixture must be positioned so that the minimum distance between the front lens and human eye is at least 2
metres to prevent personal photobiological risks.

SAFETY INFORMATION

IP54

3

tc150°C

Risk Group 1

According to

EN 62471

EN

3

SPHERISCAN - SPHERILIGHT

This product is intended for the following areas of application:
studios, stages, theaters, exhibitions, trade fairs, events, theme parks, entertainment venues, architectural lighting
and similar.

Not suitable for household illumination

Not for residential use

• Battery

This product contains a rechargeable lithium iron tetraphosphate battery. To preserve the environment, please
dispose the battery at the end of its life according to the regulation in force.

Disposing

This product is supplied in compliance with European Directive 2012/19/EU - Waste Electrical and Electronic
Equipment (WEEE). To preserve the environment please dispose/recycle this product at the end of its life according
to the local regulation.

LiFePO4

The products to which this manual refers comply with the European Directives pursuant to:

• 2006/95/EC - Safety of electrical equipment supplied at low voltage (LVD)

• 2004/108/EC - Electromagnetic Compatibility (EMC)

• 2011/65/EU - Restriction of the use of certain hazardous substances (RoHS)

• 2009/125/EC - EcoDesign requirements for Energy-related Products (ErP)

EN

IT

DE

ES

FR

RU

HOW TO GET YOUR SAFETY INSTRUCTIONS IN MULTILINGUAL VERSION

You may always download the multilingual Safety Instruction manual for this Clay Paky product from:

http://www.claypaky.it/en/download

Ref: [FIS00M – Safety Information Spheriscan / Spherilight]

COME OTTENERE LE INFORMAZIONI DI SICUREZZA NELLA VERSIONE MULTILINGUE

Puoi sempre scaricare la versione multilingue delle Informazioni di Sicurezza per questo prodotto Clay Paky al
seguente link:

http://www.claypaky.it/en/download

Rif: [FIS00M – Safety Information Spheriscan / Spherilight]

SO ERHALTEN SIE IHR INFORMATIONEN ZUR SICHERHEIT IN DER MEHRSPRACHIGEN VERSION

Sie können die mehrsprachige Version des Handbuchs mit Sicherheitshinweisen fur dieses Clay Paky- Produkt
unter folgendem Link herunterladen:

http://www.claypaky.it/en/download

Ref: [FIS00M – Safety Information Spheriscan / Spherilight]

COMO OBTENER TU INFORMACIONES DE SEGURIDAD EN LA VERSION MULTILINGUE

Siempre puedes descargar la versión multilingue del Manual de Instrucciones de Seguridad para este producto
Clay Paky en el siguiente enlace

http://www.claypaky.it/en/download

Ref: [FIS00M – Safety Information Spheriscan / Spherilight]

COMMENT OBTENIR VOTRE CONSIGNES DE SÉCURITÉ DANS LA VERSION MULTILINGUE

Vous pouvez toujours télécharger la version multilingue du Manuel d’Instructions de Sécurité pour ce produit Clay
Paky au lien suivant :

http://www.claypaky.it/en/download

Réf. : [FIS00M – Safety Information Spheriscan / Spherilight]

ГДЕ ДОСТАТЬ ИНСТРУКЦИЮ ПО ТЕХНИКЕ БЕЗОПАСНОСТИ НА НЕСКОЛЬКИХ ЯЗЫКАХ

Вы всегда можете скачать многоязычную инструкцию по технике безопасности для данного изделия Clay
Paky по ссылке:

http://www.claypaky.it/en/download

Наименование: [FIS00M – Safety Information Spheriscan / Spherilight]

4

SPHERISCAN - SPHERILIGHT

UNPACKING AND PREPARATION

1

Installing the projector - Fig. 2
The projector can be installed on the floor resting, on a truss or on the ceiling or wall.

WARNING: with the exception of when the projector is positioned on the floor, the safety cable must be fitted. (Cod. 105041/001 available on request).
This must be securely fixed to the support structure of the projector and then connected to the fixing point as shown on the pictures above.

2

Packing contents - Fig. 1

5

SPHERISCAN - SPHERILIGHT

2

1

1

2

3

3

INSTALLATION AND START-UP

Connecting and disconnecting power cable - Fig. 3

6

SPHERISCAN - SPHERILIGHT

Switching on the projector - Fig. 6
Press the switch. The projector starts resetting the effects. At the same time, the following information scrolls on the display:

The control panel (Fig. 6) has a display and buttons for the complete programming and management of the projector menu.
The display can be in one of two conditions: rest status and setting status. When it is in the rest status, the display shows the projector’s DMX
address and the Fixture ID address (if set).
During menu setting status, after a wait time (about 30 seconds) without any key having been pressed, the display automatically returns to rest status.
It should be noted than when this condition occurs, any possible value that has been modified but not yet confirmed with the

F

key will be cancelled.

CONTROL PANEL

1

2

Dmx Address

Warning Message

Fixture ID

6

Firmware
Version X.X.X
Date - Hour

Connecting to the control signal line (DMX) - Fig. 5

Use a cable conforming to specifications EIA RS-485: 2-pole twisted, shielded, 120Ohm characteristic impedance, 22-24 AWG, low capacity. Do not use
microphone cable or other cable with characteristics differing from those specified. The end connections must be made using XLR type 5-pin male/female
connectors. A terminating plug must be inserted into the last projector with a resistance of 120Ohm (minimum 1/4 W) between terminals 2 and 3.
IMPORTANT: The wires must not make contact with each other or with the metal casing of the connectors. The casing itself must be connected to the
shield braid and to pin 1 of the connectors.

Connecting to the mains supply - Fig. 4

Mains

4

5

xxx (Fixture ID)
Dmx Address xxx

System errors

E: .........................

W: .........................

SPHERISCAN - SPHERILIGHT

7

28

28

Reversal of the display - Fig. 7
To activate this function, press UP

B

and DOWN Ckeys simultaneously while the display is in the rest mode. This status will be memorised and

maintained even for the next time it will be switched on. To return to the initial state, repeat the operation all over again.

S

etting the projector starting address

On each projector, the starting address must be set for the control signal (addresses from 1 to 512).
The address can also be set with the projector switched off.

Setting the projector Fixture ID

On each projector, the Fixture ID address must be set for an easy identification of the fixtures in an installation (ID from 1 to 255).
The Fixture ID address can be set with the projector switched off.

7

Functions of the buttons - Using the menu

Setting addresses and options with the projector disconnected

The projector’s DMX address, as well as other possible operating options, can also be set when the appliance is disconnected from the electricity supply.
All that is needed is to press

F

to momentarily activate the display and thus access the settings. Once the required operations have been carried out,

the display will switch off again after a wait time of 30 seconds.

USING THE MENU:

1) Press

F

once – “Main Menu” appears on the display.

2) Use the UP

B

and DOWN Ckeys to select the menu to be used:

• Setup (Setup Menu): To set the setting options.

• Option (Option Menu): To set the operating options

• Informations (Informations Menu): To read the counters, software version and other information.

• Manual Control (Manual control Menu): To trigger the test and manual control functions.

• Test (Test Menu): To check the proper functionning of effects

• Advanced (Advanced Menu): Access to the "Advanced menu" is recommended for a trained technical personnel.
To enable the "Advanced" see pag.15.

3) Press

F

to display the first item in the selected menu.

4) Use the UP

B

and DOWN Ckeys to select the MENU items.

Confirms the displayed value, or activates the displayed function, or enters the successive
menu.

Decreases the value displayed (with auto-repetitions) or passes to the next item in the menu.

Increases the value displayed (with auto-repetitions) or passes to the previous item in a menu.

Return to the top level

Commute from units, tens, hundreds, in the "Address", "Fixture ID" and "Calibration" menù.

F

C

DOWN

B

UP

D

LEFT

E

RIGHT

8

SPHERISCAN - SPHERILIGHT

MENU SETTING

Main Menu Level 1 Level 2 Level 3 Choices / Values

SET UP

DMX Address

Æ Æ

001-512

Channel Mode

Æ Æ

Standard

Vector

Fixture ID

Æ Æ

000-255

Ethernet Interface

C

ontrol Protocol

Æ

Disabled

Art-net IP 2.x.x.x.

A

rt-net IP 10.x.x.x.

Art-net Custom IP

Repeat on DMX

Æ

Disabled

Enabled on primary

Universe

Æ

000-255

Custom IP Address

IP address byte 1
IP address byte 2
IP address byte 3
IP address byte 4

000-255
000-255
000-255
000-255

Custom IP Mask

IP mask byte 1
IP mask byte 2
IP mask byte 3
IP mask byte 4

000-255
000-255
000-255
000-255

OPTION

Lamp DMX

Æ Æ

On / Off

Pan / Tilt Pan Short-cut

Æ

On / Off

Color

Color Mixing

Æ

RGB / CMY

Fix Wheel Shortcut

Æ

On / Off

Shutter

Shutter On Error

Æ

On / Off

Dimmer On Shutter

Æ

On / Off

Display

Æ Æ

On / Off

Settings

Default Preset

Reset To Default

Go Back

Are you sure

?

Yes / No

User Preset 1

Load preset 1

Save to preset 1

Are you sure

?

Yes / No

User Preset 2

Load preset 2

Save to preset 2

Are you sure

?

Yes / No

User Preset 3

Load preset 3

Save to preset 3

Are you sure

?

Yes / No

9

SPHERISCAN - SPHERILIGHT

M

ain Menu

L

evel 1

L

evel 2

L

evel 3

C

hoices / Values

INFORMATION

System Errors

Æ Æ

Read / Reset

F

ixture Hours

Total Hours

Æ

Read

Partial Hours

Æ

Read / Reset

L

amp Hours

T

otal Hours

Æ

R

ead

Partial Hours

Æ

Read / Reset

Lamp Strikes

Total Strikes

Æ

Read

Partial Strikes

Æ

Read / Reset

System Version

CPU brd

Æ

Fw.rev. / Hw.rev.

com.dev

Æ

Fw.rev.

0:PT-3f

Æ

Fw.rev. / Hw.rev.

1:8-Ch

Æ

Fw.rev. / Hw.rev.

2:8-Ch

Æ

Fw.rev. / Hw.rev.

3:8-Ch

Æ

Fw.rev. / Hw.rev.

Board Diagnostic

0:PT-3f

Æ

Status / Err%

1:8-Ch

Æ

Status / Err%

2:8-Ch

Æ

Status / Err%

3:8-Ch

Æ

Status / Err%

DMX Monitor Channels

Æ

Value / Percentage

Fans Monitor

Board

Æ

Speed (RPM)

Lamp

Æ

Speed (RPM)

Lamp

Æ

Speed (RPM)

Eff. IN

Æ

Speed (RPM)

Eff. IN

Æ

Speed (RPM)

Ball. IN

Æ

Speed (RPM)

Ball. IN

Æ

Speed (RPM)

Sensor status Channels

Æ

n.a / On / Off

Rot. Gobo 1 Indexing

Æ Æ

Indexing Active

Indexing Required

Rot. Gobo 2 Indexing

Æ Æ

Indexing Active

Indexing Required

Network parameters

Æ Æ

IP Address

Æ Æ

IP Mask

Æ Æ

MAC Address

Continue

➔

10

SPHERISCAN - SPHERILIGHT

Main Menu Level 1 Level 2 Level 3 Choices / Values

MA

NUAL

C

ONTROL

L

amp

Æ Æ

O

n / Off

R

eset

Æ Æ

Y

es / No

Channel

Æ Æ

Value / Percentage

TEST

Pan / Tilt

Æ Æ

n.a.

Colour

Æ Æ

n.a.

Beam

Æ Æ

n.a.

Gobo

Æ Æ

n.a.

A

ll

Æ Æ

n

.a.

ADVANCED Access Code 1234

U

pload Firmware Transfer ……..

A

re you sure

?

Yes / No

Setup Model Changing ……..

Are you sure

?

Yes / No

Calibration Channels 000 - 255

Rot. Gobo 1 Indexing

Starting procedure …..

Yes / No

Rot. Gobo 2 Indexing

Starting procedure …..

Yes / No

Menu Locking Unlock Code XXXX

11

SPHERISCAN - SPHERILIGHT

S

ET UP MENU

DMX ADDRESS

PLEASE NOTE: Without the DMX input signal, the displayed address (DMX Address) blinks.

It lets you select the address (DMX Address) for the control signal. A DMX address between 001 and 512 can be
s

elected.

CHANNEL MODE

This lets you select the projector operating mode, selecting one of the two available modes:

• Standard (see DMX-Channel Function)

• Vector (see DMX-Channel Function)

FIXTURE ID

It lets you set the “Fixture ID” to be assigned to the projector. An “ID” between 000 and 255 can be assigned.

ETHERNET INTERFACE

It lets you set Ethernet settings to be assigned to the projector as indicated below:

Control Protocol

It lets you select the “Control Protocol” Art-net to be assigned according to the control unit used; the options available are
the following:

• Disabled:

• Art-net on IP 2

• Art-net on IP 10

• Art-net Custom IP

If the Control Protocol option is set on Disabled, when an IP address (IP2, IP10 or IP Custom) is selected, the projector
immediately initializes the IP address that was just selected.
If the Control Protocol option is enabled (IP2, IP10 or IP Custom) and a new one is selected that is different from the
previous one, the projector must be restarted so that it will be correctly initialized.

Repeat on DMX

It lets you enable/disable the transmission of the Ethernet protocol by DMX signal to all the connected projectors.

• Disabled: DMX transmission disabled.

• Enabled on primary: DMX transmission enabled.

Universe

It lets you set the “DMX Universe” to be assigned to a series of projectors with values between 000 and 255.

Custom IP Address

It lets you to set the select the “IP Address” Art-net to be assigned, according to the control unit used, with values
between 000 and 255.

Custom IP Mask

It lets you to set the select the “IP Mask” Art-net to be assigned, according to the control unit used, with values between
000 and 255.

Continue

➔

12

SPHERISCAN - SPHERILIGHT

O

PTIONS MENU

L

AMP DMX

It lets you enable (ON) the lamp remote control channel. Select OFF to turn off or disable this option.

PAN / TILT
P

an Short-cut

Used for optimizing Pan change time (select ON) so that the Pan moves in the direction that requires shorter movement.
Select OFF to turn off or disable this option.

COLOR
Color mixing

It lets you set the CMY color mixing system:

• RGB color mixing mode (Red Green Blue)

• CMY color mixing mode (Cyan Magenta Yellow)

SHUTTER
Shutter on error

It lets you activate (ON) automatic "Stopper/Strobe" closing in the event of Pan/Tilt positioning error. Select OFF to turn
off or disable this option.

Dimmer on Shutter

Enables (select ON) the automatic closing of the Dimmer when the Strobe is completely closed. Select OFF to turn off or
disable this option.

DISPLAY

It lets you activate (ON) display brightness reduction after about 30 seconds in idle status. Select OFF to turn off or
disable this option.

SETTINGS

Used to save 3 different settings of the items in the option menu and relevant submenus.

• Default preset (*)

• User preset 1

• User preset 2

• User Preset 3

- Load preset 'X’ is used to recall a previously stored configuration.

- Save to preset ‘X’ is used to save the current configuration.

(*) DEFAULT PRESET
It lets you restore default values on all option menu items and relevant submenus.

Press the left and right arrows/keys simultaneously in the "main menu” to quickly restore default values
(DEFAULT PRESET).

13

SPHERISCAN - SPHERILIGHT

I

NFORMATION MENU

S

YSTEM ERRORS

It displays a list of errors that occurred when the projector was turned on.
To reset the SYSTEM ERRORS list, press OK. A confirmation message appears (Are you sure you want to clear error
list?). Select YES to confirm reset.

FIXTURE HOURS

It lets you view projector working hours (total and partial).

T

otal counter

It counts the number of projector working life hours (from construction to date).

Partial counter

It counts the number of projector partial working life hours from the last reset to date.

Press OK to reset the partial counter. A confirmation message appears on the display (Are you sure ?)
Select YES to confirm reset.

LAMP HOURS

It lets you view lamp working hours (total and partial).

Total counter

It counts the number of projector working hours with the lamp on (from construction to date).

Partial counter

It counts the number of lamp partial working hours from the last reset to date.

Press OK to reset the partial counter. A confirmation message appears on the display (Are you sure ?)
Select YES to confirm reset.

LAMP STRIKES

It lets you view how many times the lamp was turned on (total and partial).

Total counter

It counts the number of times the lamp was turned on (from construction to date).

Partial counter

It counts the number of times the lamp was turned on from the last reset to date.

Press OK to reset the partial counter. A confirmation message appears on the display (Are you sure ?)
Select YES to confirm reset.

SYSTEM VERSION

It lets you view the hardware and software versions for each electronic board in the projector.

• CPU brd (CPU board)

• 0: PT-3f (Pan / Tilt board)

• 1: 8-Ch (8-channel board)

• 2: 8-Ch (8-channel board)

• 3: 8-Ch (8-channel board)

BOARD DIAGNOSTIC

It lets you view the percent errors for each electronic board installed in the projector

• 0: PT-3f (Pan / Tilt board)

• 1: 8-Ch (8-channel board)

• 2: 8-Ch (8-channel board)

• 3: 8-Ch (8-channel board)

DMX MONITOR

It lets you view the level of projector DMX channels in bit (Val) and in percent.

Continue

➔

14

SPHERISCAN - SPHERILIGHT

FANS MONITOR

It lets you view the speed of each fan installed in the projector:

•

Board (board cooling fan)

• Lamp (lamp cooling fan)

• Ball.IN (Ballast cooling fan, air-flow IN)

• Effect.IN (Effects cooling fan, air-flow IN)

SENSOR STATUS

It lets you check the correct operations of each "sensor” installed in the projector, each channel is associated with one of
t

he following three parameters:

• n.a.= sensor not available

• ON= sensor working

• OFF= sensor defective

ROT GOBO 1 INDEXING

It lets you check whether the rotating gobo wheel 1 gobo indexing procedure should be run, if indexed, "Indexing Active"
appears on the display, otherwise "Indexing required!” appears

If necessary, indexing should be activated from the Advanced menu.

ROT GOBO 2 INDEXING

It lets you check whether the rotating gobo wheel 2 gobo indexing procedure should be run, if indexed, "Indexing Active"
appears on the display, otherwise "Indexing required!” appears

If necessary, indexing should be activated from the Advanced menu.

NETWORK PARAMS

Lets you view the projector "Network" parameters meaning:

IP address: Internet Protocol address (two projectors must not have the same IP address)
IP mask: 255.0.0.0
Mac address: Media Access Control; the projector’s Ethernet Address.

15

SPHERISCAN - SPHERILIGHT

M

ANUAL CONTROL

LAMP

It lets you turn the lamp on (ON) or off (OFF) from the projector control panel.

RESET

It lets you reset the projector from the projector control panel.

CHANNEL

It lets you set the channel DMX levels from the projector control panel (value between 0 and 255 bit or between 0% and
100%).

TEST MENU

It lets you test the correct operations of effects using saved Tests.

ADVANCED MENU

To open the “Advanced Menu”, enter the code (1234)

UP LOAD FIRMWARE

It lets you transfer "firmware" from one projector to all other connected projectors. A confirmation message appears on
the display (Are you sure ?) Select YES to confirm or NO to abort this operation.

SETUP MODEL

It lets you change the projector model (operation probably necessary after replacing the CPU during repairs). A
confirmation message (Are you sure ?) appears on the display Select YES to confirm (the list of available and selectable
projectors appears) or NO to abort this operation.

CALIBRATION

It lets you make small mechanical adjustments on some effects to perfectly align projectors from the control panel.

Factory default

It lets you restore default "Calibration” values (128 bit) on all channels.

ROT GOBO INDEXING

It lets you run the rotating gobo wheel gobo indexing procedure. This operation may be necessary after projector
maintenance/cleaning.

MENU LOCKING

It allows you to assign a password to lock the access to the user menu, so that only users know the password can change
settings. The password is 4-digit number.

1

3

2

4

8

Opening the covers - Fig. 8.

16

SPHERISCAN - SPHERILIGHT

MAINTENANCE

17

SPHERISCAN - SPHERILIGHT

1

2

3

9

Fan assembly removal - Fig. 9.

Continue

➔

18

SPHERISCAN - SPHERILIGHT

1

2

3

6

4

5

7

8

1

0

Fan /Driver assembly removal - Fig. 10.

19

SPHERISCAN - SPHERILIGHT

1

1

Periodical cleaning - Fig. 11
To ensure optimal operation and performance for a long time it is essential to periodically clean the parts subject to dust and grease deposits. The
frequency with which the following operations are to be carried out depends on various factors, such as the amount of the effects and the quality of the
working environment (air humidity, presence of dust, salinity, etc.).
Use a soft cloth dampened with any detergent liquid for cleaning glass to remove the dirt from the reflectors, from the lenses and filters. It is recommended
that the projector undergoes an annual service by a qualified technician for special maintenance involving at least the following operations:

• General cleaning of internal parts.

• Restoring lubrication of all parts subject to friction, using lubricants specifically supplied by Clay Paky.

• General visual check of the internal components, cabling, mechanical parts, etc.

• Electrical, photometric and functional checks; eventual repairs.

Continue

➔

WARNING: The best way to clean the surface
is to pour ethanol on all the surface with a
wash bottle for example and then dry with
compressed air.
You can also clean with a soaked soft cloth for
more stubborn stains. If you don’t have
ethanol use a soft glass cleaner.

20

SPHERISCAN - SPHERILIGHT

2

1

1

2

Cleaning of the filters - Fig. 12.

2

1

21

SPHERISCAN - SPHERILIGHT

1

3

A

A

A

2

1

3

14

Opening and closing lamp compartment - Fig. 13

Lamp change - Fig 14

Take the new lamp out of its package and insert in the fitting.

WARNING: do not touch the lamp’s envelope with bare hands. Should this happen, clean the bulb with a cloth soaked in alcohol and dry it
with a clean, dry cloth.

CAUTION: Fast lamp ON-OFF cycles (for example 10 minutes ON / 10 minutes OFF) will reduce the lamp life.

Continue

➔

16

Rotating gobo wheel - Fig. 16.
ATTENTION:

- Before use custom gobos contact Clay Paky;

- The original gobos have a special coating designed specifically to resist to the high temperatures;

- The rotating gobo wheel only use dichroic glass gobos (it is not possible to use metal gobos);

- For more information contact Clay Paky.

22

SPHERISCAN - SPHERILIGHT

Replacing fuse - Fig. 15

3

2

1

Fuse
6,3 x 32mm 10AT (030470)

1

5

23

SPHERISCAN - SPHERILIGHT

Installation under the stage - Fig. 17.
To install the projector under the stage, it is suggested to remove the main bracket and mount the two handles (part number C21090) that allow you to
drop easily the projector.

2

1

1

3

3

4

4

ø

1

0

(

0

.

3

9

"

)

522 ±0,5

(20.55")

470

(18.50")

80

(3.15")

390

(15.35")

550

(21.65")

162 ±0,3

(6.38")

R

20

(

0.79")

5

6

R

195

(

7.68"

)

450

(17.72")

C21090

1

7

Continue

➔

24

SPHERISCAN - SPHERILIGHT

How to fit the fans covers - Fig. 18.
Depending on how the projector is installed, the covers fan must be positioned so that in case of rain, the water flows in the correct way.

0° ÷ +45°

0° ÷ -45°

1

180°

2

180°

180°

180°

3

2

3

180°

3

1

8

25

SPHERISCAN - SPHERILIGHT

1

6

3

4

5

2

1

9

Battery removal - Fig. 19

This product contains a rechargeable lithium iron tetraphosphate battery. To preserve the environment, please dispose the battery at the end
of its life according to the regulation in force.

LiFePO4

Continue

➔

26

SPHERISCAN - SPHERILIGHT

TECHNICAL INFORMATION

4

97

(19.57")

4

15

(

16.34")

358

(

14.09")

886

(

34.88")

498

(19.61")

4

15

(

16.34")

550

(21.65")

5

22

(20.55")

386

(15.20")

1

62

(6.38")

ø

11

(0.

43"

)

512

(

20.16")

374

(

14.72")

886

(

34.88")

198

(7.80")

1

84

(7.24")

300

(11.81")

184

(7.24")

1

98

(7.80")

Power supplies:

200/240V 50/60 Hz

Input power:

1600VA

Total lumen output:

20.000lm @ 1200W

Light source:

Lamp OSRAM Lok-it 1400-PS
Color Temperature: 6.000 K

- Life: 750 hrs

- CRI 95

- Luminoux flux: 120000 lm

- Base PGJ28 Lok-it!

Motors:
25 stepper motors, operating with microsteps,
totally microprocessor controlled

Inputs:

• DMX 512

• ART-NET

Moving mirror:

• PAN
Angle Rotation: 360° continuos rotation

• TILT
Angle Rotation: 60°

Weight:
35 Kg (77 lbs), 32 Kg (70.5 lbs) without bracket

Dimensions:

• (L x W x H): 370 x 390 x 885 mm – with bracket:
485 x 500 x 885 mm

• (L x W x H): 14.56 x 15.35 x 34.84 inches – with
bracket: 19.09 x 19.68 x 34.84 inches

IP rating:

• IP54

• Totally protected against the entry of solid bodies

• Protected against splashing of water

Safety devices:

Automatic break in power supply in case of
overheating or failed operation of cooling system

Cooling:
Forced ventilation with fans

Body:

• Aluminium and steel structure with plastic cover

• Circular handle and moving bracket for
transportation

Working position:

• Vertical or orizontal ±45° Working Position to
ensure IP54

• Hanging system: with fast-lock omega clamps
(1/4 turn) on bracket

Effects section:

• Lamp OSRAM Lok-it 1400-PS works at 1200 W

• Very precise 0-100% dimmer

• CMY System + Linear CTO

• Fast stop/strobe effect

• N°1 Colour Wheel with 7 color filter

• N° 2 Wheels with 6+6 rotating gobo
(image ø26 mm)

• N° 1 Graphics Wheel
(Interchangeable with fixed gobo Wheel)

• N° 1 16 fast Iris (16 blades)

• N° 1 Rotating Prism with 4 faces

• N° linear Frost (heavy)

• 13° - 34° Optical Zoom
(Diameter front lens ø80 mm)

Control and programming:

• DMX protocol signal: USITT DMX 512

• Display: LCD 128 x 64 bit, backlit LED, white on
black

• Pan and Tilt Resolution: 16 bit

• Focus Indexing Resolution: 16 bit

• Dimmer Resolution: 16 bit

• Rotation gobo Resolution: 16 bit

• Movement control: vectorial

• DMX signal connection: 5 pole XLR input and
output

• Software upload through DMX input / Ethernet
input

Electronics:

• Long life self-charging buffer battery.

• Function reset from control unit

• ON/OFF lamp control from the lighting desk.

• Function reset from the lighting desk.

• "AUTOTEST" function from menu.

• ARTNET

• Electronic monitoring with status error.

• Cooling system monitoring.

• DMX level monitoring on all channels.

• Internal data transmission diagnostics.

• Firmware Upgrade with no power.

• Firmware upload from another fixture.

27

SPHERISCAN - SPHERILIGHT

CAUSE AND SOLUTION OF PROBLEMS

THE PROJECTOR WILL NOT SWITCH ON

PROBLEMS

ELECTRONICS NON-OPERATIONAL

DEFECTIVE PROJECTION

REDUCED LUMINOSITY

POSSIBLE CAUSES CHECKS AND REMEDIES

No mains supply.
Lamp exhausted or defective.
Signal transmission cable faulty or disconnected.
Incorrect addressing.
Fault in the electronic circuits.
Lenses or reflector broken
Dust or grease deposited.

Check the power supply voltage.
Replace the lamp. (See instructions).
Replace the cables.
Check addresses (see instructions).
Call an authorised technician.
Call an authorised technician.
Clean (see instructions).

SPHERISCAN

CHANNEL FUNCTION

28

SPHERISCAN - SPHERILIGHT

NB: To prevent accidental breakage of the effects,
which could collide with each other during transport,
before switching the projector OFF check that all the
projector Channels have been excluded (DMX level = 0%).

CHANNEL

CHANNEL MODE

STANDARD VECTOR

1 CYAN CYAN
2 MAGENTA MAGENTA
3 YELLOW YELLOW
4 COLOUR COLOUR
5 STOPPER / STROBE STOPPER / STROBE
6 DIMMER DIMMER
7 FINE DIMMER FINE DIMMER
8 IRIS IRIS

9 STATIC GOBO CHANGE STATIC GOBO CHANGE
10 ROTATING GOBO CHANGE ROTATING GOBO CHANGE
11 GOBO ROTATION GOBO ROTATION
12 FINE GOBO ROTATION FINE GOBO ROTATION
13 PRISM INSERTION PRISM INSERTION
14 PRISM ROTATION PRISM ROTATION
15 FROST FROST
16 ZOOM ZOOM
17 FOCUS FOCUS
18 FINE FOCUS FINE FOCUS
19 FUNCTION FUNCTION
20 RESET RESET
21 LAMP CONTROL LAMP CONTROL
22 PAN PAN
23 FINE PAN FINE PAN
24 PAN MIRROR ROTATION PAN MIRROR ROTATION
25 TILT TILT
26 FINE TILT FINE TILT
27 STRIP LED RED STRIP LED RED
28 STRIP LED GREEN STRIP LED GREEN
29 STRIP LED BLUE STRIP LED BLUE
30 - PAN/TILT TIME
31 - COLOUR TIME
32 - BEAM TIME
33 - ROTATING GOBO TIME

SPHERISCAN - SPHERILIGHT

29

C

hannel Mode

DMX

Value

Function

Standard Vector

1 1

CYAN

0 - 255 Linear Cyan movement

2 2

MAGENTA

0 - 255 Linear Magenta movement

3 3

YELLOW

0 - 255 Linear Yellow movement

4 4

COLOUR

0 - 15 Color 1
16 - 31 Color 2
32 - 47 Color 3
48 - 63 Color 4
64 - 79 Color 5
80 - 95 Color 6

96 - 111 Color 7

112 - 127 Color 8

128 - 255

Continuous rotation at linearly variable speed from Slow (4.4 rph) to
Fast (160 rpm)

5 5

STOPPER / STROBE

0 - 3 Light OFF

4 - 103

Strobe at linearly variable frequency
from low (1 flash/sec) to high (12 flashes/sec)

104 - 107 Light ON

108 - 207

Pulsation at linearly variable speed

from slow to fast
208 - 212 Light ON
213 - 225 Random Strobe at low frequency
226 - 238 Random Strobe at medium frequency
239 - 251 Random Strobe at high frequency
252 - 255 Light ON

6 6

DIMMER

0 - 255

Light output linearly increase from no-light to maximum brightness.

Dimmer blades move from totally closed to totally open in xxx seconds

at maximum speed.

7 7

DIMMER FINE

0 - 255 Fine Dimmer positioning

8 8

IRIS

0 - 127 Iris linearly open from minimum to maximum aperture
128 - 131 Maximum aperture
132 - 171 Iris pulsation from slow to fast speed
172 - 211 Iris pulsation from slow to fast speed with fast opening
212 - 251 Iris pulsation from slow to fast speed with fast closing
252 - 255 Maximum aperture

Continue

➔

30

SPHERISCAN - SPHERILIGHT

Channel Mode

DMX

Value

Function

Standard Vector

9 9

S

TATIC GOBO CHANGE

0 - 7 Empty position

8 - 15 Gobo 1
16 - 23 Gobo 2
24 - 31 Gobo 3
32 - 39 Gobo 4
40 - 47 Gobo 5
48 - 55 Gobo 6
56 - 63 Gobo 7
64 - 71 Gobo 8

72 - 113

Continuous gobo wheel clockwise rotation at linearly variable speed
from fast (60 rpm) to slow (5 rpm)

114 - 117 Stop rotation

118 - 159

Continuous gobo wheel counter-clockwise rotation at linearly variable

speed from slow (5 rpm) to fast (60 rpm)
160 - 171 Gobo 1 shakes at variable speed from slow (24 bpm) to fast (600 bpm)
172 - 183 Gobo 2 shakes at variable speed from slow (24 bpm) to fast (600 bpm)
184 - 195 Gobo 3 shakes at variable speed from slow (24 bpm) to fast (600 bpm)
196 - 207 Gobo 4 shakes …
208 - 219 Gobo 5 shakes …
220 - 231 Gobo 6 shakes …
232 - 243 Gobo 7 shakes …
244 - 245 Gobo 8 shakes …

10 10

ROTATING GOBO CHANGE

0 - 18 Empty position
19 - 37 Gobo 1
38 - 56 Gobo 2
57 - 74 Gobo 3
75 - 92 Gobo 4

93 - 111 Gobo 5
112 - 129 Gobo 6
130 - 150 Gobo 1 shakes at variable speed from slow (xx bpm) to fast (xx bpm)
151 - 171 Gobo 2 shakes at variable speed from slow (xx bpm) to fast (xx bpm)
172 - 192 Gobo 3 shakes at variable speed from slow (xx bpm) to fast (xx bpm)
193 - 213 Gobo 4 shakes at variable speed from slow (xx bpm) to fast (xx bpm)
214 - 234 Gobo 5 shakes at variable speed from slow (xx bpm) to fast (xx bpm)
235 - 255 Gobo 6 shakes at variable speed from slow (xx bpm) to fast (xx bpm)

31

SPHERISCAN - SPHERILIGHT

C

hannel Mode

D

MX

V

alue

F

unction

S

tandard Vector

11 11

GOBO ROTATION

0 - 21 Gobo indexing: 0° to 90° range
21 - 42 Gobo indexing: 90° to 180° range
42 - 63 Gobo indexing: 180° to 270° range
6

3 - 84 Gobo indexing: 270° to 360° range

84 - 105 Gobo indexing: 360° to 450° range

105 - 127 Gobo indexing: 450° to 540° range

128 - 190

Continuous gobo rotation at linearly variable speed from fast (180 rpm)
to slow (2.2 rph)

191 - 192 Stop rotation

193 - 255

Continuous gobo rotation at linearly variable speed from slow (2.2 rpm)
to fast (180 rpm)

12 12

FINE GOBO ROTATION

0 - 255 Fine Gobo Indexing

13 13

PRISM INSERTION

0 - 127 Prism out

128 - 255 Prism into the light beam

14 14

PRISM ROTATION

0 - 21 Prism indexing: 0° to 90° range
21 - 42 Prism indexing: 90° to 180° range
42 - 63 Prism indexing: 180° to 270° range
63 - 84 Prism indexing: 270° to 360° range

84 - 105 Prism indexing: 360° to 450° range

105 - 127 Prism indexing: 450° to 540° range

128 - 190

Continuous prism rotation at linearly variable speed from fast (80 rpm)
to slow (3 rph)

191 - 192 Stop rotation

193 - 255

Continuous prism rotation at linearly variable speed from slow (3 rph)
to fast (80 rpm)

15 15

FROST

0 - 255

Frost moves linearly into the light beam
Frost blades move from no-diffusion to maximum diffusion

16 16

ZOOM

0 - 255 Zoom linearly moves from narrow to wide beam

17 17

FOCUS

0 - 255 Focus moves linearly from far to near position

18 18

FINE FOCUS

0 - 255 Fine Focus positioning

Continue

➔

32

SPHERISCAN - SPHERILIGHT

Channel Mode

DMX

Value

Function

Standard Vector

19 19

F

UNCTION

0 - 11 Unused range
12 - 24 Fast Pan / Tilt Speed (default)
25 - 37 Normal Pan / Tilt Speed
38 - 50 Conventional Dimmer curve
51 - 62 Linear Dimmer curve (default)

63 -113 Free
114 - 127 Free
128 - 140 Standard Dimmer curve
141 - 152 Fast Gobo change
153 - 163 Normal Gobo change (default)
164 - 255 Free

The functions are activated/selected passing through the unused
levels range and staying in the necessary range for 5 seconds

20 20

RESET

0 - 25 Unused range

26 - 76

Zoom Reset

Zoom Reset sequence is activated passing through the unused levels
range and staying in this range for 5 seconds

77 - 127

Pan / Tilt Reset

Pan/Tilt Reset sequence passing through the unused levels range and
staying in this range for 5 seconds

128 - 255

Complete Reset

All-effects Reset sequence passing through the unused levels range
and staying in this range for 5 seconds

21 21

LAMP CONTROL

0 - 25 Unused range

26 - 100

Lamp OFF
Lamp switch-off passing through the unused levels range and staying
in this range for 5 seconds

101 - 255

Lamp ON
Lamp switch-on passing through the unused levels range and staying
in this range for 5 seconds.

22 22

PAN

0 - 255 Pan Mirror movement/positioning from 0° to 360°

23 23

FINE PAN

0 - 255 Fine Pan positioning

24 24

PAN MIRROR ROTATION

0 Stop rotation

1 - 126 Mirror counter-clockwise rotation
127 - 129 Stop rotation
130 - 255 Mirror clockwise rotation

25 25

TILT

0 - 255 Tilt movement/positioning

26 26

FINE TILT

0 - 255 Fine Tilt positioning

33

SPHERISCAN - SPHERILIGHT

C

hannel Mode

D

MX

V

alue

F

unction

S

tandard Vector

27 27

STRIP LED RED

0 Led OFF

1 - 255 Led light linearly increase from low to maximum intensity

28 28

STRIP LED GREEN

0 Led OFF

1 - 255 Led light linearly increase from low to maximum intensity

29 29

STRIP LED BLUE

0 Led OFF

1 - 255 Led light linearly increase from low to maximum intensity

-

30

PAN-TILT TIME

0 - 255 Pan - Fine Pan - Tilt - Fine Tilt

-

31

COLOUR TIME

0 - 255 Cyan - Magenta –Yellow

-

32

BEAM TIME

0 - 255 Dimmer - Frost - Prism –Focus - Zoom

-

33

GOBO TIME

0 - 255 Rotating Gobo

Continue

➔

34

SPHERISCAN - SPHERILIGHT

SPHERILIGHT

CHANNEL

CHANNEL MODE

STANDARD VECTOR

1 CYAN CYAN
2 MAGENTA MAGENTA
3 YELLOW YELLOW
4 COLOUR COLOUR
5 STOPPER / STROBE STOPPER / STROBE
6 DIMMER DIMMER
7 FINE DIMMER FINE DIMMER
8 IRIS IRIS

9 STATIC GOBO CHANGE STATIC GOBO CHANGE
10 ROTATING GOBO CHANGE ROTATING GOBO CHANGE
11 GOBO ROTATION GOBO ROTATION
12 FINE GOBO ROTATION FINE GOBO ROTATION
13 PRISM INSERTION PRISM INSERTION
14 PRISM ROTATION PRISM ROTATION
15 FROST FROST
16 ZOOM ZOOM
17 FOCUS FOCUS
18 FINE FOCUS FINE FOCUS
19 FUNCTION FUNCTION
20 RESET RESET
21 LAMP CONTROL LAMP CONTROL
22 - COLOUR TIME
23 - BEAM TIME
24 - ROTATING GOBO TIME

35

SPHERISCAN - SPHERILIGHT

C

hannel Mode

DMX

Value

Function

Standard Vector

1 1

CYAN

0 - 255 Linear Cyan movement

2 2

MAGENTA

0 - 255 Linear Magenta movement

3 3

YELLOW

0 - 255 Linear Yellow movement

4 4

COLOUR

0 - 15 Color 1
16 - 31 Color 2
32 - 47 Color 3
48 - 63 Color 4
64 - 79 Color 5
80 - 95 Color 6

96 - 111 Color 7

112 - 127 Color 8

128 - 255

Continuous rotation at linearly variable speed from Slow (4.4 rph) to
Fast (160 rpm)

5 5

STOPPER / STROBE

0 - 3 Light OFF

4 - 103

Strobe at linearly variable frequency
from low (1 flash/sec) to high (12 flashes/sec)

104 - 107 Light ON

108 - 207

Pulsation at linearly variable speed

from slow to fast
208 - 212 Light ON
213 - 225 Random Strobe at low frequency
226 - 238 Random Strobe at medium frequency
239 - 251 Random Strobe at high frequency
252 - 255 Light ON

6 6

DIMMER

0 - 255

Light output linearly increase from no-light to maximum brightness.

Dimmer blades move from totally closed to totally open in xxx seconds

at maximum speed.

7 7

FINE DIMMER

0 - 255 Fine Dimmer positioning

8 8

IRIS

0 - 127 Iris linearly open from minimum to maximum aperture
128 - 131 Maximum aperture
132 - 171 Iris pulsation from slow to fast speed
172 - 211 Iris pulsation from slow to fast speed with fast opening
212 - 251 Iris pulsation from slow to fast speed with fast closing
252 - 255 Maximum aperture

Continue

➔

36

SPHERISCAN - SPHERILIGHT

C

hannel Mode

D

MX

V

alue

F

unction

S

tandard Vector

9 9

STATIC GOBO CHANGE

0 - 7 Empty position

8 - 15 Gobo 1
16 - 23 Gobo 2
24 - 31 Gobo 3
32 - 39 Gobo 4
40 - 47 Gobo 5
48 - 55 Gobo 6
56 - 63 Gobo 7
64 - 71 Gobo 8

72 - 113

Continuous gobo wheel clockwise rotation at linearly variable speed
from fast (60 rpm) to slow (5 rpm)

114 - 117 Stop rotation

118 - 159

Continuous gobo wheel counter-clockwise rotation at linearly variable

speed from slow (5 rpm) to fast (60 rpm)
160 - 171 Gobo 1 shakes at variable speed from slow (24 bpm) to fast (600 bpm)
172 - 183 Gobo 2 shakes at variable speed from slow (24 bpm) to fast (600 bpm)
184 - 195 Gobo 3 shakes at variable speed from slow (24 bpm) to fast (600 bpm)
196 - 207 Gobo 4 shakes …
208 - 219 Gobo 5 shakes …
220 - 231 Gobo 6 shakes …
232 - 243 Gobo 7 shakes …
244 - 245 Gobo 8 shakes …

10 10

ROTATING GOBO CHANGE

0 - 18 Empty position
19 - 37 Gobo 1
38 - 56 Gobo 2
57 - 74 Gobo 3
75 - 92 Gobo 4

93 - 111 Gobo 5
112 - 129 Gobo 6
130 - 150 Gobo 1 shakes at variable speed from slow (xx bpm) to fast (xx bpm)
151 - 171 Gobo 2 shakes at variable speed from slow (xx bpm) to fast (xx bpm)
172 - 192 Gobo 3 shakes at variable speed from slow (xx bpm) to fast (xx bpm)
193 - 213 Gobo 4 shakes at variable speed from slow (xx bpm) to fast (xx bpm)
214 - 234 Gobo 5 shakes at variable speed from slow (xx bpm) to fast (xx bpm)
235 - 255 Gobo 6 shakes at variable speed from slow (xx bpm) to fast (xx bpm)

11 11

GOBO ROTATION

0 - 21 Gobo indexing: 0° to 90° range
21 - 42 Gobo indexing: 90° to 180° range
42 - 63 Gobo indexing: 180° to 270° range
63 - 84 Gobo indexing: 270° to 360° range

84 - 105 Gobo indexing: 360° to 450° range

105 - 127 Gobo indexing: 450° to 540° range

128 - 190

Continuous gobo rotation at linearly variable speed from fast (180 rpm)
to slow (2.2 rph)

191 - 192 Stop rotation

193 - 255

Continuous gobo rotation at linearly variable speed from slow (2.2 rph)
to fast (180 rpm)

12 12

FINE GOBO ROTATION

0 - 255 Fine Gobo Indexing

37

SPHERISCAN - SPHERILIGHT

Channel Mode

DMX

Value

Function

S

tandard Vector

13 13

PRISM INSERTION

0 - 127 Prism out

128 - 255 Prism into the light beam

14 14

PRISM ROTATION

0 - 21 Prism indexing: 0° to 90° range
21 - 42 Prism indexing: 90° to 180° range
42 - 63 Prism indexing: 180° to 270° range
63 - 84 Prism indexing: 270° to 360° range

84 - 105 Prism indexing: 360° to 450° range

105 - 127 Prism indexing: 450° to 540° range

128 - 190

Continuous prism rotation at linearly variable speed from fast (80 rpm)
to slow (3 rph)

191 - 192 Stop rotation

193 - 255

Continuous prism rotation at linearly variable speed from slow (3 rph)
to fast (80 rpm)

15 15

FROST

0 - 255

Frost moves linearly into the light beam
Frost blades move from no-diffusion to maximum diffusion

16 16

ZOOM

0 - 255 Zoom linearly moves from narrow to wide beam

17 17

FOCUS

0 - 255 Focus moves linearly from far to near position

18 18

FINE FOCUS

0 - 255 Fine Focus positioning

19 19

FUNCTION

0 - 11 Unused range
12 - 24 Fast Pan/ Tilt Speed (default)
25 - 37 Normal Pan / Tilt Speed
38 - 50 Conventional Dimmer curve
51 - 62 Linear Dimmer curve (default)

63 -113 Free
114 - 127 Free
128 - 140 Standard Dimmer curve
141 - 152 Fast Gobo change
153 - 163 Normal Gobo change (default)
164 - 255 Free

The functions are activated/selected passing through the unused
levels range and staying in the necessary range for 5 seconds

20 20

RESET

0 - 25 Unused range

26 - 76

Zoom Reset

Zoom Reset sequence is activated passing through the unused levels
range and staying in this range for 5 seconds

77 - 127

Pan / Tilt Reset

Pan/Tilt Reset sequence passing through the unused levels range and
staying in this range for 5 seconds

128 - 255

Complete Reset

All-effects Reset sequence passing through the unused levels range
and staying in this range for 5 seconds

Continue

➔

38

SPHERISCAN - SPHERILIGHT

C

hannel Mode

D

MX

V

alue

F

unction

S

tandard Vector

21 21

LAMP CONTROL

0 - 25 Unused range

26 - 100

Lamp OFF
Lamp switch-off passing through the unused levels range and staying
in this range for 5 seconds

101 - 255

Lamp ON
Lamp switch-on passing through the unused levels range and staying
in this range for 5 seconds.

-

22

COLOUR TIME

0 - 255 Cyan - Magenta –Yellow

-

23

BEAM TIME

0 - 255 Dimmer - Frost - Prism –Focus - Zoom

-

24

GOBO TIME

0 - 255 Rotating Gobo

39

SPHERISCAN - SPHERILIGHT

BIT Seconds

0 Full

1 0.2
2 0.4
3 0.6

4 0.8
5 1
6 1.2
7 1.4
8 1.6
9 1.8
10 2
11 2.2
12 2.4
13 2.6
14 2.8
15 3
16 3.2
17 3.4
18 3.6
19 3.8
20 4
21 4.2
22 4.4
23 4.6
24 4.8
25 5
26 5.2
27 5.4
28 5.6
29 5.8
30 6
31 6.2
32 6.4
33 6.6
34 6.8
35 7
36 7.2
37 7.4
38 7.6
39 7.8
40 8
41 8.2
42 8.4

BIT Seconds

43 8.6

44 8.8
45 9
46 9.2

47 9.4
48 9.6
49 9.8
50 10
51 10.2
52 10.4
53 10.6
54

11

55
56

12

57
58

13

59
60
61 14
62
63

15

64
65
66 16
67
68

17

69
70
71 18
72
73

19

74
75
76 20
77
78
79 21
80
81

22

82
83
84 23
85

BIT Seconds

86

24

87
88
89 25

90
91

26

92
93
94 27
95
96

28

97
98
99 29
100
101
102 30
103
104

31

105
106
107 32
108
109

33

110
111
112 34
113
114

35

115
116
117 36
118
119

37

120
121
122 38
123
124
125 39
126
127

40

128

BIT Seconds

129

130 41
131
132

4

2

133
134
135 43
136
137

44

138
139
140 45
141
142

46

143
144
145 47
146
147

48

148
149
150 49
151
152
153 50
154
155

51

156
157
158 52
159
160

53

161
162
163 54
164
165

55

166
167
168 56
169
170

57

171

BIT Seconds

172
173 58
174
175
176 59
177
178

6

0

179
180
181 65
182
183

70

184
185
186 75
187
188

80

189
190
191 85
192
193

90

194
195
196 95
197
198

100

199
200
201 110
202
203
204 120
205
206

130

207
208
209 140
210
211

150

212
213
214 160
215

BIT Seconds

216

170

217
218
219 180

220
221

190

222
223
224 200
225
226
227 210
228
229

220

230
231
232 230
233
234

240

235
236
237 250
238
239

260

240
241
242 270
243
244

280

245
246
247 290
248
249

300

250
251
252

310

253
254

255

Follow cue

Data

TIME TABLE

CLAY PAKY S.p.A. - Via Pastrengo, 3/b - 24068 Seriate (BG) Italy - Tel. [phone] - Fax [phone] - www.claypaky.it

IST00U/001 – EN - PRELIMINARY - 12/2015